E.T. Systems DC BLUE ADVANCED Installer's Instructions

1 www.et.co.za Domestic garage door operator Installer Instructions

2 www.et.co.za TABLE OF CONTENTS Page Category Introduction 3 Safety obligations and general warnings. 4 Technical specifications. 5 Component identification and descriptions. Hardware installation 6 Installing the clutch release mechanism on the sledge/traveller. 7 Sectional overhead door – Installing the wall mount bracket. 7 Sectional overhead door – Installing the drawbar and hanging straps. 8 Sectional overhead door – Installing the door mount bracket. 8 Sectional overhead door – Installing the link arm. 8 Sectional overhead door – Testing the mechanical drive and linkage. 9 Trackless tip-up door – Installing the wall mount bracket. 10 Trackless tip-up door – Installing the door mount bracket. 10 Trackless tip-up door – Installing the link arm and hanging straps. 10 Trackless tip-up door – Testing the mechanical drive and linkage. 11 Both door types – Attaching the motor-head to the drawbar. 11 Both door types – Attaching the battery to the drawbar. 11 Both door types – Supplying household mains power to the motor-head. Control card wiring and setup 12 Wiring of optional extra devices to the system. 13 Control panel dashboard and programming menu summary. (How to navigate the menu) 14 Programming - Open and closed limit setup and door load profiling. 15 Programming - Setting the obstruction force sensing, safety level. 16 Programming - Activating safety beam mode. 17 Programming - Activating and selecting the auto-close time. 18 Programming - Selecting an electric lock mode. Receiver programming 19 Learning a new transmitter button code into the receiver memory. 20 Clearing a single transmitter button code from the receiver memory. 21 Master erasing all transmitter button codes from the receiver memory. 22 Quick method of learning a transmitter button code into the memory without entering the programming menu. Operating 23 Basic operating features using the (BT) button triggers. 25 Advanced operating features - Party mode. 26 Advanced operating features - Holiday lock-out mode. 27 Advanced operating features - Strike lock mode. 28 Advanced operating features - Magnetic lock mode. 29 Advanced operating features - Auto-close example. 29 Advanced features - Safety beam example. 30 Advanced features - Courtesy light operation. Troubleshooting 31 Buzzer, courtesy light and display warnings. Warranty 32 Warranty terms and conditions.

3 www.et.co.za IMPORTANT WARNINGS TO THE INSTALLER AND GENERAL SAFETY OBLIGATIONS • Caution! It is important for personal safety to follow all the instructions carefully. Incorrect installation or misuse may cause serious personal harm. • Keep the instructions in a safe place for future reference. • This product was designed and manufactured strictly for the use indicated in this documentation. Any other use not expressly indicated in this documentation, may damage the product and/or be a source of danger. • We accept no responsibility due to improper use or incorrect installation of this product. • We will not accept responsibility if the principles of good workmanship are disregarded by the installer. The construction of the door must be sound and automatable. It is the responsibility of the installer to ensure that all mountings to the door are sufficient to withstand the necessary forces in cases of overload. • It is highly recommended that a set of safety infra-red beams be used in conjunction with this product. • Over and above the recommendation to use safety infra-red beams with this product it is mandatory to install and use a safety beam set when using the automatic closing feature. • We accept no responsibility regarding safety and correct operation of the automation if other manufacturer’s equipment is added to this product. • Do not make any modifications or alterations to this product. • Anything other than expressly provided for in these instructions is not permitted. • Prior to installation: o The door must be balanced correctly to the tensioning system. When operated by hand the door should be free of hindrance and easily moved. When left at any position in its travel, the door should neither rise nor fall. If the door does rise or fall, re-balance the tensioning system. (Tensioning should only be carried out by a qualified and experienced person) o The door material must be sound and whole. Ensure the areas where the operator attaches have been re-enforced. The door hardware must be in good serviceable condition. o Ensure the wall above the door is sound and strong enough to allow proper fixing of the operator. If necessary use through bolts and/or cross brace plate to spread the load. (Typically on cinder brick or hollow walls) o The DC Blue Advanced is designed for weatherproof applications only. Install in completely walled and roofed garages only. o Ensure the area of installation is not subject to explosive hazards. There should be no volatile gasses or fumes as these can present a serious safety hazard. o The DC Blue Advanced is designed to be used in low traffic applications only. Do not install on doors used for multi parking garages like office parks or apartment blocks with a single entrance. o The DC Blue Advanced is supplied with a sealed 15A safety plug on lead for use in an electrical code of practice approved plug point. Do not extend, modify or replace the plug lead unless duly qualified as an electrician. Before installing the unit, ensure the mains supply is switched off. o It is the responsibility of the installer to ascertain that the designated persons (including children) intended to use the system, do not suffer reduced physical sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the system by a person responsible for their safety. o The drive may not be installed on a door incorporating a wicket door, unless the drive is disabled by the release of the wicket door. (Wicket door :- A pedestrian door within the main door) Cont.…..

