Biostar GF8200 M2G PLUS - BIOS Setup Manual

FCC Information and Copyright This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. The vendor makes no representations or warranties with respect to the contents here and specially disclaims any implied warranties of merchantability or fitness for any purpose. Further the vendor reserves the right to revise this publication and to make changes to the contents here without obligation to notify any party beforehand. Duplication of this publication, in part or in whole, is not allowed without first obtaining the vendor’s approval in writing. The content of this user’s manual is subject to be changed without notice and we will not be responsible for any mistakes found in this user’s manual. All the brand and product names are trademarks of their respective companies.

Chapter 1: Introduction ............................................................ 1 1.1 Before You Start ................................................................................ 1 1.2 Package Checklist............................................................................. 1 1.3 Motherboard Features...................................................................... 2 1.4 Rear Panel Connectors ..................................................................... 3 1.5 Motherboard Layout......................................................................... 4 Chapter 2: Hardware Installation ............................................. 5 2.1 Installing Central Processing Unit (CPU)....................................... 5 2.2 FAN Headers...................................................................................... 7 2.3 Installing System Memory................................................................ 8 2.4 Connectors and Slots....................................................................... 10 Chapter 3: Headers & Jumpers Setup..................................... 12 3.1 How to Setup Jumpers .................................................................... 13 3.2 Detail Settings.................................................................................. 13 Chapter 4: RAID Functions ..................................................... 18 4.1 Operating System............................................................................ 18 4.2 Raid Arrays ...................................................................................... 18 4.3 How RAID Works............................................................................. 18 Chapter 5: Useful Help ............................................................ 22 5.1 Driver Installation Note.................................................................. 22 5.2 Software............................................................................................ 23 5.3 Extra Information............................................................................ 27 5.4 AMI BIOS Beep Code....................................................................... 29 5.5 Troubleshooting............................................................................... 30 Appendix: SPEC In Other Languages ...................................... 31 German.................................................................................................................. 32 French .................................................................................................................... 34 Italian..................................................................................................................... 36 Spanish................................................................................................................... 38 Portuguese............................................................................................................ 40 Polish...................................................................................................................... 42 Russian................................................................................................................... 44 Arabic..................................................................................................................... 46 Japanese................................................................................................................ 48

1.1 BEFORE YOU START Thank you for choosing our product. Before you start installing the motherboard, please make sure you follow the instructions below: „ Prepare a dry and stable working environment with sufficient lighting. „ Always disconnect the computer from power outlet before operation. „ Before you take the motherboard out from anti-static bag, ground yourself properly by touching any safely grounded appliance, or use grounded wrist strap to remove the static charge. „ Avoid touching the components on motherboard or the rear side of the board unless necessary. Hold the board on the edge, do not try to bend or flex the board. „ Do not leave any unfastened small parts inside the case after installation. Loose parts will cause short circuits which may damage the equipment. „ Keep the computer from dangerous area, such as heat source, humid air and water. 1.2 PACKAGE CHECKLIST HDD Cable X 1 Serial ATA Cable X 1 Rear I/O Panel for ATX Case X 1 Installation Guide X 1 Fully Setup Driver CD X 1 (full version manual files inside) FDD Cable X 1 (optional) USB 2.0 Cable X1 (optional) S/PDIF out Cable X 1 (optional) Serial ATA Power Cable X 1 (optional) Note: The package contents may be different due to area or your motherboard version.

AMD Athlon 64 / Athlon 64 FX / Athlon 64 x2 / Sempron / Phenom / Phenom II processors (Maximum Watt: 95W) AMD 64 Architecture enables 32 and 64 bit computing Supports Hyper Transport 3.0 and PowerNow FSB Support HyperTransport 3.0 Supports up to 5.2 GT/s Bandwidth Chipset GeForce 8200 Super I/O ITE 8718 Provides the most commonly used legacy Super I/O functionality Low Pin Count Interface Environment Control initiatives H/W Monitor ITE's "Smart Guardian" function Main Memory DDR2 DIMM Slots x 2 Max Memory Capacity 8GB Each DIMM supports 256MB/512MB/ 1GB/2GB/4GB DDR2 Dual Channel Mode DDR2 memory module Supports DDR2 533 / 667 / 800 Supports DDR2 1066 (by AM2+ / AM3 CPU) Registered DIMM and ECC DIMM is not supported Graphics Integrated in GeForce 8200 Chipset Max Shared Video Memory is 512MB DX10 / HDCP / PureVideo support IDE Integrated IDE Controller Ultra DMA 33 / 66 / 100 / 133 Bus Master Mode supports PIO Mode 0~4, SATA II Integrated Serial ATA Controller Data transfer rates up to 3 Gb/s SATA Version 2.0 specification compliant LAN Realtek RTL 8111DL 10 / 100 Mb/s / 1Gb/s auto negotiation Half / Full duplex capability Sound ALC662 5.1 channels audio out High Definition Audio PCI Express Gen2 x16 Slot x1 Supports PCI-E Gen2 x16 expansion cards Slots PCI Slot x2 Supports PCI expansion cards Floppy Connector x1 Each connector supports 2 Floppy drives IDE Connector x1 Each connector supports 2 IDE device SATA Connector x4 Each connector supports 1 SATA devices On Board Connectors Front Panel Connector x1 Supports front panel facilities

x1 Supports front panel audio function CD-in Connector x1 Supports CD audio-in function CPU Fan Header x1 CPU Fan power supply (with Smart Fan function) System Fan Header x1 System Fan Power supply CMOS clear Header x1 Restore CMOS data to factory default USB Connector x2 Each connector supports 2 front panel USB ports Power Connector (24pin) x1 Connects to Power supply Power Connector (4pin) x1 Connects to Power supply Printer Port Connector x1 Each connector supports 1 Printer port Serial port Connector x1 Connects to RS-232 Port Back Panel I/O PS/2 Keyboard x1 PS/2 Mouse x1 DVI port x1 VGA port x1 LAN port x1 USB Port x4 Audio Jack x3 Connects to PS/2 Keyboard Connects to PS/2 Mouse Connect to DVI-D monitor Connect to D-SUB monitor Connect to RJ-45 ethernet cable Connect to USB devices Provide Audio-In/Out and microphone connection Board Size 190 mm(W) x 244 mm(L) Special Features RAID 0 / 1 / 5 / 0+1 support Hybrid SLI support (by nVIDIA driver) OS Support Windows XP / Vista 32 / Vista 64 Biostar reserves the right to add or remove support for any OS With or without notice. 1.4 REAR PANEL CONNECTORS PS/2 Mouse PS/2 Keyboard USBX2 USBX2 LAN VGA Line In/ Surround Line Out Mic In 1/ Bass/ Center DVI-D

■ st pin.

2.1 INSTALLING CENTRAL PROCESSING UNIT (CPU) Step 1: Remove the socket protection cap. Step 2: Pull the lever toward direction A from the socket and then raise the lever up to a 90-degree angle. Step 3: Look for the white triangle on socket, and the gold triangle on CPU should point towards this white triangle. The CPU will fit only in the correct orientation.

B to complete the installation. Step 5: Put the CPU Fan on the CPU and buckle it. Connect the CPU FAN power cable to the JCFAN. This completes the installation. Note: Please update the BIOS to the latest version while using AM2+ / AM3 CPUs. Due to the latest CPU transition, you may encounter the situation that the new system failed to boot while using new AM2+ / AM3 CPUs. In this case, please install one standard AM2 CPU to boot your system, and update the latest BIOS from our website for AM2+ / AM3 CPUs support.

cable and connector may be different according to the fan manufacturer. Connect the fan cable to the connector while matching the black wire to pin#1. CPU_FAN1: CPU Fan Header Pin Assignment 1 Ground 2 +12V 3 FAN RPM rate sense 1 4 4 Smart Fan Control (By Fan) SYS_FAN1: System Fan Header Pin Assignment 1 Ground 2 +12V 1 3 3 FAN RPM rate sense Note: The CPU_FAN1 supports 4-pin head connector. The SYS_FAN1 supports 3-pin head connector. When connecting with wires onto connectors, please note that the red wire is the positive and should be connected to pin#2, and the black wire is Ground and should be connected to GND.

