PEERLESS SR1G Installation And Assembly Manual

ISSUED: 01-10-07 SHEET #: 009-9033-2 03-12-07 Installation and Assembly: 32" - 60" Flat Panel TV Cart Models: SR1G, SR560G Max UL Load Capacity: 150 lb (68 kg) screen 50 lb (22.7 kg) per shelf This product is UL Listed. It must be installed by a qualified professional installer. �

ISSUED: 01-10-07 SHEET #: 009-9033-2 03-12-07 Note: Read entire instruction sheet before you start installation and assembly. • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-729-0307. • This product should only be installed by someone of good mechanical aptitude, and fully understands these instructions. • Never exceed the Maximum UL Load Capacity. • Always use an assistant or mechanical lifting equipment to safely lift and position equipment. • Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding power. • The cart is not affixed or secured to the floor, and may therefore tip over and/or fall if screen and/or stand is shaken or hit. Always monitor children and do not let children play alone around stand as they could get hurt by a falling screen. Not recommended for use in areas with heavy traffic. WARNING Table of Contents Parts List ...................................................................................................................................................................... 3, 4, 5 Assembling Cart ................................................................................................................................................................... 5 Attaching Screen Using Universal Plate with Adapter Brackets .............................................................................................. 10 Attaching Screen with VESA 100 Mounting Pattern............................................................................................................... 13 Attaching Screen Using a Dedicated Plate ............................................................................................................................ 14 Tools Needed for Assembly • level • phillips screwdriver

ISSUED: 01-10-07 SHEET #: 009-9033-2 03-12-07 Parts List SR1G SR560G Black Black Description Qty. Part Number Part Number A screen mount bracket 1 201-1156 201-1156 B hook plate 1 201-1157 201-1157 C shelf support 1 201-1158 201-1158 D shelf clamp bracket 1 201-1159 201-1159 E base 1 009-1223 009-1223 F universal plate 1 N/A 201-1110 G adapter bracket 2 N/A 200-0752 H upright 1 580-1180 580-1180 I glass shelf 1 590-1208 590-1208 J top cover 1 590-1210 590-1210 K button bumper 9 590-1209 590-1209 L 1/4-20 x 12mm decorative screw 14 520-2325 520-2325 M 1/4-20mm nut 12 530-1022 530-1022 N 5/16" flat washer 10 540-9406 540-9406 O 3/8-16 x 2.5" socket screw 3 520-9550 520-9550 P 7/32" allen wrench 1 560-9715 560-9715 Q 4mm allen wrench 1 560-9646 560-9646 R 6mm allen wrench 1 N/A 560-9716 S left leg 1 009-0220 009-0220 T right leg 1 009-0218 009-0218 U wheel caster 2 600-0044 600-0044 V wheel caster/brake 2 600-0045 600-0045 W joint connector nut 4 530-1037 530-1037 X 3/8-16 x 1.5" screw bolt 4 520-1329 520-1329 Y M10 x .402 ID lock washer 3 540-9424 540-9424 Z end cap 4 590-1032 590-1032 AA 1/4-20 x 20mm screw 2 520-2326 520-2326 BB 3/16 allen wrench 1 560-0071 560-0071 CC M4 x 12 mm serrated washer head socket pin screw 6 N/A 510-1079 DD M4 x 25 mm serrated washer head socket pin screw 4 N/A 510-1082 EE M5 x 12 mm socket pin screw 4 N/A 520-1064 FF M5 x 25 mm socket pin screw 4 N/A 520-1122 GG M6 x 12 mm socket pin screw 4 N/A 520-1050 HH M6 x 25 mm socket pin screw 4 N/A 520-1211 II M8 x 15 mm socket pin screw 6 N/A 520-1068 JJ M8 x 40 mm socket pin screw 4 N/A 520-1152 KK .219 ID x .5 OD x .5 HT spacer 4 N/A 540-1057 LL .344 ID x .75 OD x .5 HT spacer 4 N/A 540-1059 MM multi washer 6 N/A 580-1036 NN M6 x 20 mm socket pin screw 4 N/A 520-9554 OO M6 x 30 mm socket pin screw 4 N/A 520-1067 PP M8 x 25 mm socket pin screw 4 N/A 520-1101 QQ M10 x 15 mm socket pin screw 4 N/A 520-9262 Before you begin, make sure all parts shown are included with your product. Parts may appear slightly different than illustrated.

