Furzone THOR A5 Manual Instruction

1 Technical data 1.1 Specifications ● Dimension : 206x52x53mm (LxWxH) ● Weight : A5 - 470g / 1.04lb A5 Plus - 530g / 1.17lb ● BRUSHLESS DC motor ● Motor power : 40W / 36W ● Motor life : 30,000 hours ● Total recharging time : A5-1.5 hours A5 Plus - 2.5 hours ● Run time : A5 - 2 hours A5 Plus - 5 hours ● Strokes per minute : 3500 spm ● LED indicator : smart charging led indicator 100%. 75%. 40%. 10% ● Torque : 10 kgf-m ● Power adapter : 1.2M cord (12V/3A power adapter) ● Battery : Lithium-ion ● Battery pack (circuit protection) ● Cord pack (12V/2A) : 1.2M cord ● Charging stand : charging LED indicator ● Charging stand dimension (LxWxH) : 95x90x51 mm ● 12V/2A cable (for 40800 power bank) : 20cm cord (support 12V/2A DC out) ● 1-Year limited motor warranty

indicator 100%. 75%. 40%. 10% 4. Switch lever 5. Clipper head 6. Interlock clipper head 7. Interlock battery Fig. 1 Fig. 2 4 2 2 Assembly and function 2.1 Component as Figure 1. Clipper machine 2. Blade A5 - A1A12 #10-1.5mm A5 PLUS - A5A12 #30W-0.5mm 3. Battery pack (1.2M cord) Run Time 5 hours 4. Charge stand 5. Cord pack (optional) 6. Power adapter (1.2M cord) 13.5V/2A 7. 40800 Power bank (optional) 8. 12V/2A Cable (for 40800 Power bank)(optional) 9. 100ml Blade oil 10. Cleaning brush 2.2 Overview 1 2 3 5 6 8 10 9

and horses. Two comb-shaped blades are the cutting tool. The bottom blade facing the skin (3) is standing firm and is fixed on the blade hinge (4). The top is agitated crossways that one. The top blade is moving by the help of a turning lever (1). Fig. 3 Fig. 4 Switch in OFF-position (“0”) Fig. 5 Switch in ON-position (“I”) Fig. 6 Interlock clipper head Fig. 7 Interlock battery 1. Charging station 2. Power adapter 3. Apart charging cavity for the battery 4. Charging cavity for the clipper with integrated battery 3 2.3 Abstract 2.4 Operating elements 2.5 Charging station

2. Contacts 1. Place the charging station on a firm, even, dry, clean and free underground. 2. Plug the charging station in the power outlet. Fig. 9 Fig. 10 4 2.6 Battery 3 Operation 3.1 Initial startup 3.1.1 Setting up the charging station ● Observe all technical data according to the operating conditions (3 Technical Data). ● The installation surface must be even and must dispose of sufficient stability and payload. ● The location of installation must be protected against humidity and rain. ● Power outlets in the outer area must be equipped with a residual current circuit breaker (FI). ● The workplace must dispose of sufficient illumination and ventilation. ● The location of installation must be out of reach of children. 3. The charging station has electronics that constantly check its functions. A switchover may therefore last up to 3 seconds. 4. Correctly to the power outlet and the charging station is ready for use. 5. If the battery is very depleted, the charging station wakes the battery. This may require up to 5 minutes. After that the normal charging process will start.

(1) and the battery (2) for foreign particles and contamination. 2. Assure, that the switch lever of the clipper is in OFF-position (“0”) (fig. 4). 3. Insert the battery (2) in the clipper (3), until the battery interlock (1) is engaged on both sides. 4. Put the clipper with the inserted battery (1) or spare battery (2) from above without force into the provided charging cavity of the charging station. 5. Waiting for the battery charging time (1 specifications). 6. Battery is charging. During the charging time the control light is illuminating red (3). As soon as the battery has been charged to a min. 90%, the indicator lamp will change to blue and the charging station switch to “trickle charging”. 7. Hold the charger firmly with one hand and pull the clipper (1) or the battery (2) out with the other. 5 3.1.2 Charge battery

closed, lift the latter up using a screwdriver (1) while simultaneously pressing the blade lock. 2. Fit the clipper head (1) on the open blade hinge (2). 3. Fold the clipper head (2) by light pressure on to the clipper (1) which is switched on. 4. Make sure, that the clipper head (1) is engaged firmly. Fig. 14 Fig. 15 Fig. 16 Fig. 17 6 3.1.3 Fitting the clipper head NOTE! For proper operation make sure that the clipper head (1) is engaged correctly.