4 www.et.co.za • Installation: o Remove all cables, latches/locks or catches not necessary for automation. o Ensure the working area is clear of obstructions and obstacles. o Install the door sticker depicting the safety reverse test and keeping door area clear. This sticker should be fixed to the inside surface of the door or near any permanent door control switches such as a wall console if installed. o The emergency release cord must be installed where it is no higher than 1.8m from the floor level. o Any additional fixed door control switches such as wall consoles, if installed, must be at a height of at least 1,5m, within clear sight of the door and away from any moving components of the system. o Do not substitute any component of DC Blue Advanced with any other manufacturer’s part. ET Systems accepts no responsibility for the safety and correct operation of the automation system if any of these points are ignored. • After Installation: It is the responsibility of the installer to ensure the user: o Is proficient in the use of the manual emergency release mechanism. o Is issued with the documentation accompanying this product. o Understands that the door may not be operated out of clear sight. o Ensures that children are kept clear of the door area and that children do not play with the remote transmitters. o Is instructed not to attempt to repair or adjust the automation system and to be aware of the danger of continuing to use the automation system in an unsafe condition before a service provider attends to it. o Is proficient in testing the unit’s safety obstruction sensing system by means of placing a 40mm high object (wooden block) below the door in the closed position. On contact with the object the unit must reverse the door away and back to the open position. * Based on the assumption that the door is balanced correctly and moving freely. TECHNICAL SPECIFICATIONS Primary power supply 220 – 240Vac @ 50hz Power consumption 120W peak @ (220 -240vac) Motor voltage 24V dc Maximum operations per day 50 full cycles per 24hrs @ a rate of Max. 2 per hour Traveller speed* 8m/min Operating temperature range -10 to 50° C (14F to 122F) Anti-crushing safety sensing Yes - Electronic digital profiling Auxiliary supply output 24Vdc @ 250mA peak or 150mA continuous Rated battery charging voltage 27.5Vdc Built in receiver format ET BLU MIX © enhanced rolling code. Receiver frequency 433.92Mhz Memory EEPROM Applicable door types One piece trackless tip-up or multiple panel sectional overhead doors Drawbar options(Ex-stock) 2.2m or 3.2m or 3.7m Applicable door sizes <13m²

5 www.et.co.za COMPONENT IDENTIFICATION AND DESCRIPTIONS Diagram number Description Qty Diagram number Description Qty 1 Wall mount bracket 1 20 Nylock nuts M8 8 2 Pivot pin 8mm x 90mm 1 21 Flat washers M6 6 3 Cotter pins 1.8mm x 35mm 3 22 Coach screws 8 x 60mm 2 4 Door mount bracket 1 23 Coach screws 8 x 40mm 6 5 Straight link arm 1 24 Wall plugs 10mm 2 6 Curved link arm extension 1 25 Warning sticker 1 7 Emergency release assembly 1 26 24Vdc 3.5A/h Battery (Optional extra) 1 8 Round head machine screws M6 x 20mm 4 27 Motor-head 1 9 Emergency release cord 1.1m with warning tag 1 28 Control panel dashboard 1 10 Emergency release cord plastic knob/handle 1 29 Courtesy light diffuser lens 1 11 Pivot pins 8mm x 25mm 2 30 Drawbar 1 12 Hanging strap drawbar attachment bracket 1 31 Drawbar spring dampener and shock absorber 1 13 Drawbar brackets 3 32 Battery connection beneath dust cover sticker 1 14 Battery straps 2 33 E-Coms connection plug with dust cover 1 15 Hanging straps 1m 3 34 Drawbar back-end 1 16 Machine bolts 10mm head M6 x 15mm 2 35 Splined sprocket with chain 1 17 Machine bolts 14mm head M8 x 15mm 8 36 Household mains cord 1.5m 1 18 Machine nuts M6 4 37 Auxiliaries connection plug with dust cover 1 19 Nylock nuts M6 6 38 Cover screws 4

6 www.et.co.za HARDWARE INSTALLATION INSTALLING THE MANUAL OVERRIDE CLUTCH ASSEMBLY ONTO THE SLEDGE/TRAVELLER (See page 5 for component identification) The diagrams below show how to install the manual override clutch assembly onto the sledge traveller. Ensure the 4 machine screws are securely fastened. Do this prior to installing the drawbar. ! CAUTION TO DISENGAGE AND MOVE DOOR MANUALLY: Warning! Door may plummet closed when released. W hile pulling t he emergency release cord dow nw ard, move t he door open or closed by hand. TO RE-ENGAGE AND LOCK DOOR BACK ONTO DRIVE: Let t he cord go and move door open or closed unt il the sledge/t raveller locks back ont o t he chain drive. Install the manual override label as shown here.

