Da-Lite Cosmopolitan Electrol Instruction Book

3100 North Detroit Street Post Office Box 137 Warsaw, Indiana 46581-0137 Phone: 574-267-8101 800-622-3737 Fax: 574-267-7804 Toll Free Fax: 877-325-4832 www.da-lite.com e-mail: [email protected] POWER PRESENTATION PRODUCTS The In Instruction Book for COSMOPOLITAN® ELECTROL® For Sizes Up To 9'x12'

Flush against wall; Suspended from ceiling (use extension brackets); and Recessed above ceiling. NOTE: Under no circumstances should unit be completely sealed in recessed installation. Allow access for service. Picture surface is centered in case. Case extends 4" beyond surface on either end. Do not attach anything to screen slat rod or bottom fabric pocket. 1. Make sure screen is level. Use a carpenter’s level and plumb level. CAUTION! Do not cut wrapping paper or tape with knife or any sharp tool. Remove by hand. 2. Remove tape and rubber bands from slat pocket. 3. Install electrical hook up that applies to your unit. Make sure to review your Electrical Installation Checklists and wiring diagrams (included) for either 120 volt switch, 220/240 volt switch, or low voltage control. ▲! 1. Carefully unpack screen and remove outer wrapping from case. 2. Do not remove black tape or rubber bands from slat pocket. 3. Always handle screen in upright position. FIGURE 1 CEILING HANGING PICTURE SURFACE PICTURE SURFACE PICTURE SURFACE WALL MOUNTED CONCEALED (ALLOW ROOM FOR ACCESS) USE NO. 6 BRACKETS TO HANG BEHIND BEAM OR VALANCE PICTURE SURFACE IMPORTANT SAFETY INSTRUCTIONS When using your video equipment, basic safety precautions should always be followed, including the following: 1. Read and understand all instructions before using. 2. Position the cord so that it will not be tripped over, pulled, or contact hot surfaces. 3. If an extension cord is necessary, a cord with a current rating at least equal to that of the appliance should be used. Cords rated for less amperage than the appliance may overheat. 4. To reduce the risk of electric shock, do not disassemble this appliance. Contact an authorized service dealer when repair work is required. Incorrect reassembly can cause electric shock when the appliance is used subsequently. 5. The use of an accessory attachment not recommended by the manufacturer may cause a risk of fire, electric shock, or injury to persons. SAVE THESE INSTRUCTIONS

A FABRIC HEIGHT x WIDTH AS ORDERED, UP TO 12 FEET x 12 FEET. 3/8" DIAMETER FOR CEILING INSTALLATION ENCLOSURE COVER 7/8" DIAMETER OPENING FOR ELECTRICAL FITTINGS PICTURE SURFACE 3/4" DIAMETER HOLE FOR WALL INSTALLATION Overall length A=fabric width + 8". Length B is the distance between wall mounting holes at back of end caps and is the fabric width + 6-1/2". B 4" 4" 4-5/8" 1-7/8" 13/32" 5-7/8" 1" 15/16" FIGURE 2 MOTOR END

adjusted at DA-LITE. Should it be necessary to adjust for more or less picture drop (viewing area), proceed in the following manner: NOTE: Use a screwdriver or allen wrench to make adjustments. SETTING THE DOWN LIMIT POSITION TO REDUCE SCREEN DROP: Turn the white limit switch screw clockwise to decrease the amount of screen drop. Run the screen down to test the stop position. If the screen drops too far, raise the screen about one foot and adjust the limit switch again. Repeat until the desired position is set. TO INCREASE SCREEN DROP: Turn the white limit switch screw counterclockwise to increase the amount of screen drop. Run the screen down to test the stop position. If the screen does not drop enough, raise the screen about one foot and adjust the limit switch again. Repeat until the desired position is set. Do not adjust for more drop than what was ordered. At least 1-1/2 wraps of fabric must remain on the roller. SETTING THE UP LIMIT POSITION CAUTION: Do not allow the slat bar to wrap over the top of the roller when the screen is rolling into the case. The screen could be damaged. SCREEN TRAVELS INTO CASE TOO FAR: Turn the black limit switch screw clockwise to decrease the amount of travel. Run the screen up to test the stop position. If the screen does not stop properly, lower the screen about one foot and turn the limit switch again. Repeat until the desired position is set. SCREEN DOES NOT TRAVEL FAR ENOUGH INTO CASE: Turn the black limit switch screw counterclockwise to increase the amount of up travel. Run the screen up to test the stop position. If more travel is desired, lower the screen about one foot and adjust the limit switch again. Repeat until the desired position is set. ▲! 3 SCREEN ADJUSTMENT FOR 120V SCREENS WITHOUT A BUILT-IN LOW VOLTAGE CONTROL FIGURE 3 COSMOPOLITAN® ELECTROL® INSTALLATION WIRING ENCLOSURE COVER UP BLACK LIMIT SWITCH ADJUSTMENT AND DOWN WHITE LIMIT SWITCH ADJUSTMENT TO JUNCTION BOX, MOUNTED IN SCREEN CASE, IN WHICH INTERNAL WIRING TERMINATES IN WHITE, BLACK AND RED LEADS IN MULTIPLE CONTROL INSTALLATIONS THIS SWITCH IS REPLACED BY THE LOW VOLTAGE CONTROL, OPERATED FROM PUSH BUTTON STATIONS. OPERATING SWITCH AND PLATE FURNISHED WITH SCREEN. (SPDT WITH CENTER OFF) SIDE VIEW OF SWITCH AND BOX THIS SWITCH CANNOT BE USED WITH LVC. NOTE: A single switch cannot be used to operate more than one screen. Contact the factory for further information. DOWN BLACK BLACK UP WHITE RED DOWN AC HOT OFF COMMON WHITE BLACK WITH YELLOW UP RED ROCKER SWITCH AC COMMON 120 V. 60 HZ. 2.5 MAX. AMP 120V WIRING DIAGRAM

