PEERLESS DSX200 Installation And Assembly

ISSUED: 01-05-10 SHEET #: 125-9094-3 03-01-10 Installation and Assembly: Shelf Bracket for Media Device Secure two adjustment brackets (D) to shelf (A) using four 1/4-20 x 1/2 round phillips screws (G). Model: DSX200 C D A E F G High Shelf Position Low Shelf Position G G A A D D 1 B H Description Qty. Part # A shelf 1 124-1941 B right vertical support 1 124-1944 C left vertical support 1 124-1943 D adjustment bracket 2 124-1945 E M5 x 16 phillips screw 8 520-1189 F M5 x 25 mm phillips screw 2 520-9543 G 1/4-20 x 1/2 round phillips screw 4 510-9108 H safety belt 1 170-8039-1 Parts List USE BACK MOUNTING HOLES USE BACK MOUNTING HOLES

ISSUED: 01-05-10 SHEET #: 125-9094-3 03-01-10 Attaching to Wall Plate Hook right and left vertical supports (B and C) onto wall plate (not supplied) and secure using two M5 x 25 mm phillips screws (F). NOTE: Don’t fully tighten M5 x 25 mm phillips screws (F) until after Step 3 2 F C B Wall Plate (Not supplied) High Shelf Position Low Shelf Position E C C Wall Plate (Not supplied) Wall Plate (Not supplied) B B Secure adjustment brackets (D) to right and left vertical supports (B and C) using eight M5 x 16 mm phillips screws (E). Position right and left vertical supports (B and C) in desired location then tighten M5 x 25 mm phillips screws (F). 3 D D E F F

ISSUED: 01-05-10 SHEET #: 125-9094-3 03-01-10 Attaching Safety Belt Select slot in tray as shown in fig 4.1. Remove backing and attach one clear strip through slot and around edge of tray as shown in fig. 4.2. Repeat for other slot on other side of tray. NOTE: This material prevents fraying or cutting of the belt. 4 Fig. 4.1 Fig. 4.2 SLOT FRONT LIP CLEAR STRIPS Take one belt and hold it so that the tri-bar belt clip is facing as illustrated. Feed belt up through the slot you have chosen. Remember, belt only goes through outside slot. Now feed belt through belt clip as shown. Repeat on other side of tray using other belt. 1 2 3 5 A H Continue by sliding on one belt guide and tri-bar clip on each side of the buckle. Refer to drawing below. 6 TOP BOTTOM NOTE: Teeth face down TRI-BAR BELT CLIP

ISSUED: 01-05-10 SHEET #: 125-9094-3 03-01-10 BELT GUIDE BELT GUIDE Pull end of safety belt (H) out of bottom buckle slot and back down through top buckle slot. NOTE: Do not tighten safety belt (H). 4 5 Bottom buckle slot Top buckle slot Tighten safety belt (H) by pulling on loose end of safety belt. H 6 NOTE: To attach screen to wall plate, spacers may be needed. Refer to wall mount instructions for use of spacers.

ISSUED: 01-05-10 SHEET #: 125-9094-3 03-01-10 Make sure that attachment brackets (not included) are at desired tilt before installing to wall plate (not included). Measure display hole pattern before securing display to wall plate (not included). If display mounting pattern is larger than distance between vertical supports of shelf mount brackets, position attachment brackets on outside with ratchet handles facing outward as shown in Fig 7.1. If display mounting holes are smaller than distance between vertical supports of shelf mount brackets, position attachment brackets on inside with ratchet handles facing inward as shown in Fig 7.2. NOTE: Shelf will be offset to the right or left in this orientation. If display mounting holes are equal to distance between vertical supports of shelf mount brackets, position attachment brackets on right or left side of shelf mount brackets with ratchet handles facing outward as shown in Fig 7.3. NOTE: Vertical brackets can be mounted on right or left side of shelf as shown in light gray. Fig. 7.1 Fig. 7.2 Fig. 7.3 7 Vertical brackets Outside Vertical brackets inside Vertical brackets inside and Outside Large Mounting Hole Pattern 18.65" 18.65" ATTACHMENT BRACKETS VERTICAL BRACKETS ATTACHMENT BRACKETS VERTICAL BRACKETS ATTACHMENT BRACKETS VERTICAL BRACKETS RATCHET HANDLE RATCHET HANDLE RATCHET HANDLE Small Mounting Hole Pattern Same Mounting Hole Pattern © 2010, Peerless Industries, Inc. All rights reserved. All other brand and product names are trademarks or registered trademarks of their respective owners.