Alula RE301 Quick Start Manual

with industry-leading wireless range and battery life. It is typically used to sense opening and closing of doors and windows, but can secure just about anything using its two external contact zones. It will alarm when the magnet is pulled away from the sensor or when an external contact is opened. Features • Industry-leading wireless range and battery life • One door window zone and two external contact zones • Secure encrypted wireless transmissions • 5 year warranty Enroll zones by placing panel into wireless enrollment mode. ESN IDs • Reed Switch Zone 0 = ESN ends in “0” and is labeled on the DWS battery bucket • External Contact Zone 1 = Same as Reed Switch Zone with last digit replaced by a “1” • External Contact Zone 2 = Same as Reed Switch Zone with last digit replaced by a “2” Install by mounting the sensor and magnet on a door or window using the mounting screw locations. Make sure to align the alignment marks on the sensor and magnet when mounting. Additionally, the sensor can be used with up to two external contacts. External Contacts • Use normally-closed contacts because the door window sensor will transmit an alarm when it sees an external contact open • Do not use end-of-line resistors • Activate only the zones you need Mounting Screw Holes Use the panel installation guide to verify proper system setup. RE301 Door Window Sensor DSC® Compatible I N S T A L L G U I D E I Resolution Compatibles Enroll Reed Switch • Remove battery tab and trip tamper to enroll • Sensor ID for reed switch ends in “0” and is labeled on the DWS battery bucket Enrolling External Sensors • Trip external sensors to enroll • External 1 has same ID except it ends in “1” • External 2 has same ID except it ends in “2” • Trip only the zones on the DWS you want to enroll • The two external contact zones must be “activated” in order to report. Short zones while installing battery to activate. all-guide s.com

applied for over 10 seconds. Surface Preparation • Clean the surface • Ensure the mounting surface temperature is above 50 °F Wireless performance is optimized when mounted near the top of the door in a vertical orientation. OK BEST WRONG Wire an external contact by securing one wire to either the external 1 or external 2 port and the other wire to the common port. If both external contacts are used two wires will be inserted into the common port. Battery - + Cover Tamper rnal 1 m nal 1 Magnetic Reed Switch External 1 Terminal External 2 Terminal Center Common Terminal Tamper

X Axis Z Axis Non-Ferromagnetic Surface Nominal Mounting Distance X Axis - Make Break Y Axis - Make Break Z Axis - Make Break 1.00 inches (2.5 cm) 1.10 inches (2.8 cm) 1.30 inches (3.3 cm) 2.40 inches (6.1 cm) 2.55 inches (6.5 cm) 1.20 inches (3.0 cm) 1.35 inches (3.5 cm) Ferromagnetic Surface Nominal Mounting Distance X Axis - Make Break Y Axis - Make Break Z Axis - Make Break 0.50 inches (1.2 cm) 0.60 inches (1.5 cm) 0.65 inches (1.7 cm) 1.70 inches (4.3 cm) 1.75 inches (4.5 cm) 1.05 inches (2.7 cm) 1.10 inches (2.9 cm) Y Axis

Physical Housing Dimensions Weight with Battery Mounting Fastener 3.25 x 1.40 x 1.05 inches (8.3 x 3.6 x 2.7 cm) 1.90 ounces (54 grams) Four #6 screws (provided) Environmental Operating Temperature Maximum Humidity 32° to 120 °F (0° to 49 °C) 85% non-condensing relative humidity Sensor Specifications Frequency Replacement Battery Nominal Battery Life Battery Voltage Current Draw Transmitted Indications Max Wire Length on External Contacts 433.92 MHz One Panasonic® CR123A 10 to 15 years 3.0 VDC (Nominal), 2.2 VDC (Low) 20 mA (Maximum), 0.6 uA (Quiescent) Cover Tamper, Low Battery, Supervision 7.5 feet Certification RE301 FCC, IC Specifications 47-0004-03 • REV C • 2018-12-11 Tech Support Line • (888) 88-ALULA • (888) 882-5852 alula.net 01 WARRANTY Alula will replace non-portable products that are defective in their first five (5) years, and portable products that are defective in their first two (2) years. IC NOTICE This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux cnr d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) L’appareil ne doit pas produire de brouillage, et (2) L’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. IC: 8310A-RE301 FCC NOTICE This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference that may be received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Alula could void the user’s authority to operate this equipment. FCC ID: U5X-RE301 TRADEMARKS Alula is a trademark owned by Alula Holdings, LLC. “DSC” is a trademark owned by TYCO. Alula products will function with DSC systems. However, no Alula product is produced by, endorsed by, or is officially associated with DSC. Alula recommends verifying proper enrollment and operation, per control panel installation instructions, at installation. 3M and VHB are trademarks owned by 3M Company. Panasonic is a trademark owned by Panasonic Corporation.