Baumatic CAN52.4ME Instruction Manual

CAN52.4ME 52 cm CAN75.3SS 75 cm Canopy Hood NOTE: This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is easily available for future reference; for you or any person not familiar with the operation of the appliance. GS 02/01/13 2

5 – 7 Specifications of your cooker hood 8 – 10 CAN52.4ME 8 CAN75.3SS 9 - 10 Using your Baumatic cooker hood 10 - 11 Before first use 10 To use your cooker hood 10 - 11 Cleaning your Baumatic cooker hood 11 – 12 General cleaning 11 The grease filter 12 Maintenance 12 – 16 Removing and cleaning the grease filter 12 - 13 Changing a light bulb 13 - 14 Fitting the carbon filters 14 - 16 Installation 16 - 21 Electrical connection 17 Before beginning installation 17 - 18 Installing your cooker hood 18 - 20 Connecting to external ducting 20 - 21 Completing the installation 21 Extraction mode or recirculation mode? 21 - 22 Troubleshooting 22 – 24 Baumatic consumables 25 Contact details 26

disconnect it from the power supply. Cut off and render any plug useless. Cut the cable off directly behind the appliance to prevent misuse. This should be undertaken by a competent person. o The packaging materials that Baumatic uses are environmentally friendly and can be recycled. o Please discard all packaging material with due regard for the environment. 4

Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the information contained in this booklet, please contact the Baumatic Customer Care Department. IMPORTANT: Any installation work must be carried out by a qualified electrician or competent person. o The hood must be installed in accordance with the installation instructions and all measurements followed. o If the cooker hood is installed for use above a gas appliance then the provision for ventilation must be in accordance with the Gas Safety Codes of Practice BS.6172, BS.5440 & BS.6891 (Natural Gas) and BS.5482 (LP Gas) 1994, the Gas Safety (Installation & Use) Regulations, the Building Regulations issued by the Department of the Environment, the Building Standards (Scotland) (Consolidated) Regulations issued by the Scottish Development Department. o It is dangerous to alter the specifications or to modify this product. Do not tamper with it or attempt to modify the appliance in any way. o When installing the hood, ensure that the following recommended distances are observed between the highest point on the hob top (including the burners) and the bottom of the cooker hood:  Electric cookers: 700 mm  Gas cookers: 700 mm  Coal/ oil cookers: 800 mm IMPORTANT: DO NOT SET YOUR COOKER HOOD LESS THAN 700mm ABOVE YOUR COOKER. o When installed between adjoining wall cabinets, the cabinets must not overhang the hob. 5

you handle your appliance, especially during installation and cleaning. DO NOT CLEAN IN BEHIND THE GREASE FILTERS! o If the room where the cooker hood is to be used contains a fuel burning appliance such as a central heating boiler then its flue must be of the sealed or balanced flue type. o If other types of flue or appliances are fitted, ensure that there is an adequate supply of air in the room. o When the hood is being used in its extractor function, ensure that the ducting is fire retardant and that there are no bends sharper than 90 degrees as this will reduce the efficiency of the hood. o Ensure the ducting for the extractor function has the same diameter as the outlet hole all the way through. o Keep young children from using, playing with or tampering with the cooker hood. Older children and infirm persons should be supervised if they are using the cooker hood. o Your cooker hood is for domestic use only. o Please dispose of the packing material carefully – children are especially vulnerable to it. o Dirty oil is an even greater fire risk. o Always put lids on pots and pans when cooking on a gas cooker. o The manufacturer refuses to accept any responsibility for damages arising to the hood or it catching on fire, from a failure to observe the fire safety advice contained in this instruction booklet. 6

removing air from your room. Ensure that proper ventilation measures are being observed. o Note that it removes odours from your room, not steam. o Warning - Always ensure that the cooker hood has been disconnected from the power supply before carrying out any work on the hood, including replacing light bulbs. o Do not connect the ducting system of this appliance to any existing ventilation system which is being used for any other purpose. o Do not install above a cooker with a high level grill. o Never leave frying pans unattended during use as overheated fats and oils might catch fire. o The cooker hood should not be exposed to a direct heat source from the cooking device underneath it, i.e. naked flame from a gas burner or heat from electric hob zones without a pan on them. o Do not attempt to use the cooker hood if it is damaged in any way. Never attempt to use it without the grease filters fitted or if the filters are excessively greasy! o Never flambé cook under this cooker hood. o The lights on this appliance should only be used during operation of the cooker hood. They should not be left on permanently and used as a lighting source. THE MANUFACTURER DECLINES ALL RESPONSIBILITY IN THE EVENT OF FAILURE TO OBSERVE THE INSTRUCTIONS GIVEN HERE, FOR INSTALLATION, MAINTENANCE AND SUITABLE USE OF THE HOOD. 7