A. Memory Modules DIMMA1 DIMMB1 1. Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot such that the notch on the DIMM matches the break on the Slot. 2. Insert the DIMM vertically and firmly into the slot until the retaining chip snap back in place and the DIMM is properly seated.

DIMM Socket Location DDR2 Module Total Memory Size DIMMA1 256MB/512MB/1GB/2GB/4GB DIMMB1 256MB/512MB/1GB/2GB/4GB Max is 8GB. C. Dual Channel Memory installation Please refer to the following requirements to activate Dual Channel function: Install memory module of the same density in pairs, shown in the table. Dual Channel Status DIMMA1 DIMMB1 Disabled O X Disabled X O Enabled O O (O means memory installed, X means memory not installed.) The DRAM bus width of the memory module must be the same (x8 or x16)

FDD1: Floppy Disk Connector The motherboard provides a standard floppy disk connector that supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types. 1 33 2 34 IDE1: Hard Disk Connector The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality. 2 1 39 40 SATA1~SATA4: Serial ATA Connectors The motherboard has a PCI to SATA Controller with 4 channels SATA interface, it satisfies the SATA 2.0 spec and with transfer rate of 3.0Gb/s. Pin Assignment 1 Ground 2 TX+ 3 TX- 4 Ground 5 RX- 6 RX+ 1 4 7 SATA3 SATA4 SATA2 SATA1 7 Ground

- PCI-Express 2.0 compliant. - Maximum theoretical realized bandwidth of 8GB/s simultaneously per direction, for an aggregate of 16GB/s totally. - PCI-Express Gen2 supports a raw bit-rate of 5.0Gb/s on the data pins. - 2X bandwidth over the PCI-Express 1.0 architecture. PEX16_1 PCI1/PCI2: Peripheral Component Interconnect Slots This motherboard is equipped with 2 standard PCI slots. PCI stands for Peripheral Component Interconnect, and it is a bus standard for expansion cards. This PCI slot is designated as 32 bits. PCI1 PCI2

This connector allows user to connect 24-pin power connector on the ATX power supply. 1 12 13 24 Pin Assignment Pin Assignment 13 +3.3V 1 +3.3V 14 -12V 2 +3.3V 15 Ground 3 Ground 16 PS_ON 4 +5V 17 Ground 5 Ground 18 Ground 6 +5V 19 Ground 7 Ground 20 NC 8 PW_OK 21 +5V 9 Standby Voltage+5V 22 +5V 10 +12V 23 +5V 11 +12V 24 Ground 12 +3.3V ATXPWR2: ATX Power Source Connector Connecting this connector will provide +12V to CPU power circuit. Pin Assignment 1 +12V 2 +12V 3 Ground 1 2 3 4 4 Ground Note: Before power on the system, please make sure that both ATXPWR1 and ATXPWR2 connectors have been plugged-in.

3.1 HOW TO SETUP JUMPERS The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”, if not, that means the jumper is “open”. Pin opened Pin closed Pin1-2 closed 3.2 DETAIL SETTINGS PANEL1: Front Panel Header This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and speaker connection. It allows user to connect the PC case’s front panel switch functions. 1 8 16 PWR_LED On/Off RST HLED SPK + + + 9 - - Pin Assignment Function Pin Assignment Function 1 +5V 9 N/A 2 N/A 10 N/A N/A 3 N/A 11 N/A N/A 4 Speaker Speaker Connector 12 Power LED (+) 5 HDD LED (+) 13 Power LED (+) 6 HDD LED (-) Hard drive LED 14 Power LED (-) Power LED 7 Ground 15 Power button 8 Reset control Reset button 16 Ground Power-on button

This header allows user to connect the front audio output cable with the PC front panel. This header allows only HD audio front panel connector; AC’97 connector is not acceptable. Pin Assignment 1 Mic Left in 2 Ground 3 Mic Right in 4 GPIO 5 Right line in 6 Jack Sense 7 Front Sense 8 Key 9 Left line in 1 9 2 10 10 Jack Sense CD_IN1: CD-ROM Audio-in Connector This connector allows user to connect the audio source from the variaty devices, like CD-ROM, DVD-ROM, PCI sound card, PCI TV turner card etc. Pin Assignment 1 Left Channel Input 2 Ground 3 Ground 1 4 4 Right Channel Input

Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and the CMOS data. Please carefully follow the procedures to avoid damaging the motherboard. 1 3 Pin 1-2 Close: Normal Operation (Default). 1 3 1 3 Pin 2-3 Close: Clear CMOS data. ※ Clear CMOS Procedures: 1. Remove AC power line. 2. Set the jumper to “Pin 2-3 close”. 3. Wait for five seconds. 4. Set the jumper to “Pin 1-2 close”. 5. Power on the AC. 6. Reset your desired password or clear the CMOS data. F_COM1: Serial port Connector The motherboard has a Serial Port Connector for connecting RS-232 Port. Pin Assignment 1 Carrier detect 2 Received data 3 Transmitted data 4 Data terminal ready 5 Signal ground 6 Data set ready 7 Request to send 8 Clear to send 9 Ring indicator 1 9 2 10 10 NC

This header allows you to connect printer port on the PC. 1 25 2 Pin Assignment Pin Assignment 1 -Strobe 14 Ground 2 -ALF 15 Data 6 3 Data 0 16 Ground 4 -Error 17 Data 7 5 Data 1 18 Ground 6 -Init 19 -ACK 7 Data 2 20 Ground 8 -Scltin 21 Busy 9 Data 3 22 Ground 10 Ground 23 PE 11 Data 4 24 Ground 12 Ground 25 SCLT 13 Data 5 26 Key F_USB1/F_USB2: Headers for USB 2.0 Ports at Front Panel These headers allow user to connect additional USB cable on the PC front panel, and also can be connected with internal USB devices, like USB card reader. Pin Assignment 1 +5V (fused) 2 +5V (fused) 3 USB- 4 USB- 5 USB+ 6 USB+ 7 Ground 8 Ground 9 NC 1 9 2 10 F F _USB1 _USB2 10 Key

Pin 1-2 Close: JUSBV1: +5V for USB ports at USB1/RJ45USB1. JUSBV2: +5V for USB ports at front panel (F_USB1/F_USB2). Pin 2-3 Close: JUSBV1: +5V STB for USB ports at USB1/ RJ45USB1. JUSBV2: +5V STB for USB ports at front panel (F_USB1/F_USB2). 1 3 Pin 1-2 close 1 3 JUSBV1 3 1 JUSBV2 1 3 Pin 2-3 close JKB_PWR1: Power Source Header for PS/2 Keyboard and Mouse 1 3 Pin 1-2 close +5V for PS/2 keyboard and mouse. 1 3 1 3 Pin 2-3 close +5V STB for PS/2 keyboard and mouse.

