Pixel TW-282 Product Manual

TW-282 中国制造 Http://www.pixelhk.com.cn

Overview 03 TW-282 introduction 05 The name of each part 06 09 Prepare for install and use Fix the receiver(TW-282RX) 1 1 Channel Setting 13 1 Open the background light of display 1 4 Install and replace the battery 09 Cautions 04 Receiver connected with the camera 1 5 Shooting control 1 6 Single shooting 1 6 Continuous shooting within one sec 17 Contents

Delay shooting 2 0 Timing plan for shooting 23 This manual is current update of 1st Jan, 2011. Please contact to PIXEL distributor for further information, if interesting of the combining usage with products released after this day. Overview Thank you for purchasing high-performance PIXEL products First of all, thank you for purchasing product of Wireless Timer Remote Control TW-282. The shooting ways included single shooting, continuous shooting within one sec, BULB shooting, user-defined time-delay and timing plan for shooting. Low consumption of LCD display will make you be clear at a glance of the using status and using plan. Before use this product, you must read and fully understand this manual, then learn to use the camera to ensure you are familiar with the operation properly. Through this manual you can easily handle the operation method and the attentive things.

corrosive liquids, heat or explosion. Make sure the camera and receiver (TW-282RX) are powered off before install it. When connected the remote cable with the device, do not pull the wires. As this is an electronic product accessory; some of the environment causes may affect the working. However this is hardly ever to get this situation. This product can't be strong vibration, or may lead to product failure. For a long time non-use, please remove the battery to prevent leakage of corrosive liquids and damage the product. Do not put it in high temperature, such as a closed car under direct sunlight, the control panel and other high-temperature areas. Keep dry, don’t use wet hand contact with the product, it must not be immersed in water or exposed to rain, and this may lead to not work properly. Do not use flammable and explosive gases in violation of this warning may cause an explosion or fire. Because this product include battery, regarding how to use battery, please operate it strictly according to related rules, otherwise it may cause explosion, fire or physical injury. 3 Cautions Using the wireless remote control technology to achieve shutter’s external socket with camera for remote control . FSK 2.4GHz wireless controls system, which more reliability and stability, 15 channels available. Operating distance range up to 80M or above. LCD display is showing channel, power, function mode, it's easy to understand and operate. Ultra-low power standby, transmitter (TW-282TX) uses 2pcs AAA batteries, which standby time over four years; the receiver (TW-282RX) uses 3V CR-2 lithium battery, which more than 400 hours of standby time. Different shutter connect cable can be connect with different brand cameras. It can control multiple cameras simultaneously. The camera can be user-defined delay and timing plan shooting. Set the parameters for timing shooting. single shooting, continuous shooting within one sec, BULB shooting and

Receiver (TW-282RX) Channel display screen Power button/channel reduce button Background light button/ channel increase button Battery hatch 6 7 9 10 9 10 11 Battery compartment Hot shoe fixed nut Quick release plate holding nut Hot shoe fixed mount Output control signal interface 8 Please check all included items after open the packing, if missing, please contact the dealer. 1. Transmitter (TW-282TX) ------- 1pc 3. Shutter connect cable ---------- 1pc 4. Manual(this manual) ------------ 1pc The name of each part Here are the names of each part: 2. Receiver (TW-282RX) ---------- 1pc The name of each part 10 Indicator light Indicator light 9 Display 8 Timing plan start/stop button 7 Increment button 6 Right move button 5 Setting/Enter button 4 Release button 3 Decrement button 2 Left move button 1 Background light button 11 Battery hatch 12 Product back sticker 13 Item code 11 1 3 2 4 5 12 13 9 5 6 7 8 1 2 3 4 11 10

