Baumatic BTI9170GL Instruction Manual

BTI9170GL Cooker Hood 90 cm Glass island cooker hood in stainless steel NOTE: This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is easily available for future reference; for you or any person not familiar with the operation of the appliance. DD 02/03/09 2

5 – 7 Specifications of your cooker hood 8 Using your Baumatic cooker hood 9 - 10 Before first use 9 To use your cooker hood 9 – 10 Setting the time of day 10 The timer 10 Cleaning your Baumatic cooker hood 11 The grease filters 11 Maintenance 12 - 15 Removing and cleaning the grease filters 12 Changing a light bulb 13 Fitting the carbon filter 14 - 15 Installation 16 - 23 Electrical connection 16 - 17 Before beginning installation 17 – 18 Positioning 18 - 19 Installing your cooker hood 19 - 23 Supplied installation components 20 Connecting to external ducting 20 Fitting the chimney 20 – 22 Completing the installation 23 Extraction mode or recirculation mode? 23 External ducting 23 Troubleshooting 24 - 25 Contact details 26

disconnect it from the power supply. Cut off and render any plug useless. Cut the cable off directly behind the appliance to prevent misuse. This should be undertaken by a competent person. CONFORMITY TO W.E.E.E. DIRECTIVE 4

Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the information contained in this booklet, please contact the Baumatic Advice Line. IMPORTANT: Any installation work must be carried out by a qualified electrician or competent person. o The hood must be installed in accordance with the installation instructions and all measurements followed. o If the cooker hood is installed for use above a gas appliance then the provision for ventilation must be in accordance with the Gas Safety Codes of Practice BS.6172, BS.5440 & BS.6891 (Natural Gas) and BS.5482 (LP Gas) 1994, the Gas Safety (Installation & Use) Regulations, the Building Regulations issued by the Department of the Environment, the Building Standards (Scotland) (Consolidated) Regulations issued by the Scottish Development Department. o It is dangerous to alter the specifications or to modify this product. Do not tamper with it or attempt to modify the appliance in any way. o When installing the hood, ensure that the following recommended distances are observed between the highest point on the hob top (including the burners) and the bottom of the cooker hood: ¾ Electric cookers: 700 mm ¾ Gas cookers: 700 mm ¾ Coal/ oil cookers: 800 mm IMPORTANT: DO NOT SET YOUR COOKER HOOD LESS THAN 700mm ABOVE YOUR COOKER. o When installed between adjoining wall cabinets, the cabinets must not overhang the hob. 5

you handle your appliance, especially during installation and cleaning. DO NOT CLEAN IN BEHIND THE GREASE FILTERS! o If the room where the cooker hood is to be used contains a fuel burning appliance such as a central heating boiler then its flue must be of the sealed or balanced flue type. o If other types of flue or appliances are fitted, ensure that there is an adequate supply of air in the room. o When the hood is being used in its extractor function, ensure that the ducting is fire retardant and that there are no bends sharper than 90 degrees as this will reduce the efficiency of the hood. o Ensure the ducting for the extractor function has the same diameter as the outlet hole all the way through. o Keep young children from using, playing with or tampering with the cooker hood. Older children and infirm persons should be supervised if they are using the cooker hood. o Your cooker hood is for domestic use only. o Please dispose of the packing material carefully – children are especially vulnerable to it. o Dirty oil is an even greater fire risk. o Always put lids on pots and pans when cooking on a gas cooker. o The manufacturer refuses to accept any responsibility for damages arising to the hood or it catching on fire, from a failure to observe the fire safety advice contained in this instruction booklet. 6

removing air from your room. Ensure that proper ventilation measures are being observed. o Note that it removes odours from your room, not steam. o Warning - Always ensure that the cooker hood has been disconnected from the power supply before carrying out any work on the hood, including replacing light bulbs. o Do not connect the ducting system of this appliance to any existing ventilation system which is being used for any other purpose. o Do not install above a cooker with a high level grill. o Never leave frying pans unattended during use as overheated fats and oils might catch fire. o The lights on this appliance should only be used during operation of the cooker hood. They should not be left on permanently and used as a lighting source. o The cooker hood should not be exposed to a direct heat source from the cooking device underneath it, i.e. naked flame from a gas burner or heat from electric hob zones without a pan on them. o Do not attempt to use the cooker hood if it is damaged in any way. Never attempt to use it without the grease filters fitted or if the filters are excessively greasy! o Never flambé cook under this cooker hood. THE MANUFACTURER DECLINES ALL RESPONSIBILITY IN THE EVENT OF FAILURE TO OBSERVE THE INSTRUCTIONS GIVEN HERE, FOR INSTALLATION, MAINTENANCE AND SUITABLE USE OF THE HOOD. 7

