METHVEN Promix Installation Sheet

with adjustable cartridge for flow and temperature 28391 5 Issue: N P age 1 of 2 Important – P lease read all of the instructions before installation T he S ink Mixer is designed for All P ressure systems. T he B asin Mixer is designed for Mains P ressure systems only. R ecommended water supply temperature range is 5 to 65°C, maximum 80°C . T hese mixers are not recommended for use in uncontrolled heating systems such as wetbacks or solar heater units unless a NE F A tempering valve is fitted. AS /NZS 3500 requires all hot water supplies to any sanitary fittings to be tempered to 55°C for NZ, and 50°C for Australia. AL L P IP E WO R K MUS T B E THO R O UG HL Y F L US HE D P R IO R TO INS T AL L ATIO N O F THE MIX E R . AN INL INE F IL TE R MUS T B E F ITTE D TO P R E V E NT F O R E IG N P AR TIC L E S DAM AG ING THE C E R AMIC C AR TR IDG E . Technical specifications O perating P ressure: Min: 35kP a, Max 1 000kP a. R ecommended 1 50 – 500kP a. Install a NE F A pressure limiting valve if supply pressure exceeds 1 000kP a. Inlet Connections: All ½” BS P Installation Instructions S ink Mixer A 35mm diameter hole is required in the bench top. T he bench top cannot exceed 40mm thick. S crew the mounting studs into the bottom of the sink mixer. C onnect the flexible inlet hoses to the mixer body. T he hot hose is marked with red stainless braiding. F it the base ring and O ring to the base of the sink mixer. P lace the hoses through the bench. F it the mounting gasket, the mounting plate and tighten the mounting nuts. T wo rubber washers are provided for the flexible hose connections to the nipples. Machined nipple ends are required to ensure a seal to the flexible hose nuts Installation Instructions B asin Mixer A 35mm diameter hole is required in the bench top. T he bench top cannot exceed 40mm thick. S crew the mounting studs into the bottom of the basin mixer. C onnect the flexible inlet hoses to the mixer body. F it the O ring to the base of the basin. P lace the hoses through the bench. F it the mounting gasket, the mounting plate and tighten the mounting nuts. T wo rubber washers are provided for the flexible hose connections to the nipples. Machined nipple ends are required to ensure a seal to the flexible hose nuts Hose R equirements

Warranty Warranty Warranty Warranty Methven warrants this product against manufacturing defects and that it is suitable for use under operating conditions specified in this instruction sheet. For your warranty, please refer to www.methven.com or call Customer Service New Zealand Australia USA UK 0800 804 222 1300 638 483 800 975 5409 0800 195 1602 Aerator Installations Aerator Installations Aerator Installations Aerator Installations Ceramic Cartridge Adjustment Ceramic Cartridge Adjustment Ceramic Cartridge Adjustment Ceramic Cartridge Adjustment Do not remove the ceramic cartridge from the mixer while carrying out the following adjustments. NOTE: The cartridge is fitted to supply maximum hot supply. Flow Adjustment Flow Adjustment Flow Adjustment Flow Adjustment Remove the indicator for the lever handle by carefully popping out with a small flat screw driver. Using a 2.5mm hex key, loosen the grub screw through the indicator hole in the handle. Pull the handle off the mixer. Insert a 1.5mm hex key into the hole in the top of the cartridge lever. Engage the grub screw at the bottom of the hole. Turn the key clockwise to reduce the maximum flow setting or anticlockwise to increase the maximum flow setting. Reverse instructions to re-assemble. Tempe Tempe Tempe Temperature Adjustment rature Adjustment rature Adjustment rature Adjustment Remove the indicator for the lever handle by carefully popping out with a small flat screw driver. Using a 2.5mm hex key, loosen the grub screw through the indicator hole in the handle. Pull the handle off the mixer. With a small screw driver carefully pry the red Temperature limiting ring from its locator. Turn the Temperature limiting ring clockwise (+) to increase maximum hot temperature, anti-clockwise (-) to reduce the maximum hot temperature. Replace the adjustment ring in the locator and push firmly to secure. The raised portion of the ring with the +/- markings should be to the front of the faucet. Reverse instructions to re-assemble.