CAN52.4ME Product dimensions Height: 162 mm Width: 520 mm Depth: 296 mm Your canopy hood is fitted with: o Slider control operation o Integrated axial motor o 3 speeds o 1 washable aluminium grease filter o Non-return airflow flap o 2 halogen lights o Noise level: 45 / 50 / 55 dB Extraction capacity: 250 m³ / hr Optional extras: 1 pair ST1 carbon filters for air recirculation mode DK5 1 metre length ducting kit 125 mm Ø DK10 3 metre length ducting kit 125 mm Ø with flat channelling included. 8

o Slider control operation o Integrated axial motor o 3 speeds o 1 washable aluminium grease filter o Non-return airflow flap o 2 halogen lights o Noise level: 61 / 65 / 68 dB Extraction capacity: 750 m³/hr Optional extras: 1 pair S1 Carbon filters for air recirculation mode DK5 1 metre length ducting kit 125 mm Ø DK10 3 metre length ducting kit 125 mm Ø with flat channelling included. All of the optional extras are available from the Baumatic Spares Department. 9

Before first use IMPORTANT: THIS PROCESS MUST BE FOLLOWED BEFORE THE COOKER HOOD IS USED FOR THE FIRST TIME. o You should use a good quality stainless steel cleaner on ALL of the stainless steel areas of your cooker hood, before it is used for the first time. o This will help to leave a silicone water-resistant film to protect the stainless steel surfaces. To use your cooker hood o Make sure that it has been installed by a suitably qualified person, as per the information contained in Baumatic’s installation instructions. o Find the control panel, which is located at the front right of the canopy. o There are two sliders on the control panel, which perform separate functions. 1) Light control. The light can be used even when the motor is OFF. 0 = Light OFF 1 = Light ON 2) Motor speed control. = Low speed = Medium speed = High speed 10

YOUR HOOD TEN MINUTES BEFORE YOU START TO COOK, OR AT THE VERY LEAST WHEN YOU BEGIN COOKING. YOU SHOULD ALSO RUN YOUR HOOD FOR TEN MINUTES AFTER YOU HAVE FINISHED COOKING. Cleaning your cooker hood IMPORTANT: BEFORE CLEANING, ALWAYS ENSURE THAT YOU HAVE SWITCHED YOUR COOKER HOOD OFF AT THE OMNI-POLAR SWITCH, SET AT THE WALL FROM THE CABLE. Cleaning o Clean the external parts of your cooker hood with mild liquid detergent and a new damp cloth. o Never use abrasive powder, corrosive solvents or brushes. o Never insert pointed objects into the motor’s protective grid. o Only clean the control panel and grease filter grill with mild liquid detergents and a new damp cloth. o If you are using the appliance in recirculation mode, then be sure to replace the carbon filters at the recommended interval (see section on “Fitting the carbon filter”). A build up of grease could cause a fire hazard. o Never attempt to clean the area above the grease filter. o IMPORTANT: You should regularly use a good quality stainless steel cleaner to maintain the shine and finish on the stainless steel areas of your cooker hood. o This will help to leave a silicone water-resistant film to protect the stainless steel surfaces and keep them in good condition for the life of the product. 11

o Your cooker hood includes a grease filter which helps to absorb grease particles to protect your kitchen and furniture from greasy residues. o The metallic filter may become flammable if it becomes saturated with greasy residue. o To prevent this fire hazard, the filter should be cleaned regularly. Depending on use, this should be done every 10-15 days or at least once a month, using hot water and normal washing-up detergent. o DO NOT WASH THE GREASE FILTER IN A DISHWASHER. Maintenance Removing and cleaning the grease filter o First remove the grease filters by pulling down on the handle and pulling them away from the cooker hood. o Soak the grease filter in hot water and washing up liquid for about an hour. o Rinse it off thoroughly with hot water. 12 o Repeat the process if required.

