RIOTEC iLS6302NBQ Programming Quick Manual

-iLS6302NBQ -iLS6302NBM Connecting the Scanner Be sure that PC is turned OFF, before Connect scanner cable to the PC USB port on the PC as below described, Ensure that all connections are ready, and turn on your PC. 1. Please switch ON and charge scanner for 4~5 hours at first time before use. Scanner switch shown on Fig. 2. 2. After switch ON, the Orange LED will flash following with 3 beep-sounds. The RED LED will be OFF while it links to cradle within Bluetooth radio range. 3. If RED LED is continual ON, please re-plug USB cable, then, scan the 3 barcodes on the bottom of cradle sequentially. (Shown on Fig. 3 From 1 to 3). 4. Charging issue: Cradle works as charger when putting scanner on it. Even if the scanner's battery is full, the cradle will continue to supply power to the scanner. We suggest you to remove scanner from cradle when scanner is charged fully * Note: Please install PL-2303 driver for iLS6302NBM LED Indicator Information Orange LED ON Full charged Orange LED Flashing Charging / Low battery Red LED ON Offline / out of service Green LED ON Good read Orange LED ON Good read (Batch mode) Remark: * When the battery power is too low, the Orange LED will flash and beep once. Scanner should be charged immediately. * If scanner shuts down it is recommended to charge it fully before turning it back on. * Under power-saving mode, there will not be LED indication when charging. Reset Configuration to Defaults (scan from A1 to A2 for iLS6302NBQ or B1 to B3 for iLS6302NBM) iLS6302NBQ iLS6302NBM A1 Demo . B1 Demo . A2 Demo %D%F%T B2 Demo 20C1003 B3 Demo %D%F%T * Note: Please install PL-2303 driver for iLS6302NBM There are two operating modes on the scanner 1.Data Transmission mode (Default) Demo %M%A%F It is a necessary to scan “clean memory data" when switching between these two modes. Within Bluetooth radio range Beyond Bluetooth radio range Data read Transmit data to PC/terminal directly Save data into scanner’s memory, scanner will transmit data to PC/ terminal automatically when back to Bluetooth radio range. Enter Data Storage mode LED Green/ Orange LED flashes followed by 3 beeps. 2.Data Storage mode (Batch Mode) Demo %M%A%N It is a necessary to scan “clean memory data" when switching between these two modes. Data read Save data directly to scanner’s memory, It will transmit the data to PC/ terminal after you scan the Transmit memory data code. To delete data please scan the Clean memory data code. Enter Data Transmission mode LED Green/Orange LED flashes followed by 3 beeps. Always Clean memory data before switching to Data Transmission Mode. Otherwise Red/ Orange LED will flash with one long beep and will not switch modes. Under Data storage Mode The data can be keep or delete by option after transmit Demo %M%D%K Demo %M%D%E Keep the data (Default) Delete the data Demo %R%E%C Transmit memory data Green/Orange LED Flashes followed by 3 beeps Demo %E%R%A Clean memory data Green/Orange LED flashes followed by 3 beeps The barcode data which is stored in the memory will be deleted.

Demo %R%T%D Trigger standard (Default) (Trigger available, after data sent to the device) Transmission Speed Transmission speed is dependent on your device. In order not to lose data, please choose the correct speed. Middle-speed is the Default. Demo %B%T%H Demo . High-speed Ultra Slow-speed Transmission 1 transmission Demo . Demo . Middle-speed Ultra Slow-speed Transmission (Default) 2 transmission Demo %B%T%L Demo . Slow-speed Ultra Slow-speed Transmission 3 transmission Bluetooth Auto-connection Demo %A%L%E Bluetooth Auto-connection ON: When out of range, it will keep trying to connect to device, scanner will not enter power-saving mode. Demo %A%L%D Bluetooth Auto-connection OFF: When you are out of BT signal range, scanner will stop sending auto-connection signal to device after 2 minutes. During this time, it will not enter power-saving mode. Once you are back within range, press trigger to connect to the device. (Default) Keyboard Country(For USB HID only) Scan the appropriate country code as below to program the keyboard layout for your country or language. As a general rule, the following characters are supported, but need special care for countries other than the United States: @ | $ # { } [ ] = / ‘ \ < > ~ Demo %+-$.00 Demo %+-$.06 USA (Original setting) Italian Demo %+-$.01 Demo %+-$.07 Norway France Demo %+-$.02 www.tec-it.com %+-$.08 Germany Vietnam Demo %+-$.03 Demo %+-$.09 Sweden Spain Demo %+-$.04 Demo %+-$.10 Denmark Portugal Demo %+-$.05 Demo %+-$.11 Switzerland Hungary Power-saving Mode Demo %P%D%T00 Power-saving mode OFF Demo %P%D%T03 Power-saving mode ON (Default): Enter power-saving mode after 3-minute inactivity. This function converses battery power. When you press "SCAN/Power ON" button, it will wake up and begin to scan. Demo %P%D%T10 Power-saving mode ON: Enter power-saving mode after 10-minute inactivity. This function converses battery power. When you press "SCAN/Power ON" button, it will wake up and begin to scan. *When charging, the scanner will not enter power-saving mode automatically Redundancy Level This scanner offers two levels of decode redundancy. Select higher redundancy levels for decreasing levels of bar code quality. As redundancy levels increase, the decoder’s aggressiveness decreases. Select the redundancy level appropriate for the bar code quality. Demo . Redundancy Level 1 barcode must be successfully read twice before being decoded Demo . Redundancy Level 2 barcode must be successfully read three times before being decoded

