Marson MT10 Integration Manual

MT10 MT10 (3.3V (3.3V Linear Linear Image Image Barcode Barcode Scan Scan Engine) Engine) Integration Integration Guide Guide Version 1.9 DATE: 2018/09/03

TABLE OF CONTENTS 1. 1. INTRODUCTION INTRODUCTION.....................................................................................................11 1-1. 1-1. MT10 MT10 Block Block Diagram Diagram................................................................................ 11 1-2. 1-2. Electric Electric Interface Interface........................................................................................22 1-2-1. 1-2-1. Pin Pin Assignment Assignment.............................................................................. 22 1-2-2. 1-2-2. Electric Electric Characteristics Characteristics................................................................55 1-2-3. 1-2-3. Flex Flex Cable Cable........................................................................................ 55 1-3. 1-3. Operational Operational Timing Timing................................................................................... 66 1-3-1. 1-3-1. Power Power Up Up..........................................................................................66 1-3-2. 1-3-2. Sleep Sleep (Idle) (Idle) Mode Mode........................................................................... 66 1-3-3. 1-3-3. Decode Decode Timing Timing................................................................................66 1-3-4. 1-3-4. Summary Summary of of Operation Operation Timings Timings.................................................77 2. 2. SPECIFICATIONS SPECIFICATIONS.................................................................................................. 77 2-1. 2-1. Introduction Introduction................................................................................................ 77 2-2. 2-2. Technical Technical Specifications Specifications......................................................................... 77 2-3. 2-3. Interface Interface....................................................................................................... 99 2-3-1. 2-3-1. UART UART Interface Interface............................................................................... 99 2-3-2. 2-3-2. USB USB Interface Interface................................................................................10 10 2-4. 2-4. Operation Operation Method Method....................................................................................11 11 2-5. 2-5. Mechanical Mechanical Dimension Dimension...........................................................................11 11 2-6. 2-6. Scanning Scanning Range Range...................................................................................... 12 12 2-6-1. 2-6-1. Typical Typical Scanning Scanning Range Range............................................................ 12 12 2-6-2. 2-6-2. Guaranteed Guaranteed Scanning Scanning Range Range................................................... 13 13 2-7. 2-7. Pitch Pitch Angle, Angle, Roll Roll Angle Angle and and Skew Skew Angle Angle.......................................... 14 14 2-8. 2-8. Specular Specular Dead Dead Zone Zone............................................................................... 15 15 2-9. 2-9. Curvature Curvature Degree Degree.................................................................................... 16 16 2-10. 2-10. Flex Flex Cable Cable Specification Specification..................................................................... 16 16 2-11. 2-11. Connector Connector Specification Specification......................................................................17 17 3. 3. INSTALLATION INSTALLATION.................................................................................................... 18 18 3-1. 3-1. Electrostatic Electrostatic Discharge Discharge Cautions Cautions.......................................................18 18 3-2. 3-2. Mechanical Mechanical Dimension Dimension.......................................................................... 18 18 3-3. 3-3. Window Window Materials Materials....................................................................................19 19 3-4. 3-4. Window Window Specifications Specifications.......................................................................... 20 20 3-5. 3-5. Window Window Care Care............................................................................................ 22 22 4. 4. REGULATIONS REGULATIONS.................................................................................................... 22 22 5. 5. DEVELOPMENT DEVELOPMENT KIT KIT........................................................................................... 23 23 6. 6. SLEEP SLEEP (IDLE) (IDLE) MODE MODE.......................................................................................... 24 24 7. 7. PARAMETER PARAMETER SETUP SETUP..........................................................................................25 25 8. 8. VERSION VERSION HISTORY HISTORY............................................................................................ 26 26