4.1 OPERATING SYSTEM Supports Windows XP Home/Professional Edition, and Windows Vista 32 / 64. 4.2 RAID ARRAYS RAID supports the following types of RAID arrays: RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for many applications. RAID 1: RAID 1 defines techniques for mirroring data. RAID 0+1: RAID 0+1 combines the techniques used in RAID 0 and RAID 1. RAID 5: RAID 5 provides fault tolerance and better utilization of disk capacity. 4.3 HOW RAID WORKS RAID 0: The controller “stripes” data across multiple drives in a RAID 0 array system. It breaks up a large file into smaller blocks and performs disk reads and writes across multiple drives in parallel. The size of each block is determined by the stripe size parameter, which you set during the creation of the RAID set based on the system environment. This technique reduces overall disk access time and offers high bandwidth. Features and Benefits - Drives: Minimum 2, and maximum is up to 6 or 8. Depending on the platform. - Uses: Intended for non-critical data requiring high data throughput, or any environment that does not require fault tolerance. - Benefits: provides increased data throughput, especially for large files. No capacity loss penalty for parity. - Drawbacks: Does not deliver any fault tolerance. If any drive in the array fails, all data is lost. - Fault Tolerance: No. Block 1 Block 3 Block 5 Block 2 Block 4 Block 6

array system. The mirrored (backup) copy of the data can reside on the same disk or on a second redundant drive in the array. RAID 1 provides a hot-standby copy of data if the active volume or drive is corrupted or becomes unavailable because of a hardware failure. RAID techniques can be applied for high-availability solutions, or as a form of automatic backup that eliminates tedious manual backups to more expensive and less reliable media. Features and Benefits - Drives: Minimum 2, and maximum is 2. - Uses: RAID 1 is ideal for small databases or any other application that requires fault tolerance and minimal capacity. - Benefits: Provides 100% data redundancy. Should one drive fail, the controller switches to the other drive. - Drawbacks: Requires 2 drives for the storage space of one drive. Performance is impaired during drive rebuilds. - Fault Tolerance: Yes. Block 1 Block 2 Block 3 Block 1 Block 2 Block 3

solution for improved performance plus resiliency. Features and Benefits - Drives: Minimum 4, and maximum is 6 or 8, depending on the platform. - Benefits: Optimizes for both fault tolerance and performance, allowing for automatic redundancy. May be simultaneously used with other RAID levels in an array, and allows for spare disks. - Drawbacks: Requires twice the available disk space for data redundancy, the same as RAID level 1. - Fault Tolerance: Yes. Block 2 Block 4 Block 6 Block 1 Block 3 Block 5 Block 2 Block 4 Block 6 Block 1 Block 3 Block 5 GeForce 8200

data and parity blocks across all the drives in the array. Fault tolerance is maintained by ensuring that the parity information for any given block of data is placed on a different drive from those used to store the data itself. Features and Benefits - Drives: Minimum 3. - Uses: RAID 5 is recommended for transaction processing and general purpose service. - Benefits: An ideal combination of good performance, good fault tolerance, and high capacity and storage efficiency. - Drawbacks: Individual block data transfer rate same as a single disk. Write performance can be CPU intensive. - Fault Tolerance: Yes. Disk 1 DATA 3 PARITY DATA 7 DATA 1 DATA 9 PARITY Disk 2 PARITY DATA 5 DATA 8 DATA 2 PARITY DATA 11 Disk 3 DATA 4 DATA 6 PARITY PARITY DATA 10 DATA 12 GeForce 8200 ※ For more detailed setup information, please refer to the Driver CD, or go to http://www.nvidia.com/object/IO_28159.html to download the NVIDIA RAID User’s Guide.

5.1 DRIVER INSTALLATION NOTE After you installed your operating system, please insert the Fully Setup Driver CD into your optical drive and install the driver for better system performance. You will see the following window after you insert the CD The setup guide will auto detect your motherboard and operating system. Note: If this window didn’t show up after you insert the Driver CD, please use file browser to locate and execute the file SETUP.EXE under your optical drive. A. Driver Installation To install the driver, please click on the Driver icon. The setup guide will list the compatible driver for your motherboard and operating system. Click on each device driver to launch the installation program. B. Software Installation To install the software, please click on the Software icon. The setup guide will list the software available for your system, click on each software title to launch the installation program. C. Manual Aside from the paperback manual, we also provide manual in the Driver CD. Click on the Manual icon to browse for available manual. Note: You will need Acrobat Reader to open the manual file. Please download the latest version of Acrobat Reader software from http://www.adobe.com/products/acrobat/readstep2.html

would appear if the Autorun function has been enabled. 2. Select Software Installation, and then click on the respective software title. 3. Follow the on-screen instructions to complete the installation. Launching Software After the installation process, you will see the software icon “eHOT Line” / “BIOS Update” appears on the desktop. Double-click the icon to launch the utility. eHot-Line (Optional) eHot-Line is a convenient utility that helps you to contact with our Tech-Support system. This utility will collect the system information which is useful for analyzing the problem you may have encountered, and then send these information to our tech-support department to help you fix the problem. Before you use this utility, please set Outlook Express as your default e-mail client application program. This block will show the information which would be collected in the mail. Provide the e-mail address that you would like to send the copy to. Provide the name of the power supply manufacturer and the model no. Send the mail out. Save these information to a .txt file Exit this dialog. Select your area or the area close to you. * Provide the name of the memory module manufacturer. * Describe condition of your system. * * represents important information that you must provide. Without this information, you may not be able to send out the mail.

to send the mail out. A warning dialog would appear asking for your confirmation; click “Send” to confirm or “Do Not Send” to cancel. If you want to save this information to a .txt file, click “Save As…” and then you will see a saving dialog appears asking you to enter file name. Enter the file name and then click “Save”. Your system information will be saved to a .txt file. Open the saved .txt file, you will see your system information including motherboard/BIOS/CPU/video/ device/OS information. This information is also concluded in the sent mail. We will not share customer’s data with any other third parties, so please feel free to provide your system information while using eHot-Line service. If you are not using Outlook Express as your default e-mail client application, you may need to save the system information to a .txt file and send the file to our tech support with other e-mail application. Go to the following web http://www.biostar.com.tw/app/en-us/about/contact.php for getting our contact information.

motherboard BIOS under Windows system. Update BIOS with a BIOS file Clear CMOS function (Only for AWARD BIOS) Show current BIOS information Save current BIOS to a .bin file AWARD BIOS AMI BIOS Once click on this button, the saving dialog will show. Choose the position to save file and enter file name. (We recommend that the file name should be English/number and no longer than 7 characters.) Then click Save. After the saving process, finish dialog will show. Click on OK to complete the BIOS Backup procedure.

For AWARD BIOS, update BIOS procedure should be run with Clear CMOS function, so please check on Clear CMOS first. Then click Update BIOS button, a dialog will show for asking you backup current BIOS. Click Yes for BIOS backup and refer to the Backup BIOS procedure; or click No to skip this procedure. After the BIOS Backup procedure, the open dialog will show for requesting the BIOS file which is going to be updated. Please choose the proper BIOS file for updating, then click on Open. The utility will update BIOS with the proper BIOS file, and this process may take minutes. Please do not open any other applications during this process. After the BIOS Update process, click on OK to restart the system. While the system boots up and the full screen logo shows, press key to enter BIOS setup. In the BIOS setup, use the Load Optimized Defaults function and then Save and Exit Setup to exit BIOS setup. BIOS Update is completed. All the information and content above about the software are subject to be changed without notice. For better performance, the software is being continuously updated. The information and pictures described above are for your reference only. The actual information and settings on board may be slightly different from this manual.

seconds, that means the CPU protection function has been activated. When the CPU is over heated, the motherboard will shutdown automatically to avoid a damage of the CPU, and the system may not power on again. In this case, please double check: 1. The CPU cooler surface is placed evenly with the CPU surface. 2. CPU fan is rotated normally. 3. CPU fan speed is fulfilling with the CPU speed. After confirmed, please follow steps below to relief the CPU protection function. 1. Remove the power cord from power supply for seconds. 2. Wait for seconds. 3. Plug in the power cord and boot up the system. Or you can: 1. Clear the CMOS data. (See “Close CMOS Header: JCMOS1” section) 2. Wait for seconds. 3. Power on the system again.

update your BIOS via USB pen drive or floppy disk. The BIO-Flasher is built in the BIOS chip. To enter the utility, press during the Power-On Self Tests (POST) procedure while booting up. Updating BIOS with BIO-Flasher 1. Go to the website to download the latest BIOS file for the motherboard. 2. Then, save the BIOS file into a USB pen drive or a floppy disk. 3. Insert the USB pen drive or the floppy disk that contains the BIOS file to the USB port or the floppy disk drive. 4. Power on or reset the computer and then press during the POST process. A select dialog as the picture on the right appears. Select the device contains the BIOS file and press to enter the utility. 5. The utility will show the BIOS files and their respective information. Select the proper BIOS file and press then to perform the BIOS update process. 6. After the update process, the utility will ask you to reboot the system. Press to proceed. BIOS update completes. z This utility only allows storage device with FAT32/16 format and single partition. z Shutting down or resetting the system while updating the BIOS will lead to system boot failure.

