Brother GTX-4 Setup Manual

Keep this manual in a safe place for future use. Please be sure to read "SAFETY INSTRUCTIONS" before use. Installation 1 Setup of the printer 5 Connection to a PC 17 Adjustment 23 Maintenance list 27 Table of contents

using your new printer, please read the "SAFETY INSTRUCTIONS" and handling instructions carefully. SAFETY INSTRUCTIONS 1. Safety indications and their meanings This instruction manual and the indications and symbols that are used on the printer itself are provided in order to ensure safe operation of this printer and to prevent accidents and injury to yourself or other people. The meanings of these indications and symbols are given below. Indications DANGER The instructions which follow this term indicate situations where failure to follow the instructions will result in death or serious injury. WARNING The instructions which follow this term indicate situations where failure to follow the instructions could result in death or serious injury. CAUTION The instructions which follow this term indicate situations where failure to follow the instructions may result in minor or moderate injury. IMPORTANT The instructions which follow this term indicate situations where failure to follow the instructions may result in damage to property. NOTE The instructions which follow this term indicate precautions and restrictions for use. Symbols This symbol ( ) indicates something that you should be careful of. The picture inside the triangle indicates the nature of the caution that must be taken. (For example, the symbol at left means "beware of injury".) This symbol ( ) indicates something that you must not do. This symbol ( ) indicates something that you must do. The picture inside the circle indicates the nature of the thing that must be done. (For example, the symbol at left means "you must make a ground connection".) 2. Notes on safety DANGER Contact with high voltage sections may lead to a serious injury. Turn off the power, and remove the cover 5 minutes later.

the machine yourself. Brother will not be held responsible for any accidents or problems resulting from modifications made to the machine. Do not handle the power cord with wet hands. Otherwise, it may cause electric shocks. Installation Do not set up the printer in a dusty environment. If dust collects inside the printer, it may cause fire or electric shocks or problems with correct operation. Be sure to connect the ground. If the ground connection is not secure, you run a high risk of receiving a serious electric shock, and problems with correct operation may also occur. Do not bend the cords excessively or fasten them too hard with staples or anything similar to secure cords. Otherwise it may cause fire or electric shocks. Printing If a foreign object gets inside the printer, immediately turn off the power, disconnect the power cord, and contact the place of purchase or a qualified technician. If you continue to use the printer while there is a foreign object inside, it may result in fire or electric shocks or problems with correct operation. Do not allow the printer to come into contact with liquids. Otherwise it may cause fire or electric shocks or problems with correct operation. If any liquid gets inside the printer, immediately turn off the power, disconnect the power cord, and contact the place of purchase or a qualified technician. Do not use the printer when smoke or a bad odor is coming from the printer. Otherwise it may cause fire or electric shocks or problems with correct operation. Immediately turn off the power, disconnect the power cord, and contact the place of purchase or a qualified technician.

rotating fan. Otherwise it will be caught up, which results in injuries. Turn off the power when you approach the fan. CAUTION Environmental requirements Use the printer in a place which is adequately ventilated. A slight odor is generated when the printed articles are being fixed by heat. Installation Setting up and moving of the printer should only be carried out by a qualified technician. The printer machine weighs 120 kg (265 lb). Transporting and setting up of the printer should be held in the proper way. Otherwise it may fall down and cause injury. When the printer falls down, disconnect the power cord and contact the place of purchase or a qualified technician. If you continue to use it, it may result in fire or electric shocks or poor printing quality. Do not place the printer on a shaky table or high shelf or other unstable location. Otherwise it may tip over or fall down and cause injury. Furthermore, the table that supports the printer should be at least 35.4 in. (90 cm) in width and 23.6 in. (60 cm) in depth, and should be able to bear a weight of 150 kg (330 lb) or more. Do not set up the printer in a place where it will be affected by vibration. Otherwise the printing quality may be degraded or the printer may fall down, which causes injury or results in failure of the printer. Do not connect the power cord until installation is complete. The printer may operate if the power is turned on by mistake, which could result in injury. Do not climb onto the printer or place heavy objects on top of it. Otherwise it may become unbalanced and tip over or fall down and cause injury. Be careful not to touch the claws of the mounting portion on the upper side of the rear cover. Otherwise you may be injured. Printing This printer should only be used by operators who are appropriately trained in its safe operation.