“0” (fig. 4). 2. Push the battery interlock (2) on both sides inward and pull the battery (1) out of the clipper. 3. Insert charged battery (1) into the shearer (2), until the battery lock is locked in on both sides. 1. Move the switch to position “0” (fig. 4). 2. Push the interlock clipper head. Fig. 20 7 3.2 Activities during operation 3.2.1 Clipping 1. Fix and calm the animal sufficiently before clipping. 2. Switch on the clipper already in the field of vision of the animal. 3. Approach to the animal from ahead. 4. During clipping, look at the behaviour of the animal. 3.2.2 Changing the battery When the battery is unloaded, the clipper is turned off by a protective circuit. 3.2.3 Changing the clipper head

clipper head is pressed. 4. Take off the clipper head. 5. Clean the opened hinge by the help of the provided brush. Fig. 21 The blades must be oiled before, during and after every use. When the blades of the clipper are leaving stripes or are running with reduced speed, this is a signal that oil is required. Place a few drops of oil ahead and laterally on the clipper blades (see arrows in Fig. 22). Wipe off the excessive oil with a smooth, dry cloth. Lubrication sprays do not have sufficient oil for a good lubrication, but serve for cooling the blades. Immediately change damaged or crenated blades to avoid injuries. Fig. 22 8 6. Fit the favoured clipper head to the blade hinge and fold it on to the switched-on clipper by light pressure. (Fig. 15, 16, 17). 3.2.4 Lubrication To receive good clipping results and to increase the durability of the clipper and the clipper head, it is necessary to apply a thin oil coat between top and bottom blade (Fig. 22). CAUTION! Insufficient lubrication of the clipper head causes heating and a reduced durability of clipper and blades, as well as a reduction of the battery runtime. Therefore: ● Lubricate the blades sufficiently during the clipping (at least every 15 minutes), so that they do not drain (Fig. 22). ● Only use the lubricants prescribed by the manufacturer.

power supply. 2. If necessary, take away hairs from charging cavities. 3. If required, clean the contacts (1) with a dry cloth. 4. Clean the contacts of the battery and the shearer with a dry cloth as necessary. 5. (2) LED indicator Red light display charging Blue light display fully charged Fig. 23 Fig. 24-1 Fig. 24-2 9 CAUTION! Remove all the leaking, used up or excessive grease from all the lubrication points, and it is to be disposed in accordance with the local regulations. 3.2.5 Cleaning To receive good clipping results and to increase the durability of the clipper and the clipper head, it is necessary to apply a thin oil coat between top and bottom blade (3.2.4 Lubrication). Clipper head and hinge Clean clipper heads und hinge between the different clippings. Charging station 3.3.1 Cord use (1) Cord pack (2) Power adapter

(1) Vac board (2) Screwdriver (3) Vac attachment

● Power indicator : 4 LED lights display battery life ● Output : 12V/2A & 15V/3A, 2 USB 5V/1A & 5V/2A ● Input : 12V/3A ● Capacity : 24000mAh Lithium-ion ● Operating time : 12V/2A : 8.5 ~ 9 hours (for 920.610 Clipper), 15V/3A : 4.5 ~ 5 hours (for 614.611 Clipper) ● Charging time : 4.5 ~ 5 hours ● Weight : 560gm / 1.23lb ● Dimension : 150x75x60mm ● The optional cigarette lighter plug charger lets you charge 40800 power bank on the way to and from the course using any 12V auto outlet ● With dual USB 5V/1A 5V/2A output charger suitable for all 5V devices, cell phone, tablet, and 3C products Fig. 39 Fig. 40 Fig. 41 Fig. 42 11 3.3.3 Support 40800 power bank (optional) (1) Cord pack (2) 12V/2A Cable (3) 40800 power bank (4) 920 Clipper

4.1 Swinging head (1) Vac board (2) Screwdriver (3) Upper board (4) Screw (5) Small spring (6) Small bearing (7) Swinging head

● Some tasks only may be done by especially trained personal or by an authorised service centre. These tasks are marked with (S). Malfunction Cause Rectification Top blade does not move Clipper head is not well engaged Engage the clipper head correctly when the motor is running Turning lever is defective Replace turning lever (S) Motor is not running Battery is dead Charge battery Contacts dirty Switch clipper off and clean the contacts Faulty battery Replace battery Smell of burning from the motor housing. Motor burned out Have motor and / or electronics replaced (S)