___________________________________________________________________________________ 1 1. 1. INTRODUCTION INTRODUCTION The MT10 Linear Image Barcode Scan Engine is designed for 1D barcode middle range reading, and high performance barcode scanning with optimal performance and easy integration. MT10 is ideal for integration into data terminals and other small mobile devices. The MT10 consists of 2 illumination LEDs, a high-quality linear image sensor and a microprocessor that contains powerful firmware to control all aspects of operations and enable communication with the host system over the standard set of communication interfaces. Two interfaces, UART & USB, are available. UART interface communicates with the host system over TTL-level RS232 communication; USB interface emulates a USB Keyboard device and communicates with the host system over USB. 1-1 1-1.. MT10 MT10 Block Block Diagram Diagram

___________________________________________________________________________________ 2 1- 1-22.. Electric Electric Interface Interface 1-2-1. 1-2-1. Pin Pin Assignment Assignment (Back View of MT10) Pin# UART USB I/O Description Schematic Example 1 VCC VCC ------------ Supply voltage input. Must always be connected to a 3.3V power supply. +3V3 2 GND GND ------------ Power and signal ground. 3 RXD ------------ Input UART TTL data input. Sipex® Vendor P/N: SP232ACT 4 TXD ------------ Output UART TTL data output. Sipex® Vendor P/N: SP232ACT Pin13 Pin1

___________________________________________________________________________________ 3 Pin# UART USB I/O Description Schematic Example 5 CTS Input When handshaking is enabled, host authorizes MT10 to transmit data on TXD line. Sipex® Vendor P/N: SP232ACT USB D+ Bidirectional Differential Signal Transmission ------------------------------------------ 6 RTS Output When handshaking is enabled, MT10 requests permission from host to transmit data on TXD line. Sipex® Vendor P/N: SP232ACT USB D- Bidirectional Differential Signal Transmission ------------------------------------------ 7 Power down Power down Output Active high, it indicates that the MT10 is in Sleep Mode (See Chapter 6 for details) ------------------------------------------ 8 Buzzer Buzzer Output Active high: Power-Up or a successful barcode decoded. PWM controlled signal can be used to drive an external buzzer for a successful barcode decoded (Good Read). R3 10R Buzzer Q1 2N3904 Q2 2N3904 R6 2K7 R7 6K8 R8 3K3 BZ BZ1 BZ_2.7K 2 1 HD1 1N 4148 1 2 + C8 10uF + - VCC

___________________________________________________________________________________ 4 Pin# UART USB I/O Description Schematic Example 9 LED LED Output Active high, it indicates the status of Power-Up or a successful barcode decoded (Good Read). LED1 GREEN 1 2 Q4 2N3904 R11 330R R13 4K7 Decode LED VCC 10 Boot 0 Boot 0 Input Reserved for production only. ------------------------------------------ 11 Trigger Trigger Input High: Power-up/Standby Low: Scanning Operation *Note: 1. Scanning operation continues until a barcode is successfully decoded or the trigger is released (pull high). To proceed to the next scanning operation, release (pull high) first and press (pull low) the trigger again. 2. Pull low at power-up will prompt the scan engine into firmware update mode. 12 Reset Reset Input Reserved for production only. ------------------------------------------

___________________________________________________________________________________ 5 1-2-2. 1-2-2. Electric Electric Characteristics Characteristics Symbol Ratings Min Max Unit VIH Input high level 2.0 3.6 V VIL Input low level 0 1.1 V VOH Output high level 2.9 V VOL Output low level 0.4 V |△VDDx| Variations between different VDD power pins 50 mV *Note: 1. Power Supply: VDD=3.3 2. Exposure to maximum rating conditions for extended periods may affect device reliability. 1-2- 1-2-33.. Flex Flex Cable Cable The flex cable is used to connect MT10 to the host side. There are 13 pins on the MT10 (engine) side and 12 pins on the host side. Please see 2-10 for more details of flex cable. Flex cable (P/N: 6351-0501113) Pin# Pin Assignment To Host 1 VCC 2 GND 3 RXD 4 TXD 5 USB D+ / CTS 6 USB D- / RTS 7 Power Down 8 Buzzer 9 LED 10 Boot0 11 Trigger 12 Reset *Note: Conforms to MARSON MT700/MT710D’s pin assignment. 1 12 12 1 (contact) (contact) Host Engine