ISSUED: 01-10-07 SHEET #: 009-9033-2 03-12-07 MM Some parts may appear slightly different than illustrated. H D E A B C F LL KK W V U K Z Q T S G J Y P I CC DD EE JJ X FF NN PP II HH O GG QQ L OO R N M BB AA

ISSUED: 01-10-07 SHEET #: 009-9033-2 03-12-07 1 Insert four end caps (Z) into ends of left and right support legs (T & S) as shown. Z T S Guide left leg (S) towards base housing (E) as seen in fig.2.1. Then line up holes in base housing with holes in left leg. Fasten base housing to left leg using two 3/8-16 x 1.5" screw bolts (X) and two joint connectors (W), tighten using 3/16" allen wrench (BB) and 7/32" allen wrench (P) as shown in fig.2.2. Repeat for right side with right leg (T). 2 S X fig 2.2 W fig 2.1 E S

ISSUED: 01-10-07 SHEET #: 009-9033-2 03-12-07 3 Insert and screw casters (V & U) into holes of support legs (S & T). Attach casters with brake (V) to the back of left and right support legs (S & T). Attach casters without brake (V) to front of support legs (S & T) as shown. NOTE: Lock brakes on casters, for no sudden movements during installation. T V U S HAND THREAD HOLD WHEEL Attach upright (H) to base (E), as shown in in fig 4.2 using three 3/8-16 x 2.5" socket screws (O) and M10 x .402ID lock washers (Y). Tighten screws using 7/32" allen wrench (P) shown in fig. 4.1. 4 fig 4.1 E O H Y fig 4.2 CHORD MANAGEMENT HOLES

ISSUED: 01-10-07 SHEET #: 009-9033-2 03-12-07 SLOT fig 6 C Loosely attach four 1/4-20 x 12 mm screws (L), washers (N), and 1/4-20 nuts (M) to shelf support (C). 5 Slide shelf support (C) onto upright (H) so that 1/4-20 nuts (M) slide into slots of upright (H) as shown in figure 6 and detail 1. Slide shelf support to desired position, level, then tighten 1/4-20 x 12 mm screws (L) using 4 mm allen wrench (Q). NOTE: MAXIMUM OF TWO SHELVES Max height of top shelf is 34" from base. Max height of second shelf is 28" from base. M H DETAIL 1 C L N M 6

ISSUED: 01-10-07 SHEET #: 009-9033-2 03-12-07 Insert three button bumpers (K) into bottom of shelf clamp bracket (D). Attach shelf clamp bracket (D) to shelf support (C) using two 1/4-20 x 20 mm screws (AA) and two 1/4-20 nuts (M). For additional shelf installation, repeat steps 5 through 7. Insert six button bumpers (K) into shelf support (C). Place glass shelf (I) on shelf support. I K C 7 7-1 K 7A 7-2 Attaching Glass Shelf D C AA M • Do not overtighten, may cause glass to shatter or crack. WARNING

ISSUED: 01-10-07 SHEET #: 009-9033-2 03-12-07 Insert two 1/4-20 x 12 mm screws (L) into screen mount bracket (A), leaving 3/16" of exposed thread as shown in figure 11 and detail 3. J H Snap top cover (J) onto upright (H). 11 10 3/16" fig 11 DETAIL 3 L A Loosely attach six 1/4-20 x 12 mm screws (L), washers (N), and 1/4-20 nuts (M) to screen mount bracket (A). 8 Slide screen mount bracket (A) onto upright (H) so that 1/4-20 nuts (M) slide into slots of upright (H) as shown in figure 9 and detail 2. Slide screen mount bracket to desired position, level, then tighten 1/4-20 x 12 mm screws (L) using 4 mm allen wrench (Q). 9 L N A M A H SLOT fig 9 L DETAIL 2 M H

