Volt ShadowMaster VPL-1039 Installation Instructions Manual

VOLT® ShadowMaster™ LED Path & Area Light VPL-1039 INSTALLATION INSTRUCTIONS Specifications and product details subject to change without notice. © Copyright 2018, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved. [email protected] • 813.978.3700 - 1 - Help Hotline: 1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST) all-guide s.com

VPL-1039 Important: Please Read Before Installation Important Safety Instructions INSTALLATION INSTRUCTIONS ! ! w w w . v o l t l i g h t i n g . c o m - 2 - This luminaire is intended for installation in accordance with local codes and the National Electric Code (NEC). Failure to adhere to these codes and instructions may result in serious injury, property damage and void the warranty. These instructions do not intend to cover all variations in installation, operation maintenance or mounting situations. 1. Make sure that the power is turned OFF before installing or servicing this luminaire. 2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or more from pool, spa or fountain. 3. This luminaire is intended to be used only with a power supply (transformer) rated maximum of 300 watts (25 AMPS) at 15 volts. 4. Wiring connections must be made with wire connectors that are suitable for outdoor use. 5. Position the low voltage wire and wire connector so that it is located within 6 inches (15.2 cm) from a building structure, a luminaire or fitting. 6. The main low voltage cable is intended for shallow burial - less than 6 inches (152 mm). 7. If additional lengths of low voltage cable are required, please contact www.voltlighting.com or call 1-813-978-3700. INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS Lighted lamp is HOT! WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS. 1. Turn off/unplug and allow to cool before replacing lamp. 2. Lamp gets HOT quickly! Contact only switch/plug when turning on. 3. Do not touch the hot lens, guard or enclosure. 4. Keep lamp away from materials that may burn. 5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may damage lamp. 6. Do not operate the luminaire fitting with a missing or damaged shield. SAVE THESE INSTRUCTIONS

Package Contents A. (1) Fixture Body B. (1) Rod Product Dimensions 34.5” 11” - 3 - A. (1) XL Hammer Stake B. (1) LED Puck Light (pre-installed) C. D.

- 4 - Install Stake 1 Board Stake Soil Ground Determine the desired location for mounting the fixture. Hammer the stake into the ground until flange of stake is flush to grade. To avoid damage to the stake, place a board on top of the stake while hammering. NOTE: If the ground is hard and the stake is difficult to install, make a crosscut in the ground using a flat shovel. VOLT® ShadowMaster™ LED Path & Area Light VPL-1039 Clear away an area in the ground at the wireway slot on top of the stake. Lay the luminaire pigtail into the wireway slot and thread the fixture onto the stake. Tighten until snug. Thread the lock nut at the bottom end of the fixture against the stake and hand tighten until snug. Install Fixture to Stake 2 Pigtail Wireway Slot Lock Nut Fixture

- 5 - Wire Connections 3 Strip both leads from the luminaire pigtail. Using two wire connectors (sold seperately), connect the leads from the luminaire to the main supply cable leads. Pigtail Main Supply Cable Grease Filled Wire Connectors

© Copyright 2018, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved. [email protected] • 813.978.3700 w w w . v o l t l i g h t i n g . c o m - 7 - Help Hotline: 1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)