Boot Block Beep Codes Number of Beeps Description 1 No media present. (Insert diskette in floppy drive A:) 2 “AMIBOOT.ROM” file not found in root directory of diskette in A: 3 Insert next diskette if multiple diskettes are used for recovery 4 Flash Programming successful 5 File read error 7 No Flash EPROM detected 10 Flash Erase error 11 Flash Program error 12 “AMIBOOT.ROM” file size error 13 BIOS ROM image mismatch (file layout does not match image present in flash device) POST BIOS Beep Codes Number of Beeps Description 1 Memory refresh timer error 3 Base memory read/write test error 6 Keyboard controller BAT command failed 7 General exception error (processor exception interrupt error) 8 Display memory error (system video adapter) Troubleshooting POST BIOS Beep Codes Number of Beeps Troubleshooting Action 1, 3 Reseat the memory, or replace with known good modules. 6, 7 Fatal error indicating a serious problem with the system. Consult your system manufacturer. Before declaring the motherboard beyond all hope, eliminate the possibility of interference by a malfunctioning add-in card. Remove all expansion cards except the video adapter. z If beep codes are generated when all other expansion cards are absent, consult your system manufacturer’s technical support. z If beep codes are not generated when all other expansion cards are absent, one of the add-in cards is causing the malfunction. Insert the cards back into the system one at a time until the problem happens again. This will reveal the malfunctioning card. 8 If the system video adapter is an add-in card, replace or reseat the video adapter. If the video adapter is an integrated part of the system board, the board may be faulty.

Power LED does not shine; the fan of the power supply does not work 2. Indicator light on keyboard does not shine. 1. Make sure power cable is securely plugged in. 2. Replace cable. 3. Contact technical support. System is inoperative. Keyboard lights are on, power indicator lights are lit, and hard drives are running. Using even pressure on both ends of the DIMM, press down firmly until the module snaps into place. System does not boot from a hard disk drive, but can be booted from optical drive. 1. Check cable running from disk to disk controller board. Make sure both ends are securely plugged in; check the drive type in the standard CMOS setup. 2. Backing up the hard drive is extremely important. All hard disks are capable of breaking down at any time. System only boots from an optical drive. Hard disks can be read, applications can be used, but system fails to boot from a hard disk. 1. Back up data and applications files. 2. Reformat the hard drive. Re-install applications and data using backup disks. Screen message shows “Invalid Configuration” or “CMOS Failure.” Review system’s equipment. Make sure correct information is in setup. System cannot boot after user installs a second hard drive. 1. Set master/slave jumpers correctly. 2. Run SETUP program and select correct drive types. Call the drive manufacturers for compatibility with other drives.

GERMAN Spezifikationen CPU Sockel AM2+ / AM3 AMD Athlon 64 / Athlon 64 FX / Althlon 64 X2 / Sempron / Phenom / Phenom II Prozessoren (Maximales Watt: 95W) Die AMD 64-Architektur unterstützt eine 32-Bit- und 64-Bit-Datenverarbeitung Unterstützt Hyper Transport 3.0 und PowerNow FSB Unterstützt HyperTransport 3.0 mit einer Bandbreite von bis zu 5.2 GT/s Chipsatz GeForce 8200 Super E/A ITE8718 Bietet die häufig verwendeten alten Super E/A-Funktionen. Low Pin Count-Schnittstelle Umgebungskontrolle, Hardware-Überwachung "Smart Guardian"-Funktion von ITE Arbeitsspeich er DDR2 DIMM-Steckplätze x 2 Max. 8GB Arbeitsspeicher Jeder DIMM unterstützt 256MB/512MB/ 1GB/2GB/4GB DDR2. Dual-Kanal DDR2 Speichermodul Unterstützt DDR2 533 / 667 / 800 Unterstützt DDR2 1066 (by AM2+ / AM3 CPU) registrierte DIMMs. ECC DIMMs werden nicht unterstützt. Grafik Integrierter GeForce 8200-Chipsatz Max. 512MB gemeinsam benutzter Videospeicher Unterstützt DX10 / HDCP / PureVideo IDE Integrierter IDE-Controller Ultra DMA 33 / 66 / 100 / 133 Bus Master-Modus Unterstützt PIO-Modus 0~4, SATA Integrierter Serial ATA-Controller Datentransferrate bis zu 3 Gb/s Konform mit der SATA-Spezifikation Version 2.0. LAN Realtek RTL 8111DL 10 / 100 / 1000 Mb/s Auto-Negotiation Halb-/ Vollduplex-Funktion HD Audio-Unters tützung ALC662 5.1-Kanal-Audioausgabe Unterstützt High-Definition Audio

x1 Steckplätze PCI-Steckplatz x2 Diskettenlaufwerkanschluss x1 Jeder Anschluss unterstützt 2 Diskettenlaufwerke IDE-Anschluss x1 Jeder Anschluss unterstützt 2 IDE-Laufwerke SATA-Anschluss x4 Jeder Anschluss unterstützt 1 SATA-Laufwerk Fronttafelanschluss x1 Unterstützt die Fronttafelfunktionen Front-Audioanschluss x1 Unterstützt die Fronttafel-Audioanschlussfunktion CD-IN-Anschluss x1 Unterstützt die CD Audio-In-Funktion CPU-Lüfter-Sockel x1 CPU-Lüfterstromversorgungsanschluss (mit Smart Fan-Funktion) System-Lüfter-Sockel x1 System-Lüfter-Stromversorgungsanschluss "CMOS löschen"-Sockel x1 USB-Anschluss x2 Jeder Anschluss unterstützt 2 Fronttafel-USB-Anschlüsse Stromanschluss (24-polig) x1 Stromanschluss (4-polig) x1 Druckeranschluss Anschluss x1 Jeder Anschluss unterstützt 1 Druckeranschluss Onboard-Ans chluss Serieller Anschluss x1 Rückseiten-E /A PS/2-Tastatur x1 PS/2-Maus x1 VGA-Anschluss x1 LAN-Anschluss x1 USB-Anschluss x4 Audioanschluss x3 DVI-Anschluss x1 Platinengröß e 190 mm (B) X 244 mm (L) Sonderfunkti onen Unterstützt RAID 0 / 1 / 5 / 0+1 Unterstützt Hybrid SLI (by nVIDIA driver) OS-Unterstü tzung Windows XP / Vista 32 / Vista 64 Biostar behält sich das Recht vor, ohne Ankündigung die Unterstützung für ein Betriebssystem hinzuzufügen oder zu entfernen.

Processeurs AMD Athlon 64 / Athlon 64 FX / Althlon 64 X2 / Sempron / Phenom / Phenom II (Watt maximum : 95W) L'architecture AMD 64 permet le calcul 32 et 64 bits Prend en charge Hyper Transport 3.0 et PowerNow Bus frontal Prend en charge Hyper Transport 3.0 jusqu'à une bande passante de 5.2 GT/s Chipset GeForce 8200 Super E/S ITE 8718 Fournit la fonctionnalité de Super E/S patrimoniales la plus utilisée. Interface à faible compte de broches Initiatives de contrôle environnementales, Moniteur de matériel Fonction "Gardien intelligent" de l'ITE Mémoire principale Fentes DDR2 DIMM x 2 Capacité mémoire maximale de 8 Go Chaque DIMM prend en charge des DDR2 de 256Mo/512Mo/1Go/2Go/4Go Module de mémoire DDR2 à mode à double voie Prend en charge la DDR2 533 / 667 / 800 Prend en charge la DDR2 1066 (by AM2+ / AM3 CPU) Les DIMM à registres et DIMM avec code correcteurs d'erreurs ne sont pas prises en charge Graphiques Integré dans la chipset GeForce 8200 Mémoire vidéo partagée maximale de 512 Mo Prise en charge DX10 / HDCP / PureVideo IDE Contrôleur IDE intégré Mode principale de Bus Ultra DMA 33 / 66 / 100 / 133 Prend en charge le mode PIO 0~4, SATA Contrôleur Serial ATA intégré Taux de transfert jusqu'à 3 Go/s. Conforme à la spécification SATA Version 2.0 LAN Realtek RTL 8111DL 10 / 100 / 1000 Mb/s négociation automatique Half / Full duplex capability Prise en charge audio HD ALC662 Sortie audio à 5.1 voies Prise en charge de l'audio haute définition Fente PCI Express Gen2 x16 x1 Fentes Fente PCI x2 Connecteur de disquette x1 Chaque connector prend en charge 2 lecteurs de disquettes Connecteur IDE x1 Chaque connecteur prend en charge 2 périphériques IDE Connecteur embarqué Connecteur SATA x4 Chaque connecteur prend en charge 1 périphérique SATA