7 www.et.co.za HARDWARE INSTALLATION Standard Single Track or Double Track Sectional Garage Door Method INSTALLING THE WALL MOUNT BRACKET (See page 5 for component identification) The diagram below shows how to determine the mounting height and position of the wall mount bracket, in the case of a standard single track or double track overhead sectional garage door system. NB!!! The wall mount bracket is one of the components that take the majority of the load in a garage door automation system. Extra care needs to be taken to ensure the bracket is securely fastened and that whatever the bracket is fastened to, can withstand force equal to the force of the door when the spring balancing of the door is removed (snapped) INSTALLING THE DRAWBAR AND HANGING STRAPS (See page 5 for component identification)

8 www.et.co.za TESTING THE MECHANICAL DRIVE AND LINKAGE It is now possible to test the mechanical movement of the door with the link arm attached and the sledge/traveller engaged onto the chain drive. The movement of the door throughout its travel should be approximately the same while pulling the chain around the drawbar, as it is when the chain is not engaged. If satisfied that the drawbar is not causing unnecessary drag or hindrance to the door movement, then go ahead and attach the motor-head to the drawbar. (Page 11) INSTALLING THE DOOR MOUNT BRACKET (See page 5 for component identification) Mount the door mount bracket on the inside fascia of the door as shown below. Keep it as in line as possible with the top guide rollers and centred from side to side of the door. NB!!! The door mount bracket is one of the components that will take the majority of the load in a garage door automation system. Extra care needs to be taken to ensure that the bracket is securely fastened. Whatever the bracket is fastened to, must also withstand a force equal to the force of the door when the spring balancing of the door is removed. For example if a balancing spring snaps. INSTALLING THE LINK ARM (See page 5 for component identification) Close the door fully. Install the curved link arm extension in the door mount bracket using one of the cotter pins and 25mm long pivot pins supplied. Next using the other 25mm long pivot pin and cotter pin, install the straight link arm in the traveller/sledge that has been moved all the way to the front of the drawbar. Finally bolt the curved extension to the straight link arm, so that the two combined form the same angle as shown below. This method provides better positive locking of the door in the closed position than the commonly used 45⁰ angled link arm. This method also produces less backward force on the gearbox when trying to compress the seal at the bottom of the door as the downward force is generated by the link arm camming up and over the door.

9 www.et.co.za HARDWARE INSTALLATION Trackless tip-up door INSTALLING THE WALL MOUNT BRACKET (See page 5 for component identification) From the top edge of the door in the closed position, measure 275 – 300mm perpendicular to the top edge of the door. Install the wall mount bracket at this height where it is positioned above the centre of the door as shown in the diagram below. NB!!! The wall mount bracket is one of the components that will take the majority of the load in a garage door automation system. Extra care needs to be taken to ensure that the bracket is securely fastened. Whatever the bracket is fastened to, must also withstand a force equal to the force of the door when the spring balancing of the door is removed. For example if a balancing spring snaps.

10 www.et.co.za INSTALLING THE DOOR MOUNT BRACKET (See page 5 for component identification) Mount the door mount bracket on the top edge of the door, where it is centred from side to side of the door. NB!!! The door mount bracket is one of the components that will take the majority of the load in a garage door automation system. Extra care needs to be taken to ensure that the bracket is securely fastened. Whatever the bracket is fastened to, must also withstand a force equal to the force of the door when the spring balancing of the door is removed. For example if a balancing spring snaps. INSTALLING THE LINK ARM AND HANGING STRAPS (See page 5 for component identification) Install the front end of the drawbar in the wall mount bracket using the 90mm pivot pin and one of the cotter pins. Raise the drawbar up and out of the way of the door. Install the link arm into both the sledge/traveller and door mount bracket using the 25mm pivot pins and remaining two cotter pins. Prepare and install the hanging straps so that when the door is in the full open position, the link arm lays 180⁰ to the door. Do not use the curved link arm extension in this type of installation. The diagram below shows the final position of the drawbar when installed and examples of how to prepare the hanging straps. TESTING THE MECHANICAL DRIVE AND LINKAGE It is now possible to test the mechanical movement of the door with the link arm attached and the sledge/traveller engaged onto the chain drive. The movement of the door throughout its travel should be approximately the same while pulling the chain around the drawbar, as it is when the chain is not engaged. If satisfied that the drawbar is not causing unnecessary drag or hindrance to the door movement, then go ahead and attach the motor-head to the drawbar. (Page 11)