barcode data Demo %C%P%S Demo %C%S%S prefix suffix 1. Scan above configuration code for Prefix or Suffix 2. Enter the required values (right, numeric barcode) for Prefix or Suffix using the hex values for the desired HEX values from “Prefix & Suffix TABLE (blew page)” 3. Then, end by scanning Code X (below, right) * The max. of special characters is 5. * When you append 1~4 required values for Prefix or Suffix, it must end with Code X. * It doesn’t need Code X, if you append 5 values to barcode data. How to delete Prefix or Suffix 1. Scan above configuration code for Prefix or Suffix 2. Enter the “0” “0” (above, right) 3. Then end by scanning Code X (below, right) Numeric barcode for settings Demo 0 Demo 6 Demo C Demo 1 Demo 7 Demo D Demo 2 Demo 8 Demo E Demo 3 Demo 9 www.tec-it.com F Demo 4 Demo A Demo 5 Demo B Demo X Prefix & Suffix TABLE HEX HID (SPP) HEX HID (SPP) HEX HEX HEX HEX 01 CTRL A (SOH) 19 CTRL Y (EM) 20 SPACE 38 8 50 P 68 h 02 CTRL B (STX) 1A CTRL Z(SUB) 21 ! 39 9 51 Q 69 i 03 CTRL C (ETX) 1B ESC (ESC) 22 " 3A : 52 R 6A j 04 CTRL D (EOT) 1C CTRL \ (FS) 23 # 3B ; 53 S 6B k 05 CTRL E (ENQ) 1D CTRL ] (GS) 24 $ 3C < 54 T 6C l 06 CTRL F (ACK) 1E CTRL ^ (RS) 25 % 3D = 55 U 6D m 07 CTRL G (BEL) 1F CTRL _ (US) 26 & 3E > 56 V 6E n 08 Backspace (BS) 27 ' 3F ? 57 W 6F o 09 Tab (HT) 28 ( 40 @ 58 X 70 p 0A CTRL J (LF) 29 ) 41 A 59 Y 71 q 0B CTRL K (VT) 2A * 42 B 5A Z 72 r 0C CTRL L (FF) 2B + 43 C 5B [ 73 s 0D Enter (CR) 2C , 44 D 5C \ 74 t 0E CTRL N (SO) 2D - 45 E 5D ] 75 u 0F CTRL O (SI) 2E . 46 F 5E ^ 76 v 10 CTRL P (DLE) 2F / 47 G 5F _ 77 w 11 CTRL Q (DC1) 30 0 48 H 60 ` 78 x 12 CTRL R (DC2) 31 1 49 I 61 a 79 y 13 CTRL S (DC3) 32 2 4A J 62 b 7A z 14 CTRL T (DC4) 33 3 4B K 63 c 7B { 15 CTRL U (NAK) 34 4 4C L 64 d 7C | 16 CTRL V (SYN) 35 5 4D M 65 e 7D } 17 CTRL W (ETB) 36 6 4E N 66 f 7E ~ 18 CTRL X (CAN) 37 7 4F O 67 g 1D Symbologies -1 ENABLE UPC-A DISABLE Demo . www.tec-it.com . ENABLE UPC-E DISABLE Demo . Demo . ENABLE EAN-8 DISABLE Demo . Demo . ENABLE EAN-13 DISABLE Demo . Demo . ENABLE ISBT 128 DISABLE www.tec-it.com . Demo .

ENABLE Code 39 FULL ASCII DISABLE www.tec-it.com . Demo . ENABLE Trioptic Code 39 DISABLE Demo . Demo . ENABLE Code 32 DISABLE Demo . Demo . ENABLE CODE 93 DISABLE Demo . Demo . ENABLE CODE 11 DISABLE Demo . Demo . ENABLE Interleaved 25 DISABLE Demo . www.tec-it.com . ENABLE Discrete 25 DISABLE Demo . Demo . ENABLE CODABAR DISABLE Demo . Demo . ENABLE MSI DISABLE Demo . Demo . 1D Symbologies -3 ENABLE Code 39 DISABLE www.tec-it.com . Demo . ENABLE Chinese 25 DISABLE www.tec-it.com . Demo . ENABLE Matrix 25 DISABLE Demo . Demo . ENABLE GS1 DataBar DISABLE Demo . Demo . ENABLE GS1 DataBar Limited DISABLE Demo . Demo . ENABLE GS1 DataBar Expanded DISABLE Demo . Demo . ENABLE Composite CC-C DISABLE Demo . Demo . ENABLE Composite CC-A/B DISABLE www.tec-it.com . Demo . ENABLE Composite TLC 39 DISABLE Demo . Demo . 2D Symbologie ENABLE PDF 417 DISABLE Demo . Demo . ENABLE Micro PDF 417 DISABLE Demo . Demo . ENABLE Data Matrix DISABLE Demo . Demo . ENABLE Maxicode DISABLE Demo . Demo . ENABLE QR CODE DISABLE Demo . Demo . ENABLE Micro QR CODE DISABLE Demo . Demo . ENABLE Aztec DISABLE Demo . Demo . Quick guide is subject to change without notice. R_180808_01