___________________________________________________________________________________ 6 1-3. 1-3. Operational Operational Timing Timing This chapter describes the timing associated with the various operating modes of the MT10 including Power Up, Sleep Mode, and Decode Timing. 1-3- 1-3-11.. Power Power Up Up When power is initially applied, the MT10 is activated and begins the process of initialization. Once initialization (duration ≦ 10mS) is completed, the MT10 enters Standby Mode and is ready for barcode scanning. 1-3- 1-3-22.. Sleep Sleep (Idle) (Idle) Mode Mode The MT10 will enter Sleep (Idle) Mode and output a Power Down signal (Active high) after a programmable time period has elapsed without any activity. Please see Chapter 6 for more details about Sleep Mode. 1-3- 1-3-33.. Decode Decode Timing Timing In Standby Mode, The MT10 is activated by the Trigger signal which MUST be kept low for at least 20 ms until the successful scan is achieved, as indicated by the Buzzer/LED signals. In Sleep Mode, the MT10 can be waken up by the Trigger signal which MUST be kept low for at least 20 mS until the successful scan is achieved, as indicated by the Buzzer/LED signal. The total scan and decode time is approximately equal to the time from the Trigger signal going low to the Buzzer/LED signal going high. This time will vary slightly based on several factors including barcode quality, barcode type and the distance between MT10 and the barcode scanned. Upon a successful scan, the MT10 outputs the Buzzer/LED signal and keeps this signal for the duration of the transmission of the data decoded to the host side. The duration is about 75 ms. Therefore, the total duration of a typical scanning operation (from Trigger turning low to the end of Buzzer PWM signal) is also approximately 120mS.

___________________________________________________________________________________ 7 1-3- 1-3-44.. Summary Summary of of Operation Operation Timings Timings 1. The maximum duration of initialization is 10mS. 2. The maximum duration of scanning operation in Standby Mode is 120mS. 3. The minimum duration of waking up MT10 from Sleep Mode by Trigger signal is about 2 ms. 4. The maximum duration of waking up MT10 from Sleep Mode by Trigger signal and completing decode (when barcode is within optimal focus) is about 120ms 2. 2. SPECIFICATIONS SPECIFICATIONS 2-1. 2-1. Introduction Introduction This chapter provides technical specifications of the MT10 scan engine. Operating method, scanning range and scan angle are also presented. 2-2. 2-2. Technical Technical Specifications Specifications Optic & Performance Light Source 625nm visible red LED Sensor Linear Image Sensor Scan Rate 650 Scans/ sec Resolution 4mil/ 0.1mm Scan Angle 41° Print Contrast Ratio 30% Width of Field 140mm (13Mil Code39) Typical Depth Of Field (Environment: 800 lux) 4 Mil Code39: 36 ~ 70mm (4 digits) 5 Mil Code39: 30 ~ 95mm (4 digits) 10 Mil Code39: 21 ~ 201mm (4 digits) 15 Mil Code39: 35 ~ 285mm (4 digits) 13 Mil UPC/ EAN: 34 ~ 239mm (13 digits) Guaranteed Depth Of Field (Environment: 800 lux) 4 Mil Code39: 45 ~ 70mm (4 digits) 5 Mil Code39: 40 ~ 95mm (4 digits) 10 Mil Code39: 35 ~ 195mm (4 digits) 15 Mil Code39: 45 ~ 275mm (4 digits) 13 Mil UPC/ EAN: 40 ~ 230mm (13 digits) Physical Characteristics