11 www.et.co.za ATTACHING THE MOTOR-HEAD TO THE DRAWBAR (See page 5 for component identification) Insert the splined motor drive shaft into the splined sprocket at the back-end of the drawbar. Swivel the motor-head around so that the motor mounting straps are able to fit over the drawbar and onto the mounting studs on the motor-head. Fasten the drawbar mounting straps onto the motor-head using the 4 M6 machine nuts and M6 flat washers. ATTACHING THE BATTERY TO THE DRAWBAR (See page 5 for component identification) Making use of the extended length mounting straps and 4 of the M6 Nylock nuts fasten the battery atop the drawbar as shown below. Remove the sticker covering the battery plug socket on the motor-head and insert the battery lead plug. The battery plug is moulded in such a way as to only be inserted in one direction. Ensure the plug is in firmly. SUPPLYING HOUSEHOLD POWER TO THE MOTOR-HEAD The DC BLUE ADVANCED © comes supplied with an IEC and SANS compliant 220Vac power cord, 1,5m in length. Plug the sealed non-serviceable 3 pin 15Amp plug into a certified 15Amp plug socket that is installed outside of the workings of the garage door system, yet still within reach of the power cord. Ensure the there is no strain on the cord once installed. Also ensure that nothing will catch or snag the power cord when the garage door is moving or when people or cars pass below the system.

12 www.et.co.za OPTIONAL EXTRA DEVICES WIRING CONNECTIONS

13 www.et.co.za CONTROL PANEL DASHBOARD AND PROGRAMMING MENU SUMMARY (How to navigate the menu options) NOTE! Before attempting to execute the instructions, read the complete instruction table, for a setup option. Some steps require a response before a safety timeout expires and you may still be reading the next step when the timeout expires. • To enter the Programming menu from Standby mode, press and hold the “SET” button until the buzzer beeps twice. • Once in the Programming menu, use the up and down buttons to scroll between options. • For further instruction on changing settings, refer to the instruction tables on the page indicated for each option. EXIT BUTTON • To exit a setup option without changing the current setting for that option, press and release the “EXIT” button. The menu will exit back one level. • Note 1: If the “EXIT” button is pressed before completing the Limit and door profile setup, no limit and door profile settings will be in memory. You must complete this setup to operate the door. (See “P” symbol displayed in the Trouble shooting table on page 31)

14 www.et.co.za PROGRAMMING Open and closed limit position setup and door load profiling. From Standby Mode Action Response To enter the program menu. Press and hold SET button until buzzer beeps twice. Display begins flashing “P” and buzzer beeps twice to confirm the main program menu is active. Scroll up with the UP button until “L” flashes. Display flashes “L” to confirm limit setup mode is selected. Press and release SET button to begin limit setup. Buzzer beeps once and “O” displays to indicate open limit position must be set. Press and hold the UP button to raise the door to the required open position. The “n” symbol displays as the door opens. Fine tune using the UP and DOWN buttons. The “n” and “u” symbols confirm the door direction while fine tuning. or When satisfied the door is in the correct open position, press the SET button to advance to the close limit setup. The buzzer beeps once and the “C” symbol displays to indicate the closed limit position must be set. Press and hold the DOWN button to lower the door to the required closed position. The “u” symbol displays as the door closes. Fine tune using the UP and DOWN buttons. The “n” and “u” symbols confirm the door direction while fine tuning. or When satisfied the door is in the correct closed position, press the SET button to advance to the automatic door load profiling stage. Door opens and closes again. The display confirms the direction and the buzzer will beep intermittently as the motor runs. When complete, the control returns to the main program menu. Display = Flashing “P” and buzzer beeps once. Scroll up or down to next program option. OR Press and release EXIT to return to Standby mode. See Note 1 on page 13!!!