printer and avoid placing any objects. Otherwise your hand may get caught between the platen and an object, which may result in injury. Do not handle the platen while printing. If your hand gets caught between the platen or the T-shirt tray and the covers, it may be injured. Do not put your hands inside the covers while the printer’s power is turned on. Otherwise your hands may touch against moving parts and this may result in injury. When the pretreatment is applied to printed objects (like a T-shirt) with a spray or pretreatment applicator, sprayed mist is generated. So wear a pair of plastic gloves, a mask and protective glasses (or goggles) designed to shield against liquid splash, and fully take care of the air ventilation when you are working with it. When a problem occurs with the operation of the printer, contact the place of purchase or a qualified technician. Maintenance Be careful not to get your fingers caught when closing the front cover, otherwise it may result in injury to your fingers. When you mount or replace the head, be careful not to get your hands or fingers caught. Otherwise you may be injured. Do not disassemble the ink pouch. If the ink gets into your eyes or onto your skin, it may cause inflammation. In case of contact with eyes, do not rub but immediately rinse the eyes with water. Do not drink liquids such as the ink, maintenance solution, cleaning solution, pretreatment, or waste. They may cause diarrhea or vomiting. Avoid causing your eyes or skin to make contact with the ink, maintenance solution, cleaning solution, pretreatment or waste. It may cause inflammation. In case of contact with eyes, do not rub but immediately rinse the eyes with water. Keep the liquids out of the reach of children. Be sure to wear protective goggles and gloves when handling the grease, so that it does not get into your eyes or onto your skin. It can cause inflammation. Do not drink or eat the grease. It may cause diarrhea or vomiting. Keep the liquids out of the reach of children.

accessories, be sure to use only genuine Brother parts. Brother will not be held responsible for any accidents or problems resulting from the use of non-genuine parts. When replacing parts or installing optional accessories, be sure to follow the procedures described in the Instruction Manual. Incorrect procedures could cause injuries or problems. IMPORTANT Printing Do not move the platen by hand. Otherwise the printer may be mechanically and electrically damaged. Ensure there is adequate space left in front of the printer and avoid placing any objects. The platen may be hit and damaged. NOTE Use the printer in an area which is free from sources of strong electrical noise such as electrical line noise or static electric noise. Sources of strong electrical noise may cause problems with correct operation. Any fluctuations in the power supply voltage should be within ±10% of the rated voltage for the printer. Voltage fluctuations which are greater than this may cause problems with correct operation. The power supply capacity should be greater than the requirements for the printer’s power consumption. Insufficient power supply capacity may cause problems with correct operation. In the event of an electrical storm, turn off the power and disconnect the power cord from the wall outlet. Lightning may cause problems with correct operation.

This printer has the following warning labels displayed on it. Follow the precautions given on each warning label for your work. When the label is peeled off or illegible, contact the place of purchase. 1 4 5 6 7 2 3 X0028 Pretreatment 5 kg (11 lb) Waste ink tank Pretreatment 20 kg (44 lb) Ink pouch Maintenance solution pouch Grease 9 1 3 3 8 8 8 8 11 10 7 6 5 4 2 Cleaning solution Watch your fingers, or you may be injured. High temperature warning display

of this manual are abbreviated. Product names used in this manual are, in general, trademarks or registered trademarks of their respective developer or manufacture. However, in this manual, the ® marks or TM marks are not used. Brother logo is registered trademark of Brother Industries, Ltd. Apple, Macintosh, Mac OS, iOS, OS X, macOS, Safari, iPad, iPhone, iPod and iPod touch are the trademarks or registered trademarks of Apple Inc. in the United States and other countries. The official name of Windows® 7 is Microsoft® Windows® 7 operating system. (represented as Windows 7 in this manual) The official name of Windows® 8.1 is Microsoft® Windows® 8.1 operating system. (represented as Windows 8.1 in this manual) The official name of Windows® 10 is Microsoft® Windows® 10 operating system. (represented as Windows 10 in this manual) Microsoft®, Windows® 7, Windows® 8.1 and Windows® 10 are the trademarks or registered trademarks of Microsoft Corporation in the United States and other countries. Other product and company names mentioned herein may be the trademarks or registered trademarks of their respective owners. Information in this document and the specifications of this product are subject to change without notice.