___________________________________________________________________________________ 8 Dimension W14 x L11.9 x H7 mm Weight 1g Color Black Material PC Cable 13pin to 12pin flex cable Electrical Operation Voltage 3.3VDC±0.15VDC Working Current < 75mA (UART) ; < 85mA (USB) Standby Current < 35mA (UART) ; < 45mA (USB) Idle Current (Sleep Mode) < 300uA (UART) ; < 500uA (USB) Surge Current < 500 mA Connectivity Interface UART (TTL-level RS232) USB (HID Keyboard) User Environment Operating Temperature -20°C ~ 60°C Storage Temperature -20°C ~ 60°C Humidity 0% ~ 95%RH (Non-condensing) Drop Durability 1.5M () Ambient Light 100,000 Lux (Sunlight) Symbologies UPC-A/ UPC-E EAN-8/ EAN-13 Matrix 2 of 5 China Postal Code (Toshiba Code) Industrial 2 of 5 Interleaved 2 of 5 Standard 2 of 5 (IATA Code) Codabar Code 11 Code 32 Standard Code 39 Full ASCII Code 39 Code 93 Code 128 EAN/ UCC 128

___________________________________________________________________________________ 9 MSI Plessey Code UK Plessey Code Telepen Code GS1 Databar Regulatory ESD Functional after 4KV contact, 8KV air discharge (it requires housing that is designed for ESD protection and stray from electric fields.) EMC FCC – Part15 Subpart B (Class B) CE – EN55022, EN55024 Safety Approval IEC 62471 (Exempt Group) Environmental WEEE, RoHS 2.0 2- 2-33.. Interface Interface 2-3-1. 2-3-1. UART UART Interface Interface Below default values of communication parameters apply to both Standard mode and Command mode firmware. Baud rate: 9600 Data Bits: 8 Parity: None Stop Bit: 1 Handshaking: None Flow Control Timeout: None ACK/NAK: OFF BCC: OFF A. Standard Mode Firmware version: SM3-d-x.xx (MT10 P/N: 110P-A000000) Characteristics: (1) Configurable by scanning configuration barcodes or Ez Utility® (a PC-based software utility, available for download at www.marson.com.tw) (2) Supports hardware trigger only Interface Configuration Barcode:

___________________________________________________________________________________ 10 UART Scanning above barcode will set your MT10 to UART interface. B. Command Mode Firmware version: SM3-d-x.xx.CMD (MT10 P/N: 110P-4000000) Characteristics: (1) Configurable by commands sent from host or BEO® (a PC-based software utility, available for download at www.marson.com.tw) (2) Supports both hardware and software triggers Interface Configuration Barcode: Not supported. 2-3-2. 2-3-2. USB USB Interface Interface Firmware version: SM3-d-x.xx (MT10 P/N: 110P-A000000) Characteristics: (1) Configurable by scanning configuration barcodes or Ez Utility® (a PC-based software utility, available for download at www.marson.com.tw) (2) Supports hardware trigger only (3) Emulates a USB Keyboard device Interface Configuration Barcode: USB HID Scanning above barcode will set your MT10 to USB interface.

___________________________________________________________________________________ 11 22--4. 4. Operat Operation ion Method Method 1. At power-up, the MT10 sends the Power-Up signals over Buzzer and LED pins as an indication that the MT10 enters into Standby Mode and is ready for operation. 2. Once the MT10 triggered by either hardware or software method, it will emit a narrow, horizontal slab of light which is aligned with the sensor’s field of view. 3. The linear image sensor captures the linear image of barcode and produces an analog waveform, which is sampled and analyzed by the decoder firmware running on the MT10. 4. Upon a successful barcode decoded, the MT10 turns off the illumination LEDs, sends the Good Read signals over Buzzer and LED pins and transmits the decoded data to the host. 5. The MT10 may enter into Sleep Mode (Please see Chapter 6 for more details) after a period of inactivity in order to reduce power consumption. 2- 2-55.. Mechanical Mechanical Dimension Dimension Front View Side View Top View

___________________________________________________________________________________ 12 2- 2-66.. SScanning canning RRange ange 2- 2-66-1 -1.. Typical Typical SScanning canning RRange ange Test Condition: Barcode Length: Code39 – 4 characters EAN/UPC – 13 characters Bar & Space Ratio: 1 to 2.5 Ambient Light: > 500 lux Minimum & Maximum Scan Distance Symbology Resolution Distance No. of Encoded Characters Standard Code 39 (w/o checksum) 4 Mil 36 ~ 70 mm 4 char. 5 Mil 30 ~ 95 mm 10 Mil 21 ~ 201 mm 15 Mil 35 ~ 285 mm EAN 13 13 Mil 34 ~ 239 mm 13 char. Maximum Scan Width Symbology Resolution Barcode Length No. of Encoded Characters Standard Code 39 (w/o checksum) 13 mil 140 mm 27 char.

