Supersonic SC-805 Instruction Manual

Enter belo w the Serial No. whi ch is located On the bottom of the ca bin et. Reta in this Informati on fo r future referen ce. Mode No. Serial No. This“bolt Of lighting” indicates uninsulated material within your unit which may cause an electrical shock. For the safety of everyone in your household, please do not remove product covering TO PREVENT FIRE OR SHOCK HAZARD,DO NOT EXPOSE THIS EQUIPMENTTO RAIN OR MOISTURE. TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, AND FULLY INSERT. The“exclamation point” calls attention to features for which you should read the enclosed literature closely to prevent operating and maintenance problems. The normal ventilation of the Ventilation warning: product shall not be impeded for intended use. Dripping warning: The product shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases,shall be placed on the product. SC-765 SC-805 PORTABLE STEREO RADIO CASSETTE RECORDER WITH MP3/CD/CD-R/USB/SD/MMC PLAYER PRE-DN PRE-UP REPEAT /MO/ST

press PRE-DN button to choose the back channel. -In the mp3 mode, press PRE-DN button to enter the back folder. -In the radio mode, press PRE-UP button to choose the next channel. -In the mp3 mode, 6.PRE-UP BUTTON 8.REPEAT/MO/ST BUTTON - Repeat a track CD/MP3/USB program. - Repeat mode : normal->repeat 1->repeat all-> repeat album ->normal. - Press MO/ST button once , to mono state. - Press MO/ST button twice , to stereo state, stereo is displayed(In FM mode).. EN-2 EN-3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 24 25 26 27 28 29 AUDIO AUX PLAYER JACK 30 31 1. 2. 3. 4.STOP/USB/SD BUTTON 5.PRE-DN 6. PRE-UP 7.LCD DISPLAY 8.REPEAT /MO/STBUTTON 9.VOLUME 10.PLAY/PAUSE BUTTON 11.MUTE BUTTON 12.EQ BUTTON 13.TIME/PROGRAM BUTTON 14.FUNCTION BUTTON 15.RANDOM/BAND BUTTON 16.SD/MMC CARD JACK POWER BUTTON REMOTE SENSOR STANDBY INDICATOR 17. 18. 19.AUX JACK 20.TUNING CONTROL 21. STEREO HEADPHONE JACK 22.CASSETTE COMPARTMENT 23.CASSETTE RECORDERS KEYS 24.LEFT&RIGHT SPEAKER BOXES 25.FM ANTENNA 26.BATTERY DOOR 27.SPEAKER WIRE CONNECTOR(R) 28.SPEAKER WIRE CONNECTOR(L) 29.AC MAINS 30.DOCKING JACK 31.CD DOOR USB JACK BASS BUTTON 1.POWER BUTTON -Press POWER button on 2.REMOTE SENSOR 3.STANDBY INDICATOR 4.STOP/USB/SD BUTTON - stop CD/MP3/USB/IPOD/SD/MMC playback; erase a CD program. Press and hold more than 1.5 sec change USB1.1/MMC(SD)media(only USB) 5. 7.LCD DISPLAY - show the AM/FM dial frequency - show the number of tracks 9.VOLUME - adjust volume level. 10.PLAY/PAUSE BUTTON - start or pause MP3/CD/USB/IPOD/SD/MMC play 11.MUTE BUTTON -Press the mute button allows CD / MP3 / USB / MMC / SD / TAPE / IPOD (AUX) / the RADIO to enter the mute state. 12.EQ BUTTON -Press the button to change EQ CD/MP3 / USB/ SD/MMC/IPOD/RADIO's music style. -When playing the music, push down this button is in the popular-jazz-OFF-classica-rock. 13.TIME/PROGRAM BUTTON -In standby mode, to setup the time of the unit. -program and review programmed track numbers. -In the working status, push down this button can on CD/MP3 / USB/SD/MMC for programming. Rotate the volume button to hold the CD/MP3 / USB/SD/TAPE/IPOD (AUX) / RAID the volume. 14.FUNCTION SELECT - select source of sound CD/USB/TAPE IPOD(AUX)/RADIO 15.RANDOM/BAND BUTTON - 16.SD/MMC CARD JACK - To listen to your SD/MMC card with Mp3 music files. 17.USB JACK -To listen to your USB flash memory stick with Mp3 music files. 18.BASS BUTTON - 19.AUX JACK -Push FUNC button , select MP3/AUX station. Play Mp3、DISCMAN、 WALKMAN AUX insert when no disc. In a CD/MP3 / USB/MMC/SD mode, press this button can be played at random. -The radio in the mode, press this button to select the FM STEREO, FM, AM. Press the BASS button can make the CD/MP3/USB/ MMC/SD/TAPE/IPOD (AUX) / RADIO into the BASS state. NOTE:Please take out the CD disc. 20.TUNING CONTROL -Rotate the TUNING control to find the desired stations. 21.STEREO HEADPHONE JACK - 3.5 mm stereo headphone jack. 22.CASSETTE COMPARTMENT. 23.CASSETTE RECORDERS KEYS RECORD ( ) - start recording PLAY ( ) - start playback F.REW ( )-rewind the tape toward the beginning. F.FWD ( )-advance the tape toward the end. STOP/EJECT ( ) - stop the tape - open the cassette compartment PAUSE ( ) - interrupt recording or playback. 24.LEFT&RIGHT SPEAKER BOXES 25.FM ANTENNA - to improve FM reception 26.BATTERY DOOR -to open battery compartment 27.SPEAKER WIRE CONNECTOR(R) 28.SPEAKER WIRE CONNECTOR(L) 29.AC MAINS - inlet for power cord. 30.DOCKING JACK -To listen to your DOCKING with Mp3 music files. 31.CD DOOR OPEN BUTTON - press here to open/close the CD door.

