Comelit 4893M Technical Manual

Warning............................................................................................. 2 Description........................................................................................ 3 Technical features............................................................................ 4 Installation......................................................................................... 5 Changing nameplates...............................................................................6 Settings............................................................................................. 7 Programming.................................................................................... 8 Call address programming for 2/4 users and additional external unit.8 Operation with additional external units.................................................9 Operation with switching device 1404 (default).....................................9 Operation with switching device 1405....................................................9 Programming a generic call address....................................................10 Disabling the COM-RTE contact...........................................................11 Connections.................................................................................... 12 Door open indication use variant..........................................................12 Variant for using a safety door lock and additional power supply.....12 Using the RC network for door lock filter on relay contacts..............12 System performance and layouts................................................. 12 Warning Intended use This Comelit product was designed for use in the creation of audio and video communication systems in residential, commercial or industrial settings and in public buildings or buildings used by the public. Installation All activities connected to the installation of Comelit products must be carried out by qualified technical personnel, with careful observation of the indications provided in the Manuals / Instruction sheets supplied with those products. Wires Cut off the power supply before carrying out any maintenance procedures. Use wires with a cross-section suited to the distances involved, observing the instructions provided in the system manual. We advise against running the system wires through the same duct as the power cables (230V or higher). Safe usage To ensure Comelit products are used safely: • carefully observe the indications provided in the Manuals / Instruction sheets • make sure the system created using Comelit products has not been tampered with / damaged. Maintenance Comelit products do not require maintenance aside from routine cleaning, which should be carried out in accordance with the indications provided in the Manuals / Instruction sheets. Any repair work must be carried out • for the products themselves, exclusively by Comelit Group S.p.A., • for systems, by qualified technical personnel. Disclaimer Comelit Group S.p.A. does not assume any responsibility for • any usage other than the intended use • non-observance of the indications and warnings contained in this Manual / Instruction sheet. Comelit Group S.p.A. nonetheless reserves the right to change the information provided in this Manual / Instruction sheet at any time and without prior notice.

  2. Camera lighting LED set by default to activate in response to a call (can be disabled by setting DIP 7 to ON, see Settings)   3. Wide-angle colour camera   4. Loudspeaker   5. Indicator LED call sent / lock-release activated audio active / system busy   6. Call button 1 / 2 / 4 users   7. Microphone   8. Terminal block M1 LL bus line connection RTE request to exit button input COM common input for RTE and DO contacts DO door open indication input   9. PR programming input/output switch 10. CNF programming confirmation switch 11. Loudspeaker volume control 12. Audio balance 13. Terminal block M2 SE- SE+ connection for electric door lock NC relay normally closed contact NO relay normally open contact C relay common contact 14. JP1 enabling the RC network for door lock filter on relay contacts 15. DIP-SWITCH for function programming 16. Microphone volume control Wall-mounted external unit for Quadra series door entry monitor. Die-cast aluminium front panel, wide-angle colour video camera and single LED for lighting at night. Mechanical buttons with the option of setting 1 to 4 call buttons via DIP-switch. Indicator LED for call sent, lock-release activated, audio activated and system busy. Loudspeaker volume adjustment and audio balancing. Bus line power supply.

Type of finish Die-cast aluminium Audio/video system Yes Wall-mounted Yes Camera Colors Lens size (mm) 2,1 Diagonal viewing angle (°) 100 Minimum colour illumination (lux) 1 Power supply Bus Maximum current absorption (mA) 250 Clamps LL RTE COM DO SE- SE+C NC NO Buttons to call Yes Total buttons 4 Microphone volume control Yes Loudspeaker volume control Yes Operating temperature (°C) -25 ÷ +55 IP protection rating IP54 Vandal Resistant rating (IK code) IK08 HARDWARE SPECIFICATIONS Visual signalling Yes Acoustic signalling Yes GENERAL DATA Product height (mm) 195 Product width (mm) 95 Product depth (mm) 28 COMPATIBILITY Kit audio/video system Yes ELECTRICAL SPECIFICATIONS Door release (dry contact bridge) Yes

the light. In dim environments, we recommend additional lighting is provided. 4 2 3 1 163 cm 130 cm COM L L RTE 4 5 1 3 JOHN DOE 2 1 2 1 2 3 4 1 Settings Microphone Loudspeaker 6 1 2 1 2 1 2 3 You can download the free software (art. 1235A) to print the entrance panel name cards, using the adhesive pre-cut sheets available in our catalogue (art. 1217A). OPEN