Sealey GSA672 Instructions For Use

give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE. 1. SAFETY INSTRUCTIONS  Follow workshop Health & Safety rules, regulations and conditions when using grinder.  WARNING! Disconnect from air supply before changing accessories or servicing.  Maintain the grinder in good condition and replace any damaged or worn parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.  WARNING! Check correct air pressure is maintained and not exceeded. We recommended 90psi.  Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.  Wear approved safety gloves, eye and ear protection. If dust is generated wear respiratory protection.  Keep grinding tips in good condition for best and safest performance.  Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.  Secure unstable workpiece with a clamp, vice or other suitable holding device.  Ensure the grinding tip is secure in the collet.  Avoid unintentional starting.  Keep children and unauthorised persons away from the work area.  DO NOT hold the workpiece by hand. Use clamps or a vice to secure the workpiece.  DO NOT use the grinder for a task it is not designed to perform.  WARNING! DO NOT use grinder if damaged or thought to be faulty. Contact your local service agent.  DO NOT use grinder unless you have been instructed in its use by a qualified person.  DO NOT drop, throw or abuse the grinder.  DO NOT carry the grinder by the air hose, or yank the hose from the air supply.  DO NOT operate grinder if you are tired or under the influence of alcohol, drugs or intoxicating medication.  DO NOT carry grinder with your hand on the throttle in order to avoid unintentional starting.  DO NOT direct air from the air hose at yourself or others.  When not in use disconnect from air supply and store in a safe, dry, childproof location. INSTRUCTIONS FOR : GENERATION SERIES LONG REACH AIR DIE GRINDER MODEL No: GSA672 2. INTRODUCTION & SPECIFICATION Collet size. . . . . . . . . . . . . . . . . . . . . . . . Ø6mm Free speed . . . . . . . . . . . . . . . . . . . . .23000rpm Air consumption . . . . . . . . . . . . . . . . . . . 3.0cfm Operating pressure. . . . . . . . . . . . . . . . . . .90psi Air inlet size . . . . . . . . . . . . . . . . . . . . . 1/4”BSP Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.6kg Noise Power. . . . . . . . . . . . . . . . . . . . . . 90.1dB Noise Pressure. . . . . . . . . . . . . . . . . . . 101.1dB Powerful, Third Generation long reach die grinder. Contoured handle insulates user from chill and vibration. Directional, low noise air exhaust can be rotated 360° giving operator added protection. Includes 4-position air valve and throttle safety device. Original Language Version GSA672 Issue: 2 - 2/11/09 all-guides com

3.1.1. Ensure grinder throttle is in the "off" position before connecting to the air supply. 3.1.2. You will require an air pressure of 90psi and an air flow of 3.0cfm. 3.1.3.  WARNING! Ensure the air supply is clean and does not exceed 90psi. Too high an air pressure or unclean air will shorten the life of the grinder due to excessive wear, and may be dangerous, causing damage and/or personal injury. 3.1.4. Drain the air tank daily. Water in the air line will damage the grinder. 3.1.5. Clean compressor air inlet filter weekly. 3.1.6. Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The minimum hose size should be 1/4” I.D. and fittings must have the same internal bore. 3.1.7. Keep hose away from heat, oil and sharp edges. Check hose for wear and make certain that all connections are secure. 3.2. Couplings Vibration may cause failure if a quick change coupling is connected directly to the grinder. To overcome this, connect a leader hose to the grinder. A quick change coupling may then be used to connect the leader hose to the air line recoil hose. (See figs. 1 & 2. 3. PREPARING DRILL FOR USE 4. OPERATING INSTRUCTIONS  WARNING! Ensure you read, understand and apply safety instructions before use. 4.1 To mount a grinding tip place the smaller spanner provided across the flats on the shaft (just below the collet) to prevent the shaft from rotating. Loosen the collet using the larger spanner and drop the shaft of the selected grinding tip into the collet. Tighten the collet until the shaft of the grinding tip is secuely held. fig. 1 Risk of Hand Arm Vibration Injury. The GSA672 Long Reach Air Die Grinder, when operated in accordance with these instructions and tested in accordance with EN 28662-1: 1993 results in the following vibration emission declared in accordance with BS EN12096: 1996. Measured vibration emission value: .................. 3.11m/s² Uncertainty: ........................................... 1.24m/s² These values are suitable for comparison with emission levels of other tools that have been subject to the same test. This tool may cause hand-arm vibration syndrome if its use is inadequately managed. Recommended Measures to reduce risk of hand-arm vibration syndrome: This item represents a low Hand Arm Vibration risk to users. The calculated maximum usage period exceeds 8 hours. We recommend appropriate safety equipment is utilised and regular breaks for the operator are employed to reduce any residual risk of fatigue or repetitive strain injury. fig. 2 Original Language Version GSA672 Issue: 2 - 2/11/09

or performing maintenance. Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty. 5.1. If the air system does not include an oiler, lubricate the grinder daily with a few drops of Sealey air tool oil dripped into the air inlet. 5.2. Clean the grinder after use. 5.3. Loss of power or erratic action may be due to the following: a) Excessive drain on the air line. Moisture or restriction in the air pipe. Incorrect size or type of hose connectors. To remedy, check the air supply and follow instructions in Section 3. b) Grit or gum deposits in the grinder. If your model has an air filter (located in the area of the air inlet), remove and clean it. Flush the grinder out with gum solvent oil or an equal mixture of SAE No 10 oil and paraffin. Allow to dry before use. 5.4. For a full service contact your local Sealey service agent. 5.5. When not in use, disconnect from air supply, clean and store in a safe, dry, childproof location. 4.2. Connect the grinder to the air hose as in Section 3. 4.3 Adjust the flow of incoming air by rotating the chrome ring around the air inlet port at the rear of the tool. There are four positions to select from. 4.4 Place thumb on throttle safety pin and push forwards and down to start grinder. DO NOT allow grinder to free run for an extended period of time as this will cause accelerated wear. 5. MAINTENANCE NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode. 01284 757500 01284 703534 [email protected] Sole UK Distributor, Sealey Group, Kempson Way, Suffolk Business Park, Bury St. Edmunds, Suffolk, IP32 7AR www.sealey.co.uk Web email Original Language Version GSA672 Issue: 2 - 2/11/09