Sealey WPC100A.V2 User Manual Manual

model no’s: thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE. wpC100.V2 wpC100a.V2 wpC150.V2 wpC150a.V2 wpC235.V2 wpC235a.V2 wpC250 wpC250a refer to instruction manual 1. saFetY 1.1. eleCtriCal saFetY � warNiNG! it is the user’s responsibility to check the following: check all electrical equipment and appliances to ensure that they are safe before using. inspect power supply leads, plugs and all electrical connections for wear and damage. sealey recommend that an rcd (residual current device) is used with all electrical products. You may obtain an rcd by contacting your local sealey dealer. if the pump is used in the course of business duties, it must be maintained in a safe condition and routinely PAt (Portable Appliance test) tested. electrical safety information, it is important that the following information is read and understood. 1.1.1. ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. 1.1.2. regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure. 1.1.3. important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct fuse - see fuse rating in these instructions. 8 DO NOt pull or carry the appliance by the power cable. 8 DO NOt pull the plug from the socket by the cable. 8 DO NOt use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or replaced immediately by a qualified electrician. 1.1.4. This product is fitted with a BS1363/A 13 Amp 3 pin plug. if the cable or plug is damaged during use, switch the electricity supply and remove from use. Ensure that repairs are carried out by a qualified electrician. Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician. a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’. b) Connect the BROWN live wire to the live terminal ‘L’. c) Connect the BLUE neutral wire to the neutral terminal ‘N’. ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight. Sealey recommend that repairs are carried out by a qualified electrician. 1.1.5. only allow the minimal amount of pump cable to enter water or wet areas. the electrical cable is designed for use in water and must not be substituted. If damaged contact a qualified electrician. 1.1.6. extension cable use. only use a cable designed for use with water equipment. contact your stockist or a qualified electrician for advice. Ensure water is kept clear of electrical mains power supply. DO NOt touch switch or plug with wet hands. 1.2. GeNeral saFetY �� � warNiNG! Pump must be used in accordance with Health & safety, government, local authority, and water authority rules and regulations. 9 familiarise yourself with application and limitations, as well as the specific potential hazards peculiar to the pump. �� � warNiNG! disconnect the pump from the mains power before changing accessories, servicing or performing any maintenance. 9� � maintain the pump in good condition (use an authorised service agent). Keep the pump clean. 9� � replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty. 9� � only use for pumping clean cold or warm water (NOt exceeding 35ºc). 9� � if pump is used to pump water from a well, drain or deep receptacle, take adequate precautions to stop persons and animals falling in. 9� � use the built-in handle to lower or raise the pump. it may be necessary to attach a suitable rope or pulley to the handle. 9� � if the bottom of the water container is covered with sludge, sand, gravel or mud etc, suspend the pump or place it on a raised base to operate above the solid matter. sand and such substances will reduce working life of pump, and invalidate your warranty. 9� � in flood situations, user is responsible for ensuring that appropriate back-up procedures, alarms etc are correctly installed in case of pump failure. 9� � in swimming pools, fish ponds, etc, ensure location is clear of people and animals, including removal of fish from pond. Note: this pump is not designed for continuous use in a fish pond or similar water feature or display. 8� � DO NOt operate the pump if any parts are damaged or missing as this may cause failure and/or possible personal injury. 8� � DO NOt use the pump for any purpose other than that for which it is designed. 8� � DO NOt insert hands into the mouth of the pump as this could lead to injury. reCOmmeNDeD Fuse ratiNGs: wpC100.V2/100a.V2: 5amp all OtHer mODels: 13amp Original Language Version WPC100.V2, WPC100A.V2, WPC150.V2, WPC150A.V2, WPC235.V2, WPC235A.V2, WPC250, WPC250A Issue: 3(L) - 25/10/17 © Jack sealey limited