15 www.et.co.za SAFETY OBSTRUCTION SENSING IN ACTION: In the case of the door being resisted physically or obstructed while opening. • The motor will stop running, • The buzzer will beep once and operator reverts to standby mode. • On the next BT button trigger the motor will start closing the door. In the case of the door being resisted physically or obstructed while closing. • The motor will stop running, • The buzzer will beep once as the motor immediately begins opening the door once again. • On reaching the open position the operator reverts to standby mode. • On the next BT button trigger the motor will begin the door closing. SETTING THE OBSTRUCTION FORCE SENSING, SAFETY LEVEL. Default level - 3 From Standby Mode Action Response To enter the Program menu. Press and hold SET button until buzzer beeps twice. Display begins flashing “P” and buzzer beeps twice to confirm the main program menu is active. Scroll up with the UP button until “F” flashes. Display flashes “F” to confirm safety force setup mode is selected. Press and release SET button to enter safety force setup. Buzzer beeps once and current safety force level is displayed. (1-9) Press and release the UP or DOWN buttons to scroll to the desired safety force level. (1-9) 1 = most sensitive to resistance in movement of the door. 9 = least sensitive to resistance in movement of the door. Press and release the SET button to save the new setting to memory and exit back to the main program menu. The buzzer beeps once and the display returns to flashing “P”. To Scroll up or down to next program option. OR Press and release EXIT to return to Standby mode.

16 www.et.co.za ACTIVATING SAFETY BEAM MODE. Default – Off (Disabled) NB! When auto-close mode is activated, the safety beam mode automatically becomes active. This is mandatory as auto-close mode may never be used without a set of safety beams installed. With auto-close active, safety beam setup mode is no longer available in the setup menu. From Standby Mode Action Response To enter the Program menu. Press and hold SET button until buzzer beeps twice. Display begins flashing “P” and buzzer beeps twice to confirm the main program menu is active. Select safety beams setup by scrolling up with the UP button until “b” flashes. Display flashes “b” to confirm safety beam setup mode is selected. Press and release SET button to enter safety beam setup. Buzzer beeps once and current beam status is displayed. 0 = Off and 1 = On Press and release the UP button for On or DOWN button for Off selection. 0 = Off (Disabled) 1 = On (Active) Press and release the SET button to save the new setting to memory and exit back to the main program menu. The buzzer beeps once and the display returns to flashing “P”. OR Scroll up or down to next program option. OR Press and release EXIT to return to Standby mode.

17 www.et.co.za ACTIVATING THE AUTO-CLOSE MODE AND SELECTING AN AUTO-CLOSE TIME. Default – Off NB! When auto-close mode is activated, the safety beam mode automatically becomes active. This is mandatory as auto-close mode may never be used without a set of safety beams installed. With auto-close active, safety beam setup mode is no longer available in the setup menu. From Standby Mode Action Response To enter the Program menu. Press and hold SET button until buzzer beeps twice. Display begins flashing “P” and buzzer beeps twice to confirm the main program menu is active. Select auto-close setup by scrolling up with the UP button until “A” flashes. Display flashes “A” to confirm auto-close setup mode is selected. Press and release SET button to enter auto- close setup. Buzzer beeps once and current auto-close status is displayed. Press and release the UP or DOWN buttons to scroll to the desired setting. 0 = Off. 5 = 50 sec. 1 = 10sec. 6 = 60sec. 2 = 20sec. 7 = 70sec. 3 = 30sec. 8 = 80sec. 4 = 40sec. 9 = 90sec. Press and release the SET button to save the new setting to memory and exit back to the main program menu. The buzzer beeps once and the display returns to flashing “P”. To Scroll up or down to next program option. OR Press and release EXIT to return to Standby mode.

18 www.et.co.za SELECTING A LOCK MODE. Default – Off NB!! The “E-Coms” output on the control card is designated to be used with an “E-Coms” Relay module, when using any electric lock. These modules are only available via ET Systems. For further instructions on the E-Coms relay module, consult the instructions included with it. For assistance the product support department can be contacted on: 0861 109 9238 or [email protected] In strike lock mode, the lock relay will energise 0.5sec before the motor begins opening and release again 0.5sec after the motor has begun moving. (Total 1sec. pulse length) In magnetic lock mode, the lock relay will energise, 0.5sec before the motor starts opening and 5 seconds later, the lock relay module switches off again. (Total 5sec. pulse length) From Standby Mode Action Response To enter the Program menu. Press and hold SET button until buzzer beeps twice. Display begins flashing “P” and buzzer beeps twice to confirm the main program menu is active. Select lock setup by scrolling up with the UP button until “” flashes. Display flashes “” to confirm lock setup mode is selected. Press and release SET button to enter lock setup. Buzzer beeps once and current lock status is displayed. Press and release the UP or DOWN buttons to scroll to the desired setting. 0 = Off. 1 = Strike lock. 2 = Magnetic lock. Press and release the SET button to save the new setting to memory and exit back to the main program menu. The buzzer beeps once and the display returns to flashing “P”. To Scroll up or down to next program option. OR Press and release EXIT to return to Standby mode.

