ICPDAS tM-7530 Quick Start Manual

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 1 tM-7530 Tiny RS-232/CAN converter Quick Start Guide Product Website: https://www.icpdas-usa.com/tm_7530 1. Introduction ICP DAS has provided a lot of UART/CAN product solutions which are widely recommended in the market. These UART/CAN converters can help users to implement the communication between RS-232 and CAN network. In order to cater for costing requirement, we provide a new solution of RS-232/CAN converter, tM-7530. The tM-7530 is a tiny RS-232/CAN to fit narrower environment as a result of its small size. It has isolation on power side and on CAN bus side and its performance is faster than other RS-232/CAN module. The function of tM-7530 can full compatibly with I-7530 and I-7530T. Besides, it provides new function such as listen only. User can use this function to listen CAN bus messages and error detection. According to above features, tM-7530 is an economical and practical RS-232/CAN converter solution.

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 2 1 ----------------------------------------------------------------------------------- Hardware Introduction and Installation The left graph is the surface of tM-7530. It uses D-sub 9 pin female connector as RS-232 communication interface and uses 2 or 3 wire to connect CAN bus with spring type connector. It has 2 LED indicators Run and Err. They are used to response module status immediately at all time. Table: RS-232 Pin Assignment Table: Power and CAN Bus Pin Assignment Pin 3-wire Pin Power RS-232 1 +Vs 1 N/A (10~30VDC Power) 2 GND 2 RS-232 TxD 3 F.G. 3 RS-232 RxD 4 N/A Pin CAN 5 RS-232 GND 1 CAN_L 2 CAN_H 6 N/A 3 CAN_GND 7 N/A 8 N/A 9 N/A tM‐ 7530 Quick Start

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 3 Table: LED Indicator LED Indicator Condition Status Configuration Mode Flash Once Per Secord Turn on when no data needs to be Run Run Mode sent Flash once when sending a CAN message FIFO overflow Err CAN Bus Off Always turned on CAN Error Passive Some errors occurred Flash How to connect with spring type connector? Press and Insert.

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 4 8

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 5

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 6

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 7

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 8

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 9 The test interface is divided to two areas. One is for sending CAN messages, and the other is for reception. If users want to send CAN message, fill the data into the corresponding field, and click “Send” button. If the CAN converter gets any CAN messages, they will be shown in received area automatically. About the details for the VxCAN Utility operation please refer to the users’ manual of the VxCAN Utility in the following web site. http://ftp.icpdas.com/pub/cd/fieldbus_cd/can/virtual_can/vxcan_utility/