8� � DO NOt operate the pump out of water. the pump pick up area must be completely submerged during operation. 8� � DO NOt exceed the maximum submersible depth (see specifications: max. suction Height). 8 DO NOt operate the pump during freezing temperatures. DO NOt leave the pump in water that may freeze. 8 DO NOt use in swimming pools if people could come into contact with the water whilst pump is in use. 8 DO NOt use for pumping sea water or inflammable, corrosive, explosive or dangerous liquids. 8 DO NOt carry the pump by its electrical cable, or its outlet pipe. use the handle only. 9 When not in use, switch off pump and remove plug from power supply. rinse pump, drain out any water and store in a frost free, safe location. � warNiNG! DO NOt allow uncontrolled discharge of contaminated water which would pollute the environment. note: this appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. children should be supervised to ensure that they do not play with the appliance. 2. iNtrODuCtiON manufactured from corrosion resistant materials with stainless steel motor case and Noryl base cover. Minimum water depth of just 20mm. designed for clean water although these pumps will accept small particles up to 5mm. suitable for the effective drainage of cellars, sinks, cisterns, baths and the general transfer of water. The WPC100A.V2, WPC150A.V2, WPC235A.V2 and WPC250A feature an automatic low water cut-out. 3. speCiFiCatiON 4. OperatiON � warNiNG! ensure you read, understand and apply safety instructions. 4.1. fit appropriate discharge pipe to pump outlet and secure with clip. ensure the diameter of the discharge pipe is the same as or greater than the outlet diameter, as a smaller pipe will adversely effect the pump flow rate. 4.2. Position the pump in the water accordingly, and place the outlet pipe securely in the discharge receptacle or area. it is recommended that the pump is sunk with its discharge outlet facing up, to release any trapped air. 4.3. connect the pump to the electrical mains supply and switch it on. The automatic versions will automatically turn on as the level of water rises (fig.1.A). As the water level lowers, the float will automatically switch the pump off as it reaches the minimum height (fig.1.B). The float may be adjusted by shortening or lengthening the cable. The pump will switch on if the water level is up to or above the maximum length of the float cable. To function correctly the float must move freely. Ensure the float can do so and that the cable is not restricted. Check that the pump and discharge are working correctly. 4.4. the water into which the pump is placed will act as the motor’s cooling agent. for this reason the pump must remain submerged at all times. should the pump have to be used in shallow water, DO NOt operate it for more than 10 minutes. Failure to follow this rule will damage the unit and will invalidate the warranty. NOTE: See fig.2 to determine minimum clearance required if using pump in a restricted area, i.e. a well, etc. 5. maiNteNaNCe � warNiNG! With the exception listed below, all pump, float and electrical cable service maintenance and repair must only be undertaken by an authorised service agent. failure to observe this rule may be dangerous and will invalidate the warranty. � warNiNG! ensure the pump is disconnected from the mains power supply before attempting any service or maintenance. 4.1. Keep all parts of the pump clean. rinse, drain and allow to dry before storing the pump. model No. Cut-Out Outlet OD maximum maximum motor input maximum minimum maximum Output Head particle size water Depth water Depth WPC100.V2 Manual 32mm 100ltr/min 6.0mtr 250W 230V 5mm 20mm 5mtr WPC150.V2 Manual 32mm 167ltr/min 8.0mtr 500W 230V 5mm 20mm 7mtr WPC235.V2 Manual 38mm 208ltr/min 8.5mtr 750W 230V 5mm 20mm 7mtr WPC250 Manual 38mm 250ltr/min 9.5mtr 900W 230V 5mm 20mm 5mtr WPC100A.V2 Automatic 32mm 100ltr/min 6.0mtr 250W 230V 5mm 20mm 5mtr WPC150A.V2 Automatic 32mm 167ltr/min 8.0mtr 500W 230V 5mm 20mm 7mtr WPC235A.V2 Automatic 38mm 208ltr/min 8.5mtr 750W 230V 5mm 20mm 7mtr WPC250A Automatic 38mm 250ltr/min 9.5mtr 900W 230V 5mm 20mm 5mtr fig.1 fig.2 Original Language Version WPC100.V2, WPC100A.V2, WPC150.V2, WPC150A.V2, WPC235.V2, WPC235A.V2, WPC250, WPC250A Issue: 3(L) - 25/10/17 © Jack sealey limited