19 www.et.co.za LEARNING A TRANSMITTER CODE IN THE RECEIVER MEMORY. Max users (BT) button trigger channel = 35 user codes Max users (LT) courtesy light trigger channel = 5 user codes NB!! The built in receiver will only work with the ET BLU MIX © enhanced rolling code or ET BLUE rolling code transmitters. From Standby Mode Action Response To enter the Program menu. Press and hold SET button until buzzer beeps twice. Display begins flashing “P” and buzzer beeps twice to confirm the main program menu is active. Select receiver setup by scrolling up with the UP button until “r” flashes. Display flashes “r” to confirm receiver programming menu is selected. Press and release SET button to enter receiver programming. Buzzer beeps once and “b” for (BT) is displayed. Press and release the UP or DOWN buttons to scroll to the channel the remote button must be learnt into. b = (BT) button trigger channel. L = (LT) Courtesy light trigger channel. or Press and hold desired remote button. LED on remote transmitter illuminates. While still holding the desired remote button, press and release the “SET” button. “1” on display and 1 beep = user code successfully learnt. “2” on display and 2 beeps = user code already in the receiver memory. “3” on display and 3 beeps = Unsuccessful because no code was seen within 4 sec of the SET button being pressed. Mandatory timeout. “F” on display and multiple rapid beeps = Memory full The display returns to flashing “r”. Receiver programming menu. Release the remote button Memory full Code already in memory Successful Unsuccessful Scroll up or down to next program option. OR Press and release EXIT to return to Standby mode.

20 www.et.co.za CLEARING A SINGLE TRANSMITTER BUTTON CODE FROM THE RECEIVER MEMORY. This can only be completed if the remote control that must be erased is present. If the remote control that must be removed is missing or unobtainable, then a master erase procedure (Page 21) must be performed and the remaining, valid user codes must all be learnt into the memory once again. From Standby Mode Action Response To enter the Program menu. Press and hold SET button until buzzer beeps twice. Display begins flashing “P” and buzzer beeps twice to confirm the main program menu is active. Select receiver setup by scrolling up with the UP button until “r” flashes. Display flashes “r” to confirm receiver setup mode is selected. Press and release SET button to enter receiver setup. Buzzer beeps once and “b” is displayed. Press and release the UP or DOWN buttons to scroll to the “C” option. “C” is displayed. Press and hold desired remote button to be erased. LED on remote transmitter illuminates. While still holding the desired button, press and release SET button. “0” on display and 1 beep = user code successfully erased. “3” on display and 3 beeps = Unsuccessful because no code was seen within 4 sec of the SET button being pressed. Mandatory timeout. Release the remote button Display reverts back to flashing “r” to indicate you have returned to the receiver setup menu. Unsuccessful Scroll up or down to next program option. OR Press and release EXIT to return to Standby mode.

21 www.et.co.za MASTER ERASING ALL TRANSMITTER BUTTON CODES FROM THE MEMORY. From Standby Mode Action Response To enter the Program menu. Press and hold SET button until buzzer beeps twice. Display begins flashing “P” and buzzer beeps twice to confirm the main program menu is active. Select receiver setup by scrolling up with the UP button until “r” flashes. Display flashes “r” to confirm receiver setup mode is selected. Press and release SET button to enter receiver setup. Buzzer beeps once and “b” is displayed. Press and release the UP button to scroll to the “E” option. “E” is displayed. Press and hold SET button and do not release. While still holding the SET button. Press and release UP button to start master erase. Release both buttons once beeps begin. Display flashes “E” and buzzer beeps intermittently to warn that master erase is about to begin. NB! Pressing and holding EXIT at this point will abort the master erase. Master erase routine is running. Wait. Display goes blank and buzzer silences to indicate erase has commenced. Master erase routine is running. Continue waiting. Display stays “0” and buzzer emits 1 long beep, to indicate Master erase is complete. Display reverts back to flashing “r” to indicate you have returned to the receiver setup up menu. Scroll up or down to next program option. OR Press and release EXIT to return to Standby mode.

