Sioux Chief StreamLine Installation Manual

TM With Full Mortar Bed Adapter Kit

Screws Strainer Height Adjustment Screw #10 2-1/2" Phillips Flat Head Screws. Note: Replaces Strainer Height Adjustment Screws from FreeStyle Linear Drain Brackets Foam Block Shower Pan Liner Square footage amount ordered separately based on shower size. Must comply with state and local codes Note: Replaces NobleSeal Flashing from FreeStyle Linear Drain Strainer to Base Screw #6 2-1/4" Phillips Pan Head Screws. Note: Replaces Strainer to Base Screws from FreeStyle Linear Drain Outside Corner Select outside corner material to match Shower Pan Liner material, PVC or CPE. Outside Corners ordered separately. Mortar Guard Bracket Screw #8 1/2" Phillips Pan Head Screws Strainer Height Adjustment Screw #10 2-1/2" Phillips Flat Head Screws. Note: Replaces Strainer Height Adjustment Screws from FreeStyle Linear Drain Brackets Foam Block Shower Pan Liner Square footage amount ordered separately based on shower size. Must comply with state and local codes Note: Replaces NobleSeal Flashing from FreeStyle Linear Drain Strainer to Base Screw #6 2-1/4" Phillips Pan Head Screws. Note: Replaces Strainer to Base Screws from FreeStyle Linear Drain Outside Corner Select outside corner material to match Shower Pan Liner material, PVC or CPE. Outside Corners ordered separately. Mortar Guard Brackets Bracket Screw #8 1/2" Phillips Pan Head Screws Strainer Height Adjustment Screw #10 2-1/2" Phillips Flat Head Screws. Note: Replaces Strainer Height Adjustment Screws from FreeStyle Linear Drain Brackets Foam Block Shower Pan Liner Square footage amount ordered separately based on shower size. Must comply with state and local codes Note: Replaces NobleSeal Flashing from FreeStyle Linear Drain Strainer to Base Screw #6 2-1/4" Phillips Pan Head Screws. Note: Replaces Strainer to Base Screws from FreeStyle Linear Drain Outside Corner Select outside corner material to match Shower Pan Liner material, PVC or CPE. Outside Corners ordered separately. Mortar Guard Foam Block Mortar Guard Bracket Screw #8 1/2" Phillips Pan Head Screws Strainer Height Adjustment Screw #10 2-1/2" Phillips Flat Head Screws. Note: Replaces Strainer Height Adjustment Screws from FreeStyle Linear Drain Brackets Foam Block Shower Pan Liner Square footage amount ordered separately based on shower size. Must comply with state and local codes Note: Replaces NobleSeal Flashing from FreeStyle Linear Drain Strainer to Base Screw #6 2-1/4" Phillips Pan Head Screws. Note: Replaces Strainer to Base Screws from FreeStyle Linear Drain Outside Corner Select outside corner material to match Shower Mortar Guard Bracket Screw #8 1/2" Phillips Pan Head Screws Strainer Height Adjustment Screw #10 2-1/2" Phillips Flat Head Screws. Note: Replaces Strainer Height Adjustment Screws from FreeStyle Linear Drain Brackets Foam Block Shower Pan Liner Square footage amount ordered separately based on shower size. Must comply with state and local codes Note: Replaces NobleSeal Flashing from FreeStyle Linear Drain Strainer to Base Screw #6 2-1/4" Phillips Pan Head Screws. Note: Replaces Strainer to Base Screws from FreeStyle Linear Drain Outside Corner Select outside corner material to match Shower Mortar Guard Bracket Screw #8 1/2" Phillips Pan Head Screws Strainer Height Adjustment Screw #10 2-1/2" Phillips Flat Head Screws. Note: Replaces Strainer Height Adjustment Screws from FreeStyle Linear Drain Brackets Foam Block Shower Pan Liner Square footage amount ordered separately based on shower size. Must comply with state and local codes Note: Replaces NobleSeal Flashing from FreeStyle Linear Drain Strainer to Base Screw #6 2-1/4" Phillips Pan Head Screws. Note: Replaces Strainer to Base Screws from FreeStyle Linear Drain Outside Corner Select outside corner material to match Shower Pan Liner material, PVC or CPE. Outside Corners ordered separately. Mortar Guard Bracket Screw #8 1/2" Phillips Pan Head Screws Strainer Height Adjustment Screw #10 2-1/2" Phillips Flat Head Screws. Note: Replaces Strainer Height Adjustment Screws from StreamLine Linear Drain Strainer to Base Screw #6 2-1/4" Phillips Pan Head Screws. Note: Replaces Strainer to Base Screws from StreamLine Linear Drain Shower Pan Liner1 Square footage amount ordered separately based on shower size. Must comply with state and local codes. Outside Corner Select outside corner material to match Shower Pan Liner material, PVC or CPE. Bracket Screw #8 1/2" Phillips Pan Head Screws Strainer Height Adjustment Screw #10 2-1/2" Phillips Flat Head Screws. Note: Replaces Strainer Height Adjustment Screws from FreeStyle Linear Drain Brackets Foam Block Shower Pan Liner Square footage amount ordered separately based on shower size. Must comply with state and local codes Note: Replaces NobleSeal Flashing from FreeStyle Linear Drain Strainer to Base Screw #6 2-1/4" Phillips Pan Head Screws. Note: Replaces Strainer to Base Screws from FreeStyle Linear Drain Outside Corner Select outside corner material to match Shower Pan Liner material, PVC or CPE. Outside Corners ordered separately. Mortar Guard Bracket Screw #8 1/2" Phillips Pan Head Screws Strainer Height Adjustment Screw #10 2-1/2" Phillips Flat Head Screws. Note: Replaces Strainer Height Adjustment Screws from FreeStyle Linear Drain Brackets Foam Block Shower Pan Liner Square footage amount ordered separately based on shower size. Must comply with state and local codes Note: Replaces NobleSeal Flashing from FreeStyle Linear Drain Strainer to Base Screw #6 2-1/4" Phillips Pan Head Screws. Note: Replaces Strainer to Base Screws from FreeStyle Linear Drain Outside Corner Select outside corner material to match Shower Pan Liner material, PVC or CPE. Outside Corners ordered separately. Mortar Guard 1 Shower pan liner (not included) will be used to waterproof shower. The NobleSeal flashing