01284 757500 01284 703534 [email protected] www.sealey.co.uk eNVirONmeNt prOteCtiON recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations. weee reGulatiONs Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information. Note: it is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. important: no liability is accepted for incorrect use of this product. warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. 4.2. regularly check the water inlet on the base of the pump to ensure that there are no blockages. to access the impeller, carefully undo the base hex headed screws and remove the base. clean the impeller and replace the base ensuring that the o ring is correctly located. 8 DO NOt dismantle any other part of the unit. 6. trOublesHOOtiNG a. motor operates but there is no suction. b. reduced water volume for level of water. c. the pump will not start or suddenly stops during operation. 1. no electrical power. 2. float not working. 3. Impeller is jammed. 1. check cable, plug and fuse. 2. contact authorised service agent. 3. clean the pump. 1. discharge pipe bent, or pinched. 2. discharge pipe too narrow. 3. Pump partially blocked. 1. straighten pipe. 2. use wider diameter pipe. 3. clean pump. 1. Water level below min suction depth. 2. Air bubbles in pump accumulated during submersion, or float is incorrectly positioned so pump does not stop at minimum level and sucks in air. 3. clogged intake filter or discharge pipe. 1. stop the pump. 2. release air by inclining the pump and re-immersing it in water. 3. remove blockage, and clean the unit. prOblem Cause sOlutiON Original Language Version WPC100.V2, WPC100A.V2, WPC150.V2, WPC150A.V2, WPC235.V2, WPC235A.V2, WPC250, WPC250A Issue: 3(L) - 25/10/17 © Jack sealey limited

Model/Type: ��������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� Manufacturing Date/Serial Number where applicable: ���������������������������������������������������������������������������������������������������������������������������� This declaration of conformity is issued under the sole responsibility of the manufacturer: Jack Sealey Ltd, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR Declaration of Conformity in accordance with the above Directive(s)� Technical file compiled by: Jack Sealey Ltd Being the responsible person appointed by the manufacturer. Signed ������������������������������������������������������������������������������������������� Date ����������������������������������������������������������������������������������������������� Name ��������������������������������������������������������������������������������������������� Position ����������������������������������������������������������������������������������������� Place: Bury St Edmunds Submersible Water Pump 230V 100ltr/min 167ltr/min 208ltr/min 250ltr/min (A = Automatic) 2014/30/EU EMC Directive 2014/35/EU Low Voltage Directive 2011/65/EU RoHS Directive References to harmonised standard(s) EN 55014-1:2006+A1+A2 ������������������������������������������������������������ EN 55014-2:2015 ������������������������������������������������������������������������� EN 61000-3-2:2014 ���������������������������������������������������������������������� EN 61000-3-3:2013 ���������������������������������������������������������������������� ������������������������������������������������������������������������������������������������������ ������������������������������������������������������������������������������������������������������ EN 60335-1:2012+A11 ����������������������������������������������������������������� EN 60335-2-41:2003+A1+A2 ������������������������������������������������������� EN 62233:2008����������������������������������������������������������������������������� ������������������������������������������������������������������������������������������������������ ������������������������������������������������������������������������������������������������������ ������������������������������������������������������������������������������������������������������ ������������������������������������������������������������������������������������������������������ 4 August 2017 Steve Buckle� Marketing Director� 20172813 Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 [email protected] www.sealey.co.uk WPC100 v2 WPC100A v2 WPC150 v2 WPC150A v2 WPC235 v2 WPC235A v2 WPC250 v1 WPC250A v1

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 [email protected] www.sealey.co.uk Page 1 of 2 NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. Parts Information: Submersible Water Pump 100ltr/min 230V Model No: WPC100.V2

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 [email protected] www.sealey.co.uk Page 2 of 2 NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. Parts Information: Submersible Water Pump 100ltr/min 230V Model No: WPC100.V2 1 WP08701001 POWER CABLE 2 WPC100V2.02 SELF-TAPPING SCREW (4.5x30) 3 WP03802031 WASHER 4 WP00302015 REAR PUMP CASING 5 WP05201033 CABLE SHEATH 6 WPC250.06 CABLE PLUG 7 WP05602005 CABLE BUCKLE 8 WPC100V2.08 CAPACITOR 4uF 9 WP05501001 CABLE GRIP 10 WP07802018 SELF-TAPPING SCREW 11 WP02602004 ALUMINUM REAR COVER 12 WP03801001 WAVE WASHER 13 B/6201ZZ BEARING 6201ZZ 14 WPC100V2.14 ROTOR 15 WPC100V2.15 STATOR 16 WPC250.16 BUSHING 17 WP03802023 WASHER 18 WPC100V2.18 SEAL 19 WP04204001 ALUMINUM BUSHING 20 WPC100V2.20 O-RING 21 WPC100V2.21 FRONT COVER Item Part No. Description 22 WP05101010 O-RING 23 WPC250.23 ADJUSTABLE WASHER 24 WPC100V2.24 IMPELLER 25 WPC100V2.25 NUT 26 WP02901010 MAIN PUMP CASING 27 WPC250.27 O-RING 28 WPC250.28 BASE 29 WP845I SELF TAPPING SCREW ST4.2x32 30 WPC100V2.30 O-RING 31 WPC250.31 ELBOW 32 WPC100V2.32 OUTLET CONNECTOR 33 WPC250.33 FLEXIBLE CONNECTOR 34 WP04105006 GROUND COVER 35 WP04101001 NYLON SAFETY PRESS LINE CAP 36 WP03203012 RUBBER CLIP 37 WP08501001 CABLE TIE 38 WP06101007 MECHANICAL SEAL 39 WPC100V2.39 BLOCK