22 www.et.co.za A QUICK METHOD OF LEARNING A TRANSMITTER BUTTON CODE INTO THE RECEIVER MEMORY WITHOUT ENTERING THE PROGRAMMING MENU. Max users (BT) button trigger channel = 35 user codes NB!! No remote codes can be learnt into the (LT) courtesy light channel this way. Action Response Door must be closed Door closed Press and hold the “Up” button until buzzer beeps and display shows “b”. Buzzer beeps once and display shows “b” Press and hold required remote button. LED on remote transmitter remains lit. Press and release the “SET” button. “1” on display and 1 beep = user code successfully registered. “2” on display and 2 beeps = user code already in the receiver memory. “3” on display and 3 beeps = Unsuccessful because no code was seen within 4 sec of the “SET” button being pressed. Mandatory timeout. “F” on display and multiple rapid beeps = Memory full Release both the remote button and “SET” button Display reverts back standby mode “II” Memory full Code already in memory Successful Unsuccessful

23 www.et.co.za BASIC OPERATING FEATURES Basic open and close triggers using the (BT) button trigger. Example 1. Simply opening the door fully and closing the door again fully. Action Response Door in the closed position. Courtesy light off. Press and release either the remote button trigger or the hardwired trigger. Door begins opening and courtesy light switches on. Wait for door to reach the full open position. Door stops and waits in the open position. Courtesy light remains on for a further 3 minutes. Press and release either the remote button trigger or the hardwired trigger. Door begins closing and if the courtesy light had previously timed out and switched off, it will switch on again for three minutes. Wait for door to reach the closed position. Door stops in the closed position. Light remains on until three minute timer has expired.

24 www.et.co.za BASIC OPERATING FEATURES Basic open and close triggers using the (BT) button trigger. Example 2. Using the (BT) button trigger input while the door is running. Action Response Door in the closed position. Courtesy light off. Press and release either the remote button trigger or the hardwired trigger. Door begins opening and courtesy light switches on. Press and release either the remote button trigger or the hardwired trigger, before the door reaches the full open position Door stops and waits for next instruction. Courtesy light remains on for a further 3 minutes. Press and release either the remote button trigger or the hardwired trigger. Door begins closing and if the courtesy light had previously timed out and switched off, it will switch on again for three minutes. Press and release either the remote button trigger or the hardwired trigger, while the door is still closing. Door stops and begins opening once again. Light remains on until three minute timer has expired.

25 www.et.co.za ADVANCED OPERATING FEATURES Advanced triggers using the remote (BT) button trigger (PARTY MODE) Example 3. Using the remote (BT) button trigger to disable any closing triggers Action Response TO ACTIVATE Door in the closed position. Courtesy light off. Press and release either the remote button trigger or the hardwired trigger. Door begins opening and courtesy light switches on. Stop door while opening or simply wait until it reaches the open position. Door stops and waits at the required open position. Courtesy light remains on for a further 3 minutes. Press and hold the remote button trigger, +/- 10 seconds, until buzzer beeps. Buzzer beeps rapidly to indicate party mode is active. TO CONFIRM Any attempt to operate the door normally. Buzzer repeats rapid beeps to indicate the party mode is still active. The door will not move. TO DE-ACTIVATE Press and hold the remote button trigger +/- 10 seconds, until buzzer beeps. Buzzer beeps once and door starts closing. Courtesy light switches on for three minutes. Rapid Rapid

26 www.et.co.za ADVANCED OPERATING FEATURES Advanced triggers via the remote (BT) button trigger and (LT) courtesy light trigger (HOLIDAY LOCK-OUT MODE) Example 4. Using the remote (BT) button trigger and (LT) courtesy light to lock out any opening triggers Action Response TO ACTIVATE Door must be closed Door in the closed position. Courtesy light off. Press and hold remote courtesy light button. Courtesy light switches on. Release button when buzzer begins to sound. After +/- 5 seconds. Buzzer tones for 5 seconds. Courtesy light remains on. Whilst buzzer is still sounding, Press and release the remote trigger button, to activate Holiday lock- out. Buzzer beeps, light flashes rapidly and display shows “H” to indicate Holiday lock-out is active. TO CONFIRM Any attempt to operate the door normally. Buzzer beeps, light flashes rapidly and display shows “H” to indicate Holiday lock-out is active. TO DE-ACTIVATE Press and hold remote courtesy light button. Courtesy light switches on. Release button when buzzer begins to sound. After +/- 5 seconds. Buzzer tones for 5 seconds. Courtesy light remains on. Whilst buzzer is still sounding, Press and release the remote trigger button, to de- activate Holiday lock- out. Buzzer beeps once, courtesy light remains on and the door begins opening as Holiday lock- out de-activates. Rapid Rapid

27 www.et.co.za ADVANCED OPERATING FEATURES LOCK MODES – STRIKE LOCK MODE. NB!! This function is only available if an ET E-Coms relay module is installed. Action Response Door in the closed position. Courtesy light off. Lock relay module off. Press and release either the remote button trigger or the hardwired trigger. 0.5 seconds before the door begins opening, the lock relay module and courtesy light switches on. Door begins opening, lock relay module and courtesy light remains on. 0.5 seconds after door begins opening, the lock relay module switches off again. Door continues opening and light remains on for 3 minutes.