has dried. o IMPORTANT: Let the grease filter dry thoroughly before refitting it in the cooker hood. Changing a light bulb IMPORTANT: BEFORE ATTEMPTING TO CHANGE A LIGHT BULB, YOU MUST ENSURE THAT YOU HAVE DISCONNECTED THE COOKER HOOD FROM YOUR MAINS SUPPLY. 13 described on page 12). at they have cooled down. d it located in the light fixture which the canopy. o Press gently on the underside of the bulb that needs to be replaced and twist anticlockwise to release. o Remove the grease filter (as o Prior to touching the light bulbs ensure th o Find the bulb that requires replacement, you will fin is inside the exposed section of

are fitted before you call for technical o Refit the grease filter. e b FORE ATTEMPTING TO FIT OR REMOVE THE CARBON FILTERS, YOU MUST o You will find that one filter will attach over the front of the fan e replaced at least every four months depending on usage to allow normal operation when E (1 x pair ST1 carbon filters) o Remove the grease filters. o Insert a new identical 40W (max) bulb. o IMPORTAN o If the lights still do no properly into their housings assistance. t work, make sure that the bulbs Fitting the carbon filter If the applianc necessary to a odours caused is going to be used in recirculation mode then it is fit a carbon filter. This will help to absorb unpleasant y cooking. IMPORTANT: BE ENSURE THAT YOU HAVE DISCONNECTED THE COOKER HOOD FROM YOUR MAINS SUPPLY. motor. The active carbon filter must b in recirculation mode. CAN52.4M

pins that are located at the end of the motor. ) Turn the carbon filter clockwise until you feel it latch nto the motor’s sides. grease filters. w the steps outlined above and turn the carbon filter anti-clockwise to unlatch it from the motor. CAN75.3SS (1 x pair S1 carbon filters) ) Remove the grease filters (as described reviously). ) Hook the carbon filter over he pins that are located at the nd of the motor. 3 o 4) Replace the o When replacing the carbon filter, follo 1 p 2 t e

until you feel it click into place. o Repeat this process for the second carbon filter. You need to o Refit the grease filters. o The carbon filters should be replaced every 3 - 6 months or if they show place a carbon filter at either end of the motor. signs of damage. Installation IMPORTANT: Before installation read all the instructions and make sure that the voltage (V) and the frequency (Hz) indicated on the rating plate are exactly the same as the voltage and frequency in your home. The rating plate can be found behind the grease filters. The manufacturer declines all responsibility in the event of the installer iling to observe all the accident prevention regulations in force, hich are necessary for normal use and the regular operation of the lectric system. fa w e

ARNING: THIS APPLIANCE MUST BE EARTHED. It E YOUR COOKER HOOD IS INTENDED FOR FITTED AND PERMANENT INSTALLATION. electrical connection, using an omni-polar switch with distance of at least 3 mm. THE FUSE MUST BE RA AMPS. a contact TED AT 3 W should only be connected by a competent person, using fixed wiring via a double pole switched fused spur outlet. (UK ONLY). We recommend that the appliance is connected by a qualified ill comply ith the I.E.E. and local regulations. The wires in the mains lead are lue = Neutral, Brown = Live, Green/Yellow = Ground erminal. in your spur box, please proceed as follows: black. o The brown wire must be connected to the stallation area. In addition check whether there is an electrical socket available that will be accessible once the hood is uld also be space to connect a ducting hose to the outside. ssary masonry work prior to the fitting of the cooker hood. electrician, who is a member of the N.I.C.E.I.C. and who w w coloured in accordance with the following UK code: B If you only find two wires in the main’s lead (blue and brown), then neither must be connected to the earth t o As the colo correspond urs of the wires in the appliance’s mains lead may not with the coloured markings identifying the terminals o The blue wire must be connected to the terminal marked “N” (neutral), or coloured terminal marked “L” (live), or coloured red. Before beginning installation o Check that the product purchased is of a suitable size for the chosen in mounted. If the product is going to be used in extraction mode, then there sho o Carry out all nece