x1 Prend en charge les équipements du panneau avant Connecteur Audio du panneau avant x1 Prend en charge la fonction audio du panneau avant Connecteur d'entrée CD x1 Prend en charge la fonction d'entrée audio de CD Embase de ventilateur UC x1 Alimentation électrique du ventilateur UC (avec fonction de ventilateur intelligent) Embase de ventilateur système x1 Alimentation électrique du ventilateur système Embase d'effacement CMOS x1 Connecteur USB x2 Chaque connecteur prend en charge 2 ports USB de panneau avant Connecteur d'alimentation x1 (24 broches) Connecteur d'alimentation x1 (4 broches) Connecteur de Port d'imprimante x1 Chaque connector prend en charge 1 Port d'imprimante Connecteur de Port série x1 E/S du panneau arrière Clavier PS/2 x1 Souris PS/2 x1 Port VGA x1 Port LAN x1 Port USB x4 Fiche audio x3 Port DVI x1 Dimension s de la carte 190 mm (l) X 244 mm (H) Fonctionnal ités spéciales Prise en charge RAID 0 / 1 / 5 / 0+1 Prise en charge Hybrid SLI (by nVIDIA driver) Support SE Windows XP / Vista 32 / Vista 64 Biostar se réserve le droit d'ajouter ou de supprimer le support de SE avec ou sans préavis.

Processori AMD Athlon 64 / Athlon 64 FX / Althlon 64 X2 / Sempron / Phenom / Phenom II (Watt massimo: 95W) L’architettura AMD 64 abilita la computazione 32 e 64 bit Supporto di Hyper Transport 3.0 e PowerNow FSB Supporto di HyperTransport 3.0 fino a 5.2 GT/s di larghezza di banda Chipset GeForce 8200 Super I/O ITE 8718 Fornisce le funzionalità legacy Super I/O usate più comunemente. Interfaccia LPC (Low Pin Count) Funzioni di controllo dell’ambiente: Monitoraggio hardware Funzione "Smart Guardian" di ITE Memoria principale Alloggi DIMM DDR2 x 2 Capacità massima della memoria 8GB Ciascun DIMM supporta DDR2 256MB/512MB/1GB/2GB/4GB Modulo di memoria DDR2 a canale doppio Supporto di DDR2 533 / 667 / 800 Supporto di DDR2 1066 (by AM2+ / AM3 CPU) DIMM registrati e DIMM ECC non sono supportati Grafica Integrata nel Chipset GeForce 8200 La memoria video condivisa massima è di 512 MB Supporto DX10 / HDCP / PureVideo IDE Controller IDE integrato Modalità Bus Master Ultra DMA 33 / 66 / 100 / 133 Supporto modalità PIO Mode 0-4 SATA Controller Serial ATA integrato Velocità di trasferimento dei dati fino a 3 Gb/s. Compatibile specifiche SATA Versione 2.0. LAN Realtek RTL 8111DL Negoziazione automatica 10 / 100 / 1000 Mb/s Capacità Half / Full Duplex Supporto audio HD ALC662 Uscita audio 5.1 canali Supporto audio High-Definition (HD) Alloggio PCI Express Gen2 x16 x1 Alloggi Alloggio PCI x2 Connettore floppy x1 Ciascun connettore supporta 2 unità Floppy Connettori su scheda Connettore IDE x1 Ciascun connettore supporta 2 unità IDE

Connettore pannello frontale x1 Supporta i servizi del pannello frontale Connettore audio frontale x1 Supporta la funzione audio pannello frontale Connettore CD-in x1 Supporta la funzione input audio CD Collettore ventolina CPU x1 Alimentazione ventolina CPU (con funzione Smart Fan) Collettore ventolina sistema x1 Alimentazione ventolina di sistema Collettore cancellazione CMOS x1 Connettore USB x2 Ciascun connettore supporta 2 porte USB pannello frontale Connettore alimentazione x1 (24 pin) Connettore alimentazione x1 (4 pin) Connettore Porta stampante x1 Ciascun connettore supporta 1 Porta stampante Connettore Porta seriale x1 I/O pannello posteriore Tastiera PS/2 x1 Mouse PS/2 x1 Porta VGA x1 Porta LAN x1 Porta USB x4 Connettore audio x3 Porta DVI x1 Dimension i scheda 190 mm (larghezza) x 244 mm (altezza) Caratterist iche speciali Supporto RAID 0 / 1 / 5 / 0+1 Supporto Hybrid SLI (by nVIDIA driver) Sistemi operativi supportati Windows XP / Vista 32 / Vista 64 Biostar si riserva il diritto di aggiungere o rimuovere il supporto di qualsiasi sistema operativo senza preavviso.

Procesadores AMD Athlon 64 / Athlon 64 FX / Athlon 64 X2 / Sempron / Phenom / Phenom II (Vatio máximo: 95W) La arquitectura AMD 64 permite el procesado de 32 y 64 bits Soporta las tecnologías Hyper Transport 3.0 y PowerNow FSB Admite HyperTransport 3.0 con un ancho de banda de hasta 5.2 GT/s Conjunto de chips GeForce 8200 Súper E/S ITE 8718 Le ofrece las funcionalidades heredadas de uso más común Súper E/S. Interfaz de cuenta Low Pin Iniciativas de control de entorno, Monitor hardware Función "Guardia inteligente" de ITE Memoria principal Ranuras DIMM DDR2 x 2 Capacidad máxima de memoria de 8GB Cada DIMM admite DDR de 256MB/ 512MB/1GB/2GB/4GB Módulo de memoria DDR2 de canal Doble Admite DDR2 de 533 / 667 / 800 Admite DDR2 de 1066 (by AM2+ / AM3 CPU) No admite DIMM registrados o DIMM compatibles con ECC Gráficos Integrados en el conjunto de chips GeForce 8200 Memoria máxima de vídeo compartida de 512 MB Admite DX10 / HDCP / PureVideo IDE Controlador IDE integrado Modo bus maestro Ultra DMA 33 / 66 / 100 / 133 Soporte los Modos PIO 0~4, SATA Controlador ATA Serie Integrado Tasas de transferencia de hasta 3 Gb/s. Compatible con la versión SATA 2.0. Red Local Realtek RTL 8111DL Negociación de 10 / 100 / 1000 Mb/s Funciones Half / Full dúplex Soporte de sonido HD ALC662 Salida de sonido de 5.1 canales Soporte de sonido Alta Definición Ranura PCI Express Gen2 x16 X1 Ranuras Ranura PCI X2 Conector disco flexible X1 Cada conector soporta 2 unidades de disco flexible Conectores en placa Conector IDE X1 Cada conector soporta 2 dispositivos IDE

Conector de panel frontal X1 Soporta instalaciones en el panel frontal Conector de sonido frontal X1 Soporta funciones de sonido en el panel frontal Conector de entrada de CD X1 Soporta función de entrada de sonido de CD Cabecera de ventilador de CPU X1 Fuente de alimentación de ventilador de CPU (con función Smart Fan) Cabecera de ventilador de sistema X1 Fuente de alimentación de ventilador de sistema Cabecera de borrado de CMOS X1 Conector USB X2 Cada conector soporta 2 puertos USB frontales Conector de alimentación X1 (24 patillas) Conector de alimentación X1 (4 patillas) Conector Puerto de impresora X1 Cada conector soporta 1 Puerto de impresora Conector Puerto serie X1 Panel trasero de E/S Teclado PS/2 X1 Ratón PS/2 X1 Puerto VGA X1 Puerto de red local X1 Puerto USB X4 Conector de sonido X3 Puerto DVI X1 Tamaño de la placa 190 mm. (A) X 244 Mm. (H) Funciones especiales Admite RAID 0 / 1 / 5 / 0+1 Admite Hybrid SLI (by nVIDIA driver) Soporte de sistema operativo Windows XP / Vista 32 / Vista 64 Biostar se reserva el derecho de añadir o retirar el soporte de cualquier SO con o sin aviso previo.