12 The icon of timing shots The icon of interval time 11 10 The icon of exposure time The icon of delay time 9 8 Low battery voltage icon 7 Delay shooting icon 6 shooting icon 4 Single shooting icon Function area 3 Display of transmitter Input plug Shutter connect plug Shutter connect cable Display of transmitter 1 2 1 Timing plan function area 2 Time display area 5 Continuous shooting within one sec icon The icon of channel 13 Preparation for installation and use Install and replace the battery Before use, you should read the user manual of your camera carefully and well understand the manipulation and functional setting. The function setting of camera may influence this item’s efficiency control of the camera. The low battery voltage icon[ ]will twinkle or the character become dim obvious when the power is not enough, that means the low battery voltage has already influence the normal work of the device, which needs to replace the battery in time. The transmitter uses 2pcs AAA batteries; Please follow the steps to replace the battery if needed. 1. Slide and open the battery hatch. DC0 DC1 DC2 E3 N3 L1 S1 UC1 1 2 CB1 CL- CL- CL- CL- CL- CL- CL- CL- CL-

The receiver(TW-282RX) 3. Close the battery hatch. 3. Close the battery hatch. 2. Follow the signs of positive [ + ] and negative [ - ] in the battery compartment to install the battery correctly. You should pay attention to the polarity of battery because of the wrong installation will make the device work abnormally, or even physical injury. You should pay attention to the polarity of battery because of the wrong installation will make the device work abnormally, or even physical injury. The low battery voltage icon[ ]will twinkle when the power is not enough, that means the low battery voltage has already influenced the normal work of the device, which needs to replace the battery in time. The receiver uses CR-2 lithium battery; Please follow the steps to replace the battery if needed. 1. Slide and open the battery hatch. 2. the signs of positive [+] and negative [-] in the battery compartment to install the battery correctly. Follow Preparation for installation and use Preparation for installation and use Receiver can be fixed on the top of camera, rack of camera accessory or tripod. Fix the receiver on the hot shoe of camera. Fix on the rack of camera accessory. the receiver Fix on the tripod. the receiver Loosen hot shoe fixed nut when you remove . forcibly pull it, in order to avoid damage to the receiver and camera. the receiver Do not Lock hot shoe fixed nut tightly when you fix it. Make sure to fix firmly so that it will not slide. the receiver 1. Fix the Receiver on the quick release plate through bottom nut. 2. Attach the quick release plate on the tripod. TW-282RX

move the functional icon to the channel icon[ ].Press Setting/Enter button to change the channel, you will see the channel number is flashing. Thought pressing increment button[ ]or decrement button[ ] to adjust the channel number. 4. Press Setting/Enter button again to save the present channel. 13 12 Turned on/off the power Channel setting Channel setting for transmitter(TW-282TX) Preparation for installation and use Preparation for installation and use The transmitter(TW-282TX) Press any button once, and turn on the power of transmitter. The transmitter stays in the single shooting mode when you turn on the power; timing plan and channel setting will not be changed. The display shows the single shooting icon and communication channel. The transmitter without any operation (except timing plan or implementing BULB status) will shut down automatically after one minute. The receiver(TW-282RX) 1. Hold the power button for 2sec to turn on the POWER Green LED light will be flash every 2sec and the screen displays communication channel. 2. After turn on the power, the set timing communication channel remain effectively. 3. The receiver does not turn off automatically. In the power- on state, press power button 2s and the receiver will be turned off. [ ] Channel setting for receiver(TW-282RX) Turn on the power; the channel is default as the last time setting. Press [+CH] and [CH-] button enter to channel setting, the channel icon [CH] on the screen will be flashing. [+CH] is increase the numbe, [CH-] is reduces the number. ress [+CH] and [CH-] button at same time, or no-action for 10 second, can save and exit. P 2s * The channel of transmitter and receiver should be the same for shooting effectively. 1. 2. 3. 4. 1. 2. 3. 1. 2. 3. 4.

Preparation for installation and use Preparation for installation and use Press and hold the background light button for 2 seconds, the background light will be turned on. Open the background light of the receiver and press the button twice each 6 seconds, the background light will keep lit. The background light will not be close by hand; it will turn off after 6 seconds automatically without any operation. Press and hold the background light button for 2 seconds, the background light will be turned on. Open the background light and press the button twice each 6 seconds, the background light will keep lit. The background light will not be close by hand; it will turn off after 6 seconds automatically without any operation. The transmitter(TW-282TX) The receiver(TW-282RX) 2s 2s Receiver connected with the camera Make sure your receiver has been installed in place and to ensure that cameras and receivers are shut down. First, insert the input plug of the shutter connect cable into the receiver's output control signal socket in place. The timer remote control will not be able to control the camera if the shutter connect cable didn’t insert correctly. Fix the camera on the tripod or other fixed frame. protective cover of external shutter socket and put the shutter plug of shutter connect cable in place, then make sure it has been fixed firmly. Open the For most of camera shutter socket, there is a mis-plug interface, please note insert direction so as to avoid damage to shutter socket. Turn on the receiver's power and then the camera's power. 1. 2. 3. 4.