Congratulations on purchasing a Baumatic cooker hood! PRODUCT DIMENSIONS Height: 665 mm * – 1165 mm Width: 900 mm Depth: 600 mm DIMENSIONS OF CHIMNEY SECTION 270 mm x 285 mm o High extraction tangential motor o LCD display o Touch control operation o 3 Speeds o 2 Metallic grease filters o 4 Halogen lights o Extraction capacity: 1000 m³/hr o Optional extra: 1 x SQ2 Carbon filter required for recirculation mode * IMPORTANT: Please see the positioning instructions on pages 18 - 19 to obtain precise information on the height requirements for this product. 8

Before first use IMPORTANT: THIS PROCESS MUST BE FOLLOWED BEFORE THE COOKER HOOD IS USED FOR THE FIRST TIME. o You should use a good quality stainless steel cleaner and polish on ALL of the stainless steel areas of your cooker hood, before it is used for the first time. o This will help to leave a silicone water-resistant film to protect the stainless steel surfaces. To use your cooker hood o Make sure that it has been installed by a suitably qualified person, as per the information contained in Baumatic’s installation instructions. o Find the control panel, which is located in the middle of the canopy. o There are several buttons on the control panel, which perform separate functions. o Press the Add/ON button to switch the cooker hood on. The hood will start to run at its lowest speed. o The cooker hood has three operating speeds; low, medium and high. Use the Add/ON button to increase the speed and use the Dec/OFF button to decrease the speed that it is operating at. o The operating speed that you have selected will appear on the LCD display. o If you press the Dec/OFF button when the hood is operating at its lowest speed, then the hood will switch off. 9

IMPORTANT: IDEALLY YOU SHOULD SWITCH ON R etting the time of day o Press and hold the timer button, until the first two digits of the o Release the timer button, then use the Add/ON button and o Press the timer button again and the second two digits of the o Use the Add/ON button and Dec/OFF button to set the minute o Once the time of day is shown correctly on the display, press the he timer o You can use the cooker hood’s timer, to set the cooker hood to o You can get the cooker hood to countdown for the following No. of pushes of the timer Length of time (in minutes) switch the lights on, even if the hood is not operating. YOUR HOOD TEN MINUTES BEFORE YOU START TO COOK, OR AT THE VERY LEAST WHEN YOU BEGIN COOKING. YOU SHOULD ALSO RUN YOUR HOOD FO TEN MINUTES AFTER YOU HAVE FINISHED COOKING. S display start to flash. Dec/OFF button to set the hour time. display will start to flash. time. timer button for the third time to confirm it. T run for a particular period of time and then switch off. periods of time:- button the cooker hood will operate for 1 5 minutes 2 15 minutes 3 30 minutes 4 Timer function cancelled o Once you have set a countdown period, the cooker hood will o When the countdown time has been reached, 00:00 will appear and the cooker hood will stop running. start to countdown. The time remaining until the cooker hood shuts off will show on the display.

11 IMPORTANT: BEFORE CLEANING, ALWAYS ENSURE THAT YOU HAVE SWITCHED YOUR COOKER HOOD OFF AT THE OMNI-POLAR SWITCH, SET AT THE WALL FROM THE CABL E. the external parts of your cooker hood with mild liquid detergent and a new damp cloth. ive solvents or brushes. lish on ALL of the stainless steel areas of your cooker hood grid. uid detergents and a new damp cloth. irculation mode, then be sure to replace the carbon filter at the recommended interval e area above the grease filters. Cleaning o Clean o Never use abrasive powder, corros o You should use a good quality stainless steel cleaner and po o Never insert pointed objects into the motor’s protective o Only clean the control panel and grease filter grill with mild liq o If you are using the appliance in rec (see section on “Fitting the carbon filter”). A build up of greas could cause a fire hazard. o Never attempt to clean the The grease filters o Your cooker hood includes two grease filters which help to absorb grease particles to protect your kitchen & furniture from s may become inflammable if they become saturated with this greasy residue. s should be cleaned regularly. Depending on use, this should be done every 10-15 al REASE FILTERS IN A DISHWASHER. greasy residues. o The metallic filter o To prevent this fire hazard, the filter days or at least once a month, using hot water and norm washing-up detergent. o DO NOT WASH THE G

o First remove the grease filters by pulling down on the handle and ers in hot about an hour. Rinse it off thoroughly with hot water. Repeat the process if required. o Refit the grease filters once it has dried. o IMPORTANT: Let the grease filters dry thoroughly before refitting it in the cooker hood. pulling them away from the cooker hood. o Soak the grease filt water and washing up liquid for o o