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 [email protected] www.sealey.co.uk Page 1 of 2 NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. Parts Information: Submersible Water Pump Automatic 100ltr/min 230V Model No: WPC100A.V2

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 [email protected] www.sealey.co.uk Page 2 of 2 NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. Parts Information: Submersible Water Pump Automatic 100ltr/min 230V Model No: WPC100A.V2 1 WP08701001 POWER CABLE 2 WPC100AV2.02 FLOAT SWITCH 3 WPC100V2.02 SELF-TAPPING SCREW (4.5x30) 4 WP03802031 WASHER 5 WP00302015 REAR PUMP CASING -- WPC100V2.04-1 HANDLE COVER (NOT SHOWN) -- WPD235AV2.05B REAR PUMP HOUSING (NOT SHOWN) 6 WP05201036 CABLE SHEATH 6A WP05201033 CABLE SHEATH 7 WP05602008 CABLE BUCKLE 7A WP05602005 CABLE BUCKLE 8 WPC100V2.08 CAPACITOR 4uF 9 WP05501001 CABLE GRIP 10 WP07802018 SELF-TAPPING SCREW 11 WP02602004 ALUMINUM REAR COVER 11.1 WP05202003 WIRE SHEATH 11.2 WPC100V2.11-2 WASHER 11.3 WP08601010 WIRE (GREEN/YELLOW) 11.4 WP04102006 PLATE 11.5 WPC100V2.11-5 WASHER 11.6 WP818 SCREW M4X8 12 WP03801001 WAVE WASHER 13 B/6201ZZ BEARING 6201ZZ 14 WPC100V2.14 ROTOR 15 WPC100V2.15 STATOR 16 WPC250.16 BUSHING 17 WP03802023 WASHER Item Part No. Description 18 WPC100V2.18 SEAL 19 WP04204001 ALUMINUM BUSHING 20 WPC100V2.20 O-RING 21 WPC100V2.21 FRONT COVER 22 WP05101010 O-RING 23 WPC250.23 ADJUSTABLE WASHER -- WPC250.23-1 ADJUSTABLE WASHER (NOT SHOWN) 24 WPC100V2.24 IMPELLER 25 WPC100V2.25 NUT 26 WP02901010 MAIN PUMP CASING -- WP3086 STEEL BALL (NOT SHOWN) 27 WPC250.27 O-RING 28 WPC250.28 BASE 29 WP845I SELF TAPPING SCREW ST4.2x32 30 WPC100V2.30 O-RING 31 WPC250.31 ELBOW 32 WPC100V2.32 OUTLET CONNECTOR 33 WPC250.33 FLEXIBLE CONNECTOR 34 WP04105006 GROUND COVER 35 WP04101001 NYLON SAFETY PRESS LINE CAP -- WP04101003 NYLON SAFETY PRESS LINE CAP (NOT SHOWN) 36 WPC100V2.36 RUBBER CLIP 37 WP08501001 CABLE TIE 38 WP06101007 MECHANICAL SEAL 39 WPC100V2.39 BLOCK

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 [email protected] www.sealey.co.uk Page 1 of 2 NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. Parts Information: Submersible Water Pump 167ltr/min 230V Model No: WPC150.V2

