Duratech Link Touch Manual 

Technical specifications Box contents About the Link Touch Installation instructions Control functions: pool lights Control functions: heat pump & pool cover Advanced control functions: pool lights Display: Status icons Safety information First use How to use the Settings Menu Connecting to ... Cover operation settings Beep settings Temperature units display setting Aux setting Factory reset Caring for the Link Touch Troubleshooting Resetting the Link Touch Environment / disposal of old equipment Service & warranty Regulatory compliance Page 3 Page 4 Page 4 Page 5 Page 6 Page 7 Page 8 Page 9 Page 10-11 Page 11 Page 12 Page 13 Page 14 Page 15 Page 16 Page 17 Page 18 Page 19 Page 19 Page 20 Page 22 Page 22 Page 22

Interface: LoRa 868 MHz USB-C Ambient Air Temperature: 0°C to +40°C Humidity 10% to 90% RH - non condensing Ingress protection rate: IP20 IEC Protection Class: Class II Size (in mm): 89,5 (Height) 186,5 (Width) 17,5 (Depth) Weight: 298 g

The Link Touch is the remote of your pool control system. By using the Link Touch, you can control the lights, the heat pump and cover of your swim- ming pool. The Link Touch includes an integrated Li-Ion battery which can be charged automatically when mounted onto the wall mount. The Link Touch connects wirelessly with a compatible Link Driver PLP-REM and with DURA-V, DURA-Vi and DURAPRO heat pumps. Please check our website for latest information regarding compatibility with heat pumps The Link Touch can operate in different modes: - - - - When the Link Touch is inserted in the wall mount, it will charge till full battery. When Link Touch is removed from the Wall mount, it will work instantly when touched. When the Link Touch is removed from the Wall Mount and it is not touched for 15 seconds, it will turn into “Standby mode”. In this case the display will be off. As soon as the touch panel is touched by the user, the display will turn on again. When the battery is empty, the Link Touch will no longer function. To turn on the Link Touch again, it needs to be inserted into the powered wall mount. In this case the display will be active again and the Link Touch will start communicating with the external devices.

power cord 1. Plug the USB power cord into the power adapter 2. Plug the other end of the USB power cord into the USB connector of the wall mount. 3. Plug the power adapter in a power outlet. 4. Mount the Link Touch onto the wall mount.

Colour wheel: Slide to change colour of Pool Lights (only DLT10-RGB) Colour program: Press for previous colour program. Colour program: Press for next colour program. Colour temp.: Slide to the right to adjust the pool light from “warmwhite” to “cool white” Dimming level: Slide to the right to increase the brightness of the Pool Lights Control functions: pool lights all-guides com

Press to increase desired temperature Pool cover OPEN: Press and hold to open the pool cover. When finger is removed from button the cover will stop immediately Pool cover CLOSE: Press and hold to close the pool cover. When finger is removed from the button, the cover will stop immediately ON/OFF heat pump: Press to switch pool heat pump ON/OFF Pool water Temp. DOWN: Press to decrease desired temperature NOTE: Depending on AUX MODE, in settings COVER OPEN/CLOSE or FUNC A/B Control functions: heat pump & pool cover

current settings Activate the settings menu (*), then use left arrow key to select the desired setting. Activate the settings menu (*), then use right arrow key to select the desired setting (*) Touch the display for 3 seconds to go in to the settings menu. Advanced control functions: pool lights

Pool cover: Battery capacity Link Touch is communicating werelessly Pool heat pump is on Pool lights are connected Relays A and B are connected Pool cover is opening/closing Pool Heat pump is on and heating Pool lights are on There is an error with relays A and B There is an error with the pool cover Pool heat pump has an error There is an error with the pool lights Battery is charging No battery detected Display: Status icons