13 IMPORTANT: BEFORE ATTEMPTING TO CHANGE AT YOU E COOKER HOOD FROM the grease filters (as described on page 12). bs ensure that they have cooled in t fixture which is inside the exposed section of the canopy. o Use a screwdriver to remove the glass cover that sits over the bulb. Unplug the light bulb that needs to be replaced and insert a new G4 20W (max) bulb. Then replace the glass cover. If the lights still do not work, make sure that the bulbs are fitted assistance. o Refit the grease filters. A LIGHT BULB, YOU MUST ENSURE TH HAVE DISCONNECTED TH YOUR MAINS SUPPLY. o Remove o Prior to touching the light bul down. o Find the bulb that requires replacement, you will find it located the ligh o IMPORTANT: Defective bulbs should be replaced immediately. o properly into their housings before you call for technical

the appliance is being used to be used in recirculation mode then it ers. This will help to absorb unpleasant dours caused by cooking. HE CARBON FILTER, YOU MUST YOU HAVE DISCONNECTED THE ) Remove the grease filters. 2) The line drawing above shows what you will see after removing the grease filters. fixing point in the top right hand corner (both indicated by arrows in the above drawing). F If is necessary to fit carbon filt o IMPORTANT: BEFORE ATTEMPTING TO FIT OR REMOVE T ENSURE THAT COOKER HOOD FROM YOUR MAINS SUPPLY. 1 o The carbon filter will be fitted over the motor casing hole and there is a

ke out the two screws at go through the fixing the t on it, must be above the fixing point, into the st be fully tightened. 4) After fitting the arbon d as in . he carbon filters should be replaced approximately every three of damage, or if you start to notice that oking smells are entering the kitchen through the upper vents. ta th point and then lower the carbon filter over the motor casing hole. o The corner with diagonal cut-ou positioned against the fixing point (as shown in the picture). o Retighten the two screws through carbon filter. These screws mu c filter, the underneath of the cooker hoo should appear the drawing opposite o Refit the grease filters. T months, if they show signs o c

voltage (V) and the frequency (Hz) indicated on ting he manufacturer declines all responsibility in the event of the installer iling to observe all the accident prevention regulations in force, hich are necessary for normal use and the regular operation of the OUR COOKER HOOD IS INTENDED FOR FITTED AND ATION. ble must be fitted upstream from the electrical connection, using an omni-polar switch with a contact distance of at least 3 mm. THE FUSE MUST BE RATED AT 3 nected by a competent person, using xed wiring via a double pole switched fused spur outlet. IMPORTANT: Before installation and usage read the rating plate are exactly the same as the voltage and frequency in your home. The ra plate can be found behind the grease filter. T fa w electric system. Electrical connection Y PERMANENT INSTALL o The cooker hood’s power ca AMPS. WARNING: THIS APPLIANCE MUST BE EARTHED. It should only be con fi fie o is a member of the N.I.C.E.I.C. and who will comply ith the I.E.E. and local regulations. The wires in the mains lead are f you only find two wires in the main’s lead (blue and brown), then (UK ONLY). We recommend that the appliance is connected by a quali electrician, wh d w coloured in accordance with the following UK code: Blue = Neutral, Brown = Live, Green/Yellow = Ground I neither must be connected to the earth terminal.

utral), or coloured black. l marked “L” (live), or coloured red. o Check that the product purchased is of a suitable size for the addition check whether there is an electrical socket available that will be accessible once the hood is , e od. y n. other materials, such as packets of screws, guarantees etc. These should be removed and kept for future s heir position, to provide easier access to the ceiling. If this is not possible, then a thick, protective covering should be at oker hood parts and fittings on it. ified technician must verify the suitability of the materials, in accordance with the type of ceiling. correspond with the coloured markings identifying the terminals in your spur box, please proceed as follows: o The blue wire must be connected to the terminal marked “N” (ne o The brown wire must be connected to the termina installation Before beginning chosen installation area. In mounted. If the product is going to be used in extraction mode then there should also be space to connect a ducting hose to th outside. o Carry out all necessary masonry work prior to the fitting of the cooker ho o Ensure that all electrical connections are carried out by a suitabl qualified perso o Check inside the product and ensure that there is no transit packaging or any use. o If possible, disconnect and move freestanding or slot-in cooker from t placed over the worktop, hob top or cooker. This will help to protect these surfaces from damage and debris. o Select a flat surface for assembling the cooker hood. Cover th surface with a protective covering and place all co o Wall plugs are provided to secure the hood to most types of ceilings. However a qual The ceiling must be strong enough to take the weight of the hood.