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 [email protected] www.sealey.co.uk Page 2 of 2 NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. Parts Information: Submersible Water Pump 167ltr/min 230V Model No: WPC150.V2 1 WP08701001 POWER CABLE 2 WPC150V2.02 SELF-TAPPING SCREW (4.5x30) 3 WP03802031 WASHER 4 WP00302015 REAR PUMP CASING -- WPC150V2.04-1 HANDLE COVER (NOT SHOWN) -- WPD235AV2.05B REAR PUMP HOUSING (NOT SHOWN) 5 WP05201033 CABLE SHEATH 6 WPC250.06 CABLE PLUG 7 WP05602005 CABLE BUCKLE 8 WPC150V2.08 CAPACITOR 8uF 9 WP05501001 CABLE GRIP 10 WP07802018 SELF-TAPPING SCREW 11 WP02602004 ALUMINUM REAR COVER 11.1 WP05202003 WIRE SHEATH 11.2 WPC150V2.11-2 WASHER 11.3 WP08601010 WIRE (GREEN/YELLOW) 11.4 WP04102006 PLATE 11.5 WPC150V2.11-5 WASHER 11.6 WP818 SCREW M4X8 12 WP03801001 WAVE WASHER 13 B/6201ZZ BEARING 6201ZZ 14 WPC150V2.14 ROTOR 15 WPC150V2.15 STATOR 16 WPC235V2.16 BUSHING 17 WP03802023 WASHER 18 WPC150V2.18 SEAL Item Part No. Description 19 WP04204001 ALUMINUM BUSHING 20 WPC150V2.20 O-RING 21 WPC150V2.21 FRONT COVER 22 WP05101010 O-RING 23 WPC250.23 ADJUSTABLE WASHER -- WPC250.23-1 ADJUSTABLE WASHER (NOT SHOWN) 24 WPC150V2.24 IMPELLER 25 WPC150V2.25 NUT 26 WP02901010 MAIN PUMP CASING 26.1 WP3086 STEEL BALL 27 WPC250.27 O-RING 28 WPC250.28 BASE 29 WP845I SELF TAPPING SCREW ST4.2x32 30 WPC150V2.30 O-RING 31 WPC250.31 ELBOW 32 WPC250.32 OUTLET CONNECTOR 33 WPC250.33 FLEXIBLE CONNECTOR 34 WP04105006 GROUND COVER 35 WP04101001 NYLON SAFETY PRESS LINE CAP 35.1 WP04101003 NYLON SAFETY PRESS LINE CAP 36 WP03203012 RUBBER CLIP 37 WP08501001 CABLE TIE 38 WP06101007 MECHANICAL SEAL 39 WPC150V2.39 BLOCK

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 [email protected] www.sealey.co.uk Page 1 of 2 NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. Parts Information: Submersible Water Pump Automatic 167ltr/ min 230V Model No: WPC150A.V2

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 [email protected] www.sealey.co.uk Page 2 of 2 NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. Parts Information: Submersible Water Pump Automatic 167ltr/ min 230V Model No: WPC150A.V2 1 WP08701001 POWER CABLE 2 WPC150AV2.02 FLOAT SWITCH 3 WPC150V2.02 SELF-TAPPING SCREW (4.5x30) 4 WP03802031 WASHER 5 WP00302015 REAR PUMP CASING -- WPC150V2.04-1 HANDLE COVER (NOT SHOWN) -- WPD235AV2.05B REAR PUMP HOUSING (NOT SHOWN) 6 WP05201036 CABLE SHEATH 6A WP05201033 CABLE SHEATH 7 WP05602008 CABLE PRESS PAD 7A WP05602005 CABLE PRESS PAD 8 WPC150V2.08 CAPACITOR 8uF 9 WP05501001 CABLE GRIP 10 WP07802018 SELF-TAPPING SCREW 11 WP02602004 COVER 11.1 WP05202003 CABLE SHEATH 11.2 WPC150V2.11-2 WASHER 11.3 WP08601010 YELLOW/GREEN WIRE 11.4 WP04102006 WIRE CONNECTING PAD 11.5 WPC150V2.11-5 WASHER 11.6 WP818 SCREW M4X8 12 WP03801001 WAVE WASHER 13 B/6201ZZ BEARING 6201ZZ 14 WPC150V2.14 ROTOR 15 WPC150V2.15 STATOR 16 WPC235V2.16 BUSHING 17 WP03802023 WASHER Item Part No. Description 18 WPC150V2.18 SEAL 19 WP04204001 ALUMINUM BUSHING 20 WPC150V2.20 O-RING 21 WPC150V2.21 FRONT COVER 22 WP05101010 O-RING 23 WPC250.23 ADJUSTABLE WASHER -- WPC250.23-1 ADJUSTABLE WASHER (NOT SHOWN) 24 WPC150V2.24 IMPELLER 25 WPC150V2.25 NUT 26 WP02901010 MAIN PUMP CASING -- WP3086 STEEL BALL (NOT SHOWN) 27 WPC250.27 O-RING 28 WPC250.28 BASE 29 WP845I SELF TAPPING SCREW ST4.2x32 30 WPC150V2.30 O-RING 31 WPC250.31 ELBOW 32 WPC250.32 OUTLET CONNECTOR 33 WPC250.33 FLEXIBLE CONNECTOR 34 WP04105006 GROUND COVER 35 WP04101001 NYLON SAFETY PRESS LINE CAP -- WP04101003 NYLON SAFETY PRESS LINE CAP (NOT SHOWN) 36 WP03203012 RUBBER CLIP 37 WP08501001 CABLE TIE 38 WP06101007 MECHANICAL SEAL 39 WPC150V2.39 BLOCK