included with the drain will not be needed. *StreamLine Linear Drain is purchased separately from the Full Mortar Bed Adapter Kit. Shower pan liner and preformed corners ordered/purchased separately NobleSealant 150 Strainer Height Adjustment Tool Pre-Strainer Screw #8 1/2" Phillips Pan Head Screws Clamping Collar Screw #6 5/8" Phillips Flat Head Screws Strainer to Base Screw #6 1" Phillips Pan Head Screws. Note: Will not be used with Full Mortar Bed Kit. Strainer Height Adjustment Screw #10 1-1/4" Phillips Flat Head Screws. Note: Will not be used with Full Mortar Bed Kit. Base to Sub-Floor Screw #8 2-1/2" Phillips Course Deck Screws Base to Sub-Floor, Concrete Anchor 1" Long 1/4" Hole Strainer Height Adjustment Tool NobleSeal¨ Flashing Tube NobleSealant 150 Pre-Strainer Screw #8 1/2" Phillips Pan Head Screws Clamping Collar Screw #6 5/8" Phillips Flat Head Screws Strainer to Base Screw #6 1" Phillips Pan Head Screws. Note: Will not be used with Full Mortar Bed Kit. Strainer Height Adjustment Screw #10 1-1/4" Phillips Flat Head Screws. Note: Will not be used with Full Mortar Bed Kit. Base to Sub-Floor Screw #8 2-1/2" Phillips Course Deck Screws Base to Sub-Floor, Concrete Anchor 1" Long 1/4" Hole Strainer Height Adjustment Tool NobleSeal¨ Flashing Tube NobleSealant 150 NobleSeal® Flashing1 Pre-Strainer Screw #8 1/2" Phillips Pan Head Screws Clamping Collar Screw #6 5/8" Phillips Flat Head Screws Strainer to Base Screw #6 1" Phillips Pan Head Screws. Note: Will not be used with Full Mortar Bed Kit. Strainer Height Adjustment Screw #10 1-1/4" Phillips Flat Head Screws. Note: Will not be used with Full Mortar Bed Kit. Base to Sub-Floor Screw #8 2-1/2" Phillips Course Deck Screws Base to Sub-Floor, Concrete Anchor 1" Long 1/4" Hole Strainer Height Adjustment Tool NobleSeal¨ Flashing Tube NobleSealant 150 Pre-Strainer Screw #8 1/2" Phillips Pan Head Screws Clamping Collar Screw #6 5/8" Phillips Flat Head Screws Strainer to Base Screw #6 1" Phillips Pan Head Screws. Note: Will not be used with Full Mortar Bed Kit. Strainer Height Adjustment Screw #10 1-1/4" Phillips Flat Head Screws. Note: Will not be used with Full Mortar Bed Kit. Base to Sub-Floor Screw #8 2-1/2" Phillips Course Deck Screws Base to Sub-Floor, Concrete Anchor 1" Long 1/4" Hole Strainer Height Adjustment Tool NobleSeal¨ Flashing Tube NobleSealant 150 Pre-Strainer Screw #8 1/2" Phillips Pan Head Screws Strainer to Base Screw #6 1" Phillips Pan Head Screws. Note: Will not be used with Full Mortar Bed Kit. Pre-Strainer Screw #8 1/2" Phillips Pan Head Screws Clamping Collar Screw #6 5/8" Phillips Flat Head Screws Strainer to Base Screw #6 1" Phillips Pan Head Screws. Note: Will not be used with Full Mortar Bed Kit. Strainer Height Adjustment Screw #10 1-1/4" Phillips Flat Head Screws. Note: Will not be used with Full Mortar Bed Kit. Base to Sub-Floor Screw #8 2-1/2" Phillips Course Deck Screws Base to Sub-Floor, Concrete Anchor 1" Long 1/4" Hole Strainer Height Adjustment Tool NobleSeal¨ Flashing Tube NobleSealant 150 Base to Sub-Floor Screw #8 2-1/2" Phillips Course Deck Screws. Pre-Strainer Screw #8 1/2" Phillips Pan Head Screws Clamping Collar Screw #6 5/8" Phillips Flat Head Screws Strainer to Base Screw #6 1" Phillips Pan Head Screws. Note: Will not be used with Full Mortar Bed Kit. Strainer Height Adjustment Screw #10 1-1/4" Phillips Flat Head Screws. Note: Will not be used with Full Mortar Bed Kit. Base to Sub-Floor Screw #8 2-1/2" Phillips Course Deck Screws Base to Sub-Floor, Concrete Anchor 1" Long 1/4" Hole Strainer Height Adjustment Tool NobleSeal¨ Flashing Tube NobleSealant 150 Clamping Collar Screw #6 5/8" Phillips Flat Head Screws Pre-Strainer Screw #8 1/2" Phillips Pan Head Screws Clamping Collar Screw #6 5/8" Phillips Flat Head Screws Strainer to Base Screw #6 1" Phillips Pan Head Screws. Note: Will not be used with Full Mortar Bed Kit. Strainer Height Adjustment Screw #10 1-1/4" Phillips Flat Head Screws. Note: Will not be used with Full Mortar Bed Kit. Base to Sub-Floor Screw #8 2-1/2" Phillips Course Deck Screws Base to Sub-Floor, Concrete Anchor 1" Long 1/4" Hole Strainer Height Adjustment Tool NobleSeal¨ Flashing Tube NobleSealant 150 Strainer Height Adjustment Screw #10 1-1/4" Phillips Flat Head Screws. Note: Will not be used with Full Mortar Bed Kit. Pre-Strainer Screw #8 1/2" Phillips Pan Head Screws Clamping Collar Screw #6 5/8" Phillips Flat Head Screws Strainer to Base Screw #6 1" Phillips Pan Head Screws. Note: Will not be used with Full Mortar Bed Kit. Strainer Height Adjustment Screw #10 1-1/4" Phillips Flat Head Screws. Note: Will not be used with Full Mortar Bed Kit. Base to Sub-Floor Screw #8 2-1/2" Phillips Course Deck Screws Base to Sub-Floor, Concrete Anchor 1" Long 1/4" Hole Strainer Height Adjustment Tool NobleSeal¨ Flashing Tube NobleSealant 150 Base to Sub-Floor, Concrete Anchor 1" Long, 1/4" Hole Pre-Strainer Screw #8 1/2" Phillips Pan Head Screws Clamping Collar Screw #6 5/8" Phillips Flat Head Screws Strainer to Base Screw #6 1" Phillips Pan Head Screws. Note: Will not be used with Full Mortar Bed Kit. Strainer Height Adjustment Screw #10 1-1/4" Phillips Flat Head Screws. Note: Will not be used with Full Mortar Bed Kit. Base to Sub-Floor Screw #8 2-1/2" Phillips Course Deck Screws Base to Sub-Floor, Concrete Anchor 1" Long 1/4" Hole Strainer Height Adjustment Tool NobleSeal¨ Flashing Tube NobleSealant 150 823-FK24, 823-FK32, 823-FK40, 823-FK60 Full Mortar Bed Adapter Kit Hardware and Materials included: 823 SERIES StreamLine Linear Drain includes*: When using Full Mortar Bed Adapter Kit, discard installation instructions included with StreamLine drain and refer to these instructions. Carefully review all installation options and instructions before proceeding. StreamLine Linear Drain TM With Full Mortar Bed Adapter Kit Drain Base Pre-Strainers Strainer Clamping Collar