Required Tools Phillips screwdriver: M3 to M5 Disassembling 1) Remove the Cover PANEL SIDE. 2) Remove the Lithium Battery (1) by pulling out the holder in the direction of the arrow. 3) Pickup the Lithium Battery (1) to the direction of the arrow. (1) (1) (1) Note based on California law (USA) on the use and handling of Perchlorate This product contains a CR Coin Lithium Battery which contains Perchlorate Material – special handling may apply. See http://www.dtsc.ca/gov/hazardouswaste.perchlorate.

Environment Temperature Humidity Keeping your printer 0°C (32°F) to 40°C (104°F) 20 % to 85 % (no condensation) Operating your printer *1 10°C (50°F) to 35°C (95°F) Printing-guaranteed range *2 18°C (64.4°F) to 30°C (86°F) 35% to 85 % (no condensation) Electrical Requirements Power Power Consumptions ― Single-phase 100-240 V, 50/60 Hz 0.8 A (Actual value) *1: Environmental range where the printer can be operated. *2: Environmental range where sufficient printing quality can be secured. X0285 34.1 in. (86.7 cm) Approx. 12.6 in. (32 cm) 16.7 in. (42.3 cm) 1.57 in. (40 mm) X0284 Exhaust 39.4 in. (100 cm) or more 39.4 in. (100 cm) or more 39.4 in. (100 cm) or more 15.7 in. (40 cm) or more 15.7 in. (40 cm) or more 35.4 in. (90 cm) or more 133.9 in. (340 cm) or more 106.3 in. (270 cm) or longer 23.6 in. (60 cm) or more Exhaust opening 1 Checking the installation site

direct sunlight or a large amount of dust.  The body size is 55.1 in. (width) x 51.2 in. (depth) x 21.7 in. (height) (140 cm (width) x 130 cm (depth) x 55 cm (height)) and the mass weighs 120 kg (265 lb).  Dimensions of the legs are 34.1 in. (86.7 cm) in width and 16.7 in. (42.3 cm) in depth. The diameter of the legs is 1.57 in. (40mm).  The height from the table to the top surface of the platen is approx. 12.6 in. (32 cm).  Do not use an extension cable.  Ensure ample work space of over 39.4 in. (100 cm) in front of and to each side of the printer is available. Also, as a space to install the rear cover, keep 15.7 in. (40 cm) or wider space in the back of the printer. Keep 15.7 in. (40 cm) or wider space in the ceiling direction as well. As the air is exhausted toward the rear side, keep 7.9 in. (20 cm) or more space from the exhaust opening.  The table that supports the printer should be at least 35.4 in. (90 cm) in width and 23.6 in. (60 cm) in depth, and should be able to bear a weight of 150 kg (330 lb) or more. The tabletop should be horizontal and should not rattle when the printer is running.  When installing the printer, place a level gauge on the top surface of the cover and the top surface of the platen to make adjustments so that the main unit is set horizontally.  In preparation for a major earthquake or other natural disasters, fix the table and the main unit with a tool like a fixing band to prevent the main unit from falling from the table. IMPORTANT Do not turn on the power until "P.5 Removing the protection materials" is completed. Otherwise the printer may fail. Unpacking 2 X0186