shooting function Single shooting function Press Press Press Press Press Press Continuous shooting within one sec function Delay shooting function The instruction is under the premise that the receiver and camera have been connected tightly, and turned on the power of camera and receiver. The detail instruction of remote shooting will be showing as follow. Single shooting 1. In the power-on state, set the single shooting icon [ ] by pressing the move button[ ]or right move button[ ]. left In the sleeping state, press any key to wake up transmitter to enter single shooting mode. 2. Half-press the release button and transmitter will send signal for focusing, the green indicator will lit on the transmitter and receiver, and the camera is in the focusing state until the release or full-press the button. 3. Full-press the release button and transmitter will send signal of shooting. The red indicator will light for a while, the camera start shooting. Make sure to set the camera function to be [ ]. When the camera function is set to be[ ], it may cause continuous shooting. [ ], . When the camera function is set to be [ ], the camera will execute delay shooting. It will be shooting every sec if camera is set as BULB it may cause the problem of under or over exposure. Continuous shooting within one sec 1. In the power-on state, move the transmitter’s activities icon to continuous shooting within one sec icon[ ] by pressing the left move button[ ]or right move button[ ]. Continuous shooting within one sec second is patent function which issued by Pixel limited Enterprise, it'll support spacing continuous shooting within one sec and never change the single shooting mode. the firs Shooting control

signal for focusing, the green indicator will lit on the transmitter and receiver, and the camera is in the focusing state until the release or full-press the button. 3. Full-press the release button, red indicators of the transmitter and receiver will be lit, keep fully press the button, the transmitter will send signal of shooting continuously, the indicators will blink red and green light in turn. The camera will start to shot, and the shooting speed will be one photo per sec. 4. Release the release button, the transmitter stop sending signal for shooting and the camera will stop shooting. Make sure to set the camera function to be [ ]. When the camera function is set to be [ ], it may cause continuous shooting. [ It will be shooting every sec if camera is set as BULB], it may cause the problem of under or over exposure. When the camera function is set to be[ ], the camera will execute delay shooting. shooting 1. In the power-on state, move the transmitter's activities icon to shooting icon[ ] by pressing the left move button [ ]or right move button[ ]. 2.Half-press the release button and transmitter will send signal for focusing, the green indicator will lit on the transmitter and receiver, and the camera is in the focusing state until the release or full-press the button. 3.Full-press the release button, transmitter will send signal. The red indicator of transmitter starts flashing and start timing, the indicator of receiver will keep lighting. The transmitter continuous output shooting signal. Camera enters into exposure shooting continuously. BULB 4. Press the release button again, the transmitter stop sending out the shooting signal and the time also stopped on screen displays. BULB Make sure to set the camera function to be [ ]. When the camera function is set to be [ ], the camera only shoot once but not BULB shooting. When the camera function is set to be [ ],the camera will be continuous shooting. When the camera function is set to be [ ], the camera will be delay shooting once.

The delay shooting function of TW-282 can user-defined the delay time and shots. 1. In the power-on state, move the transmitter’s activities icon to delay shooting icon[ ] by pressing the move button[ ]or right move button[ ]. Press the set button entering the delay setting for adjusts the shooting numbers. The delay shooting icon[ ],number of shooting [ ]will blink at the same time. left 2. Press button[ ]settings shot number can be increased, press button [ ], settings shot number can be reduced. It can be set between 1 to 99 sheets . 3. Press button[ ]enter into the delay setting of delay shooting. delay shooting time value[ ]will blink at the same time. the delay shooting icon[ ] , 4. Press the button[ ], set the delay time increased, press button[ ], set the delay time reduced. It can be set between 1 to 59 seconds. 21 5. After set up the new parameters, press the set button, save and exit settings. When enter to the delay shooting set, the transmitter will save the previous setting. By pressing the left button[ ]or right button[ ], convert shooting numbers and delay time settings. Gently press button[ ]once to set numerical increased, hold it on, set the value rapidly increased; Press the button[ ]once to set the numerical reduced, hold on to set the values rapidly reduced. Operate the delay shooting Press the left button[ ]or right button[ ], move the transmitter’s activity icon to the delay shooting icon[ ]. Half-press the release button and transmitter will send signal for focusing, the green indicator will lit on the transmitter and receiver, and the camera is in the focusing state until the release or full-press the button. Full-press the release button, transmitter will send all the delay shooting information to receiver, the transmitter starts to delay countdown, and red indicator blink quickly and enter to the delay shooting mode. 1. 2. 3.

