croydon TI25 Instruction Manual

Estrada São Lourenço, 891 - Capivari - Duque de Caxias. RJ - Brasil - CEP 25243-150 Fax: 55 21 2676-2522 Phone: 55 21 2776-1928 / 55 21 2676-1512 e-mail: [email protected] INDUSTRIAL BLENDER - TI25-160001 W4 * Please read these instructions carefully before operation this appliance. IMPORTANT SAFEGUARDS - When using electrical appliances, basic safety precautions should always be observed including the following: - Before connecting your blender check if voltage of your power system corresponds to the same specified on the appliance. - To protect against risk of electrical shock, do not put cord, plug, base or motor in water or other liquids. - Never connect two or more appliances in the same plug. - When not in use, unplug the blender. - Avoid starting blender empty. - Avoid contact with moving parts because blades are sharp. "Handle carefully". - Keep hands and utensils out of container while blending to prevent the possibility of severe personal injury and or damage to blender. A plastic spatula may be used but must be used only when blender is "NOT RUNNING". - Only remove the container when blender "COMPLETELY STOPPED". INSTRUCTIONS FOR USE - Blender control is made by switch ( ON - OFF). - If blender action stops, turn blender off. Remove lid and use a plastic spatula to push mixture toward blades. Replace lid and continue. CLEANING PROCEDURE - Clean container (cup) with liquid soap and water filling to half capacity. - Turn on blender for some seconds. - Turn off blender, empty the container and rinse it. - Unplug blender clean body and external cup with a wet cloth. - Do not use harsh detergent or chemical products for cleaning. - Never use water jet or immerse appliance in water. - Wipe off appliance with a dry cloth and wait at least half an hour before re-connecting to the main power outlet. - If it’s necessary to disassemble the knife and the bushing follow the instructions of the fig. 1. - It's recommend to cut food in small pieces and maintain food below container's frieze height avoid spilling. - Place a small quantity os food with blender off. Turn on blender and add the rest of food that you want to process. - When blender is running do not remove the lid. TI25 TI25 TI25 TI25

Press Washer Washer Retainer Screw 5/16” Base Switch (On/Off) Nut 3/16” Container’s Support Screw 3/16” Washer Press Washer Nut 1/4” Latch Pin Latch Body Switch Cover Screw Motor Top Cover Cord Connection Motor Motor Cover Special Screw Press Washer Nut 1/2” Rabbet Screw 1/4” Blender Support Foot Shaft Chuck Nut Container Container Assembly O’ring Bushing (Chuck) Underfriction Washer Bracket Knife Nut Lid Latch Support Rubber Ring Nut Washer Press Washer Special Screw Gap Base Retainer Strain Relief Nut 5/16” Finishing Base 19 20 22 24 2526 29 30 31 32 33 35 36 39 40 (TI 25) (TI 25) 23 1 2 3 8 13 14 15 4 5 7 16 17 42 11 Technical Data Power (HP) Amperage (A) Speed (rpm) Capacity (l) Weight (Kg/lbs) Dimension W x H x D (cm/in) 9.0 1 ½ 3430 25 25.1/55.2 46/18.2 x 133/52.4 x 57/22.5 Voltage (V) 110 (60 Hz) INDUSTRIAL BLENDER 25 LITERS INDUSTRIAL BLENDER 25 LITERS item code description 44 46 45 41 9 47 48 10 27 5 51 21 50 28 43 6 L1 L2 G 110V 1 2 3 4 Wiring Diagram MOTOR SWITCH 7 OFF ON Procedure to Disassemble the Knife Procedure to Disassemble the Container Unscrew and remove four nuts 15 located under the base 8. Remove the pitcher. Lock the shaft 31 with the special tool and turn the nut 40 using the standard tool (Hex.3/8”). Remove the nut and all the movable pieces will be free. Procedure to Disassemble the Bushing 40 31 standard tool special tool FIG.1 To reassemble proceed in inverse sequence. Using the special tool, unscrew the bushing nut 32 and remove the bushing 36. TI25-160001 W4 37 37 52 53 49 38 34 12