a AC power cord s Cable clamp d Grease f Clean stick R x 6 / Clean stick T x 6 g Cleaning cup h Filter cover / Fan filter x 2 j Gloves (for changing the wiper cleaner / for cleaning the maintenance unit) x 4 k Carriage fixing pin l Tweezers ; Flushing receiver x 2 / Flushing foam x 2 A Waste ink tank S Waste ink tube fixing rubber * The rubber is already attached to the waste ink tube of the machine. D Print head x 2 F Rear cover installation screw x 2 * Screws are already fixed with the machine. G Rear cover H Wiper cleaner J Adult platen K Setup Manual (this manual) ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑫ ⑬ ⑪ ⑯ ⑰ ⑱ ⑮ ⑭ X0286

accessories: - Ink pouch Black / Magenta / Cyan / Yellow x 1 (for each) White x 2 - Cleaning solution - Pretreatment - Wiper cleaner x 2 TIPS If you are not using white ink and using only color inks, then prepare a maintenance solution pouch instead of a white ink pouch. CAUTION The printer machine weighs 120 kg (265 lb). When transporting or installing the printer, make sure that it is held by four or more persons as illustrated above. Otherwise the machine may fall down, causing injury or resulting in failure of the printer. X0003 Transporting the printer 3

Remove all the tapes, strings and sheets shown in the below illustration. Mount the supplied accessories according to the following procedures. Please note that the platen should be mounted after turning on the power. Rear cover CAUTION Be careful not to touch the claws of mounting portion on the upper side of the rear cover. Otherwise you may be injured. X0004 X0005 Removing the protection materials 1 X0014 Mounting the supplied accessories 2

Filter cover and Fan filter Waste ink tank Fix the waste ink tank to the table leg or the like by using two pieces of string, etc. Insert the waste ink tube and the waste ink tube fixing rubber. IMPORTANT The waste ink tube contained in the waste ink tank should be cut down to around 1.6 to 2 in. (4 to 5 cm) remaining just inside the tank. If the tip of the waste ink tube is immersed in the liquid, it will prevent the smooth flow of the waste ink, to disable the ink suction operation of the head cleaning function. Avoid placing the waste ink tube horizontally as much as possible, and be sure not to let it bend. Otherwise the waste ink may have difficulty flowing through the tube. TIPS Install the waste ink tank in the front, because it must be emptied when the waste ink is full. X0024 X0023 X0292

Mount the following supplied accessories inside the printer. Open the cover to the direction a and shift the carriage to direction s. Put on the gloves that came with the printer and perform the following work. Flushing receiver Direct its orientation with the hole on the bottom to the front and push it in until it clicks (there is no difference in white and color sides; they can be mounted on either side). IMPORTANT Make sure that no flushing foam extends off the outboard end portions of the flushing receiver. If it does, it may interfere with the nozzle surface of the head and may result in a problem concerning firing of the print heads. Carriage fixing pin TIPS The carriage fixing pin will be needed when the power is turned OFF due to power outage while the printer is running and the recovery is not expected for a while. Secure the pin in the place illustrated above so as not to lose it. The front cover will not close completely if the carriage is fixed with the carriage fixing pin. X0287 ① ② X0006 X0187

regulations and laws. Use the cleaner by expiration date written on the label. Mount it on the machine immediately after it is unpacked. Insert the shaft (a), and push the area with the "PUSH" indication until it clicks (there is no difference in white and color sides; they can be mounted on either side). X0120 (a) X0008

Print head 1. There is no difference in white and color sides; they can be mounted on either side. IMPORTANT Changing the heads of white side and color side should be avoided once the inks are filled after mounting the heads. When you unpack the head, be careful not to touch the bottom of the head. Otherwise it may cause poor printing. When you mount the head, shift the carriage toward the center of the printer; to the position above the platen. If you perform the mounting of the head when the carriage is directly above the maintenance unit, it may damage the maintenance unit or the heads. TIPS The gray area (a) illustrated above may be hard and difficult to remove. If it is, use both hands to remove it. 2. Insert the head firmly to direction a. CAUTION When mounting the head, be careful not to move the carriage as much as can be avoided. Your hand may be caught in the carriage and injured. In addition, the tubes may be rolled together possibly damaging them. ① ① (b) X0010 (a) X0009

part as illustrated in (b) could come into contact with its bottom surface, which in turn may result in poor printing. Make sure to insert it to the end. 3. Push with force in the direction as indicated in s so that the (c) area makes contact with the side of the metal plate of the head (mount it in a similar way for the white or color side). CAUTION When you mount d, hold it down from the top. Otherwise your finger may be pinched and injured. 4. Remove the resin cover (d) by releasing two claws, and as illustrated above, connect the flat cable in such a way as not to become entangled. ③ ② (c) X0121 (d) X0011