qualified person. 18 inside the product and ensure that there is no transit packaging or any other materials, such as packets of screws, wall and ceiling. If this is not possible, then a thick, protective covering o Select a flat surface for assembling the cooker hood. Cover that o Do not tile, grout or silicone this appliance to the wall or is designed to be surface mounted only. y CTION MODE OR RECIRCULATION MODE. PLEASE TURN TO PAGE 21-22 NOW TO WEEN THESE TWO MODES. d that two people install this hood. o It must be positioned at least 700 mm above the hob IMPORTANT: YOUR COOKER HOOD SHOULD BE CONNECTED TER o Before commencing installation of the cooker hood the grease filter should be removed. o Check guarantees etc. These should be removed and kept for future use. o If possible, disconnect and move freestanding or slot-in cookers from their position, to provide easier access to the rear should be placed over the worktop, hob top or cooker. This will help to protect these surfaces from damage and debris. surface with a protective covering and place all cooker hood parts and fittings on it. cabinetry. This appliance Installing our cooker hood IMPORTANT: YOU WILL HAVE TO DECIDE BEFORE INSTALLING YOUR COOKER HOOD WHETHER TO USE IT IN EXTRA UNDERSTAND THE DIFFERENCES BET o We recommen o Your cooker hood should only be fitted into the underside of a kitchen unit. underneath it. You cannot fit this product by securing it between two cupboards. TO YOUR MAINS SUPPLY AF THE REST OF THE INSTALLATION PROCESS HAS BEEN COMPLETED. 1) Remove the metal grease filter (A).

ut must be of the dimensions shown in the drawing below. CAN52.4ME 2) Create an opening in the underneath of the kitch o CAN75.3SS o IMPORTANT: If you are going to connect your cooker hood to external ducting, then you must complete the steps listed in the “Connecting to external ducting” section before carrying on with or frame (B) to the hood and unscrew the 2 lights. nsure that the two support clips on either side of the hood are set to ker hood towards the cut-out that you made in step 2. eed the electrical cable through the hole that you made in step 3. the rest of the installation (this information can be found on page 20). 3) Make a hole in the inside of the kitchen unit for the electrical cable to feed through. Remove the 2 screws (4 screws for CAN52.4ME) securing the extract E accommodate the thickness of the mounting surface, by adjusting the clip via the screw. 4) Lift the coo F

e pre-drilled holes in the outer frame of the hood, into the kitchen unit. Then replace using the 2 screws (4 screws for CAN52.4ME) (B) and reattach the 2 lights. o Refit the grease filter. utlet should have a cross section of at least 150 cm² (please note that the ducting hose is not supplied with the tance between the coupling and your discharge outlet should be 3 metres, with one 90 degree bend. For each Before fixing the cooker hood into the kitchen unit, you should the ducting hose to the coupling in the top of the cooker hood. IMPORTANT: Do not connect the electrical cable to the mains supply at this stage. 5 If you are connecting the cooker hood to external ducting, then secure the ducting hose to the coupling on the appliance. o One person should support the hood. The other person should fully tighten the support screws through th the extractor frame Connecting to external ducting o Connect the coupling to the top of the cooker hood, using two of the smaller screws provided. o Connect a Ø125 mm ducting hose to a discharge outlet that is suitable for cooking vapours. o The discharge o appliance but one can be obtained from the Baumatic Spares Department). o The maximum dis additional 90 degree bend, the maximum distance is reduced by a further metre. o connect the other end of

should now fit the two carbon filters. See the “Fitting the carbon pliance should now be connected to the electrical supply. See page 17 for detailed information on the the appliance is operating correctly by selecting each speed and switching the light bulbs on and off. Extraction mode or recirculation mode? Completing the installation o If you are setting the appliance filters” section on pages 14-16. o The electrical connection must correspond to the electrical requirement noted on the rating plate, which is placed inside the cooker hood. The ap ele ctrical connection. o Refit the grease filter and then switch on the mains supply to the appliance. Check that ING YOUR COOKER HOOD WHETHER TO USE IN EXTRACTION MODE OR RECIRCULATION hat is the difference between extraction and recirculation extraction mode, the stale air will be taken via the grease filter and via the grease filter, and passed rough a charcoal filter for purification. The air then re-enters the or optimum performance, we recommend that the cooker hood is rtunately if you live in a flat or the hood is too far from an outside all, this may not be possible. The only alternative is to recirculate the ir. IMPORTANT: YOU WILL HAVE TO DECIDE BEFORE INSTALL IT MODE. W modes? In out of the room via external ducting. In recirculation mode stale air is taken th kitchen via an opening in the hood. F used in extraction mode and connected to external ducting. Unfo w a

a grea mode, ddition to the grease filter. All cooker hoods have hood in recirculation but if you are using your cooker arcoal filters must be fitted in a Troubleshooting IMPORT properl ANT: If your cooker hood appe e Custome ars not to be operating r Care Department, o Check that the hood is conne whether you have selected any of the fan speeds. o y please refer to the table below. , before contacting th My cooker hood will not start. cted to the power supply and My cooker hood is not working effectively. o Check that fan speed is set to an appropriate setting. Check that the grease filter is not dirty and if it requires cleaning.

