NIVELCO NIVOTRACK M-300 series Installation And Programming Manual

3.3 TEMPERATURE CLASSES UPPER TEMPERATURE LIMITS LOWER TEMPERATURE LIMITS EX MARKING TYPE TEMPERATURE CLASS AMBIIENT TEMPERATURE MAX MEDIUM- TEMPERATURE MAX TYPE ia d d+ia MT� -..., ME� -... - 40 °C - 40 °C - 40 °C M�A -..., M�C – M�D -..., M�G -... +80 °C MB� -…, MG� -… - 25 °C - 20 °C - 20 °C M�K -…, M�N -… +70 °C MEU -…, MGU -… T6 +70 °C +80 °C M�A -…, M�C -... M�D -…, M�G -... +95 °C MEU -…, MGU -… T5 +59 °C +95 °C M�A -…, ...

3.3 TEMPERATURE CLASSES UPPER TEMPERATURE LIMITS LOWER TEMPERATURE LIMITS EX MARKING TYPE TEMPERATURE CLASS AMBIIENT TEMPERATURE MAX MEDIUM- TEMPERATURE MAX TYPE ia d d+ia MT� -..., ME� -... - 40 °C - 40 °C - 40 °C M�A -..., M�C – M�D -..., M�G -... +80 °C MB� -…, MG� -… - 25 °C - 20 °C - 20 °C M�K -…, M�N -… +70 °C MEU -…, MGU -… T6 +70 °C +80 °C M�A -…, M�C -... M�D -…, M�G -... +95 °C MEU -…, MGU -… T5 +59 °C +95 °C M�A -…, ...

Type M ��-3 ��-6Ex M ��-3 ��-8Ex M ��-3 ��-GEx M ��-3 ��-HEx M ��-3 ��-AEx M ��-3 ��-BEx M ��-3 ��-JEx M ��-3 ��-KEx M ��-3 ��-CEx M ��-3 ��-DEx M ��-3 ��-LEx M ��-3 ��-MEx II 1 G EEx ia IIB T6…T4 0,5…5m II 1/2 G EEx d ia IIB T6…T4 0,5…5m Ex marking II 1 G EEx ia IIA T6…T4 5…10m II 2 G EEx d IIB T6…T4 II 1/2 G EEx d ia IIA T6…T4 5…10m Ex electrical data Uimax = 30 V Iimax = 140 mA Pimax = 1 W Ci < 15 nF Li < ...

6.7 SERVICE PARAMETERS P80: Current output test (mA) Going to this parameter, the actual current output (corresponding to the measured process value) will be displayed. By pressing ENTER E the (now blinking) current value can be set for any value between 3,9 and 20.5 mA. The current output has to show the same value which can be checked by an ampere meter, according to the description under 4.4. Press ENTER E to quit test mode and return the parameter address P97: b:a.aa Software code a.aa: Number of the software version b: Code of the specia ...

3. TECHNICAL DATA TYPE RIGID TUBE VERSION M�A..., M�C…, M�D..., M�G…, MTU…, MBU… FLEXIBLE TUBE VERSION M�K… M�N… RIGID PLASTIC VERSION MEU… MGU… Measured process values Level; two float version: interface level, level difference Nominal length (L) 0.5 m …4.5 m 2 m … 10 m 0.5 m … 3 m Material of the tube Stainless steel: 1.4571 (DIN) PFA coated st.st. Max. medium pressure 2.5 MPa (25 bar) 1.6 MPa (16 bar) 0.3 MPa (3 bar) Medium temperature -40 °C ... +130 °C see temperature chart Linearity with dry calibrati ...

Measuring is going on during programming in accordance with the old parameter set. New parameter set will be valid after returning to the Measurement to the Programming Mode. Steps and indications of the Full Parameter Access programming mode pressing Keys while Parameter Address is blinking while Parameter Value is blinking ENTER E Go to the Parameter Value Save the modification of the Parameter Value and return to the Parameter Address NEXT + UP Cancel all modifications of the actual programming phase. Pressing for 3 sec is required while ...