5. Tuck the extra cable into the space as shown in area (e) for the color side. To eliminate the slack of the flat cable on the resin cover side, hold the cable down by using a clip as shown in a. Hook the two claws of the resin cover to mount the cover. 6. Remove four caps of the head. Check that the head and the marker of each tube are matched and connect the tubes one by one from back to front of the machine by rotating the nut until it stops. IMPORTANT Do not rotate the nut as illustrated in (f). It could disconnect the tube and leak the contained ink. Be sure to remove the caps attached to the head before connecting. M4 4 3 2 1 M C Y K C3 Y2 Bk1 M4 C3 Y2 Bk1 (f) X0012 (e) ① ① X0123

enough to open the lid of the tank and fill the tank with the cleaning solution until reaching the "FULL" line. When filling is completed, close the lid and slowly push the cleaning liquid tank back inside the printer for storage. IMPORTANT When you pour the cleaning solution, be sure not to exceed the "FULL" line. TIPS After filling the cleaning solution, make sure to push the cleaning liquid tank in to the end. The cleaning liquid tank that is not properly inserted causes an error and disables printing. Install the ink pouches into cartridges by referring to the illustrations on the label located on the ink bay cover of the machine. TIPS If you are not using white ink and using only color inks for printing, install a maintenance solution pouch instead of a white ink pouch, referring to the procedures from step 2. 1. Since there is a component within the white ink which becomes deposited, please be sure to shake the ink pouch before it is taken out of the box. Hold each edge of the carton containing the pouch tightly and shake it 100 times from side to side. Next, turn it upside down and shake it 100 times. 2. FULL LOW X0025 Filling the cleaning solution 3 X0016 Ink cartridge setup and installation 4

3. Open the lid of the ink cartridge. IMPORTANT When opening the lid, be sure not to touch portion (a). Otherwise, it could be damaged. Place the entire cartridge on a flat surface, push the latches on the bottom surface of the cartridge downward and open the lid. 4. Push the tip of the ink pouch in until it clicks. Straighten the ink pouch so that it can fit the grooves of the ink cartridge lid and mount it while pulling it by hand. TIPS If the edge of the ink pouch is bent or undulating significantly, make it straight with your hand. If you are using only color inks, set a maintenance solution pouch to the position W12 and W34. X0017 (a) X0178

CAUTION Be careful not to touch area (a) illustrated above. Otherwise you may be injured. 6. Stick the expiration date seal supplied with the ink pouch on the front side of the ink cartridge, install the cartridge in the correct color position in the machine and make sure that it is inserted into the machine until complete contact. K Y C M W 12 W 34 X0018 X0124 (c) (a) (b)

Close the cover of the machine and insert the AC power cord into (a) and the outlet. Press the power button (b) to turn the printer power ON. TIPS An error message "Perform Initial Ink Installation" may be displayed on the screen of the printer but it will be no problem, so please continue to perform the ink installation according to the procedures described in this manual. 1. Press on the operation panel to move the platen to the front. 2. Rotate the platen height adjustment lever in direction a, and align the scale to position "A". Mounting the platen 6 X0029 X0288 ① (b) (a) X0019 5 Turning on the power

lever in direction d. TIPS Use with the knob (a) tightened when printing. Perform this operation while the printer is in Standby mode. 1) -> [Language] -> Select your language -> 2) Press the power button to turn off the power. Turn on the power of the printer and perform the operation while the printer is in Standby mode. TIPS If you are using only color inks, perform the following procedures. -> [Maintenance] -> [White Ink Pause Mode] -> [Enable] Then follow the message and perform ink installation. 1) -> [Maintenance] -> [Initial Ink Installation] -> [All Print Heads] 2) Follow the precautions on the screen and press (It takes about 50 minutes). 3) When the printer returns to Standby mode, the operation will be completed. Installing the ink 8 Configuring the language 7 X0289 ② ③ (a)