or not at all Clipper blade is blunt Have top and bottom blades re- sharpened by service centre (S) Clipper blades have not been correctly ground Clipper blades are not oiled Oil clipper blades every 15 minutes The animal‘s hair is wet Only clip dry hair Hairs jammed between top and bottom blades Take off clipper head, push the top blade half away from the clip- per head, take away hairs between top and bottom blade Clipper head has too little clipping pressure Have clipper head inspected (S) Motor does not work Faulty motor and / or electronics Have motor and / or electronics replaced (S) Clipper head blocked Clean and oil clipper head Motor runs very slowly Clipper blades were not oiled sufficiently Oil clipper blades Running time of a fully charged battery is too short and / or blades are getting hot Clipper blades were not oiled sufficiently Oil clipper blades Dead, not fully charged or defective battery has been used Only use intact and completely charged original battery The control light of the charging station in not on Charging station is not connected to the power supply Connect the charging station to the power supply Charging station is faulty Have charging station inspected (S) When the battery is fully charged, the light does not change from red to blue Contacts of battery and / or charging station are dirty Clean contacts Faulty battery Replace battery Contacts of the charging station are deformed Have the charging station re- paired (S) CARE AND MAINTENANCE The cleaning and maintenance procedure must be carried out after every use.  All maintenance or blade change operations must be carried out with the appliance switched OFF and removed from the mains adapter.  Never immerse the appliance in water.  After every use, remove the guide comb then use the small brush to eliminate any hair from the cutting head and its seat.  Clean the outside of the appliance with a soft cloth. Never use solvents or abrasive detergents.  Remove the cutting blade (fig. 20, 21). and evenly oil the blades and the seat of the motor pin which is located on the inside.

the appliance appears to be diminished, the cutting blade must be replaced.  Once the appliance has been cleaned, the guide comb can be fitted back in place since it also helps to protect the blade.  Use this appliance only for its intended purpose. WARNINGS: 1. Keep the appliance dry. DO NOT place or use this appliance near bathtub, bathing sink, showers or other liquid area. 2. DO NOT allow children to play with the appliance, never leave children or handicapped individuals unattended with access to professional equipment. 3. NEVER reach for any electrical appliance that may have fallen into water or any other liquid to avoid electric shock. 4. NEVER use in bathing area or while washing wet animals to avoid electric shock. 5. If the appliance is damaged, do not disassemble or repair this unit yourself. It must be replaced by the manufacturer or its service agent in order to avoid a hazard. 6. NEVER use any appliance or component of an appliance in any manner except for that which it was designed. Do not make alternations to any appliance or component which may lead to personal or environmental harm .NEVER use a defective unit or component. 7. The elements used to pack the unit (plastic bags, cardboard box, etc.) must be kept out of reach of children as they are a potential danger to them. 8. The manufacturer accepts no responsibility for damage caused by improper or erroneous use. 9. Do not leave the appliance on charge in wet places and do not recharge the appliance when it is wet. 10. The appliance comes equipped with a Lithium battery. have the battery removed by qualified technical personnel or by the treatment and recycling center . 11. Keep the battery away from magnetic fields, sources of heat and naked flames. 12. Do not use a comb or a set of blades if they are damaged. Replaced them immediately as they may cause injury. 13. Take care not to scratch the skin when handling the appliance with the set of blades without combs. FURZONE CUT ON LINE

1. The guarantee conditions for this appliance are as defined by our dealer in the country of sale. The guarantee period is 12 months starts from the date of purchase as stated on the Present guarantee card regularly filled out and stamped by the dealer or on the sale’s invoice. 2. The guarantee is applicable only against submission of the present guarantee card or the sale’s invoice. 3. The guarantee covers the elimination of all defects arisen during the guarantee period resulting from proven faults in material or workmanship. The elimination of the defects will be made either by repairing the appliance or exchanging it. The guarantee does not cover any damage arising from incorrect connection to the power supply, improper use, breakage, normal wear and non-compliance with the instructions for Use. 4. The guarantee service is carried out free of charge; it does not affect the expiry date of the guarantee. 5. The guarantee becomes void if repairs are undertaken by unauthorized persons. In case of defect, please return the appliance well packed and together with the guarantee card regularly dated and stamped to one of our FURZONE Service Centers or to the dealer who will send it to the official importer for the guarantee service. FURZONE WARRANTY REGISTRATION Important: Completely fill out and mail within 10 days purchase. NAME : ________________________________________________________________ ADDRESS : _____________________________________________________________ CITY STATE, ZIP CODE ___________________________________________________ PHONE ( ____ ) __________________ DATE PURCHASED______________________ MODEL : _______________________________________________________________ PURCHASED FROM : _____________________________________________________ I HAVE READ AND CLEARLY UNDERSTAND THE WARRANTY TERMS. _______________________ _______________________ SIGNATURE DATE D CUT ON LINE