Biostar TP67XE - BIOS Setup Manual

FCC Information and Copyright This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. The vendor makes no representations or warranties with respect to the contents here and specially disclaims any implied warranties of merchantability or fitness for any purpose. Further the vendor reserves the right to revise this publication and to make changes to the contents here without obligation to notify any party beforehand. Duplication of this publication, in part or in whole, is not allowed without first obtaining the vendor’s approval in writing. The content of this user’s manual is subject to be changed without notice and we will not be responsible for any mistakes found in this user’s manual. All the brand and product names are trademarks of their respective companies. Dichiarazione di conformità sintetica Ai sensi dell’art. 2 comma 3 del D.M. 275 del 30/10/2002 Si dichiara che questo prodotto è conforme alle normative vigenti e soddisfa i requisiti essenziali richiesti dalle direttive 2004/108/CE, 2006/95/CE e 1999/05/CE quando ad esso applicabili Short Declaration of conformity We declare this product is complying with the laws in force and meeting all the essential requirements as specified by the directives 2004/108/CE, 2006/95/CE and 1999/05/CE whenever these laws may be applied

Chapter 1: Introduction ........................................ 1 1.1 Before You Start......................................................................................... 1 1.2 Package Checklist ..................................................................................... 1 1.3 Motherboard Features.............................................................................. 2 1.4 Rear Panel Connectors.............................................................................. 3 1.5 Motherboard Layout................................................................................. 4 Chapter 2: Hardware Installation .......................... 5 2.1 Installing Central Processing Unit (CPU)............................................... 5 2.2 FAN Headers.............................................................................................. 7 2.3 Installing System Memory ........................................................................ 8 2.4 Connectors and Slots................................................................................ 10 Chapter 3: Headers & Jumpers Setup .................. 14 3.1 How to Setup Jumpers............................................................................. 14 3.2 Detail Settings.......................................................................................... 14 Chapter 4: RAID Functions .................................. 20 4.1 Operating System.................................................................................... 20 4.2 Raid Arrays............................................................................................... 20 4.3 How RAID Works..................................................................................... 20 Chapter 5: T-Series UEFI BIOS & Software........... 24 5.1 T-Series UEFI BIOS ................................................................................... 24 5.2 T-Series Software...................................................................................... 27 Chapter 6: Useful Help ........................................ 37 6.1 Driver Installation Note.......................................................................... 37 6.2 Extra Information.................................................................................... 38 6.3 AMI BIOS Post Code................................................................................. 39 6.4 Troubleshooting....................................................................................... 41 Appendix: SPEC In Other Languages ................... 42 German.................................................................................................................. 42 French .................................................................................................................... 44 Italian..................................................................................................................... 46 Spanish................................................................................................................... 48 Portuguese............................................................................................................ 50 Polish...................................................................................................................... 52 Russian................................................................................................................... 54 Arabic..................................................................................................................... 56 Japanese................................................................................................................ 58

1.1 BEFORE YOU START Thank you for choosing our product. Before you start installing the motherboard, please make sure you follow the instructions below: „ Prepare a dry and stable working environment with sufficient lighting. „ Always disconnect the computer from power outlet before operation. „ Before you take the motherboard out from anti-static bag, ground yourself properly by touching any safely grounded appliance, or use grounded wrist strap to remove the static charge. „ Avoid touching the components on motherboard or the rear side of the board unless necessary. Hold the board on the edge, do not try to bend or flex the board. „ Do not leave any unfastened small parts inside the case after installation. Loose parts will cause short circuits which may damage the equipment. „ Keep the computer from dangerous area, such as heat source, humid air and water. „ The operating temperatures of the computer should be 0 to 45 degrees Celsius. 1.2 PACKAGE CHECKLIST Serial ATA Cable X 3 Rear I/O Panel for ATX Case X 1 User’s Manual X 1 Fully Setup Driver CD X 1 USB 2.0 Cable X1 (optional) Serial ATA Power Cable X 1 (optional) CFX Bridge X 1 SLI Bridge X 1 Note: The package contents may be different due to area or your motherboard version.