Processadores AMD Athlon 64 / Athlon 64 FX / Althlon 64 X2 / Sempron / Phenom / Phenom II (Watt máximo: 95W) A arquitectura AMD 64 permite uma computação de 32 e 64 bits Suporta as tecnologias Hyper Transport 3.0 e PowerNow FSB Suporta a tecnologia HyperTransport 3.0 com uma largura de banda até 5.2 GT/s Chipset GeForce 8200 Especificaç ão Super I/O ITE 8718 Proporciona as funcionalidades mais utilizadas em termos da especificação Super I/O. Interface LPC (Low Pin Count). Iniciativas para controlo do ambiente Monitorização do hardware Função "Smart Guardian" da ITE Memória principal Ranhuras DIMM DDR2 x 2 Capacidade máxima de memória: 8 GB Cada módulo DIMM suporta uma memória DDR2 de 256MB/512MB/ 1GB/2GB/4GB Módulo de memória DDR2 de canal duplo Suporta módulos DDR2 533 / 667 / 800 Suporta módulos DDR2 1066 (by AM2+ / AM3 CPU) Os módulos DIMM registados e os DIMM ECC não são suportados Placa gráfica Integrada no chipset GeForce 8200 Memória de vídeo máxima partilhada: 512 MB Suporta as funções DX10 / HDCP / PureVideo IDE Controlador IDE integrado Modo Bus master Ultra DMA 33 / 66 / 100 / 133 Suporta o modo PIO 0~4, SATA Controlador Serial ATA integrado Velocidades de transmissão de dados até 3 Gb/s. Compatibilidade com a especificação SATA versão 2.0. LAN Realtek RTL 8111DL Auto negociação de 10 / 100 / 1000 Mb/s Capacidade semi/full-duplex Suporte para áudio de alta definição ALC662 Saída de áudio de 5.1 canais Suporta a especificação High-Definition Audio Ranhura PCI Express Gen2 x16 x1 Ranhuras Ranhura PCI x2 Conector da unidade de disquetes x1 Cada conector suporta 2 unidades de disquetes Conector IDE x1 Cada conector suporta 2 dispositivos IDE Conectores na placa Conector SATA x4 Cada conector suporta 1 dispositivo SATA

x1 Para suporte de várias funções no painel frontal Conector de áudio frontal x1 Suporta a função de áudio no painel frontal Conector para entrada de CDs x1 Suporta a entrada de áudio a partir de CDs Conector da ventoinha da CPU x1 Alimentação da ventoinha da CPU (com a função Smart Fan) Conector da ventoinha do sistema x1 Alimentação da ventoinha do sistema Conector para limpeza do CMOS x1 Conector USB x2 Cada conector suporta 2 portas USB no painel frontal Conector de alimentação x1 (24 pinos) Conector de alimentação x1 (4 pinos) Conector da para impressora x1 Cada conector suporta 1 Porta para impressora Conector da Porta série x1 Entradas/S aídas no painel traseiro Teclado PS/2 x1 Rato PS/2 x1 Porta VGA x1 Porta LAN x1 Porta USB x4 Tomada de áudio x3 Porta DVI x1 Tamanho da placa 190 mm (L) X 244 mm (A) Característi cas especiais Suporta as funções RAID 0 / 1 / 5 / 0+1 Suporta as funções Hybrid SLI (by nVIDIA driver) Sistemas operativos suportados Windows XP / Vista 32 / Vista 64 A Biostar reserva-se o direito de adicionar ou remover suporte para qualquer sistema operativo com ou sem aviso prévio.

AMD Athlon 64 / Athlon 64 FX / Althlon 64 X2 / Sempron / Phenom / Phenom II Procesory (Maksymalny Watt: 95W) Architektura AMD 64 umożliwia przetwarzanie 32 i 64 bitowe Obsługa Hyper Transport 3.0 oraz PowerNow FSB Obsługa HyperTransport 3.0 o szerokości pasma do 5.2 GT/s Chipset GeForce 8200 Pamięć główna Gniazda DDR2 DIMM x 2 Maks. wielkość pamięci 8GB Każde gniazdo DIMM obsługuje moduły 256MB/512MB/1GB/2GB/4GB DDR2 Moduł pamięci DDR2 z trybem podwójnego kanału Obsługa DDR2 533 / 667 / 800 Obsługa DDR2 1066 (by AM2+ / AM3 CPU) Brak obsługi Registered DIMM oraz ECC DIMM Super I/O ITE 8718 Zapewnia najbardziej powszechne funkcje Super I/O. Interfejs Low Pin Count Funkcje kontroli warunków pracy, Monitor H/W Funkcja ITE "Smart Guardian" Grafika Zintegrowana w chipsecie GeForce 8200 Maks. wielkość współdzielonej pamięci video wynosi 512 MB Obsługa DX10 / HDCP / PureVideo IDE Zintegrowany kontroler IDE Ultra DMA 33 / 66 / 100 / 133 Tryb Bus Master obsługa PIO tryb 0~4, SATA Zintegrowany kontroler Serial ATA Transfer danych do 3 Gb/s. Zgodność ze specyfikacją SATA w wersji 2.0. LAN Realtek RTL 8111DL 10 / 100 / 1000 Mb/s z automatyczną negocjacją szybkości Działanie w trybie połowicznego / pełnego dupleksu Obsługa audio HD ALC662 5.1 kanałowe wyjście audio Obsługa High-Definition Audio Gniazdo PCI Express Gen2 x16 x1 Gniazda Gniazdo PCI x2 Złącze napędu dyskietek x1 Każde złącze obsługuje 2 napędy dyskietek Złącze IDE x1 Każde złącze obsługuje 2 urządzenia IDE Złącza wbudowan e Złącze SATA x4 Każde złącze obsługuje 1 urządzenie SATA

x1 Obsługa elementów panela przedniego Przednie złącze audio x1 Obsługa funkcji audio na panelu przednim Złącze wejścia CD x1 Obsługa funkcji wejścia audio CD Złącze główkowe wentylatora procesora x1 Zasilanie wentylatora procesora (z funkcją Smart Fan) Złącze główkowe wentylatora systemowego x1 Zasilanie wentylatora systemowego Złącze główkowe kasowania CMOS x1 Złącze USB x2 Każde złącze obsługuje 2 porty USB na panelu przednim Złącze zasilania (24 pinowe) x1 Złącze zasilania (4 pinowe) x1 Złącze Port drukarki x1 Każde złącze obsługuje 1 Port drukarki Złącze Port szeregowy x1 Back Panel I/O Klawiatura PS/2 x1 Mysz PS/2 x1 Port VGA x1 Port LAN x1 Port USB x4 Gniazdo audio x3 Port DVI x1 Wymiary płyty 190 mm (S) X 244 mm (W) Funkcje specjalne Obsługa RAID 0 / 1 / 5 / 0+1 Obsługa Hybrid SLI (by nVIDIA driver) Obsluga systemu operacyjne go Windows XP / Vista 32 / Vista 64 Biostar zastrzega sobie prawo dodawania lub odwoływania obsługi dowolnego systemu operacyjnego bez powiadomienia.