WIRING DIAGRAM IN MULTIPLE CONTROL INSTALLATIONS THIS SWITCH IS REPLACED BY THE LOW VOLTAGE CONTROL, OPERATED FROM PUSH BUTTON STATIONS. OPERATING SWITCH AND PLATE FURNISHED WITH SCREEN. NOTE: A single switch cannot be used to operate more than one screen. Contact the factory for further information. BLACK (UP) UP DOWN BROWN AC HOT OFF ROCKER SWITCH BLUE AC COMMON 220/240 V. AC 50 HZ. 2 AMP MAX. BROWN (DOWN) BLUE (COMMON) BROWN /YELLOW JUNCTION BOX BLUE JUMPER WIRE REAR VIEW OF DPDT, WITH CENTER OFF. NOTE: MUST BE WIRED TO CONFORM TO LOCAL WIRING CODE. THIS SWITCH CANNOT BE USED WITH L.V.C. FIGURE 3 WIRING ENCLOSURE COVER UP RED LIMIT SWITCH ADJUSTMENT AND DOWN WHITE LIMIT SWITCH ADJUSTMENT TO JUNCTION BOX, MOUNTED IN SCREEN CASE, IN WHICH INTERNAL WIRING TERMINATES IN BLUE, BROWN AND BLACK LEADS COSMOPOLITAN® ELECTROL® INSTALLATION Surface travel is stopped automatically in the fully opened and closed positions by limit switches that are properly adjusted at DA-LITE. Should it be necessary to adjust for more or less picture drop (viewing area), proceed in the following manner: NOTE: Use a screwdriver or allen wrench to make adjustments. SETTING THE DOWN LIMIT POSITION TO REDUCE SCREEN DROP: Turn the white limit switch screw clockwise to decrease the amount of screen drop. Run the screen down to test the stop position. If the screen drops too far, raise the screen about one foot and adjust the limit switch again. Repeat until the desired position is set. TO INCREASE SCREEN DROP: Turn the white limit switch screw counterclockwise to increase the amount of screen drop. Run the screen down to test the stop position. If the screen does not drop enough, raise the screen about one foot and adjust the limit switch again. Repeat until the desired position is set. Do not adjust for more drop than what was ordered. At least 1-1/2 wraps of fabric must remain on the roller. SETTING THE UP LIMIT POSITION CAUTION: Do not allow the slat bar to wrap over the top of the roller when the screen is rolling into the case. The screen could be damaged. SCREEN TRAVELS INTO CASE TOO FAR: Turn the red limit switch screw clockwise to decrease the amount of travel. Run the screen up to test the stop position. If the screen does not stop properly, lower the screen about one foot and turn the limit switch again. Repeat until the desired position is set. SCREEN DOES NOT TRAVEL FAR ENOUGH INTO CASE: Turn the red limit switch screw counterclockwise to increase the amount of up travel. Run the screen up to test the stop position. If more travel is desired, lower the screen about one foot and adjust the limit switch again. Repeat until the desired position is set. ▲! SCREEN ADJUSTMENT FOR 220/240V SCREENS WITHOUT A BUILT-IN LOW VOLTAGE CONTROL