processor Supports Execute Disable Bit / Enhanced Intel SpeedStep® / Intel Architecture-64 / Extended Memory 64 Technology / Virtualization Technology / Hyper Threading Chipset Intel P67 Super I/O IT8728 Provides the most commonly used legacy Super I/O functionality. Low Pin Count Interface Environment Control initiatives, Hardware Monitor Controller Fan Speed Controller ITE's "Smart Guardian" function Main Memory DDR3 DIMM Slots x 4 Max Memory Capacity 16GB Each DIMM supports 512MB/ 1GB/2GB/4GB DDR3 Dual Channel Mode DDR3 memory module Supports DDR3 1066 / 1333 Supports DDR3 1600 (OC) / 1866 (OC) / 2133 (OC) Registered DIMM and ECC DIMM is not supported SATA 2 & 3 Integrated Serial ATA Controller Data transfer rates up to 3.0 Gb/s / 6.0 Gb/s. SATA Version 2.0 / 3.0 specification compliant LAN Realtek RTL 8111E 10 / 100 Mb/s / 1Gb/s auto negotiation Half / Full duplex capability Sound Codec ALC892 7.1 channels audio out High Definition Audio USB3.0 NEC uPD720200 Data transfer rates up to 600 MB/s IEEE 1394 VT6315N 1394a PCI slot x2 Supports PCI expansion cards PCI Express Gen2 x 16 slot x2 Supports PCI-E Gen2 x16 expansion cards Slots PCI Express Gen2 x 1 slot x2 Supports PCI-E Gen2 x1 expansion cards SATA3 Connector x2 Each connector supports 1 SATA3 devices SATA2 Connector x3 Each connector supports 1 SATA2 devices Front Panel Connector x1 Supports front panel facilities Front Audio Connector x1 Supports front panel audio function CPU Fan Header x1 CPU Fan power supply (with Smart Fan function) System Fan Header x2 System Fan Power supply Clear CMOS Header x1 Restore CMOS data to factory default On Board Connectors USB2.0 Connector x3 Each connector supports 2 front panel USB2.0 ports

x1 Supports infrared function Serial Port Connector x1 Connects to RS-232 Port IEEE 1394 Connector x1 Connects to IEEE 1394 device S/PDIF out Connector x1 Supports digital audio out function Power Connector (24pin) x1 Connects to Power supply Power Connector (8pin) x2 Connects to Power supply Back Panel I/O PS/2 Keyboard x1 RCA + S/PDIF Out x1 1394 Port x1 eSATA Port x1 LAN port x1 USB2.0 Port x6 USB3.0 Port x2 Audio Jack x6 Connects to PS/2 Keyboard Provides digital audio out function Connects to IEEE 1394 device Connect to SATA devices Connect to RJ-45 ethernet cable Connect to USB2.0 devices Connect to USB3.0 devices (by NEC uPD720200) and USB2.0/USB1.X devices (by P67) Provide Audio-In/Out and Mic. connection Board Size 305 (W) x 244 (L) mm ATX OS Support Windows XP / Vista / 7 Biostar reserves the right to add or remove support for any OS with or without notice 1.4 REAR PANEL CONNECTORS Line In Line Out Mic In Center Rear Side eSATA USB3.0X2 LAN USB2.0X2 IEEE 1394 USB2.0X2 RCA + S/PDIF Out PS/2 Keyboard USB2.0X2 NOTE: USB3.0 ports are backward compatible with USB2.0/USB1.X devices. USB3.0 is controlled by NEC uPD720200, but, USB2.0/USB1.X is controlled by P67.

■ st pin.

2.1 INSTALLING CENTRAL PROCESSING UNIT (CPU) Special Notice: Remove Pin Cap before installation, and make good preservation for future use. When the CPU is removed, cover the Pin Cap on the empty socket to ensure pin legs won’t be damaged. Step 1: Pull the socket locking lever out from the socket and then raise the lever up. Step 2: Remove the Pin Cap.

CPU should point forwards this triangular cut edge. The CPU will fit only in the correct orientation. Step 4: Hold the CPU down firmly, and then lower the lever to locked position to complete the installation. Step 5: Put the CPU Fan and heatsink assembly on the CPU and buckle it on the retention frame. Connect the CPU FAN power cable into the CPU_FAN1 to complete the installation.

cable and connector may be different according to the fan manufacturer. Connect the fan cable to the connector while matching the black wire to pin#1. CPU_FAN1: CPU Fan Header Pin Assignment 1 Ground 2 +12V 3 FAN RPM rate sense 4 1 4 Smart Fan Control SYS_FAN1/SYS_FAN2: System Fan Headers Pin Assignment 1 Ground 2 +12V 1 3 SYS_FAN2 SYS_FAN1 3 1 3 FAN RPM rate sense Note: The SYS_FAN1/SYS_FAN2 support 3-pin head connectors; the CPU_FAN1 supports 4-pin head connector. When connecting with wires onto connectors, please note that the red wire is the positive and should be connected to pin#2, and the black wire is Ground and should be connected to GND.