1) Download the ZIP file from our website and unzip the file. 2) Double-click on "setup.exe" -> Activate the installer 3) Follow the instructions on the screen. 4) After the installation, restart the PC. 1) Connect the printer and PC via a USB2.0 cable. TIPS When putting the USB cable and LAN cable together, use "P.6 Cable clamp". 2) Once the next screen appears, the driver is automatically installed through the steps of [Skip obtaining driver software from Windows Update] -> [Yes] TIPS This screen may prompt more than once. And this also may require several minutes to complete. We recommend you to set "Brother GTX-4" or "Brother GTX-4 FileOutput" as the default printer for your convenience. TIPS Although the description of this section is based on operation with Windows, you can also use Macintosh. For details, please refer to "For Macintosh Instruction Manual". 1 Installing the driver When connecting via USB 2-A

TIPS The printer may not be recognized depending on your security environment. Consult the system administrator of the setting site. The static IP address can also be set on the printer. For details, refer to the Instruction Manual. 1) Perform the procedures of "P.17 When connecting via USB". 2) Start menu -> "Brother GTX-4 Tools" -> Activate "GTX-4 Maintenance" 3) Select [Set an IP Address] -> [Next] 4) Select the setting method -> [Next] 2-B When connecting via LAN

If you selected "Manually enter the IP address" 5) Enter the values of [IP Address][Subnet Mask][Default Gateway] -> [Next]. The steps are completed when the message [IP address was successfully assigned to the Printer.] is displayed. If you selected "Automatically acquire the IP address" 5) Enter the hostname -> [Next]. The steps are completed when the message [IP address was successfully assigned to the Printer.] is displayed.

1) Connect the printer and PC to a network using LAN cables and turn the printer power ON. 2) Windows 7: [Control Panel] -> [Devices and Printers] Windows 8.1: [Control Panel] -> [View devices and printers] Windows 10: [Settings] -> [Device] -> [Devices and Printers] 3) Click on [Add a printer] 4) Windows 7: Click on [Add a local printer] Windows 8.1: [The printer that I want isn't listed] -> Select [Add a local printer or network printer with manual settings] -> [Next] Windows 10: [The printer that I want isn't listed] -> Select [Add a local printer or network printer with manual settings] -> [Next] 5) Select [Create a new port] -> From [Type of port], select [Standard TCP/IP Port] -> [Next]

6) Enter the static IP address of the printer into [Hostname or IP address] -> Uncheck the check box of [Query the printer and automatically select the driver to use] -> [Next] TIPS If you set the printer's IP address by automatic acquisition, you must check the IP address of the printer in advance. You can confirm the IP address by selecting [Confirm network setting] -> [IP Address] from the menu. For details, refer to "8-20. Confirm network setting" in the Instruction Manual. If you are using a DNS server, you can use a host name and domain name instead of the IP address. In that case, enter the host name that has been acquired automatically and set for the printer IP address (see P.19). As for the domain name, check with your network administrator. 7) From [Device Type], select [Custom] -> [Settings] 8) From [Protocol], select [LPR] -> Enter "BINARY_P1" in the [Queue Name] of [LPR Settings] -> [OK] -> [Next] 9) Click on [Have Disk]

installer depending on the bits of Windows you use -> [OK] -> [Next] 11) Select [Replace the current driver] -> [Next] 12) Enter the [Printer name] -> [Next] 13) When the next screen appears, select [Do not share this printer] -> [Next] 14) When necessary, select [Set as the default printer] -> [Finish]