Type and Waste Pipe Location Drain hole is off-set to accomodate floor joist location. Size of shower determines size of drain to be used, which determines location of waste pipe through sub-floor. Match 2" I.D Schedule 40 pipetype (PVC or ABS) to drain base type. Pre-Planning Be certain to gather all required tools and materials required prior to installation. Sub Floor Caution: Sub floor must meet local code requirements and Tile Council of North America (TCNA) guidelines. Clean sub floor to be sure it is smooth and level. Pre-Sloped and Full Mortar Bed Requirements Follow manufacturers instructions. Use products recommended for the type of sloped bed being installed. StreamLine Linear Drain assembly is intended to install tight to toe plate and studs within shower PRIOR to installation of mortar bed, backer board, waterproofing and tile. Typical Drain Locations Drain at Back Wall Flush to back wall. Layout 1 Slope Drain at Full Curb Entry Flush to curb. Layout 2 Drain at Curb-less Entry Flush to both side walls. Layout 4 Drain at Partial Width Curb Flush to curb. Layout 3 Drain On Center Flush to both side walls. Layout 5 If StreamLine Linear Drain assembly is installed inside toe plates within shower, add a properly sloped mortar bed to fill the space between the toe plates and the drain base. Waste Pipe Location 15-3/4" 24" 1-1/4" 2-1/4" 1-3/8" 1-7/16" 1-5/8" 19-1/2" 32" 23-3/4" 40" 33-3/4" 60" www.siouxchief.com 2 Waste Pipe Location Fill Fill Installation Guide