A. Memory Modules DDR3_A1 DDR3_B1 DDR3_A2 DDR3_B2 1. Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot such that the notch on the DIMM matches the break on the Slot. 2. Insert the DIMM vertically and firmly into the slot until the retaining chip snap back in place and the DIMM is properly seated.

DIMM Socket Location DDR3 Module Total Memory Size DDR3_A1 512MB/1GB/2GB/4GB DDR3_A2 512MB/1GB/2GB/4GB DDR3_B1 512MB/1GB/2GB/4GB DDR3_B2 512MB/1GB/2GB/4GB Max is 16GB. C. Dual Channel Memory Installation Please refer to the following requirements to activate Dual Channel function: Install memory module of the same density in pairs, shown in the table. Dual Channel Status DDR3_A1 DDR3_A2 DDR3_B1 DDR3_B2 Enabled X O X O Enabled O O O O (O means memory installed, X means memory not installed.) The DRAM bus width of the memory module must be the same (x8 or x16) Note: Memory module must be installed in DDR3-A2 or DDR3-B2 to boot the system.

SATA1: Serial ATA3 Connectors The motherboard has a PCI to SATA Controller with 2 channels SATA3 interface, it satisfies the SATA 3.0 spec and with transfer rate of 6.0Gb/s. Pin Assignment 1 Ground 2 TX+ 3 TX- 4 Ground 5 RX- 6 RX+ 7 Ground SATA2/3: Serial ATA2 Connectors The motherboard has a PCI to SATA Controller with 3 channels SATA2 interface, it satisfies the SATA 2.0 spec and with transfer rate of 3.0Gb/s. Pin Assignment 1 Ground 2 TX+ 3 TX- 4 Ground 5 RX- 6 RX+ 1 4 7 SATA3 SATA2 7 Ground

- PCI-Express 2.0 compliant. - Maximum theoretical realized bandwidth of 8GB/s simultaneously per direction, for an aggregate of 16GB/s totally. - PCI-Express Gen2 supports a raw bit-rate of 5.0Gb/s on the data pins. - 2X bandwidth over the PCI-Express 1.1 architecture. PEX16_2: PCI-Express Gen2 x8 Slot - PCI-Express 2.0 compliant. - Maximum theoretical realized bandwidth of 4GB/s simultaneously per direction, for an aggregate of 8GB/s totally. PEX1_1/PEX1_2: PCI-Express Gen2 x1 Slot - PCI-Express 2.0 compliant. - Data transfer bandwidth up to 500MB/s per direction; 1GB/s in total. - PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins. - 2X bandwidth over the traditional PCI architecture. PEX16_1 PEX1_1 PEX16_2 PEX1_2

This motherboard is equipped with 2 standard PCI slots. PCI stands for Peripheral Component Interconnect, and it is a bus standard for expansion cards. This PCI slot is designated as 32 bits. PCI2 PCI1 ATXPWR2/3: ATX Power Source Connectors These connectors provide +12V to CPU power circuit. If the CPU power plug is 4-pin, please plug it into Pin 1-2-5-6 of ATXPWR2/3. Pin Assignment 1 +12V 2 +12V 3 Ground 1 4 5 8 1 4 5 8 ATXPWR2 ATXPWR3 4 Ground Note: Generally, any of ATXPWR2 and ATXPWR3 can be plugged. When system is overclocked, it is recommended to plug in both ATXPWR2 and ATXPWR3 for stability.

This connector allows user to connect 24-pin power connector on the ATX power supply. 1 12 13 24 Pin Assignment Pin Assignment 13 +3.3V 1 +3.3V 14 -12V 2 +3.3V 15 Ground 3 Ground 16 PS_ON 4 +5V 17 Ground 5 Ground 18 Ground 6 +5V 19 Ground 7 Ground 20 NC 8 PW_OK 21 +5V 9 Standby Voltage+5V 22 +5V 10 +12V 23 +5V 11 +12V 24 Ground 12 +3.3V Note: Before you power on the system, please make sure that ATXPWR1 ~ ATXPWR3 connectors have been well plugged-in.