r o If the hood is set up for extraction mode, check that the ducting n, due to the extraction capacity of the cooker hood. O NOT MAKE ANY ATTEMPT TO REPAIR THE APPLIANCE o ca bon filters do not need to be replaced. hose and discharge outlet are not blocked. My cooker hood is noisy and/or vibrating. o Check whether the installation has been completed as per the instruction booklet. o It is normal to get a certain amount of noise and vibratio D YOURSELF. IF THE APPLIANCE IS STILL NOT OPERATING CORRECTLY, PLEASE CONTACT THE CUSTOMER CARE DEPARTMENT ON TELEPHONE NUMBER (0118) 933 6911.

IMPORTANT: If your appliance appears not operating correctly, then you should disconn to be ect it from your mains supply and then contact YOURSELF. a ve been tiled in, lease refer to the conditions of guarantee that appear on the arranty card that you receive with the appliance. MPORTANT: Baumatic Ltd. operates a policy of continuous provement and reserves the right to adjust and modify its roducts without prior notification. Baumatic Customer Care on telephone number (0118) 933 6911. DO NOT ATTEMPT TO REPAIR THE APPLIANCE Please note that if an engineer is asked to attend whilst the product is under guarantee and finds that the problem is not the result of an appliance fault, then you may be liable for the cost of the call out harge. c The appliance must be accessible for the engineer to perform any necessary repair. If your appliance is installed in such a way that an engineer is concerned that damage will be caused o the appliance or your kitchen, then they will not complete t repair. his includes situations where appliances ha T sealed in with sealant, have wooden obstructions placed in front of the appliance, like plinths. Or any installation other than the one specified by Baumatic Ltd. has been completed. P w I im p 24

rs (200g) ml) o BC008 Microwave Cover o order a Baumatic consumable product please call 0123 5437 244 o BC002 Descaler for Washing Machines and Dishwashe o BC003 Ceramic Hob Cleaner (250ml) o BC004 Oven Cleaner (250 o BC005 Stainless Steel Cleaner and Protector (250ml) o BC007 E-Cloth – General Purpose Cloth T nd quote the product code. You can also order online from shop.baumatic.co.uk a e

6 Bennet Road, Reading, Berkshire Reading, Berkshire RG2 0QX RG2 0QX United Kingdom United Kingdom Sales Telephone Sales Telephone (0118) 933 6900 Sales Fax (0118) 931 0035 Customer Care Telephone 3 6911 (0118) 93 Customer Care Fax (0118) 986 9124 Spares Telephone (01235) 437244 Advice Line Telephone 6933 -mail: (0118) 933 E atic.co.uk [email protected] .uk sales@baum [email protected] s [email protected] Website: www.baumatic.co.uk Facebook: www.facebook.com/baumatic.uk epublic of Ireland ervice Telephone R S -890 812 724 pares Telephone 1 S 91 756 771 aumatic CR s.r.o. c 577 200 ww.baumatic.cz aumatic Slovakia, s.r.o. 4 a - Staré Mesto 8 ww.baumatic.sk aumatic Gmbh r.10-12 49 (0) 5223 99408 0 taly Italia S.R.L. sego (PD) 97 ww.baumatic.it Baumatic Benelux B.V. Dukdalfweg 15d 1332 BH ALMERE Nederland +31(0)36 549 1555 www.baumatic.nl 0 Czech Republic B Lípovà 665 460 01 Liberec 4 Czech Republi +420 483 w Slovakia B Panenská 3 811 03 Bratislav Slovakia +421 255 640 61 w Germany B Bachst D-32 257 Bünde Deutschland + www.baumatic.de I Baumatic Via Galvani N.3 35011 Campodar +3904 9920 22 w Holland