accessories. The Link Touch should be used only for this purpose, as described in this user guide. Precautions for Setup - - - - - - - - - Precautions for Operation - - - - - The Link Touch can only be mounted indoor. Do not mount outdoors. The power adapter is designed for 100 - 240V, 50/60 Hz. Verify if the power outlet voltage is within this range before plugging in your power adapter Install the device close to an accessible power outlet. Make sure the power/USB cable can be easily disconnected from the power outlet at all times Protect the power/USB cable and the power adapter from being strained pinched or bucked Place the Power/USB cable out of walkways to prevent tripping over the cable. Use only the power adapter provided with the Link Touch. Use of an incorrect power adapter may cause overheating or fire. Do not bend or place a heavy object on the power/USB cable as it could damage the cable and result in risk of electric shock or fire Do not use the power/USB cable if damage or frayed Be sure to hold only the connector end of the power/USB cable when disconnecting. Repeated pulling on the cable will damage the cable. Protect the Link Touch from moisture and do not operate if power/USB cable or plug are defective. Never touch a power plug with wet hands. Do not place anything on top of the Link Touch Never spill liquid of any kind on the Link Touch Do not drop or hit the Link Touch

the Link Touch Fully charge the Link Touch before using the device The Link Touch is NOT water proof The Link Touch is NOT dust proof Precautions for Cleaning, Transport and Storage - - Use a soft, damp cloth to clean the exterior of the Link Touch Do not use cleaning tissues or chemical substances which might damage the surface. This Link Touch contains no user serviceable parts. Do not attempt to service the Link touch yourself. Repair service should be performed by a authorised technician. all-guides com

3 SEC Tap Tap Tap Touch the display on the Link Touch for 3 seconds to go into the settings menu. Use arrow keys to select the desired setting. Touch the display once to confirm the setting.

settings menu. Touch the screen once to put the Link Touch in pairing mode. Connecting to ... This “Pairing”-mode will allow the Link Touch to establish a wireless con- nection with other devices such as : - PLP-REM, PLP-REM-300, PLP-REM-450, linking per functionality (lights, cover) - The heat pump Note : In case the PLP-REM-450 is already linked with cover and lights and heat pump , it will distribute the links to the Link Touch automatically. Option 1: Make sure the Link Touch is in close proximity (<2m) with the device which you would like to pair with wirelessly. Select “Pair Start” on the Link Touch. Power on the device. The device will be in pairing mode for about 2 minutes after switched on. The Link Touch will now be pairing with the device. Option 2: (only in combination with PLP-REM-450) Connect the Link Touch with the PLP-REM-450 using the USB cable. Select “Pair start” on the Link Touch. The Link Touch will now be pairing with the PLP-REM-450 and all linked devices (lights, cover and heat pump ) to it.

Go to “AUX SETTING” in the settings menu. Touch the screen and select “COVER” Go to “DEADMANSWITCH” in the settings. Touch the screen to select “DEADMANSWITCH ENABLED” There are 2 modes: Deadman switch operation enabled: The cover operation will run when pressing and holding the finger on the button and will stop when releasing the finger from the button Deadman switch operation disabled: The cover operation will run with a single touch of the button and will stop when touching the button again. Warning : Always make sure that when operating the cover with the remote device, that the pool is always in sight of the operator, to make sure the path for the cover is clear and nobody gets injured. Note that Propulsions Systems cannot be held responsible for any damage or injury during the operation of the cover.

Touch the screen to select the re- quired operation mode. (note that default setting is set to “BUZZER ENABLED”. The buzzer sound can be set to ON or OFF. If set to ON, then the buzzer will sound each time as confirmation for touching any of the active areas of the Link Touch. The beep will also sound when the Propulsion System’s cover is in operation. In case of a third party cover, the beeping sound will not be active Warning : It is advised to set the buzzer setting to “ON”, in order to have an audio feedback during the operation of the cover.