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 [email protected] www.sealey.co.uk Page 1 of 2 NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. Parts Information: Submersible Water Pump 208ltr/min 230V Model No: WPC235.V2

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 [email protected] www.sealey.co.uk Page 2 of 2 NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. Parts Information: Submersible Water Pump 208ltr/min 230V Model No: WPC235.V2 1 WP08701001 POWER CABLE 2 WPC235V2.02 SELF-TAPPING SCREW (4.5x30) 3 WP03802031 WASHER 4 WPC235V2.04 REAR PUMP HOUSING -- WPC250.04-1 HANDLE COVER (NOT SHOWN) -- WPD235AV2.05B REAR PUMP HOUSING (NOT SHOWN) 5 WPC235V2.05 CABLE SHEATH 6 WPC250.06 CABLE PLUG 7 WP05602005 CABLE BUCKLE 8 WPC235V2.08 CAPACITOR 8uF 9 WP05501001 CABLE GRIP 10 WP07802018 SELF-TAPPING SCREW 11 WP02602004 ALUMINUM REAR COVER 11.1 WP05202003 WIRE SHEATH 11.2 WPC235V2.11-2 WASHER 11.3 WP08601010 WIRE (GREEN/YELLOW) 11.4 WP04102006 PLATE 11.5 WPC235V2.11-5 WASHER 11.5 WP818 SCREW M4X8 12 WP03801001 WAVE WASHER 13 B/6201ZZ BEARING 6201ZZ 14 WPC235V2.14 ROTOR 15 WPC235V2.15 STATOR 16 WPC235V2.16 BUSHING 17 WP03802023 WASHER 18 WPC235V2.18 SEAL Item Part No. Description 19 WP04204001 ALUMINUM BUSHING 20 WPC235V2.20 O-RING 21 WPC235V2.21 FRONT COVER 22 WP05101010 O-RING 23 WPC250.23 ADJUSTABLE WASHER -- WPC235V2.23 ADJUSTABLE WASHER (NOT SHOWN) 24 WPC235V2.24 IMPELLER 25 WPC235V2.25 NUT 26 WPC235V2.26 PUMP BODY 26.1 WP3086 STEEL BALL 27 WPC250.27 O-RING 28 WPC250.28 BASE 29 WP845I SELF TAPPING SCREW ST4.2x32 30 WPC235V2.30 O-RING 31 WPC250.31 ELBOW 33 WPC250.32 OUTLET CONNECTOR 33 WPC250.33 FLEXIBLE CONNECTOR 34 WP04105006 GROUND COVER 35 WP04101001 NYLON SAFETY PRESS LINE CAP -- WP04101003 NYLON SAFETY PRESS LINE CAP (NOT SHOWN) 36 WP03203012 RUBBER CLIP 37 WP08501001 CABLE TIE 38 WP06101007 MECHANICAL SEAL 39 WPC235V2.39 BLOCK

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 [email protected] www.sealey.co.uk Page 1 of 2 NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. Parts Information: Submersible Water Pump Automatic 208ltr/min 230V Model No: WPC235A.V2

