Holtkoetter 6317 Assembly Instructions

Voice: (800) 899-5444 • Fax: (888) 552-8661 e-mail: [email protected] www.holtkoetter.com ASSEMBLY INSTRUCTIONS FOR Major lamp parts manufactured in Germany by Holtkötter Leuchten GmbH. Bulbs manufactured in Germany by Osram GmbH. Final assembly by Holtkötter in South Saint Paul, MN. Holtkötter ® and Holtkötter Leuchten® are registered trademarks of Holtkötter. All Rights Reserved. © Holtkötter Halogen Pharmacy Lamp No. 6317 CAUTION, IMPORTANT SAFETY INSTRUCTIONS This portable luminaire has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of electrical shock. This plug will fit a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Never use with an extension cord unless plug can be fully inserted. Do not alter the plug. INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, EXPOSURE TO EXCESSIVE UV RADIATION OR INJURY TO PERSONS WARNING - To reduce the risk of FIRE, ELECTRIC SHOCK, EXPOSURE TO EXCESSIVE UV RADIATION OR INJURY TO PERSONS: 1. Turn off power/unplug and allow to cool before replacing bulb. 2. Bulb gets HOT quickly. Contact only switch/plug when turning on. 3. Do not touch hot lens, guard or enclosure. 4. Do not remain in light if skin feels warm. 5. Do not look directly at lighted lamp. 6. Keep lamp away from materials that burn. 7. Use only with a 100 Watt, bayonet base halogen bulb or smaller bulb. 8. Do not touch the bulb at any time. Use a soft cloth. Oil from skin may damage bulb. 9. Do not operate the portable luminaire with a missing or damaged guard, lamp containment barrier or UV filter. SAVE THESE INSTRUCTIONS Please make sure that the following parts for your lamp are enclosed: A. Reflector B. Aluminum Ring (attached to lamp) C. Glass Shield D. Allen Wrench (packed inside bulb box) E. Large Washer (2 each, already installed) F. Handle with plastic protector G. Small Plastic Washer (attached to reflector) H. Small Plastic Nut (attached to reflector) I. Bayonet Base Halogen Bulb J. Floor Lamp K. Foot Dimmer Care Instructions Use only a soft, dry cloth to clean. If necessary, a slightly damp, soft cloth may be used to spot clean. Do not use common household cleaners or brass cleaners on lamps or fixtures, as the lacquer on the outside of the brass may be damaged as a result. Enjoy your new Holtkötter lamp.

Major lamp parts manufactured in Germany by Holtkötter Leuchten GmbH. Bulbs manufactured in Germany by Osram GmbH. Final assembly by Holtkötter in South Saint Paul, MN. Holtkötter ® and Holtkötter Leuchten® are registered trademarks of Holtkötter. All Rights Reserved. © Holtkötter F H G C I A E Set Screw B D E Step 2. Loosen the set screw with the allen wrench (D). Then unscrew the aluminum ring (B) from the lamp arm. Remove one of the large washers (E). Bulb and Reflector Installation Step 4. Put the 100-Watt halogen bulb (I) into the socket. Hold the bulb at the porcelain grip, push it down slightly and turn it clockwise. BE CAREFUL NOT TO TOUCH THE BULB ENVELOPE WITH YOUR BARE HANDS. Note of Caution: The recommended replacement bulbs for this fixture are 100 W Osram Bayonet Base Halogen bulbs. Use of other brands of unknown quality may cause a risk of overheating. Step 5. Align the glass shield (C) with the small screw extending from the bottom of the socket. Place the small washer (G) and the small plastic nut (H) over the screw and finger tighten. Step 6. Next, screw on the handle (F) and finger tighten. DO NOT OVERTIGHTEN – THE GLASS SHIELD MAY CRACK UNDER TOO MUCH PRESSURE. Step 7. Plug the lamp cord into the foot dimmer and the cord from the foot dimmer into the wall outlet. Your lamp is now operational. Step 3. Slide the reflector (A) over the socket. Place the large washer (E) that was removed back onto the socket. Screw the aluminum ring (B) back onto the socket until it is tight. Tighten the set screw on the aluminum ring into place. DO NOT OVERTIGHTEN. MAKE SURE THE REFLECTOR IS STILL LOOSE ENOUGH TO TURN. Step 1. The brass arms are made of soft, high-quality brass that is pliable and may be bent from shipping. If necessary, apply pressure to straighten. Halogen Pharmacy Lamp No. 6317