Blocking Blocking between studs may be needed for Shower Pan Liner attachment prior to drain installation. 2. Sub-Floor Preparation Caution: Confirm that sub-floor meets all local code requirements and the Tile Council of North America’s (TCNA) guidelines. Check for Level. Clean Sub-floor must be smooth and level. Clean sub-floor. 3. Waste Pipe Option A: Waste Pipe Not Installed. Place, Mark and Cut Place drain base in desired location on sub floor. Mark waste pipe location on sub-floor. Cut opening in sub-floor to access plumbing below. Install Waste Pipe Follow local plumbing codes to properly install and secure 2" I.D. waste pipe 3/4" above sub-floor. Note: Waste pipe may be installed after fastening drain base if accessible from be low. Place Mark Cut Hole Blocking Sub-Floor Level 2" I.D. Pipe 3/4" 3 www.siouxchief.com Installation Guide

Mark Bed Slope 1/4" per foot slope to drain is required. Option B: Waste Pipe Pre-Installed Dry fit drain base over location of existing waste pipe. If location does not allow drain base to fit flush against at least 2 shower walls, move location of plumbing to allow for proper installation. May also require moving existing studs and toe plate. Dry Fit Alternate Drain Mounting Methods Recessed mount in concrete substrate Recessed mount in wood sub-floor Note: Any modification of substrate must comply with local building codes. Must Fit Flush to Sub-Floor Waste Pipe Front Edge of Drain Base 1/4" Per Foot Slope Mark Studs www.siouxchief.com 4 Installation Guide

For Concrete Sub-Floor A & B For Wood Sub-Floor B only A. Mark for Anchors Dry fit drain base over waste pipe. Mark all holes in outside flange of drain base on concrete floor. Remove drain base. Drill 1/4" holes, 1-1/2" deep where marked. Drive plastic anchors flush in all holes. B. Install Drain Base to Waste Pipe and Sub-Floor Caution: Confirm proper plastic pipe primer and cement for drain base type (PVC or ABS). Check drain base label to confirm. Apply appropriate plastic pipe primer and cement to drain and waste pipe following local plumbing codes and manufacturers instructions. Fit and fully seat drain base onto waste pipe. Fasten drain base to sub-floor by screwing 2-1/2" deck screws through all holes in outside flange of drain base into plastic anchors or directly into wood sub-floor. DO NOT OVER-TIGHTEN. 5 www.siouxchief.com Installation Guide