___________________________________________________________________________________ 13 2- 2-66-2 -2.. Guaranteed Guaranteed SScanning canning RRange ange Test Condition: Barcode Length: Code39 – 4 characters EAN/UPC – 13 characters Bar & Space Ratio: 1 to 2.5 Ambient Light: > 500 lux Minimum & Maximum Scan Distance Symbology Resolution Distance No. of Encoded Characters Standard Code 39 (w/o checksum) 4 Mil 45 ~ 70 mm 4 char. 5 Mil 35 ~ 95 mm 10 Mil 35 ~ 195 mm 15 Mil 45 ~ 275 mm EAN 13 13 Mil 40 ~ 230 mm 13 char. Maximum Scan Width Symbology Resolution Barcode Length No. of Encoded Characters Standard Code 39 (w/o checksum) 13 mil 140 mm 27 char.

___________________________________________________________________________________ 14 22--7. 7. PPitch itch AAngle, ngle, Roll Roll AAngle ngle and and Skew Skew AAngle ngle Be aware of the tolerance for the pitch, roll and skew angle of bar code you are trying to scan. Pitch Angle: ± 30° Roll Angle: ± 20° Skew Angle: ± 40°

___________________________________________________________________________________ 15 22--8. 8. Specular Specular Dead Dead Zone Zone Do not place the MT10 directly over the barcode. The light reflecting directly back into the MT10 from the barcode is known as specular reflection, which can make decoding difficult. The specular dead zone of MT10 is up to 5° depending on target distance and substrate glossiness. Specular Dead Zone: ± 5°

___________________________________________________________________________________ 16 22--9. 9. Curvature Curvature Degree Degree The curvature degree of a scanned barcode is specified as below: 22--10. 10. Flex Flex CCable able Specification Specification Below is the drawing of the flat cable(P/N: 6351-0501113) that comes with MT10. Barcode Code 39 (L=32 mm) Code 39 (L=43 mm) Resolution 13 mil (0.33 mm) 20 mil (0.51 mm) R R ≧ 15 mm R ≧ 20 mm d 40 mm PCS 0.9 (printed on photographic paper) Bottom View Top View Top View Bottom View (Stiffener) (Contact) (Contact) (Stiffener)

___________________________________________________________________________________ 17 22--11. 11. Connector Connector Specification Specification 12-pin Molex® FPC Connector (Molex P/N: 54548-1229), to be installed on Host side.

___________________________________________________________________________________ 18 33.. INSTALLATION INSTALLATION The MT10 scan engine is designed specifically for integration into customer's housing for OEM applications. However, the MT10’s performance will be adversely affected or permanently damaged when mounted into an unsuitable enclosure. Warning: The limited warranty is void if the following recommendations are not adhered to when mounting the MT10. 3-1. 3-1. Electrostatic Electrostatic Di Discharge scharge Cautions Cautions All MT10s are shipped in ESD protective packaging due to the sensitive nature of the exposed electrical components. 1. ALWAYS use grounding wrist straps and a grounded work area when unpacking and handling the MT10. 2. Mount the MT10 in a housing that is designed for ESD protection and stray electric fields. 3-2. 3-2. Mechanical Mechanical Dimension Dimension When securing the MT10 by utilizing the self-forming screws: 1. Leave sufficient space to accommodate the maximum size of the MT10. 2. Do not exceed 1kg-cm (0.86 lb-in) of torque when securing the MT10 to the host. 3. Use safe ESD practices when handling and mounting the MT10. Front View Side View Top View