1) -> [Printer Setting] -> [CR Speed Adjustment] -> [Start (after cleaning/setup)] -> (It takes about 3 minutes.) 2) When the printer stops with a sound and the printer returns to Standby mode, the operation is completed. 1) Make sure that the platen height adjustment lever (a) is set at the "A" position. TIPS Use a platen sized 14 in. x 16 in. (356 mm x 406 mm), which is included at the time of your purchase. 1 Adjusting the carriage speed Checking the nozzle check pattern 2 X0290 (a)

below (Pretreated T-shirt is also acceptable). If the paper tends to be floated, tape the corners. 3) Perform the following operation on the screen of the printer: -> [Test Print] -> [Nozzle Check CMYK] -> 4) When printing is finished and the printer returns to Standby mode, set a piece of black paper or transparent sheet (such as OHP sheet) of A4 or letter size in the same manner as step 2 (A pretreated black or dark color T-shirt is also acceptable.). 5) -> [Test Print] -> [Nozzle Check White] -> 6) Check the printed results for both nozzle check prints and determine if there is a problem. If missing nozzles are found as indicated by the arrows below, there is a problem concerning the firing of the print heads. TIPS Even if the lines of the white-side printed result are light, since white ink is fired from more than one nozzle on the same place, the quality is not affected. 7) If any problem is found, perform a normal cleaning. While the printer is in Standby mode, press , select the head with the problem, and press . 8) Check the nozzle check pattern again. If the problem still persists, please contact your dealer. X0020 X0291

cable. On the PC side, "Brother GTX-4 Tools" -> Activate "GTX-4 Installation". 2) Prepare a few sheets of A4 or letter-size paper (black paper or transparent sheet such as OHP sheet and white paper), tape for fixing the paper, and a pretreated black or dark color T-shirt. TIPS For details for pretreatment, refer to the Instruction Manual. 3) Following the instructions on the Installation screen, run the following menu options. Menu name Things to prepare 1 [Initial settings after head replacement] *1 ― 2 [Firing Adjustment] Black paper or transparent sheet (such as OHP sheet) White paper 3 [Platen-Rolling Adjustment] White paper 4 [White/Color Alignment] Black paper or pretreated black or dark color T-shirt 5 [Setting of the time displayed on the nozzle check pattern] ― *1: In [Initial settings after head replacement], set the values written on the print head or the container. 3

For the White ink pause mode, perform the following steps using "GTX-4 Maintenace". Menu name When in White Ink Pause Mode 1 [Initial settings after head replacement] Performed for color head only Upon completion of color head setting, click [Cancel] to close the maintenance tool once and then start it. Then proceed to the following steps. 2 [Firing Adjustment] Performed for color head only Upon completion of color head setting, click [Cancel] to close the maintenance tool once and then start it. Then proceed to the following steps. 3 [Platen-rolling adjustment] Performed 4 [White/Color Alignment] Not required 5 [Setting of the time displayed on the nozzle check pattern] Performed TIPS For information on the White ink pause mode, see "7-3. What to do in the White Ink Pause Mode" in the Instruction Manual. 4) When the completion screen appears, click [OK] to finish the operation. TIPS If you want to check the value you have set, do not perform the above procedures as a means to verify them. The setting will be reset and returned to the initial value. To check the value in a proper way, refer to the Instruction Manual.

For details, refer to the Instruction Manual. Maintenance timing Description Error / Warning display Before printing Confirmation and disposal of waste ink ― Confirmation and replenishment of cleaning solution ○ Daily agitation of the white ink ○ Print out of the nozzle check pattern (checking on the print heads) ― When an error / warning is displayed Replacement of ink pouch with a new one ○ Cleaning of the nozzle guard, wiper, exhaust cap and suction cap ○ Replacing the wiper cleaner ○ Replacing the flushing foam ○ Replacing the fan filter ○ When the printer becomes dirty Head cleaning ― White ink circulation ― Cleaning the CR (carriage) plate ― Cleaning the internal area of printer ― Replacing the platen sheet ―

© 2017-2019 Brother Industries, Ltd. All Rights Reserved. *Please note that the contents of this manual may differ slightly from the actual product purchased as a result of product improvements. This is the original instructions.