Protect Drain Base. Apply tape over entire top surface of drain base. Install Sloped Bed. Follow industry standards to complete sloped mortar bed installation. Be certain mortar completely fills void below drain base flange. Allow to dry before proceeding. Mortar Bed Tape www.siouxchief.com 6 7. Prepare Shower Pan Liner Option 1: For Drain at Back Wall Shower Pan Liner must turn up the walls a minimum of 3" above finished shower curb and 6" above floor in showers without curbs. Measure width of shower floor across drain base. Lay Shower Pan Liner flat. Measure and mark Shower Pan Liner. Fold and crease for upturns and create corners. Note: Do not secure Shower Pan Liner at this time. Tuck or Fold Fold See "Making Corners" on pg 8 for more information Installation Guide

Shower Pan Liner must turn up the walls a minimum of 3" above finished shower curb and 6" above floor in showers without curbs. Prior to installing Shower Pan Liner, install pre-formed outside corners (available separately) following manufacturer’s instructions. Two corners per side. Measure width of shower floor across drain base. Measure up and over curb. Lay Shower Pan Liner flat. Measure and mark Shower Pan Liner. Cut, fold and crease to proper size and fit. Note: Do not secure Shower Pan Liner at this time. Note: Preformed curbs may also be used. See manufacturer’s instructions. Inside Shower Outside Corners Under Liner 6" min. Outside Shower Outside Corners Under Liner 3" min. 7 www.siouxchief.com Installation Guide

Shower Pan Liner must turn up the walls a minimum of 3" above finished shower curb and 6" above floor in showers without curbs. Prior to installing Shower Pan Liner, install pre-formed outside corners (available separately) following manufacturer’s instructions. 2 per side. Measure width of shower floor across drain base. Measure up and over curb. Lay Shower Pan Liner flat. Measure and mark Shower Pan Liner. Cut, fold and crease to proper size and fit. Note: Do not secure Shower Pan Liner at this time. Note: Preformed curbs may also be used. See manufacturer’s instructions. Inside Shower 7. Prepare Shower Pan Liner (cont.) Tuck or Fold 6" min. Outside Corners Under Liner Outside Shower 3" min. Outside Corners Under Liner www.siouxchief.com 8 Making Corners Tucked Corner (when space is available between studs) Fold and crease to size. Tuck Shower Pan Liner into space between studs. Folded Corner Fold and crease to size. Fold corners behind shower pan liner. 6" Tuck between Studs 6" Fold Corners Behind Installation Guide

A. Seal Drain Base Lift out Shower Pan Liner. Remove tape, leaving tape over drain hole only. Apply a 1/8" continuous bead of NobleSealant 150 around chamfer on base flange and another bead in groove on drain base. B. Pre-Formed Corners Apply NobleSealant 150 to any pre-formed corners. C. Press Shower Pan Liner Into Sealant Align Shower Pan Liner, fit or re-tuck corners and firmly press Liner into sealant on drain base and any pre-formed corners. 7. Prepare Shower Pan Liner (cont.) Option 4: For Drain in Center of Floor Shower Pan Liner must turn up the walls a minimum of 3" above finished shower curb and 6" above floor in showers without curbs. Measure width of shower floor across drain base. Lay Shower Pan Liner flat. Measure and mark Shower Pan Liner. Fold and crease for upturns. Note: Do not secure Shower Pan Liner at this time. Preformed curbs may also be used. See manufacturer’s instructions. 2 Beads NobleSealant 150 Chamfer Groove Fold 6" min. 9 www.siouxchief.com Installation Guide

Align collar with drain base under Shower Pan Liner. Press firmly. Starting at one end, insert 5/8" screw through collar, punch through Shower Pan Liner and screw into base. Repeat for all screws. DO NOT OVER-TIGHTEN. 11. Cut Out Flashing With a razor knife, carefully trim out Shower Pan Liner from center of collar. Remove tape from drain hole. Caution: Do not puncture Shower Pan Liner outside of collar. 12. Flood Test Flood test as required by local codes. 13. Drain Drain and dry after successful flood test. 9. Fasten Shower Pan Liner Nail through top 1" of Shower Pan Liner to studs and/or blocking. Nail Cut Out Flashing Clamping Collar www.siouxchief.com 10 Installation Guide

