SEA SURF Series Manual 

SURF 11 67410720 Fig. 15 BACK FIXATION MOUNTING If the back fixing has to be screwed (Fig.16) and the (A) holes are used, the fixing must be cut at a distance of 2,55 inches from its end, if instead you use the other holes it is not necessary to do the cutting. The support must be positioned so that the operator is in perfect horizontal position (Fig.19). N.B.: During assembling the back and front fixations lubricate with water repellent grease. a d b 2,36 6,10 Min. 1078 2,36 6,10 Min. d WARNING: During installation, ma ...

SURF 10 67410720 INSIDE OPENING INSTALLATION Total stroke 15.74 inches - max. recommended stroke 14,96 inches Inside Outside Max. Opening Angle OUTSIDE OPENING INSTALLATION Inside Outside a b d max (inches) 8,26 7,87 7,48 8,66 8,26 7,87 9,05 8,66 8,26 9,44 9,05 8,66 9,84 9,44 9,05 10,23 9,84 9,44 6,30 6,30 6,30 5,90 5,90 5,90 5,51 5,51 5,51 5,11 5,11 5,11 4,72 4,72 4,72 4,33 4,33 4,33 5,90 5,51 5,11 6,30 5,90 5,51 6,70 6,30 5,90 7,08 6,70 6,30 7,48 7,08 6,70 7,87 7,48 7,08 105° 105° 105° 100° 100° 100° 95° 95° 95 ...

SURF 1) The Surf unit 2) Mechanical stop 3) Electronic control unit 4) Flashing lamp 5) Photocell Dx 6) Differential switch 16A - 0,03A 7) Photocell Sx 8) Start - stop push button with key 9) Antenna 10) Support for photocells with photocells 11) Warning notice Note: The motor must be mounted with the release turned up (Fig. 10) Release 661 P. 551 P. 397 P. 330 P. 5 feet 6 feet 8 feet 11,5 feet SURF 350/350 24V SURF 350/350 24V ENTRY EXIT 1 1 2 2 3 4 5 6 7 8 9 10 10 11 Fig. 9 Fig. 10 Leaf lenght Weight STANDARD INSTALLATIO ...

SURF 13 67410720 Max = 2,55 in. Fig. 24 Max = 2,95 in. Fig. 25 Warning: in case of screwed front the front DOES NOT HAVE TO INCLINE like showed in fig.22 when it reaches the limit stop, otherwise it can cause damages to electronical limit switches. fixation, fixation Front fixation NOTE: When placing the front fixation on the gate, consider the shift in comparison to the central axle of the operator (Fig.23). INSTALLATION OF THE MECHANICAL LIMIT SWITCH STOPS Stop in closing Fig. 22 2,40 in. 0,90 in. Fig. 23 Stop in open ...

as follows: A. The gate is rigid and straight and runs smoothly throughout its travel. B. The length of each gate leaf must not exceed 11,48 feet for SURF 350/350 24V, always respecting the graph; C. the weight of each gate leaf must not exceed 661 pound for SURF 350/350 24V always respecting the graph; D. The hinges are hardly anchored and are able to support the torque of the operator; they do not have irregular movements and/or any friction during the whole movement of the leaf. PRECAUTIONS SURF has been create ...

SURF 67410720 2 Rev. 04 - 06/2014 Details General An appliance shall be provided with an instruction manual. The instruction manual shall give instructions for the installation, operation, and user maintenance of the appliance. The installation instructions shall specify the need for a grounding-type receptacle for connection to the supply and shall stress the importance of proper grounding. The installation instructions shall inform the installer that permanent wiring is to be employed as required by local codes, and instructions for conversion ...

SURF 67410720 2 Rev. 04 - 06/2014 Details General An appliance shall be provided with an instruction manual. The instruction manual shall give instructions for the installation, operation, and user maintenance of the appliance. The installation instructions shall specify the need for a grounding-type receptacle for connection to the supply and shall stress the importance of proper grounding. The installation instructions shall inform the installer that permanent wiring is to be employed as required by local codes, and instructions for conversion ...

Annual Annual Annual Annual Annual Annual Annual Annual All the above described operations MUST be made exclusively by an authorized installer. Check the solidity and the stability of the gate, especially the points of support and/or rotation of the gate (pivots). Check the release function Check and grease the fixing pivots and the endless screw Check the integrity of the connection cables Verify the functionally and the conditions of the limit switch stops in opening and closing (where foreseen) Verify the good condition ...