VintageView VP-X Installation Instructions

Wine Master Cellars, LLLP • 10645 E 47th Ave, Denver, CO 80239 • phone: 866.650.1500 • fax: 866.650.1501 • VintageView.com Required tools: •Level •Drill •6mm masonry drill bit (included - replacement bits may be obtained by request) •Hammer Starter Kit Included Parts: •1 Vino Pins Neck •1 Vino Pins Base •2 Wedge Anchor Bolts •6mm masonry drill bit Figure B 1. Mark the mounting hole locations - Reference Figure A below to verify appropriate minimum clearances around the Vino Pins in the desired installation area. Pierce the template through the 2 marks corresponding with the bottle direction chosen earlier. Use a level to ensure the printed template is horizontal along the long edge and mark the hole locations using a marker or pencil (Figure B). Note: For Magnum bottles (1.5L) increase the horizontal distance between the neck and base Pins by 1 inch from 7-1/2 inches to 8-1/2 inches (216mm). 4  3/8" 13" 7  1/2" 5/8" 2  3/4" 2  3/4" Figure A 2. Install the anchors - Drill a 6mm hole 1-1/2 inches (38mm) deep at the marked locations (Figure C). Remove as much of the dust from the holes as possible and push the Wedge Anchors into the holes. Tap the anchors into the holes with a hammer leaving approximately 7/8 inch (22mm) of the anchor exposed (Figure D). Figure C Extension Kit Included Parts: •1 Vino Pins Neck Extension •1 Vino Pins Base Extension •2 Studs Before you begin, choose the direction the bottle necks should point If the bottle necks are to point to the right, the base pin must be installed to the left of the neck pin. If the bottle necks are to point to the left, the base pin must be installed to the right of the neck pin. Critical Note: These installation instructions are for attaching Vino Pins only to solid masonry or concrete surfaces. If your wall surface does not meet this minimum requirement, please contact your VintageView supplier to obtain appropriate mounting hardware for your wall surface. Installing Vino Pins on wall surfaces that do not meet this minimum criteria may result in failure of the installation and serious damage or injury. Figure D

place the collars over the bolts extending from the wall (Figure E). If using extensions*, thread a stud into one end of the base extension pin and screw the starter base Pin onto the remaining exposed end and firmly hand tighten (Figure F). Connect any additional extensions in a similar fashion and repeat this process for the neck pins. 5. Install Pins - Locate the lower of the 2 anchors in your wall and ensure that you have the base side Vino Pin assembly (the side with the longer curve in it). Screw the Vino Pin on clockwise and firmly hand-tighten in place (Figure G). Repeat the process for the neck pin in the higher anchor hole (Figure H). Figure F Figure E Vino Pins with Collar Vino Pins Starter Vino Pins with one Extension Vino Pins with 2 Extensions *Optional Extensions *Optional Collars Figure H Vino Pins without Collar For product warranty information, please visit: VintageView.com/support/warranty We’re here to help, call us at 866-650-1500 with any questions. US Patents: 6,991,117 and 7,850,017 China Patent: ZL 2006 2 0173305.3 *IMPORTANT NOTICE: The Vino Pins are designed to accommo- date a maximum of 3 bottles deep - 1 starter plus 2 extensions. Any application outside of these parameters is not warranted by VintageView and may result in product and/or installation failure, property damage and/or bodily injury. Maintenance and Care - The Vino Pins should be regularly checked for tightness. Should any Vino Pin be found to be loose, tighten by hand until secure. If the face of the wall surface shows signs of breakage, discontinue use immediately until such time as the wall may be adequately repaired. Vino Pins may be cleaned with a damp cloth and mild detergent - abrasive cleaners, pads or steel wool should NOT be used as they may scratch the surface.

Neck side Neck pointing to the LEFT Neck side Neck pointing to the RIGHT Base side Neck pointing to the LEFT Important Note: When printing this template, select “None” from the Page Scaling option list. This will ensure that the page prints at the proper size. The length of the line below must measure 7-1/2 inches for proper spacing.