___________________________________________________________________________________ 19 3-3 3-3.. Window Window Material Materialss Following are descriptions of three popular window materials: 1. Poly-methyl Methacrylic (PMMA) 2. Allyl Diglycol Carbonate (ADC) 3. Chemically tempered float glass Cell Cast Acrylic (ASTM: PMMA) Cell cast Acrylic, or Poly-methyl Methacrylic is fabricated by casting acrylic between two precision sheet of glass. This material has very good optical quality, but is relatively soft and susceptible to attack by chemicals, mechanical stress and UV light. It is strongly recommended to have acrylic hard-coated with Polysiloxane to provide abrasion resistance and protection from environmental factors. Acrylic can be laser-cut into odd shapes and ultrasonically welded. Cell Cast ADC, Allyl Diglycol Carbonate (ASTM: ADC) Also known as CR-39TM, ADC, a thermal setting plastic widely used for plastic eyeglasses, has excellent chemical and environmental resistance. It also has an inherently moderate surface hardness and therefore does not require hard-coating. This material cannot be ultrasonically welded. Chemically Tempered Float Glass Glass is a hard material which provides excellent scratch and abrasion resistance. However, un-annealed glass is brittle. Increased flexibility strength with minimal optical distortion requires chemical tempering. Glass cannot be ultrasonically welded and is difficult to cut into odd shapes. Property Description Spectral Transmission 85% minimum from 635 to 690 nanometers Thickness < 1 mm Coating Both sides to be anti-reflection coated to provide 1% maximum reflectivity from 635 to 690 nanometers at nominal window tilt angle. An anti-reflection coating can reduce the light that is reflected back to the host case. Coatings will comply with the hardness adherence requirements of MIL-M-13508.

___________________________________________________________________________________ 20 3-4. 3-4. Window Window Specifications Specifications Window Specifications for MT10 Integration Distance Tilt Angle (a) Minimum Window Size Horizontal (h) Vertical (v) Thickness (t) < 0.5mm (b) 0 0 18 mm 5.5 mm < 1 mm 10 mm (c) > +20° < -20° 32 mm 6 mm 20 mm (c) > +17° < -17° 48 mm 6.5 mm 30 mm (c) > +15° < -15° 64 mm 7 mm

___________________________________________________________________________________ 21 The window size must increase as it is moved away from MT10 and should be sized to accommodate the field of view and illumination envelopes shown below:

___________________________________________________________________________________ 22 3-5. 3-5. Window Window Care Care In the aspect of window, the performance of MT10 will be reduced due to any kind of scratch. Thus, reducing the damage of window, there are few things have to be noticed. 1. Avoid touching the window as much as possible. 2. When cleaning the window surface, please use non-abrasive cleaning cloth, and then gently wipe the host window with the cloth that is already sprayed with glass cleaner. 4. 4. REGULATIONS REGULATIONS The MT10 scan engine conforms to the following regulations: 1. Electromagnetic Compliance – CE EN55022, EN55024 2. Electromagnetic Interference – FCC Part15 Subpart B (Class B) 3. Photobiological Safety – IEC 62471 (Exempt Group) 4. Environmental Regulations – RoHS 2.0, WEEE

___________________________________________________________________________________ 23 5. 5. DEVELOPMENT DEVELOPMENT KIT KIT MARSON MB100 Demo Kit (P/N: 11A0-9801A20) enables the development of products and systems using the MT10 on the MS Windows OS platform. Besides the Multi I/O board (P/N: 2006-1007X00), the MB100 Demo Kit provides the software and hardware tools required for testing the MT10 applications before integrating it into the host device. Please contact your sales representative for ordering information. MB100 Multi I/O Board (P/N: 2006-1007X00) MB100 Demo Kit Accessories O: Supported X : Not Supported Interface Cable RS232 USB HID USB VCP External Y-cable o o o (P/N: 7090-1583A00) Internal Y-cable o o o (P/N: 5300-1315X00) Micro USB Cable x o o (P/N: 7005-9892A50) Due to the advantage of its small size, MB100 Multi I/O board is also suitable for being installed inside the host system, as an interface board connecting MT10 to the host device.