2.Press BAND to select the desired wave band:AM,FM,FM ST. 3.Tune to required station by Rotate BACK/ NEXT or press PRE-DN /PRE-UP. Manual tuning: Rotate BACK or NEXT and then release within 1 sec. Auto tuning: Press the play/pause button enter the automatic channel scan mode, and to be put automatically sets. Preset channel:(FM 30 Preset memories,AM 10 preset memories) (1)Rotate BACK/ NEXT Select desired station. (2) Press PROGRAM button once , The MEMORY number indicator begins steady in the display. (3) Press PRESET-UP OR PRESET- DN buttons to select the desired number. (4) Press PROGRAM button to save that station. (5) Repeat steps (1) to (4) procedures for other stations. 4.After end of program. press PRE-UP or PRE-DN to start play the frequency that you selected or Press number key on the remote control. 5.Rotate [VOL-]or [VOL +] to adjust the volume. 6.Extend TELESCOPIC ANTENNA to its full length if you are listening to FM broadcasting. 7.Turn off the radio by press FUNCTION button select other mode or press power button to off the unit. 8.Switch on again after shut down, the memory frequency still exists. MONO/STEREO -Press MO/ST button once,to mono state. -Press MO/ST button twice, to stereo state,stereo is displayed. Remote Control EN-5 EN-4 ,, ,, ,, ,, Using AC Power 1.check if the power voltage, as shown on the type plate located on the bottom of the set, corresponds to your local ac power supply. if it does not, consult your dealer or service centre . 2.connect the power cord to the ac mains inlet and the wall outlet. the power supply is now connected and ready for use. 3.to switch off completely, unplug the power cord from the wall outlet. unplug the power cord from the wall outlet to protect your set during heavy thunderstorms. Batteries (not included) Open the battery compartment and insert eight batteries, (preferably Alkaline) with the correct polarity as indicated by the + and - symbols inside the compartment. Batteries contains chemical substances, so they should be disposed of properly Incorrect use of batteries can cause electrolyt leakage and will corrode the compartment or cause the batteries to burst. Therefore: Do not mix battery types: e.g. alkaline with carbon Zinc. Only use batteries of the same type for the set. When inserting new batteries, do not try to mix old batteries with new ones. Remove the batteries if the set is not be used for a long time. type R-20, UM-1 or D-cells, POWER SUPPLY BASIC FUNCTION USE CLOCK to setup the time of the unit 1.connect the ac on( . 2.short according to the time button, the time will flashing on the lcd display. 3.press BACK、NEXT to select the number of the time. you can setup the time format by 12h or 24h. 4.press time button to confirm. 5.then you can set the hour and the minute with the same method of steps 3-4. 6. with the same method of steps 3-4. The following operation must be in standby mode) after setup the unit time, long press the time button can setup the unit begin working time , Note: after setup the beginning time, the lcd will display the radio/cd/usb/sd/tape/aux/ipod mode, Press the BACK or NEXT to choose the mode, then it press time button to affirm, otherwise it play usb or aux mode first.