3.1 HOW TO SETUP JUMPERS The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”, if not, that means the jumper is “open”. Pin opened Pin closed Pin1-2 closed 3.2 DETAIL SETTINGS PANEL1: Front Panel Header This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and speaker connection. It allows user to connect the PC case’s front panel switch functions. 1 9 8 16 POW_LED On/Off RST HLED SPK + + + - - Pin Assignment Function Pin Assignment Function 1 +5V 9 N/A 2 N/A 10 N/A N/A 3 N/A 11 N/A N/A 4 Speaker Speaker Connector 12 Power LED (+) 5 HDD LED (+) 13 Power LED (+) 6 HDD LED (-) Hard drive LED 14 Power LED (-) Power LED 7 Ground 15 Power button 8 Reset control Reset button 16 Ground Power-on button

These headers allow user to connect additional USB cable on the PC front panel, and also can be connected with internal USB devices, like USB card reader. Pin Assignment 1 +5V (fused) 2 +5V (fused) 3 USB- 4 USB- 5 USB+ 6 USB+ 7 Ground 8 Ground 9 Key 1 2 9 10 F_ USB1 F_USB2 USB3 F_ 10 NC F_1394A1: IEEE 1394 Header This header allows user to connect IEEE 1394 device. Pin Assignment 1 TPA1+ 2 TPA1- 3 GND 4 GND 5 TPB1+ 6 TPB1- 7 VCC 8 VCC 9 N/A 1 2 9 10 10 KEY

This header allows user to connect the front audio output cable with the PC front panel. This header allows only HD audio front panel connector; AC’97 connector is not acceptable. Pin Assignment 1 Mic Left in 2 Ground 3 Mic Right in 4 GPIO 5 Right line in 6 Jack Sense 7 Front Sense 8 Key 9 Left line in 1 2 9 10 10 Jack Sense JSPDIFOUT1: Digital Audio-out Connector This connector allows user to connect the PCI bracket SPDIF output header. Pin Assignment 1 +5V 2 SPDIF_OUT 3 1 3 Ground

Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and the CMOS data. Please carefully follow the procedures to avoid damaging the motherboard. 1 3 Pin 1-2 Close: Normal Operation (default). 1 3 1 3 Pin 2-3 Close: Clear CMOS data. ※ Clear CMOS Procedures: 1. Remove AC power line. 2. Set the jumper to “Pin 2-3 close”. 3. Wait for five seconds. 4. Set the jumper to “Pin 1-2 close”. 5. Power on the AC. 6. Reset your desired password or clear the CMOS data. J_COM1: Serial Port Connector The motherboard has a Serial Port Connector for connecting RS-232 Port. Pin Assignment 1 Carrier detect 2 Received data 3 Transmitted data 4 Data terminal ready 5 Signal ground 6 Data set ready 7 Request to send 8 Clear to send 9 Ring indicator 1 9 2 10 10 NC

There are 12 LED indicators on the motherboard showing system status. PH5 PH6 PH3 PH4 PH1 PH2 PH7 PH8 VTT_LED1 VTT_LED2 PH1 ~ PH8 / VTT_LED1 ~ VTT_LED2: Power Status Indicators Please refer to the tables below for specific messages: PH1~PH8 VTT_LED1~VTT_LED2 Phase Indicator ON Phase Active OFF Phase Inactive On-Board Buttons There are 2 on-board buttons. SW_RST1 SW_PWR1 SW_RST1: Reset button. SW_PWR1: Power Switch button.

This indicator will show POST code while booting. After the booting sequence, it will show current CPU temperature through hexadecimal figure. Please refer to Chapter 6.3 for all the BIOS POST codes. CIR1: Consumer IR Connector This header is for infrared remote control and communication. Pin Assignment 1 IrDA serial input 2 Ground 3 Ground 4 Key 5 IrDA serial output 6 IR Power 1 2 5 6

4.1 OPERATING SYSTEM Supports Windows Vista and Windows 7. 4.2 RAID ARRAYS RAID supports the following types of RAID arrays: RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for many applications. RAID 1: RAID 1 defines techniques for mirroring data. RAID 10: RAID 10 combines the techniques used in RAID 0 and RAID 1. RAID 5: RAID 5 provides fault tolerance and better utilization of disk capacity. 4.3 HOW RAID WORKS RAID 0: The controller “stripes” data across multiple drives in a RAID 0 array system. It breaks up a large file into smaller blocks and performs disk reads and writes across multiple drives in parallel. The size of each block is determined by the stripe size parameter, which you set during the creation of the RAID set based on the system environment. This technique reduces overall disk access time and offers high bandwidth. Features and Benefits ­ Drives: Minimum 2, and maximum is up to 6 or 8. Depending on the platform. ­ Uses: Intended for non-critical data requiring high data throughput, or any environment that does not require fault tolerance. ­ Benefits: provides increased data throughput, especially for large files. No capacity loss penalty for parity. ­ Drawbacks: Does not deliver any fault tolerance. If any drive in the array fails, all data is lost. ­ Fault Tolerance: No. Block 1 Block 3 Block 5 Block 2 Block 4 Block 6