will follow the setting shots output a signal per second to control shooting. receiver When the camera function is set to be [ ], the camera will perform one or more delay shooting. When the camera lens focus function is set to be [ M ],the camera will not execute focusing action if half-press the release button of the transmitter. Make sure to set the camera function to be [ ]. When the camera function is set to be [ ], it will start continuous shooting. [ It will be shooting every sec if camera is set as BULB], it may cause the problem of under or over exposure. When the camera lens focus function is set to be [ AF ], even receiving the shooting signal the camera will not shoot at the moment as most of camera don't seize focus. 3. By pressing button[ ]or[ ],enter into the setting for minutes and hours , as the sketch map. “ ” “ ” Timing plan for shooting Delay time setting 1. In the power-on state, move the functional activities icon to the delay timing program icon[ ]by pressing the left move button[ ]or right move button[ ]. 2. Press the set button, enter the delay time for ‘second bit’ setting. Press Press Press Press Press Press Press Press The shot number of timing plan setting Exposu -re time of timing plan setting Delay time of timing plan--hours setting Delay time of timing plan--minutes setting Delay time of timing plan--seconds setting Gently press button[ ]once to set numerical increased, hold it on, set the value rapidly increased; Press the button[ ]once to set the numerical reduced, hold on to set the values rapidly reduced. 4. Press the set button, save and exit settings. 5、 Before delay time planning completed, press either transmitter button or receiver button or other , will terminate this planning.

1. Press left move button[ ]or right move button[ ], move the transmitter’s activities icon to the exposure timing program icon[ ]. 2. Press the set button, enter the delay time for ‘second bit’ setting. 3. By pressing button[ ]or[ ],enter into the setting for minutes and hours , as the sketch map. “ ” “ ” Press Press Press Press Press Press Press Press Exposure time of timing plan--hours setting Exposure plan--minutes setting time of timing Exposure plan--seconds setting time of timing Delay time of timing plan setting Interval time of timing plan setting Gently press button[ ]once to set numerical increased, hold it on, set the value rapidly increased; Press the button[ ]once to set the numerical reduced, hold on to set the values rapidly reduced. 4. Press the set button, save and exit settings. Interval time setting 1. Press left move button[ ]or right move button[ ], move the transmitter’s activities icon to the interval timing program icon[ ]. 2. Press the set button, enter the time for second bit setting. interval “ ” 3. By pressing button[ ]or[ ],enter into the setting for minutes and hours , as the sketch map. “ ” “ ” Press Press Press Press Press Press Press Press Interval time of timing plan--hours setting Interval plan--minutes setting time of timing Interval plan--second setting time of timing Exposu -re time of timing plan setting The shot number of timing plan setting Gently press button[ ]once to set numerical increased, hold it on, set the value rapidly increased; Press the button[ ]once to set the numerical reduced, hold on to set the values rapidly reduced. 4. Press the set button, save and exit settings.