Процессоры AMD Athlon 64 / Athlon 64 FX / Althlon 64 X2 / Sempron / Phenom / Phenom II (Максимальный ватт: 95W) Архитектура AMD 64 разрешать обработка данных на 32 и 64 бит Поддержка Hyper Transport 3.0 и PowerNow FSB Поддержка HyperTransport 3.0 с пропускной способностью до 5.2 GT/s Набор микросхем GeForce 8200 Основная память Слоты DDR2 DIMM x 2 Максимальная ёмкость памяти 8 ГБ Каждый модуль DIMM поддерживает 256МБ/512МБ/1ГБ/2ГБ/4ГБ DDR2 Модуль памяти с двухканальным режимом DDR2 Поддержка DDR2 533 / 667 / 800 Поддержка DDR2 1066 (by AM2+ / AM3 CPU) Не поддерживает зарегистрированные модули DIMM and ECC DIMM Super I/O ITE 8718 Обеспечивает наиболее используемые действующие функциональные возможности Super I/O. Интерфейс с низким количеством выводов Инициативы по охране окружающей среды, Аппаратный монитор Функция ITE "Smart Guardian" (Интеллектуальная защита) Графика Встроенная в набор микросхем GeForce 8200 Максимальная совместно используемая видео память составляет 512 МБ Поддержка DX10 / HDCP / PureVideo IDE Встроенное устройство управления встроенными интерфейсами устройств Режим "хозяина" шины Ultra DMA 33 / 66 / 100 / 133 Поддержка режима PIO 0~4, SATA Встроенное последовательное устройство управления ATA скорость передачи данных до 3 гигабит/с. Соответствие спецификации SATA версия 2.0. Локальная сеть Realtek RTL 8111DL Автоматическое согласование 10 / 100 / 1000 Мб/с Частичная / полная дуплексная способность Звуковая поддержка жесткого диска ALC662 Звуковая поддержка High-Definition 5.1канальный звуковой выход Слот PCI Express Gen2 x16 x1 Слоты Слот PCI x2 Разъём НГМД x1 Каждый разъём поддерживает 2 накопителя на гибких магнитных дисках Встроенны й разъём Разъём IDE x1 Каждый разъём поддерживает 2 встроенных интерфейса накопителей

Разъём на лицевой панели x1 Поддержка устройств на лицевой панели Входной звуковой разъём x1 Поддержка звуковых функций на лицевой панели Разъём ввода для CD x1 Поддержка функции ввода для CD Контактирующее приспособление вентилятора центрального процессора x1 Источник питания для вентилятора центрального процессора (с функцией интеллектуального вентилятора) Контактирующее приспособление вентилятора системы x1 Источник питания для вентилятора системы Открытое контактирующее приспособление CMOS x1 USB-разъём x2 Каждый разъём поддерживает 2 USB-порта на лицевой панели Разъем питания (24 вывод) x1 Разъем питания (4 вывод) x1 Разъём Порт подключения принтера x1 Каждый разъём поддерживает 1 Порт подключения принтера Разъём Последовательный порт x1 Задняя панель средств ввода-выв ода Клавиатура PS/2 x1 Мышь PS/2 x1 Порт VGA x1 Порт LAN x1 USB-порт x4 Гнездо для подключения наушников x3 Порт DVI x1 Размер панели 190 мм (Ш) X 244 мм (В) Специальн ые техническ ие характери стики Поддержка RAID 0 / 1 / 5 / 0+1 Поддержка Hybrid SLI (by nVIDIA driver) Поддержк а OS Windows XP / Vista 32 / Vista 64 Biostar сохраняет за собой право добавлять или удалять средства обеспечения для OS с или без предварительного уведомления.

إﺟﺮاء اﻟﻌﻤﻠﻴﺎت اﻟﺤﺎﺳﻮﺑﻴﺔ ﺑﺴﺮﻋﺔ32 و64 ﺑﺖ ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔHyper Transport و3.0 PowerNow ﻡﻘﺒﺲAM2+ / AM3 ﻡﻌﺎﻟﺠﺎتAMD Athlon 64 / Athlon 64 FX / Sempron / Phenom / Phenom II / Althlon 64 X2 ( :ﻗﺼѧѧѧﻮى واط95)و وﺡﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰیﺔ ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔHyperTransport ﺑﺘﺮدد یﺼﻞ إﻟﻰ3.0 5.2 GT/s اﻟﻨﺎﻗﻞ اﻷﻡﺎﻡﻲ اﻟﺠﺎﻥﺒﻲ GeForce 8200 ﻡﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ ﺪﻋﻢﺗ ﺗﻘﻨﻴﺔ Low Pin Count Interface وﺳﺎﺋﻞ اﻟﺘﺤﻜﻢ ﻓﻲ اﻟﺒﻴﺌﺔ : ﻡﺮاﻗﺐ ﻟﻤﻌﺮﻓﺔ ﺡﺎﻟﺔ ا ﻷﺟﻬﺰة "وﻇﻴﻔﺔSmart Guardian" ﻡﻦITE ITE 8718 ﺗﻮﻓﺮ وﻇﻴﻔﺔSuper I/O ً اﻷآﺜﺮ اﺳﺘﺨﺪاﻡﺎ . Super I/O وﺡﺪة ذاآﺮةDDR2 ﻡﺰدوﺟﺔ اﻟﻘ ﻨﺎة ﺗﺪﻋﻢ اﻟﺬاآﺮة ﻡﻦ ﻥﻮعDDR2 ﺳﻌﺎت533 / 667 / 800 ﻡﻴﺠﺎ ﺑﺎیﺖ ﺗﺪﻋﻢ اﻟﺬاآﺮة ﻡﻦ ﻥﻮعDDR2 ﺳﻌﺎت1066 ﻡﻴﺠﺎ ﺑﺎیﺖ (DDR2 1066 is by AM2+ / AM3 CPU) ﻻ ﺗﺪﻋﻢ رﻗﺎﺋﻖ اﻟﺬاآﺮةDIMM وﺗﻠﻚ اﻟﺘﻲ ﻻ ﺗﺘﻮاﻓﻖ ﻡﻊECC ﻓﺘﺤﺔDDR2 DIMM ﻋﺪد2 ﺳﻌﺔ ذاآﺮة ﻗﺼﻮى8 ﺟﻴﺠﺎ ﺑﺎیﺖ ﺗﺪﻋﻢ آﻞ ﻓﺘﺤﺔ DIMM ﺗﺪﻋﻢ ذاآﺮة ﻡﻦ ﻥﻮعDDR2 ﺳﻌﺔ256/512 ﻡﻴﺠﺎ ﺑﺎیﺖ و1 / و2 / و4 ﺟﻴﺠﺎ ﺑﺎیﺖ اﻟﺬاآﺮة اﻟﺮﺋﻴﺴﻴﺔ أﻗﺼﻰ ﺳﻌﺔ ﻟﺬاآﺮة اﻟﻔﻴﺪیﻮ اﻟﻤﺸﺘﺮآﺔ 512 ﺑﺎیﺖ ﻡﻴﺠﺎ ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔDX10 / HDCP / PureVideo ﻡﺪﻡﺠﺔ ﻓﻲ رﻗﺎﺋﻖGeForce 8200 ﺑﻄﺎﻗﺔ اﻟﺮﺳﻮﻡﺎت ﻥﺎﻗﻞ ﺑﺘﻘﻨﻴﺔUltra DMA 33 / 66 / 100 / 133وﺿﻊ رﺋﻴﺴﻲ دﻋﻢ وﺿﻊPIO Mode 0~4 ﻡﺘﺤﻜﻢIDE ﻡﺘﻜﺎﻡﻞ ﻡﻨﻔﺬIDE ﻥﻘﻞ اﻟﺒﻴﺎﻥﺎت ﺑﺴﺮﻋﺎت ﺗﺼﻞ إﻟﻰ 3 ﺟﻴﺠﺎﺑﺖ ﺙﺎﻥﻴﺔ / . ﻡﻄﺎﺑﻘﺔ ﻟﻤﻮاﺹﻔﺎت SATA اﻹﺹﺪار 2.0. ﻡﺘﺤﻜﻢ Serial ATA ﻡﺘﻜﺎﻡﻞ SATA ﺗﻔﺎوض ﺗﻠﻘﺎﺋﻲ 10 / 100 ﺑﺎیﺖ ﻣﻴﺠﺎ / و ﺛﺎﻧﻴﺔ1ﺛﺎﻧﻴﺔ /ﺑﺖ ﺝﻴﺠﺎ إﻡﻜﺎﻥﻴﺔ اﻟﻨﻘﻞ اﻟﻤﺰدوج اﻟﻜﺎﻡﻞ / اﻟﻨﺼﻔﻲ Realtek RTL 8111DL ﺵﺒﻜﺔ داﺥﻠﻴﺔ 5.1 ﻗﻨﻮات ﻟﺨﺮج اﻟﺼﻮت ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ اﻟﺼﻮت ﻋﺎﻟﻲ اﻟﺘﻌﺮیﻒ ﻡﻦ ALC662 دﻋﻢ اﻟﺼﻮت ﻋﺎﻟﻲ اﻟﺘﻌﺮیﻒ ﻓﺘﺤﺔx16 PCI Express Gen2 ﻋﺪد1 ﻓﺘﺤﺔPCI ﻋﺪد2 اﻟﻔﺘﺤﺎت یﺪﻋﻢ ﻡﺤﺮآﻴﻦ ﻟﻸﻗﺮاص اﻟﻤﺮﻥﺔ ﻡﻨﻔﺬ ﻡﺤﺮك أﻗﺮاص ﻡﺮﻥﺔ ﻋﺪد 1 یﺪﻋﻢ آﻞ ﻡﻨﻔﺬ اﺙﻨﻴﻦ ﻡﻦ أﺟﻬﺰةIDE ﻡﻨﻔﺬIDE ﻋﺪد1 یﺪﻋﻢ آﻞ ﻡﻨﻔﺬ واﺡﺪ ﻡﻦ أﺟﻬﺰةSATA ﻡﻨﻔﺬSATA ﻋﺪد4 اﻟﻤﻨﺎﻓﺬ ﻋﻠﻰ ﺳﻄﺢ اﻟﻠﻮﺡﺔ