___________________________________________________________________________________ 24 6. 6. SLEEP SLEEP ((IDLE IDLE)) MODE MODE The Sleep (Idle) Mode is disabled by default. To enable Sleep (Idle) Mode, simply follow below instruction to configure the “Pre-Idle Time”, or the period of inactivity before MT10 enters Sleep (Idle) Mode, as appropriate. A. Standard Mode Firmware version: SM3-d-x.xx (MT10 P/N: 110P-A000000) Steps: 1. Scan SET MINUTE [.B030$] or SET SECOND [.B029$] 2. Scan two digit from the numeric barcode table below. 3. Scan SET MINUTE [.B030$] or SET SECOND [.B029$] Notes: Pre-Idle Time - Min: 10 sec, Max: 60 min & 60 sec

___________________________________________________________________________________ 25 B. Command Mode Firmware version: SM3-d-x.xx.CMD (MT10 P/N: 110P-4000000) Property Option Remark Sleep (Idle) Mode {MC11WT1} 0 Off 1 On Default : Off When enabled, scanner will automatically enter Sleep Mode after a period of inactivity(Sleep Mode timeout). Pre-Idle Time {MC11WT,1,0} A number from 0~60 (Minute) A number from 0~60 (Second) Default : 1 minute Sleep Mode timeout(10 sec ~ 60 min & 60 sec), the period of inactivity before the scanner enters Sleep Mode. Steps: 1. Send {MC11WT1} & {MC11WT,1,0} to the MT10 if you want to enable Sleep (Idle) Mode and set Pre-Idle Time as 1 minute. 2. The MT10 will return {MC11,OK} and {MC11,1,1,0} respectively as confirmation. 3. If you want above settings to be saved permanently in Flash ROM, send {MCMDWT1} to the MT10. Otherwise MT10 will be reset to default after wake up from sleep. Notes: Curly braces “{ }” must be included at both ends of each command. 7. 7. PARAMETER PARAMETER SETUP SETUP You can set up your MT10 using one of the following methods: 1. Standard Mode (F/W ver.: SM3-d-x.xx): Scan configuration barcodes from the Universal User’s Manual, or use Ez Utility®, both of which are available for download at www.marson.com.tw 2. Command Mode (F/W ver.: SM3-d-x.xx.CMD): Send software commands from the host, or use BEO®, which is available for download at www.marson.com.tw. Full list of software commands can be found in the Help File of BEO program, on the chapter Test Window/ Command Operation.

___________________________________________________________________________________ 26 8. 8. VERSION VERSION HISTORY HISTORY Rev. Date Description Issued Checked 1.0 2016.05.09 Preliminary Draft Release Shaw Jou 1.1 2016.05.11 Revised D.O.F Shaw Jou 1.2 2016.07.06 Revised Electric & Flex Cable Specification Shaw Jou 1.3 2016.10.31 Revised Sleep Mode command in Chapter 6 Shaw Jou 1.4 2017.06.21 Deleted Red Cell-Cast Acrylic Description Shaw Hus 1.5 2018.03.06 Revised P/N on page10&24 Shaw Jou 1.6 2018.03.15 Updated Chapter 1 and 1-1 on MCU. Updated Chapter 6 on Command Mode settings. Shaw Jou & Hus 1.7 2018.06.19 Updated Working Temperature. Shaw Jou 1.8 2018.07.23 Added Typical D.O.F & Guaranteed D.O.F Shaw Hus 1.9 2018.09.03 Updated Chapter 3-4 Shaw Hus Marson Technology Co., Ltd. 9F., 108-3, Mincyuan Rd., Sindian Dist., New Taipei City, Taiwan TEL: 886-2-2218-1633 FAX: 886-2-2218-6638 E-mail: [email protected] Web: www.marsontech.com