move the transmitter’s activities icon to the icon of timing shots [ ]. 27 26 Shooting control Shooting control The shot number setting 2. Press the setting button enter to set the number of photo in timing plan's, Press [ ] to increase the photo number; Press [ ] to reduce the photo number. 1-99photo number is available, when the screen display means this is unlimited to take the photo. [ -- ] 3. By pressing button[ ]or[ ],enter into the setting for “ exposure time” and “ delay time” , “interval time” as the shown picture. Press Press Press Press Interval time of timing plan setting Delay time of timing plan setting 4. Press the set button, save and exit settings. Search the timing plan 1. Press left move button[ ]or right move button[ ],move transmitter’s activities icon to timing plan icon which can check the related timing project. 2. When check the related projects, if need adjust the parameters, only press the set button to enter the relevant project settings, press the set button again to exit and save your setting. Move the icons sequence showed as below. Press Press Press Press Press Press Press Press Press Press Delay shoot -ing function Singl e shoot -ing func tion Execute timing plan 1. Press the left move button[ ]or right move button[ ], move the activities icon to any icon among the timing plan shooting area. Delay time Exposure time Interval time Number of photo 2. Press the timer plan start/stop button transmitter sends the information to receiver. The green light of receiver will be flash twice every 2 sec; that's mean the receiver is [ ]; completely to receive information and start operate correctly. Timing plan will be working in the receiver and send the control signal to the camera.

completely, the transmitter and receiver will stop regularly scheduled executing. 29 28 Shooting control The following examples illustrate the timing plan running: delay time[ ] = 5 seconds, exposure time[ ] = 1 second, shooting interval[ ]= 6 seconds, shooting number[ ] = 3. Focusing output Shooting output When the timing plan is running on the receiver, press any button of receiver to stop the operation. 3.Transmitter's screen will display the running conditions of timing plan, but it will not send any command to the receiver. This is only showing the receiver running conditions and for reference only. Type : FSK 2.4 GHz wireless control system Transmission distance: 80 meters or above Channel: 15 channels Standby time: Transmitter : more than 4 years(using two 1.5V AAA batteries) Receiver 400 hours (using CR-2 lithium battery) Dimensions (W × H × D) Transmitter: Receiver: Weight with ba ttery Transmitte: Receiver: : : 149 ×49.5 ×24 63mm×38mm×31mm ( )： 70.5g 39.5 g mm mm mm TW-282 Specification Now you can start to use unique high-performance TW-282. If you have any questions, you can contact the local distributor. Or visit the website http://www.pixelhk.com. Wireless Timer Remote Control 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 N=1 N=2 N=3

安装更换电池 09 注意事项 04 接收器与相机的连接 15 拍摄控制 16 单张拍摄 17 1秒连拍 18 目 录

感谢您购买高性能的品色产品 3 2 首先，非常感谢您购买高性能的无线定时器TW-282， 它拥有简易的单张拍 摄、1秒连拍、B门拍摄、延时拍摄以及定时计划拍摄。低功耗的液晶显示屏，能 让您的使用计划一目了然，更方便地使用延时拍摄及定时计划拍摄。 在使用前，您一定要通读并完全理解本使用说明书以及了解相机的使用方 法，以保证您熟悉操作，并且能正确使用。您可以通过本说明书而轻松掌握本产 品的使用方法及注意事项。 总述 拍摄 19 延时拍摄 20 TW-282 规格 29 定时计划拍摄 23

安装电池时极性切勿弄反，否则电池可能渗漏腐蚀性液体、发热或爆炸。 在安装接收器(TW-282RX)前，请确认相机和接收器是关机状态。 电缆线与设备连接时，请勿拉扯。 本产品属电子产品的附件，有可能因外界环境因素影响而造成相机不能或异常动 作，这种情况的可能性非常小。 不要使产品受到强烈振动，否则可能引起产品故障。 长时间不使用产品时，请将电池取出，以防电池渗漏腐蚀性液体而损坏产品。 请勿将产品置于高温中，如阳光直射下的封闭汽车内、控制面板等高温地方。 请保持干燥，切勿用湿手接触产品，亦不可将产品浸入水中或暴露雨中，否则可能 引起产品无法正常使用。 请勿在易燃易爆环境中使用本产品，违反此警告可能引起火灾或爆炸。 本产品涉及电池，关于电池的使用请严格按照相应的操作规范和注意事项，否则可 能引起火灾、爆炸或人身伤害。 4 利用无线遥控技术，实现对具备外接 插座的相机进行遥控操作。 采用FSK制式，提高了产品的可靠性和稳定性，使用2.4GHz全球免费无线频段， 15个可选通道。 控制距离可达80米以上。 使用液晶屏显示通道、电量、功能模式，简单易懂、操作方便。 超低功耗待机，传送器(TW-282TX)使用2节AAA电池，待机时间超过4年；接收器 (TW-282RX)使用3V CR-2锂电池，待机时间超过400小时。 可以更换不同型号的快门连接线控制不同品牌、不同型号的相机。。 可对相机进行单张拍摄、1秒连拍、B门拍摄、延时拍摄及定时计划拍摄的操作。 设定相关参数进行定时计划拍摄。 快门 5 TW-282简介 注意事项