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 [email protected] www.sealey.co.uk Page 2 of 2 NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. Parts Information: Submersible Water Pump Automatic 208ltr/min 230V Model No: WPC235A.V2 1 WP08701001 POWER CABLE 2 WPC235AV2.02 FLOAT SWITCH 3 WPC235V2.02 SELF-TAPPING SCREW (4.5x30) 4 WP03802031 WASHER 5 WPC235V2.04 REAR PUMP HOUSING -- WPC250.04-1 HANDLE COVER (NOT SHOWN) -- WPD235AV2.05B REAR PUMP HOUSING (NOT SHOWN) 6 WPC235V2.05 CABLE SHEATH 6A WP05201036 CABLE SHEATH 7 WP05602008 PAD 7A WP05602005 CABLE PRESS PAD 8 WPC235V2.08 CAPACITOR 8uF 9 WP05501001 CABLE GRIP 10 WP07802018 SELF-TAPPING SCREW 11 WP02602004 ALUMINUM REAR COVER 11.1 WP05202003 WIRE SHEATH 11.2 WPC235V2.11-2 WASHER 11.3 WP08601010 YELLOW/GREEN WIRE 11.4 WP04102006 WIRE CONNECTING PAD 11.5 WPC235V2.11-5 WASHER 11.6 WP818 SCREW M4X8 12 WP03801001 WAVE WASHER 13 B/6201ZZ BEARING 6201ZZ 14 WPC235V2.14 ROTOR 15 WPC235V2.15 STATOR 16 WPC235V2.16 BUSHING 17 WP03802023 WASHER Item Part No. Description 18 WPC235V2.18 SEAL 19 WP04204001 ALUMINUM BUSHING 20 WPC235V2.20 O-RING 21 WPC235V2.21 FRONT COVER 22 WP05101010 O-RING 23 WPC250.23 ADJUSTABLE WASHER -- WPC250.23-1 ADJUSTABLE WASHER (NOT SHOWN) 24 WPC235V2.24 IMPELLER 25 WPC235V2.25 NUT 26 WPC235V2.26 PUMP BODY -- WP3086 STEEL BALL (NOT SHOWN) 27 WPC250.27 O-RING 28 WPC250.28 BASE 29 WP845I SELF TAPPING SCREW ST4.2x32 30 WPC235V2.30 O-RING 31 WPC250.31 ELBOW 32 WPC250.32 OUTLET CONNECTOR 33 WPC250.33 FLEXIBLE CONNECTOR 34 WP04105006 GROUND COVER 35 WP04101001 NYLON SAFETY PRESS LINE CAP -- WP04101003 NYLON SAFETY PRESS LINE CAP (NOT SHOWN) 36 WP03203012 RUBBER CLIP 37 WP08501001 CABLE TIE 38 WP06101007 MECHANICAL SEAL 39 WPC235V2.39 BLOCK

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 [email protected] www.sealey.co.uk Page 1 of 2 NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. Parts Information: Submersible Water Pump 250ltr/min 230V Model No: WPC250