Follow industry standards to install mortar bed flush to top of Mortar Guard 1-1/4" thick. Pack mortar into top and bottom of T-Channels to lock Mortar Guard in place. Be certain to maintain uniform thickness within entire bed. Allow to dry before proceeding. 16. Install Mortar Guard Install Mortar Guard over Foam Block and Brackets. Center end to end over Clamping Collar. Fully seat Mortar Guard to Clamping Collar on Drain Base. 14. Install Brackets Align holes in Bracket with second set of holes in from end of drain base. Attach using two 1/2" screws. Repeat for opposite end of drain base. DO NOT OVER-TIGHTEN SCREWS. 15. Install Foam Block Lay Foam Block in brackets and align ends of foam with inside edge of Clamping Collar. Bracket 1/2" Screws Mortar Guard Foam Block Foam Block Clamping Collar Align Full Mortar Bed T-Channel 1-1/4" thick 11 www.siouxchief.com Installation Guide

Place short leg of Pre-Strainer down, facing drain hole. Install 1/2" pan head screw, align strainer and tighten screw. Repeat for opposite strainer. Note: On 24" drain, place long leg of Pre-Strainer down, facing drain hole. 21. Install Height Adjustment Screws Screw in all 2-1/2" flat head height adjustment screws to approximately 1-5/8" above the clamping collar. 18. Remove Foam Block and Brackets Carefully remove Foam Block. Remove Bracket Screws and Brackets. 19. Install Backer Board and Wall Waterproofing Note: Plumbing codes and TCNA guidelines state that shower walls must be sealed with a vapor barrier or waterproofing membrane. Install 1/2" backer board and wall waterproofing according to manufacturer’s instructions. Caution: Do not puncture Liner. Short Leg 1/2" Screws Pre-Strainer Clamping Collar 1-5/8" 2-1/2" Screws From Full Mortar Bed Adapter Kit 1-5/8" www.siouxchief.com 12 Installation Guide

Note: Strainer attachment holes are not symmetrical. If screws do not align with holes in drain base, turn strainer end-to-end. Place strainer over height adjustment screws. Confirm that strainer is flush with all tiles. Fasten with three 2-1/4" pan head screws. DO NOT OVER-TIGHTEN. 24. Adjust Strainer Height Remove strainer. Remove tape from strainer. If factory installed film, start peeling at one end of strainer. Peel side to side (sawtooth pattern) to other end of strainer. Remove remaining residue by wiping with a soft cloth and WD40™ or Goo Gone™. Place thin end of height adjustment tool on tile and rest other end on height adjustment screw. Adjust screws so heads are flat against bottom of tool, and tool is flat against tile. Repeat for all height adjustment screws. 22. Temporarily Attach Strainer Note: Strainer attachment holes are not symmetrical. If screws do not align with holes in drain base, turn strainer end-to-end. Place strainer over height adjustment screws. Temporarily fasten with three 2-1/4" pan head screws. DO NOT OVER-TIGHTEN. 23. Tile and Grout Be certain strainer is protected with tape. Allow for 1/16" clearance between strainer and tile. Caution: Do not grout or seal this space. Tile and grout all surfaces following manufacturers instructions and TCNA guidelines. Strainer 2-1/4" Screws From Full Mortar Bed Adapter Kit Height Adjustment Tool Remove Strainer Adjust Screws 1/16" Cleanance Do Not Seal Or Grout Tile Strainer 2-1/4" Screws From Full Mortar Bed Adapter Kit 13 www.siouxchief.com Installation Guide

any hair or other obstructions from drain. Remove Strainer Re-Attach Strainer Note: Strainer attachment holes are not symmetrical. If screws do not align with holes in drain base, turn strainer end-to-end. Place strainer over height adjustment screws. Replace all three screws. DO NOT OVER-TIGHTEN. Strainer 2-1/4" Screws From Full Mortar Bed Adapter Kit Strainer 2-1/4" Screws From Full Mortar Bed Adapter Kit www.siouxchief.com 14 Installation Guide

PMG 1065 B.2/18 #IS-823FMB STREAMLINE FMB INSTALLATION INSTRUCTIONS