Lancom AirLancer ON-T360ag Mounting Instructions

In the case of wall mounting, attach the antenna bracket to the wall with the enclosed bolts. You may need to drill the holes first and insert dowels. Attaching the antenna bracket by pole mounting In the case of pole mounting, use screw clamps to attach the antenna bracket directly to the pole. Attaching the antenna arm to the antenna When attaching the antenna arm to the antenna, please ensure that there is a close fit between them. Make use of the pin on the antenna arm and the matching recess in the antenna. Finally, use the locking screw to secure the antenna arm to the antenna. Important Mounting the antenna upside down If the antenna will be mounted outdoors and with the cables exiting upwards, it is essential to have a good seal by sticking the insulation disk to the antenna before attaching it to the antenna arm.

The antenna is attached to the antenna bracket by means of the antenna arm. To do this, place the antenna-arm joint socket onto the joint head of the antenna bracket. Tighten this joint with the wing screw or hexagon socket screw supplied. Whichever screw you use, please be sure to use the washer supplied. Attaching the antenna to a suspended ceiling This requires a 3-cm diameter hole in the suspended ceiling. First stick the insulation disk to the antenna. This acts as a washer and protects the ceiling and the antenna. Insert the cables and the screw thread through the hole in the ceiling. Then screw the locking screw onto the screw thread and tighten it. Important Working responsibly with high frequencies The AirLancer ON-T360ag meets the requirements of the R&TT directives 1995/5/EC and the FCC & ARPANSA regulations. To ensure compliance with these requirements, a minimum distance of 20 cm must be maintained between the antenna and the human body when operating the antenna. Important Electrical and electronic equipment law In the interests of recycling, please do not dispose of electrical and electronic waste in your household garbage. Ensure that your electrical and electronic waste is disposed of in accordance with the regulations in your country.

Antenna cables are sensitive RF cables. During installation it is important that the cables are not creased, and bent as little as possible, otherwise the antenna will suffer a loss of performance. Do not coil the antenna cable in tight loops. Important Antenna gain and terminating unused antenna connectors on the access point It is essential for unused antenna connectors on the access point to be terminated with the supplied rod antenna. The terminating resistor supplied with the adapter AirLancer AN-RPSMA-NJ is suitable for use with indoor access points. In addition, you must disable the unused antenna connectors in LCOS (changing the antenna grouping of the respective WLAN module), and configure the antenna gain of the antenna. The settings can be found in LANconfig at: Configuration > Wireless LAN > General > Physical WLAN settings > Radio Operating mode 2x2 MIMO & 1x1 MIMO Apart from its standard operation as a 3x3 MIMO antenna, this antenna can also be used by two WLAN modules operating in two different frequency ranges. This is done by connecting one of the connectors to one WLAN module and the other two connectors to the other WLAN module. As the AirLancer ON-T360ag has antenna segments that are aligned equally to one another, you are free to choose your arrangement. Please note that in this operating mode at least one antenna connector of the access point will be unused and has to be terminated. WLAN 1 5 GHz / 2x2 MIMO WLAN 1 5 GHz / 2x2 MIMO WLAN 2 2,4 GHz / 1x1 MIMO Surge Arrester AirLancer SN-ANT (not included)

owners. Subject to change without notice. No liability for technical errors and/or omissions. Technical details Frequency range 2400 - 2500 MHz, 4900 - 5900 MHz Antenna characteristics Radiation characteristics horizontal (2.4 GHz) 360° vertical (2.4 GHz) 25° horizontal (5 GHz) 360° vertical (5 GHz) 15° Recommended use Hotspot, coverage of open spaces VSWR 2.0:1 max. Gain 2.4 GHz 5 dbi max. 5 GHz 7 dbi max. Mechanical details Size 26 x 16 cm (height x diameter) Weight 950 g Temperature range -30°C to 70°C Color light grey Material UV-resistant plastic Mounting options Wall, pole, and ceiling mounting Cables, connectors 3 x 91.4 cm UV-resistant RG58 cable with N-plug connector Item Warranty 2 years for AirLancer and accessories Item number 61242 Package content Antenna, insulation disk, antenna arm, antenna bracket, locking screw, fastening bolts (2x wall mounting, hexagon socket screw/wing screw with washer to connect antenna arm to antenna bracket), Quick Reference Guide 2400 MHz 2500 MHz 5150 MHz 5400 MHz 5900 MHz -30 -25 -20 -15 -10 -5 0 5 10 0 30 60 90 120 150 180 210 240 270 300 330 2400 Mhz 2500 Mhz 5150 Mhz 5400 Mhz 5900 Mhz -30 -25 -20 -15 -10 -5 0 5 0 30 60 90 120 150 180 210 240 270 300 330 2400 Mhz 2500 Mhz 5150 Mhz 5400 Mhz 5900 Mhz 2.4 & 5 GHz h-plane 2.4 & 5 GHz e-plane