Aquafog XE 2000-HS User's Manual And Operating Instructions

6. Fan Motor Becomes Excessively Hot The main fan motor normally becomes very hot to the touch. However, if it gets so hot that it begins to smell or smoke or the power cord becomes hot, discontinue operation and consult an electrician to properly evaluate the problem. 7. Electrical Breaker Tripping If the electrical breaker trips off, there is an overload in the system and there may be a serious motor problem. Turn off all other devices connected to the same circuit. If the breaker continues to trip, the motor is probably in need of ...

Aquafog and accessories are warranted to the original purchaser against defects in material and workmanship under normal use for one full year from date of purchase. Any part determined to be defective and returned to the manufacturer, shipping cost prepaid, will be repaired or replaced at Jaybird Manufacturing, Inc.'s discretion without charge. Proof of purchase date and an explanation of the problem or complaint must accompany the returned portion of the machine. Jaybird Manufacturing, Inc. reserves the right to verify the legitimacy of claimed defects. The provisio ...

fast moving and hot parts will cause injury and/or burns. 10. If the equipment starts to vibrate abnormally, STOP the motor and check immediately for the cause. Vibration is generally an indication of trouble. Fogging Precautions DANGER A motionless atomizer may appear safe, but its blade could suddenly begin high- speed rotation without warning as a result of control programming. When a XE 2000-HS is automated by controls, warning signs should be posted near the high- speed equipment. Disconnect and lock out power source to inspect or service the u ...

Common Setups . . . . . . . . . . . . . . . . . . . . . Placement . . . . . . . . . . . . . . . . . . . . . . . . Unpacking / Installation . . . . . . . . . . . . . . . Pivot / Utilities . . . . . . . . . . . . . . . . . . . . . . . Power Connection . . . . . . . . . . . . . . . . . . . . . Operation . . . . . . . . . . . . . . . . . . . . . . . . . . Troubleshooting . . . . . . . . . . . . . . . . . XE 2000-HS Exploded View . . . . . . . . . . Part Identification List . . . . . . . . . . . . . . . . Oscill ...

Wiring the Oscillator EXTENSION CORD SPECIFICATIONS* FOR SINGLE FAN USE ONLY • (AWG - American Wire Gauge) Voltage 25 to 50 ft. 50 to 100 ft. 115 16 AWG 14 AWG power connection GROUND FAULT RECEPTACLE IS RECOMMENDED AND MAY BE REQUIRED BY LOCAL AND/OR NATIONAL CODE. PROPERLY GROUND ALL CONNECTIONS Remove the black plug from the the top of the motor's junction box. Install the oscillator power cord and connector. This cord is pre-measured to the appropriate length. DO NOT SHORTEN. Remove the motor junction box cover. Stri ...

can be made to direct the fogging output to a desired location. This unit has a positive pivot locking system with four available positions. ~ 5º up ~ Horizional ~ 7º down ~ 14º down To Make an Adjustment Relieve the weight of the unit and lift one pivot lock up and rest it in the middle of the "M". While securely supporting the unit, lift the second lock up. Adjust unit to desired angle. Re-engage both locks into the closest available slot. NOTE: Use both sides of the "M" to access all four pivot angles. Pivot Lock ...

A.) Check voltage requirements on unit and electrical supply. Check for live receptacle, plug, power line and unit's power On/Off switch. B.) Look for any loose connections inside the main motor's junction box. 2. Unusual Noise A.) Squealing at start-up or during operation may be caused by the motor shaft's bearing seal. Spray with lubricant at the front of the motor where the shaft exits the motor's frame. 3. No Fog A.) If the Flow Control Valve is closed, turn the knob in-line with the valve to open fogging output. Visually check Feed Line conections leading to the ...

► Side view of motor ◄ Rear of Housing 20 57 58 Hanger Bolt 395 116 518 576 575 7 523 522 35 400 406 407 574 573 400-047 ◄ From Sump Pump 288 To Switch Box ▼ 545 400-114 546 400-089 568 571 510 308 20 395 657 32 126 125 154 58 32 603 602 659, 32 658, 42, 660 Hanger Options U-Bolts 607 538 16 481 45 517 57 116 10-2000 56 Oscillator's power supply port 607 10-2000 ...