ISSUED: 01-10-07 SHEET #: 009-9033-2 03-12-07 Attach universal plate (F) to hook plate (B) using four M10 x 15 mm socket screws (QQ). Tighten screws using 6 mm allen wrench (R). 12 F B QQ Attaching Screen Using Universal Plate with Adapter Brackets For attaching screens with VESA 100 hole pattern, skip to page 13. 13 Attach hook plate (B) to screen mount bracket (A). B A 14 Insert two 1/4-20 x 12 mm screws (L) into holes indicated below for desired screen orientation. Tighten all screws using 4 mm allen wrench (Q). L L L 2° Backward Tilt 5° Forward Tilt No Tilt

ISSUED: 01-10-07 SHEET #: 009-9033-2 03-12-07 Note: "X" dimensions should be equal. • Tighten screws so adapter brackets are firmly attached. Do not tighten with excessive force. Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque. WARNING Installing Adapter Brackets Refer to Screen Compatibility Chart to determine the proper fasteners to use. To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place screen face side down. If screen has knobs on the back, remove them to allow the adapter brackets to be attached. Place adapter brackets (G) on back of screen, align to holes, and center on back of screen as shown in figure 15.1. Attach the adapter brackets to the back of the screen using the appropriate combination of screws, multi-washers, and spacers as shown in figure 15.3. Note: Top and bottom holes must always be used. Verify that all holes are properly aligned, and then tighten screws using a security allen wrench. • If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly secured, damage may occur to screen or product may fail. WARNING MEDIUM HOLE FOR M5 SCREWS SMALL HOLE FOR M4 SCREWS LARGE HOLE FOR M6 SCREWS fig. 15.2 G CENTER BRACKETS VERTICALLY ON BACK OF SCREEN X X fig 15.1 Notes: • The number of fasteners used will vary, depending upon the type of screen. • Multi-washers and spacers may not be used, depending upon the type of screen. • Use the corresponding hole in the multi- washer that matches your screw size as shown in figure 15.2. SCREWS SPACERS G fig 15.3 MULTI- WASHER MULTI-WASHER 15

ISSUED: 01-10-07 SHEET #: 009-9033-2 03-12-07 Mounting and Removing Flat Panel Screen Hook adapter brackets (G) onto universal plate (F), then slowly swing screen in as shown. Turn screws (G) clockwise at least six times to prevent screen from being removed as shown in detail 4. Note: Tighten using 4 mm allen wrench (R). Screen can be adjusted horizontally if desired. Note: It is important to lock screen down! To lock the screen down, fully tighten screws to adapter bracket as shown in detail 4. To remove screen from mount, loosen screws, swing screen away from mount, and lift screen off of mount. 16 G DETAIL 4 SCREWS F G • Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television. WARNING F

ISSUED: 01-10-07 SHEET #: 009-9033-2 03-12-07 17 Attaching Screen with VESA 100 Mounting Pattern • If screws don't get three complete turns in the screen inserts or if screws bottom out and hook plate is still not tightly secured, damage may occur to screen or product may fail. WARNING Choose hole pattern as shown in figure 17. Attach hook plate (B) to back of screen using four M4 x 12 mm screws. Tighten screws using an allen wrench. M4 X 12 MM SCREWS fig 17 Attach hook plate (B) to screen mount bracket (A). B A L L L 2° Backward Tilt 5° Forward Tilt No Tilt B 18 Insert two 1/4-20 x 12 mm screws (L) into holes indicated below for desired screen orientation. Tighten all screws using 4 mm allen wrench (Q). 19

ISSUED: 01-10-07 SHEET #: 009-9033-2 03-12-07 Attaching Screen to a Dedicated Plate Cable Management Run cords through upright (H) using cord management holes. 20 22 CORD MANAGEMENT H fig. 21.1 Attach adapter bracket to back of plasma screen using four socket pin screws, as shown. Tighten screws using security allen wrench. Attach hook plate (B) to the back of adapter plate as shown in fig. 21.1. Then attach hook plate (B) to screen mount bracket (A) as shown in fig. 21.2. 21 fig. 21.2 B A © 2007 Peerless Industries, Inc. All rights reserved. Peerless is a registered trademark of Peerless Industries, Inc. All other brand and product names are trademarks or registered trademarks of their respective owners.