28 www.et.co.za ADVANCED OPERATING FEATURES LOCK MODES – MAGNETIC LOCK MODE. NB!! This function is only available if an ET E-Coms relay module is installed. Action Response Door in the closed position. Courtesy light and lock relay module, off. Press and release either the remote button trigger or the hardwired trigger. 0.5 seconds before the door begins opening, the lock relay module and courtesy light switches on. Door begins opening, lock relay module and courtesy light remains on. 5 seconds after door begins opening, the lock relay module switches off again. Door continues opening and light remains on for 3 minutes.

29 www.et.co.za ADVANCED OPERATING FEATURES Auto-close feature. Action Response Door in the closed position. Courtesy light off. Press and release either the remote button trigger or the hardwired trigger. Door begins opening and courtesy light switches on. On reaching the full open position, the auto- close timer times out the previously programmed auto-close time. 20 sec. for example. Courtesy light and buzzer, flashes and sounds three times, before door begins closing automatically. ADVANCED FEATURES Safety beam input NB!! This input only affects the closing cycle. Action Response Door closing. Light on. Interrupt the safety beams. Display shows “b”, door stops and begins opening once again. Light remains on. Safety beam still interrupted. Door reaches full open position. Display continues to show “b” as long as the safety beams are interrupted. Light switches off after 3min. Any further closing triggers while beams are still interrupted. Door will not close. Display continues to show “b” as long as the safety beams are interrupted and buzzer beeps once. X 3

30 www.et.co.za ADVANCED FEATURES Courtesy light NB!! In the case of a household mains failure, the courtesy light does not function. The buzzer will also emit a short beep every 15 seconds for 5 minutes after any BT transaction when the household mains power is off. Action Response Every operation of the door from any position. Light will come on for 3 minutes and door operates. If the light is off and the (L) courtesy light button on the remote is pressed and released. Light will come on for 60 minutes. If the light is on and the (L) courtesy light button on the remote is pressed and released. The courtesy light simply switches off. For 3 minutes For 60 minutes

31 www.et.co.za WARNINGS WHEN USING A (BT) BUTTON TRIGGER FROM STANDBY MODE. Display Buzzer and light Reason Resolve by. Safety beam obstructed. Page 29 Holiday lock-out active. Page 26 Open/closed limits and load profile routine incorrectly setup or exited without completing. Page 14 Party mode active. Page 25 Household mains power failure. On battery power only. Re-connect household mains supply. To test. Check that light switches on when operating door. Page 30 Door stops • Motor fuse blown or, • Encoder faulty or disconnected. • Replace motor fuse or, • Reconnect or replace encoder. Press and release “EXIT” when done. WARNINGS WHEN ATTEMPTING TO PROGRAM THE OPEN AND CLOSED LIMITS AND DOOR PROFILING. Display Buzzer and door Reason Resolve by Door stops • Door physically jammed. • Clear physical door obstruction or, Press and release “EXIT” when done. Rapid Rapid X 5 Light 1 short beep every 15 sec. (Beep stops 5 minutes after each door operation)

32 www.et.co.za WARRANTY: All goods manufactured by G&C Electronics cc T/A ET Systems carry a 12 month factory warranty from date of invoice. All goods are warranted to be free of faulty components and manufacturing defects. Faulty goods will be repaired or replaced at the sole discretion of ET Systems free of charge. This warranty is subject to the goods being returned to the premises of ET Systems. The carriage of goods is for the customer’s account. This warranty is only valid if the correct installation and application of goods, as laid out in the applicable documentation accompanying said goods, is adhered to. All warranty claims must be accompanied by the original invoice. All claims made by the end user must be directed to their respective service provider/installer. The following conditions will disqualify this product from the warranty as laid out above. These conditions are non-negotiable. • Any unauthorized non-manufacturer modifications to the product or components thereof. • The use of the ET DC BLUE ADVANCED operator in heavy traffic applications such as office parks and residential complexes. • The use of the DC BLUE ADVANCED operator in non-weatherproof applications such as car ports. The following items are not included in the warranty. • The battery. • The motor brushes. • Damage due to the following: o Wind and other climatic influences such as lightning strikes. o Water/moisture ingress. (This unit is not designed for use outdoors. I.e. carports. o High voltage surges on the household mains. o Infestation i.e. Ants nesting…