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 [email protected] www.sealey.co.uk Page 2 of 2 NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. Parts Information: Submersible Water Pump 250ltr/min 230V Model No: WPC250 1 WP08701001 POWER CABLE 2 WPC250.02 RD HEAD S/T SCREW M4X22 3 FWM4.S FLAT WASHER M4 SINGLE 4 WPC250.04 REAR PUMP HOUSING -- WPC250.04-1 HANDLE COVER (NOT SHOWN) -- WPD235AV2.05B REAR PUMP HOUSING (NOT SHOWN) 5 WP05201036 CABLE SHEATH 6 WPC250.06 CABLE PLUG 7 WP05602008 CABLE BUCKLE 8 WPC250.08 CAPACITOR 16uF 9 WP05501001 CABLE GRIP 10 WP07802018 SELF-TAPPING SCREW 11 WP02602004 ALUMINUM REAR COVER 11.1 WP05202003 WIRE SHEATH 11.2 WPC250.11-2 WASHER 11.3 WP08601010 WIRE 11.4 WP04102006 PLATE 11.5 WPC250.11-5 WASHER 11.6 WP818 SCREW M4X8 12 WP03801001 WAVE WASHER 13 B/6201ZZ BEARING 6201ZZ 14 WPC250.14 ROTOR 15 WPC250.15 STATOR 16 WPC250.16 BUSHING 17 WP03802023 WASHER 18 WPC250.18 SEAL Item Part No. Description 19 WP04204001 ALUMINUM BUSHING 20 WPC250.20 O-RING 21 WPC250.21 FRONT COVER 22 WPC250.22 O-RING 23 WPC250.23 ADJUSTABLE WASHER -- WPC250.23-1 ADJUSTABLE WASHER (NOT SHOWN) 24 WPC250.24 IMPELLER 25 NLN8.S NYLOC NUT M8 ZINC DIN 985 (SINGLE) 26 WPC250.26 PUMP BODY 26.1 WP3086 STEEL BALL 27 WPC250.27 O-RING 28 WPC250.28 BASE 29 WPC100.V2-16 RD HEAD S/T SCREW M4X30 30 WPC250.30 O-RING 31 WPC250.31 ELBOW 32 WPC250.32 OUTLET CONNECTOR 33 WPC250.33 FLEXIBLE CONNECTOR 34 WP04105006 GROUND COVER 35 WP04101001 NYLON SAFETY PRESS LINE CAP -- WP04101003 NYLON SAFETY PRESS LINE CAP (NOT SHOWN) 36 WP03203012 RUBBER CLIP 37 WP08501001 CABLE TIE 38 WP06101007 MECHANICAL SEAL 39 WPC250.39 BLOCK

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 [email protected] www.sealey.co.uk Page 1 of 2 NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. Parts Information: Submersible Water Pump Automatic 250ltr/min 230V Model No: WPC250A

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 [email protected] www.sealey.co.uk Page 2 of 2 NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. Parts Information: Submersible Water Pump Automatic 250ltr/min 230V Model No: WPC250A 1 WP08701001 POWER CABLE 2 WPC250A.02 FLOAT SWITCH 3 WPC250.02 RD HEAD S/T SCREW M4X22 4 FWM4.S FLAT WASHER M4 SINGLE 5 WPC250.04 REAR PUMP HOUSING -- WPC250.04-1 HANDLE COVER (NOT SHOWN) -- WPD235AV2.05B REAR PUMP HOUSING (NOT SHOWN) 6 WP05201036 CABLE SHEATH 7 WP05602008 CABLE BUCKLE 8 WPC250.08 CAPACITOR 16uF 9 WP05501001 CABLE GRIP 10 WP07802018 SELF-TAPPING SCREW 11 WP02602004 ALUMINUM REAR COVER 11.1 WP05202003 WIRE SHEATH 11.2 WPC250.11-2 WASHER 11.3 WP08601010 WIRE 11.4 WP04102006 PLATE 11.5 WPC250.11-5 WASHER 11.6 WP818 SCREW M4X8 12 WP03801001 WAVE WASHER 13 B/6201ZZ BEARING 6201ZZ 14 WPC250.14 ROTOR 15 WPC250.15 STATOR 16 WPC250.16 BUSHING 17 WP03802023 WASHER 18 WPC250.18 SEAL Item Part No. Description 19 WP04204001 ALUMINUM BUSHING 20 WPC250.20 O-RING 21 WPC250.21 FRONT COVER 22 WPC250.22 O-RING 23 WPC250.23 ADJUSTABLE WASHER -- WPC250.23-1 ADJUSTABLE WASHER (NOT SHOWN) 24 WPC250.24 IMPELLER 25 NLN8.S NYLOC NUT M8 ZINC DIN 985 (SINGLE) 26 WPC250.26 PUMP BODY -- WP3086 STEEL BALL (NOT SHOWN) 27 WPC250.27 O-RING 28 WPC250.28 BASE 29 WPC100.V2-16 RD HEAD S/T SCREW M4X30 30 WPC250.30 O-RING 31 WPC250.31 ELBOW 32 WPC250.32 OUTLET CONNECTOR 33 WPC250.33 FLEXIBLE CONNECTOR 34 WP04105006 GROUND COVER 35 WP04101001 NYLON SAFETY PRESS LINE CAP -- WP04101003 NYLON SAFETY PRESS LINE CAP (NOT SHOWN) 36 WP03203012 RUBBER CLIP 37 WP08501001 CABLE TIE 38 WP06101007 MECHANICAL SEAL 39 WPC250.39 BLOCK