appliance is designed to be surface mounted only. on the cooker hood or chimney sections, to protect them during transit. = = Total height of the kitchen nd the hood m opy liance, you need to use the following formula: X = A – (B + C + 8 cm). alculated according to the height of the chimney sections. You must allow ns and o Remove any protective wrapping that has been put Positioning X Height of the appliance A B = Height of the worktop C = Distance between the hob a 8 c = Height of the hood can o To work out the height of the app o The overall height of the appliance should be c yourself sufficient space to make the electrical connectio connecting the ducting hose (if required).

height of 2.7 metres, othe u may encounter MPORTANT: Although the minimum height of the ppliance can be set at 665 mm. During the installation tion d WILL HAVE TO DECIDE BEFORE INSTALLING YOUR COOKER HOOD WHETHER TO USE SE o We re o people install this hood. eiling joists or joints between joists that are weight bearing. DO NOT hang this be able to withstand a weight of at least 40 kilograms. g MUST be at least 30 mm thick. underneath it. You cannot fit this product by securing it between your cooker hood in extraction mode, then you will need to make the necessary arrangements for the ducting, SHOULD BE CONNECTED TO YOUR MAINS SUPPLY AFTER rwise yo difficulties when installing the appliance. I a process you will need to move the lower chimney sec upwards, to allow you to attach the main body of the hoo to the framework. To achieve this you will require a vertical gap of no less than 1000 mm. Installing your cooker hood IMPORTANT: YOU IT IN EXTRACTION MODE OR RECIRCULATION MODE. PLEASE TURN TO PAGE 23 NOW TO UNDERSTAND THE DIFFERENCES BETWEEN THE TWO MODES. commend that tw o Your cooker hood should only be suspended from c hood from a suspended ceiling. o IMPORTANT: The ceiling MUST o IMPORTANT: The ceilin o It must be positioned at least 700 mm above the hob two cupboards. o If you are using before the rest of the installation. IMPORTANT: YOUR COOKER HOOD THE REST OF THE INSTALLATION PROCESS HAS BEEN COMPLETED.

1) Position the hanging plate on the eiling and then mark the position of the ging plate should be securely fixed to the ceiling, using . ceiling that you are fixing the hanging plate to, you may need to use 8 x expansion bolts (for c screw holes. o The han the 12 x ST6 (40 mm) screws o Depending on the surface of the concrete).

sing the 8 x M4 nuts and bolts with metal 3) Extend the angle bars to the required height nd then fix them in position using the 16 x M4 must have an overlap of AT LEAST 100 mm. 4) If your cooker hood is going to be used in xtraction mode, then you should connect the t. hanging plate, using the 4 x self tapping lower chimney section onto the angle bars and raise it until it sits just below i er chimney section in this position, to make sure that it does not drop down u washers. a nuts and bolts with metal washers. o IMPORTANT: The angle bars e ducting hose to the ceiling adaptor at this poin o Fix the upper chimney section to the screws. o Slide the the upper chimney section. ng hook to temporarily keep the low o Use the hang whilst fixing the main body of the hood to the angle bars.

xtraction mode, you should fit the spigot for ) If the glass canopy has not been pre- ssembled by the factory, then it should be 7) Lift the main body of the cooker hood onto e angle bar and then fix it into position using : This stage of the installation process MUST be olts MUST be securely tightened. ) If you are going to be using the hood in xtraction mode, you should fix the ducting connection must correspond to the electrical plate, oker hood. y selecting each speed and switching the light bulbs on and off. e the duct hose onto the main body of the cooker hood, using the 4 x M4 bolts, 6 a fixed to the top of the main body of the cooker hood at this stage. th the 16 x M4 bolts. o IMPORTANT completed by two people. o IMPORTANT: The 16 x M4 b 8 e hose to the spigot. o The electrical requirement noted on the rating which is placed inside the co The appliance should now be connected to the electrical supply. See page 16 – 17 for detailed information on the electrical connection. liance is operating correctly b o Check that the app