3、快门连接线------------1条 1、传送器(TW-282TX) --- 1个 2、接收器(TW-282RX) --- 1个 下面介绍产品各部位名称: 1 3 2 6 7 4 5 8 电池欠压图标 接收器(TW-282RX) 通道显示屏幕 电源按钮/通道减少按钮 指示灯 背光灯按钮/通道增加按钮 电池盖 6 7 9 10 11 9 10 11 电池舱 热靴锁紧螺母 快装板固定螺母 热靴固定脚 控制信号输出接口 8 1 2 5 3 4 9 8 10 5 6 7 1 2 3 4

9 8 安装及使用设备 开始使用前，请您务必认真阅读相机的使用说明书，并了解相机的操作方法及功能 设定。因为相机的功能设定可能会影响到本产品对相机的有效控制。 安装更换电池 当传送器电池电量不足时，显示屏上的笔画明显变暗或电池 欠压图标[ ]将闪烁，则表示电池电压已经降到影响设备工作性 能的限度，应尽快更换电池。传送器使用二节AAA电池，如需更 换请按如下步骤进行: 1、滑动电池盖，将其打开。 传送器(TW-282TX) 2 时间显示区 3 功能区 1 定时计划功能区 4 单张拍摄图标 5 1秒连拍图标 7 延时拍摄图标 8 电池欠压图标 定时计划曝光时间图标 10 定时计划延时图标 9 定时拍摄间隔时间图标 11 定时拍摄张数图标 12 6 拍摄图标 1 3 2 4 5 6 7 8 10 9 传送器显示屏 11 1213 13 通信通道图标 13 输入插头 快门连接插头 DC0 DC1 DC2 E3 N3 L1 S1 UC1 快门连接线 1 2 1 2 各部位名称 CB1 CL- CL- CL- CL- CL- CL- CL- CL- CL-

11 10 固定接收器(TW-282RX) 安装及使用设备 安装及使用设备 可将接收器固定于相机机顶、机身附件固定架或三脚架上。 将接收器固定于相机机顶热靴。 从相机机顶卸下接收器时，需先松开热靴 螺母。切勿强行用 力拔出，以免损坏接收器和相机。 锁紧 固定时要锁紧热靴锁紧螺母。 2、按照电池舱内的正极[+]和负极[-]标志将电池正确装入。 3、关闭电池盖。 3、关闭电池盖。 安装电池时应注意电池的极性，错误的安装会使设备无法正常工 作，甚至损坏设备及造成人身伤害。 接收器(TW-282RX) TW-282RX 当接收器电池电量不足时，显示屏上的电池欠压图标[ ]将 闪烁，则表示电池电压已经降到影响设备工作性能的限度，应尽 快更换电池。接收器使用一节CR-2锂电池，如需更换请按如下 步骤进行: 1、滑动电池盖，将其打开。 2、按照电池舱内的正极[+]和负极[-]标志将电池正确装入。 安装电池时应注意电池的极性，错误的安装会使设备无法正常工 作，甚至损坏设备及造成人身伤害。 将 固定于相身附件上。 接收器 将 固定于三脚架上。 接收器 接收器安装时，应确保设备安装牢固，防止设备滑落。 1. 通过热靴脚底部螺母将接收器固定在快装板上。 2. 将快装板安装在三脚架上。