اﻟﻠﻮﺡﺔ اﻷﻡﺎﻡﻴﺔ ﻋﺪد 1 یﺪﻋﻢ وﻇﻴﻔﺔ اﻟﺼﻮت ﺑﺎﻟﻠﻮﺡﺔ اﻷﻡﺎﻡﻴﺔ ﻡﻨﻔﺬ اﻟﺼﻮت اﻷﻡﺎﻡﻲ ﻋﺪد 1 یﺪﻋﻢ وﻇﻴﻔﺔ دﺥﻞ ﺹﻮت اﻟﻘﺮص اﻟﻤﺪﻡﺞ ﻡﻨﻔﺬCD-IN ﻋﺪد1 ﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺡﺔ وﺡﺪة اﻟﻤﻌﺎﻟﺠﺔ ﻡﻊ وﻇﻴﻔﺔSmart Fan وﺹﻠﺔ ﻡﺮوﺡﺔ وﺡﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰیﺔ ﻋﺪد 1 ﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺡﺔ اﻟ ﻨﻈﺎم وﺹﻠﺔ ﻡﺮوﺡﺔ اﻟﻨﻈﺎم ﻋﺪد 1 وﺹﻠﺔ ﻡﺴﺢCMOS ﻋﺪد1 یﺪﻋﻢ آﻞ ﻡﻨﻔﺬ ﻓﺘﺤﺘﻲUSB ﺑﺎﻟﻠﻮﺡﺔ اﻷﻡﺎﻡﻴﺔ ﻡﻨﻔﺬUSB ﻋﺪد2 ﻡﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )24دﺑﻮس ( ﻋﺪد 1 ﻡﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )4دﺑﻮس ( ﻋﺪد 1 ﻡﻨﻔﺬ ﻃﺎﺑﻌﺔ ﻋﺪد 1 ﻡﻨﻔﺬ ﺗﺴﻠﺴﻠﻲ ﻋﺪد 1 ﻟﻮﺡﺔ ﻡﻔﺎﺗﻴﺢPS/2 ﻋﺪد1 ﻡﺎوس PS/2 ﻋﺪد1 ﻡﻨﻔﺬVGA ﻋﺪد1 ﻡﻨﻔﺬ ﺵﺒﻜﺔ اﺗﺼﺎل ﻡﺤﻠﻴﺔ ﻋﺪد 1 ﻡﻨﺎﻓﺬUSB ﻋﺪد4 ﻡﻘﺒﺲ ﺹﻮت ﻋﺪ3 ﻡﻨﺎﻓﺬDVI ﻋﺪد1 دﺥﻞ ﻡﻨﺎﻓﺬ ﺥﺮج / اﻟﻠﻮﺡﺔ اﻟﺨﻠﻔﻴﺔ 190 )ﻡﻢ ﻋﺮض ( X 244 )ﻡﻢ ارﺗﻔﺎع ( ﺡﺠﻢ اﻟﻠﻮﺡﺔ ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔRAID 0 / 1 / 5 / 0+1 ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔHybrid SLI (by nVIDIA driver) ﻡﺰایﺎ ﺥﺎﺹﺔ ﺗﺤﺘﻔﻆBiostar ﺑﺤﻘﻬﺎ ﻓﻲ إﺿﺎﻓﺔ أو إزاﻟﺔ اﻟﺪﻋﻢ ﻷي ﻥﻈﺎم ﺗﺸﻐﻴﻞ ﺑﺈﺥﻄﺎر أو ﺑﺪون إﺥﻄﺎر . Windows XP / Vista 32 / Vista 64 دﻋﻢ أﻥﻈﻤﺔ اﻟﺘﺸﻐﻴﻞ

AMD Athlon 64 / Athlon 64 FX / Althlon 64 X2 / Sempron / Phenom / Phenom II プロ セッサ (最高のワット: 95W) AMD 64アーキテクチャでは、32ビットと64ビット計算が可 能です ハイパートランスポート3.0とクールアンドクワイアットを サポートします FSB 5.2 GT/sのバンド幅までハイパートランスポ ート3.0をサポートします チップセッ ト GeForce 8200 メインメモ リ DDR2 DIMMスロット x 2 最大メモリ容量8GB 各DIMMは 256MB/512MB/1GB/2GB/4GB DDR2をサポート デュアル チャンネルモードDDR2メモリモジュール DDR2 533 / 667 / 800 をサポート DDR2 1066 をサポート (by AM2+ / AM3 CPU) 登録済みDIMMとECC DIMMはサポートされません Super I/O ITE 8718 もっとも一般に使用されるレガシーSuper I/O 機能を採用しています。 低ピンカウントインターフェイス 環境コントロールイニシアチブ、 H/Wモニター ITEの「スマートガーディアン」機能 グラフィッ クス GeForce 8200チップセットに統合 最大の共有ビデオメモリは512MBです DX10 / HDCP / PureVideo のサポート IDE 統合IDEコントローラ Ultra DMA 33 / 66 / 100 / 133バスマスタモード PIO Mode 0~4のサポート、 SATA 統合シリアルATAコントローラ 最高3Gb/秒のデータ転送速度 SATAバージョン2.0仕様に準拠。 LAN Realtek RTL 8111DL 10 / 100 / 1000 Mb/秒のオートネゴシエーション 半/全二重機能 HDオーディ オのサポー ト ALC662 5.1チャンネルオーディオアウト ハイデフィニションオーディオのサポート PCI Express Gen2 x16スロット x1 スロット PCIスロット x2 フロッピーコネクタ x1 各コネクタは2つのフロッピードライブをサポートします オンボード コネクタ IDEコネクタ x1 各コネクタは2つのIDEデバイスをサポートします

特殊機能 RAID 0 / 1 / 5 / 0+1 のサポート Hybrid SLI のサポート(by nVIDIA driver) OSサポート Windows XP / Vista 32 / Vista 64 Biostarは事前のサポートなしにOSサポートを追加または削 除する権利を留保します。 2009/03/13