Sioux Chief Fire-Rated Ox Box Quick Start Manual

Plumb the supply lines in the typical manner. Open valves before soldering. Plumb the drain line in the typical manner. Wait for glue to cure before testing. Clip boxes together in desired configuration. Clip slides into tracks. Gently bend boxes together. This will allow the boxes to hold onto the stud. Secure with nails/ screws in the middle of the box clip and the top nailways. Sujete las cajas juntas en la configuración deseada. Sujete los lados adentro de las vías. Suavemente doble las cajas juntas. Esto dejara que las cajas sostengan sobre el montante. Asegure con clavos/ tornillos en medio de la caja de sujetar y los caminos de arriba de clavos. Install the frame after the wall has been finished. Aplome las líneas de provisión en la manera típica. Abre las válvulas antes de soldar. Aplome la línea de desagüe en la manera típica. Espera que el pegamento cure antes de probar. Instale el marco después que sea terminado la pared. 1 2 3 4 5 6 Ox Box ™ Fire-Rated Washing Machine Outlet Box Listed by Warnock Hersey��� ���� ������� ����� � �������� � to meet ASTM E-814 2 hours (F), 1½ hours (T) for 2-hour design 1 hour (F), 31 mins (T) for 1-hour design ASTM E-119 Package includes factory-installed intumescent pads. Ajuste a ASTM E-814 2 horas (F), 1½ horas (T) for diseño de dos horas 1 hora (F), 31 minutos (T) for diseño de la hora Ajuste a ASTM E-119 El paquete incluye almohadillas intumescentes instaladas por la fabrica. WASHING MACHINE Patents 7,360,553 & 7,735,511 Caja de Abertura de la Lavadora Patente 7,360,553 & 7,735,511 Includes: supply box with pad, drain box, box clip, 18" galvanized support bar Incluye: caja de provisión con una almohadilla, caja de desagüe, sujetador de caja, barra de soporte galvanizado de 18" Twist off small tip. Connect ⅝" O.D. compression fitting for air or water test. Remove the test cap by clamping and twisting off the test nipple. Tab folds into metal stud for added rigidity. Rompe la punta pequeña torciéndola. Conecta la parte suelta de compresión de ⅝ diámetro exterior a la prueba de aire o agua. Remueve la tapa de probar con abrazando y torciendo el pezón de probar. Los punteros doblen adentro del montante de metal para mas rigidez. Metal Stud Support Soporte de Metal del Montante Test the System Prueba el Sistema Remove Test Cap Remueve la Tapa de Probar

Peculiar, Missouri 64078 tel: 1-800-821-3944 fax: 1-800-758-5950 www.siouxchief.com DISTRIBuTED By #IS-696 FIRE-RATED WASHING MACHINE OX BOX INSTRuCTION SHEET – 1/08 © 2008 SIOUX CHIEF MANUFACTURING Design Specification 1 Wall Construction Wood or metal stud construction, max 100 in.² a of penetrations per 100 ft² of wall Single-layer ⅝" gypsum construction with 1-hour fire rating b Double-layer ⅝" gypsum construction with 2-hour fire rating c Boxes cannot be installed back to back d 2 Pipe/Box Support Each outlet box must be installed in a separate stud bay and a attached to the stud, as shown below in “over-stud” or “separate stud bay” installation examples. Fire rating does not apply to installations of two or more boxes in the same stud bay. Supplied support bar to be installed through at least one box’s slotted opening b Supply lines to be installed using ordinary methods c Drain line to be supported using ordinary methods d 3 Pipe Material 2" or larger metallic, PVC, or ABS DWV pipe a Metallic or plastic water supply pipe b 4 Firestop Device Sioux Chief fire-rated Ox Box frame and frame extension are a constructed using fire-rated resin. Boxes have 4" × 4" intumescent adhesive pads factory installed on the back of boxes. NOTE: Gaps up to ½" around box can be sealed with drywall plaster. Larger gaps require firestop sealant applied to opening spanning entire drywall depth. 1 2 3 4 Fire-rated ABS Intumescent pads Fire-Rated Ox Box ™ Outlet Box “over stud” installation “separate stud bay” installation The Fire-Rated Ox Box is certified by Intertek/Warnock Hersey to the following Fire Rating Standards: ASTM E-814 2 hours (F), 1½ hours (T) for 2-hour design 1 hour (F), 31 mins (T) for 1-hour design ASTM E119 CAN/uLC S115 2 hours (F), 1½ hours (T) for 2-hour design 1 hour (F), 31 mins (T) for 1-hour design uL 1479