每隔2秒闪亮一次绿灯，屏幕显示通信通道。 2、打开电源后，之前设置的通信通道仍然有效。 3、接收器电源不会自动关闭，在开机状态下，按下电源按钮2秒 将关闭接收器电源。 2s 设置通信通道 设置传送器(TW-282TX)的通信通道 1、按左移按钮[ ]或右移按钮[ ]，将传送器活动功能图标移 至通道图标 [ ]。 2、按设置/确定按钮进入通道设置。此时，通道数字闪烁。 3、通过按数字增加按钮[ ]或数字减少按钮[ ]，调整通道号码。 4、再次按下设置/确定按钮，保存当前通道。 设置接收器(TW-282RX)的通信通道 1、打开电源，通信通道默认为上次设定的通道。 2、同时按下[+CH]和[CH-]按钮，进入通道设置，显示屏上的通 道图标[ ]闪烁。 3、按[+CH]通道增加1、[CH-]通道减少1。 4、再次同时按下[+CH]和[CH-]按钮或10秒无动作保存并退出设置。 *传送器与接收器必须保持相同频道才能进行有效控制.

15 14 安装及使用设备 在开机状态下，按住背光灯按钮2秒钟后，将打开背光灯。 接收器(TW-282RX) 打开背光灯后两次按键操作时间间隔在6秒钟内，背景灯将一直点亮。 背景灯不能手动关闭，在无任何操作6秒钟后将自动关闭。 打开背光灯 传送器(TW-282TX) 2s 按住背光灯按钮2秒钟后，将打开显示屏背光灯。 打开接收器背光灯后两次按键操作时间间隔在6秒钟内，背光灯将一直 点亮。 背光灯不能手动关闭，在无任何操作6秒钟后将自动关闭。 2s 将相机固定于三脚架或其它固定支架上。 插座保护盖，将连接线的快门插头插入相机的外接快门插座 确保接插到位，有锁紧螺母的需将螺母旋紧。 打开相机外接快门 大部分相机的外接快门插座带有防误插缺口，插入时请注意插头方 向，以免损坏相机的外接快门插座。 4、打开接收器电源，再打开相机电源。 接收器与相机的连接 1、 确认您的接收器已安装到位，并确保相机及接收器均已关机。 2、 首先将快门连接线的输入插头插入接收器的控制信号输出接 口，确认接插到位。 快门连接线没有插到位可能会造成定时器无法控制相机。 安装及使用设备 3、 ，

当相机功能设置为[ ]时，可能会出现连续拍摄。 当相机功能设置为[ ]时，相机将以B门功能拍摄，可能造成曝光不 足或过曝。 当相机功能设置为[ ]时，相机将会延时拍摄。 单张拍摄 1、在开机状态下通过按左移按钮[ ]或右移按钮[ ],将传送器的活动功能图标移至单 张拍摄图标[ ]。 2、 处于对焦状态，直至松开或全部按下。 半按释放按钮，传送器发出对焦信号，传送器和接收器上的绿色指示灯点亮，相机 在休眠状态下，按任何键能唤醒传送器并进入单张拍摄模式。

当相机功能设置为[ ]时，可能会每秒出现多次连续拍摄。 当相机功能设置为[ ]时，相机将以B门功能拍摄，可能造成曝光不 足或过曝。 当相机功能设置为[ ]时，相机将会执行一次或多次延时拍摄。 1秒连拍 1、在开机状态下通过按左移按钮[ ]或右移按钮[ ]， 传送器的活动功能图标 移至1秒连拍图标[ ]。 将 1秒连拍是品色公司首先推出的专利功能，在不改变相机单张拍摄功能的情况下实现1秒间隔的连拍。 应将相机功能设置为[ ] 。 当相机功能设置为[ ]时，相机只拍摄一次而不会进行B门拍摄。 当相机功能设置为[ ]时，相机将会进行连续拍摄。 当相机功能设置为[ ]时，相机将会延时拍摄一次。 拍摄 1、在开机状态下通过按左移按钮[ ]或右移按钮[ ]，将传送 器的活动功能图标移至B门拍摄图标[ ]。 2、 半按释放按钮，传送器发出对焦信号，传送器和接收器的绿 色指示灯点亮，相机处于对焦状态，直至松开或全部按下。 3、 全按释放按钮，传送器发出B门开始信号。传送器红灯开始 闪烁并且计时开始，接收器上的红灯保持点亮，接收器连续 输出拍摄信号。相机开始连续曝光拍摄。 4、 再次按下释放按钮，传送器输出B门拍摄停止信号，并显示 曝光时间相机停止曝光拍摄。