steel cleaner and polish on the stainless steel sections of the appliance. nce in recirculation mode, then you should now fit the carbon filter. See the “Fitting the carbon filter” r recirculation mode? o Remove the hanging hook and then slide the lower chimney section downwards, until it rests against the ma cooker hood. o Use a stainless o If you are using the applia section on pages 14 - 15. Extraction mode o What is t ion odes? timum performance from your cooker, the air will be taken ut of the room via external ducting. hood is too far from an outside all, this may not be possible. The only alternative is to recirculate the circulation mode stale air is taken via the grease filter, and passed hrough a charcoal filter for purification. The air then re-enters the eed one? using your cooker ood in recirculation mode, then a charcoal filter must be fitted in pigot to the top of the cooker hood, and then connect a 125 mm ducting hose to the coupling (please note that to a discharge outlet that is suitable for cooking vapours. It should ing and your discharge outlet should be 3 metres, with one 90 degree bend. maximum distance between the coupling and your discharge outlet is reduced by 1 metre. he difference between extraction and recirculat m To get op o Unfortunately if you live in a flat or the w air. In re t kitchen via an opening in the hood. What is a charcoal filter and do I n All cooker hoods have a grease filter but if you are h addition to the grease filter. External ducting o Connect the s the ducting hose is not supplied with the appliance). o The other end of the ducting hose should be connected have a cross section of at least 150 cm². o The maximum distance between the coupl o For each additional 90 degree bend that is made, the

tacting Baumatic Customer Care, please efer to the checklist below. not start. e e electricity supply o Check that the fan speed control is set correctly. My cooker hood is not working effectively. e o The grease filters are dirty and require cleaning. The kitchen is not well ventilated enough. o If the hood is set up for recirculation mode, check that the ting cked. ring operation. e o Turn off the hob and then wait for the safety cut-out device to ety cut-out device will frequently trip. Your cooker hood may become damaged if the safety cut-out device is tripped off y. properly, before con r My cooker hood will ck that the hood is connected to th o Ch fan speed is not set high enough o Th o carbon filters do not need replacing. o If the hood is set up for extraction mode, check that the duc hose and discharge outlet are not blo My cooker hood has switched off du safety cut-out device has been tripped. o Th reset. o IMPORTANT: If you have installed your cooker hood too low, the saf frequently. o The timer has been accidentally set to switch the cooker hood automaticall 24

from your mains supply and then contact Baumatic Customer Care on telephone number NCE t is t at the problem is not the result of an ppliance fault, then you may be liable for the cost of the call out harge. t an engineer is concerned that damage will be caused the appliance or your kitchen, then he will not complete a the appliance, like plinths. Or any installation other han the one specified by Baumatic Ltd. has been completed. IMPORTANT: If your appliance appears not to be opera (0118) 933 6911. DO NOT ATTEMPT TO REPAIR THE APPLIA YOURSELF. Please note th under guaran at if an engineer is asked to attend whilst the produc ee and finds th a c The appliance must be accessible for the engineer to perform any necessary repair. If your appliance is installed in such a way tha to repair. This includes situations where appliances have been tiled in, sealed in with sealant, have wooden obstructions placed in front of t Please refer to the conditions of guarantee that appear on the warranty card that you receive with the appliance.

eading, Berkshire e R RG2 0QX United Kingdom Sales Telephon (0118) 933 6900 Sales Fax ustomer Care Telephone (0118) 931 0035 C ax (0118) 933 6911 Customer Care F 9124 e (0118) 986 Spares Telephon phone (01235) 437244 Advice Line Tele (0118) 933 6933 E-mail: [email protected] o.uk co.uk [email protected] [email protected] spares@baumatic. te Website: www.baumatic.co.uk Republic of Ireland 01- 6266 798 zech Republic aumatic CR spol s.r.o. mperova 495 6215, Librec zech Republic 420 800 185 263 ww.baumatic.cz lovak Republic aumatic Slovakia, s.r.o. kultetyho 1 618 ermany nderstrasse 9 ermany taly L. ia Caltana 129 ego (Padova), 35011 ww.baumatic.it olland .V. rindzuigerstraat 22 S ALMERE www.baumatic.nl C B A 4 C + w S B S 831 04 Bratislava 3 Slovakia +421 255 640 G Baumatic Gmbh Ja Mannheim, 68199 G +4962 112 9190 www.baumatic.de I Baumatic Italia S.R. V Campodars Italy +3904 9920 2297 w H Baumatic Benelux B G 1333 M The Netherlands +3136 549 1555