Go to “TEMPERATURE °C/°F” in the settings menu. Touch the screen to select the re- quired units. (note that default setting is set to “°C”. The temperature units on the display can be set to Celsius or Fahrenheit all-guides com

Go to “AUX SETTING” in the settings menu. Touch the screen to select “AUX SET- TING AUXILIARY”. Go to “AUX MODE A” in the settings menu. Touch the screen to select the re- quired mode “TOGGLE or “PULSE”. This setting will allow the installer to change the cover function to an ON/OFF function for a different device. The “AuxSetting” can be set to enable or disable. If disabled, then the Link Touch is considered to control a cover system. If “AuxSetting” is enabled, then the Link Touch will control a different device with the cover buttons and the buttons will act as an “ON” and “OFF” button.

tings menu. Touch the screen to reset the Link Touch to factory settings You can reset the Link Touch to the factory default settings. Resetting the Link Touch reverts all settings to the factory default set- tings. Any settings, including wireless connections, that have been changed are lost. The factory reset can be found in the setting menu.

Troubleshooting The Link Touch requires very little maintenance - - This section includes information about what to do if you encounter a problem with your Link Touch. If you need further assistance, please contact your installer or distributor or go to the support section of the Propulsion Systems website at www.duratech.be/duracare You may occasionally need to clean the exterior of the housing. To clean the exterior of the Link Touch, wipe the exterior with a soft, damp cloth. NOTE: Do not use cleaning tissues or chemical substances which might damage the surface Don’t place the Link Touch in direct sunlight Battery too hot Heat pump error Pool light error Aux error Cover error remove from heat source or take out of sunlight consult manual of heat pump for trouble shooting consult manual of Pool light for trouble shooting consult manual of auxiliary connected device for trouble shooting consult manual of cover for trouble shooting

You can reset (=reboot) the Link Touch without loosing the preffered set- tings. To reset the Link touch: Press the “Reset” button on the back of the Link Touch, using a paperclip. RESET

Service & warranty Regulatory compliance This symbol of a crossed out waste bin on a product, its packaging and/or accompanying docu- ments means that the product is subject to the European Directive 2002/96/EC as well as national law for implementation of the directive. Directive and law prescribe that electrical and electronic products must not be disposed of with household waste. The customer must dispose of the product by delivering it to a designated station for collection, treatment and recycling of waste electrical and electronic equipment. The correct disposal of your old appliance is free of charge and will help prevent potential negative consequences of the environment and human health. For more information about disposing your old appliance, contact your city office, waste disposal service, or the shop where you purchased the product. If you need service or information or if you have a problem, please contact your local dealer. If needed they will contact the manufacturer to solve your problem. They are gladly willing to assist you! You can find more information at www.linktouch.eu We warrant all parts to be free from manufacturing defects in materials and workmanship for a period of two years from the date of retail purchase. This warranty is limited to the first retail purchaser and is not transferable. The liability of the manufacturer shall not exceed the repair or replacement of defective parts and does not include any costs for labour to remove and reinstall the defective part, transportation to or from the factory, and any other materials required to make the repair. This warranty does not cover failures or malfunctions resulting from the following: 1. Failure to properly install, operate or maintain the Link Touch in accordance with the installation guidelines provided in this manual. 2. The workmanship of any installer of the product. 3. Abuse, alteration, accident, fire, flood, lighting, rodents, insects, negligence or acts of god. 4. Use of non-factory authorized parts or accessories in conjunction with the product. LIMITATION OF LIABILITY This is the only warranty given by the manufacturer, No one is authorized to make any other warranties on our behalf.This warranty is in lieu of all other warranties, expressed or imlied, including but not limited to any implied warranty of fitness for a particular purpose and merchantability. We expressly disclaim and exclude any liability for consequential, incidental, indirect or punitive damages for breach of any expressed or implied warranty. This warranty gives you specific legal rights, which may vary, by country. WARRANTY CLAIMS For prompt warranty consideration, contact your dealer and provide the following information: proof of purchase, model number, serial number and date of installation. The dealer will contact the manufacturer for instructions regarding the claim and determine the location of the nearest service point. This product uses radio equipment wich fuly complies with the european harmonized standards of RED (Radio Equipment Derections) 20/4/53/EC. see below for the compleet EU declaration of comformity

Dooren 72 1785 Merchtem, Belgium Tel +32 2 461 02 53 Fax +32 2 706 59 60 www.duratech.be [email protected] We reserve the rights to change all or part of the contents of this document without prior notice 402-0235-191008