1.Insert a blank tape into the tape deck. 2.Press CD button on. 3.Load a CD disc into disc compartment and select the desire track you want to record. 4.Press DISC PLAY/PAUSE button to play the desired track(passage) 5.Press RECORD key and the PLAY key will automatically engage. 6.Press PAUSE key to interrupt or edit recording. Press it again to resume recording. 7.Press STOP/EJ. Key to end recording. 8.To hear what you recorded, follow instructions in PLAY A CASSETTE TAPE PROGRAM METHOD (1)Press the [PROGRAM] key at STOP mode, system will go to PROGRAM mode. -The PRG icon and P01 will blink at 2Hz. This prompts the user to enter the first songs in the program PLAY list. (2)The user can select the desire tracks by using [NEXT], [BACK] keys. Once these keys are pressed, the Display will show the selected track. (3)After select the desired track, press [PROGRAM] key again and it will be stored in the memory. Mp3 Maximum 99 Maximum 20 tracks can be programmed when Repeat steps (2) to (3) procedures. (4)If press the [STOP] key during the program mode, then the selected TRACKs will be stored in the memory and return to STOP mode (Continuous Play mode) (5)If press the [PLAY] key during the program mode, it will start the program PLAY mode. PLAY start from P01 Track and CD RECORDING FROM THE RADIO 1.Tune to the desired radio station. 2.Press STOP/EJ. To open the cassette door. 3.Insert a suitable cassette into the cassette deck and close the cassette door. 4.Press RECORD to start recording. RECORD key and PLAY key go down simultaneously. 5.For brief interruptions ,press PAUSE .To resume recording, press PAUSE again. 6.To stop recording , press STOP/EJ. 7.To hear what you recorded, follow instructions in PLAYING a cassette tape. EN-6 USING THE CASSETTE UNDERSTANDING THE BUTTONS RECORD - Press to record from the radio or CD play. PLAY - Press to play cassettes. REW - From stop mode, press to rewind the tape toward the beginning. F.FWD - From stop mode, press to advance the tape toward the end. STOP/EJ. - Press to stop current tape activity or to open the cassette compartment door when no buttons are active. PAUSE - Press to interrupt tape play or record mode, press the second time to resume tape play or tape record mode. PLAY A CASSETTE TAPE 1.Press FUNC button select TAPE mode. 2.Press STOP/EJ.key to open the cassette compartment door. 3.Insert a recorded cassette and close the cassette compartment door. 4.Press PLAY to start playback. 5.To interrupt playback, press PAUSE ,To resume, press the key again. 6.Press REW/F.FWD to move tape to the desired starting point. 7.Adjust the volume to your desired listening level. 8.To stop the tape ,press STOP/EJ. - The keys are automatically released at the end of the tape, except if PAUSE has been activated. Erasing a program You can erase the content of the memory by: - While playing, press STOP button twice. - Opening the CD door - Select the other mode. USE DOCKING To listen to your DOCKING with Mp3 music files. 1.Connect to the DOCKING . 2.Press function selector to DOCKING/AUX to supply power and play DOCKING. -Press PLAY/PAUSE button to play or pause playback; -Press STOP button to stop playback; -Press BACK or NEXT to select tracks of the Docking; -Press and hold on BACK or NEXT more than 1.5 sec to forward or backward search fast intra track; -Press REPEAT button to repeat 1 track or repeat all tracks of the Docking. NOTE: Press BACK button once briefly to return to the beginning of the current track. 、 、 . To listen music with a mp3 discman walkman 1.Connect to the AUX . 2.press function selector to DOCKING/AUX, the sound source of the mp3 or discman or walkman will output from the unit. -Rotate the volume control to adjust the volume. -The unit can't control the player. -Connect AUX and DOCKING at the same time, the ipod will not playback . USE AUX

EN-9 EN-8 Note: at the mode of CD/MP3 / USB/MMC/SD,the lcd will display the number of song or the song playing time. if at the mode of docking/aux, the lcd will display the symbol of docking (au),or the unit time. -The unit don't support the HDD all and the portion usb with mp3 player. USB/MMC(SD) Audio functions 1)press function button or stop/usb/sd button to choose the usb or sd state. 2) PLAY/PAUSE 3) NEXT, BACK Skip search 4) Program Track(MP3 99 Track CD 20 Track ) 5) PLAYMODE : normal->repeat 1->repeat all-> repeat 1 folder->Shuffle ->normal (There is not repeat 1 folder mode in Program PLAY mode) 6) Maximum Folder : 99 Folders 7) Maximum File : 999 Files 8) USB_UP ( Select USB/MMC(SD)) - User can switch over USB to MMC(SD) with pressing [USB_UP] key(Key Pad STOP Long Key). - Then “- - -“ will be displayed. Press PLAY button to start playback . - If a device is successfully read, then the correspond device is ready to play a file. - If a device fails to be read, then “NO” will be appeared on the Display to indicate that there is no device . *Notice : If no device is attached or the player fails to read the device when a user switchover USB to MMC(SD) with pressing [USB_UP] key, then “NO” is displayed and the system moves into the STOP mode. -When the unit has not the disc,inserting the usb/sd card will automatically real usb/sd card, it read the USB first while having the USB. This CD-player can play Audio Discs,MP3 CD-R. Do not try to play CD-ROM,CDi,VCD,DVD or computer CD. 1. 、with the printed side facing up and press cd door gently to close. 4.press play/pause on the set to start playback. 5. note: cd/mp3 play will also stop when: -you open the cd compartment; -you select radio sound source; -the cd/mp3 has reached to the end. selecting a different track. during playback you can use back or next to select a particular track. if you have selected a track number in the stop or pause position, press play to start playback. press next once briefly for the next track, or press repeatedly until the desired track number appears in the display. press back once briefly to return to the beginning of a current track. press back more than once briefly for a previous track. finding a passage within a track 1.press and hold down back or next. the cd is played at high speed. 2.when you recognize the passage you want release back or next. normal playback resumes. different play modes:repeat repeat-play the current track continuously. repeat all-plays the entire cd continuously. playing tracks in random order after press the random button, the tracks will be played in random order. Press function button to CD state. 2.to open the cd door, press cd open button. 3.insert a mp3/cd or cd-r Press the pause button to pause play, press the play button back playing. 6.to stop cd playback , press stop. CD/MP3 PLAYER CD/MP3 Player Playing a CD/MP3 Playing a USB/SD Playing a USB/SD

No CD/MP3 inserted CD/MP3/USB/SD playback does not work CD/MP3/USB/SD badly scratched/dirty Replace/clean CD/MP3/USB/SD (see maintenance) The CD/MP3 skips tracks CD/MP3 damaged or dirty Replace or clean CD/MP3 - CD-R、is blank or the disc is not finalized Use a finalized CD-R. EN-11

Power consumption .............................................................AC 21 Watts Dimensions......................................................Approx.434 mm(L)x 214 mm(W) x 228 mm(H) Operation temperature.........................................................+5 ℃ - +35℃ RECEIVER SECTION Receiving Bands...................................................................AM/FM Tuning Range..........................................................AM:530-1710KHZ FM:88-108MHZ COMPACT DISC SECTION Optical Pickup...................................................................... .3-Beam Laser Frequency Response.............................................................100Hz - 16KH z AUDIO SECTION Power output .........................................................................Maximum 3 Watt x 2 Headphone Impedance ............................................................4 ~ 32 Ohms ACCESSORIES Instruction Booklet.....................................................................1 Remote contro.....................................................................1 CASSETTE SECTION Recording System.................................................................2 Tracks 2Channel (Stereo) Biasing System......................................................................DC bias Frequency Response ............................................................125 -6.3 K H z Wow And Flutter ................................................................... 0.35% WRMS (JIS) EN-12