array system. The mirrored (backup) copy of the data can reside on the same disk or on a second redundant drive in the array. RAID 1 provides a hot-standby copy of data if the active volume or drive is corrupted or becomes unavailable because of a hardware failure. RAID techniques can be applied for high-availability solutions, or as a form of automatic backup that eliminates tedious manual backups to more expensive and less reliable media. Features and Benefits ­ Drives: Minimum 2, and maximum is 2. ­ Uses: RAID 1 is ideal for small databases or any other application that requires fault tolerance and minimal capacity. ­ Benefits: Provides 100% data redundancy. Should one drive fail, the controller switches to the other drive. ­ Drawbacks: Requires 2 drives for the storage space of one drive. Performance is impaired during drive rebuilds. ­ Fault Tolerance: Yes. Block 1 Block 2 Block 3 Block 1 Block 2 Block 3

solution for improved resiliency, performance and rebuild performance. Features and Benefits ­ Drives: Minimum 4, and maximum is 6 or 8, depending on the platform. ­ Benefits: Optimizes for both fault tolerance and performance, allowing for automatic redundancy. May be simultaneously used with other RAID levels in an array, and allows for spare disks. ­ Drawbacks: Requires twice the available disk space for data redundancy, the same as RAID level 1. ­ Fault Tolerance: Yes. Block 1 Block 3 Block 5 Block 2 Block 4 Block 6 Block 1 Block 3 Block 5 Block 2 Block 4 Block 6

data and parity blocks across all the drives in the array. Fault tolerance is maintained by ensuring that the parity information for any given block of data is placed on a different drive from those used to store the data itself. Features and Benefits ­ Drives: Minimum 3. ­ Uses: RAID 5 is recommended for transaction processing and general purpose service. ­ Benefits: An ideal combination of good performance, good fault tolerance, and high capacity and storage efficiency. ­ Drawbacks: Individual block data transfer rate same as a single disk. Write performance can be CPU intensive. ­ Fault Tolerance: Yes. Disk 1 DATA 3 PARITY DATA 7 DATA 1 DATA 9 PARITY Disk 2 PARITY DATA 5 DATA 8 DATA 2 PARITY DATA 11 Disk 3 DATA 4 DATA 6 PARITY PARITY DATA 10 DATA 12

5.1 T-SERIES UEFI BIOS T-Series UEFI BIOS Features Overclocking Navigator Engine (O.N.E.) Self Recovery System (S.R.S) Smart Fan Function BIO-Flasher: Update UEFI BIOS file from USB Flash Drive A. Overclocking Navigator Engine (O.N.E.) O.N.E provides 4 systems allowing users to customize personal overclock settings: Manual CPU System, Manual Memory System, Manual PWM System, and Manual Voltage System. BIOS SETUP UTILITY Notice: Please Clear CMOS if system no display after overclocking ====Manual CPU system==== CPU Ratio 28 Start Page [Page - Main] Fixed CPU Ratio [Disabled] CPU Base Clock(1/100 MHZ) 10000 CPU Core Current Max(Amp) 150 Power Limit 1 Value (Watt) 95 Power Limit 2 Switch [Enabled] Power Limit 2 Value 118 Enhanced Intel SpeedStep Tech [Enabled] Turbo Mode [Enabled] 1 Core Ratio Limit 31 2 Core Ratio Limit 30 3 Core Ratio Limit 30 4 Core Ratio Limit 29 CPU C1E [Enabled] Version x.xx.xxxx. Copyright© 201x, American Megatrends, Inc. Start Page help Main Advanced Chipset Boot Security O.N.E Save & Exit Select Screen Select Item Select Change Opt. General Help Optimized Defaults Save & Reset Exit Enter +/- F1 F3 F4 ESC Notice: Not all types of Intel CPU perform above overclock setting ideally; the difference will be based on the selected CPU model. !! WARNING !! For better system performance, the UEFI BIOS firmware is being continuously updated. The UEFI BIOS information described below in this manual is for your reference only and the actual UEFI BIOS information and settings on board may be different from this manual. For further information of setting up the UEFI BIOS, please refer to the UEFI BIOS Manual in the Setup CD.

This function can’t be seen under UEFI BIOS setup, and is always on whenever the system starts up. However, it can prevent system hang-up due to inappropriate overclock actions. When the system hangs up, S.R.S. will automatically log in the default UEFI BIOS setting, and all overclock settings will be re-configured. C. Smart Fan Function Smart Fan Function is under “Smart Fan Control” in “Advanced Menu”. This is a brilliant feature to control CPU/System Temperature vs. Fan speed. When enabling Smart Fan function, Fan speed is controlled automatically by CPU/System temperature. This function will protect CPU/System from overheat problem and maintain the system temperature at a safe level. BIOS SETUP UTILITY > PCI Subsystem Settings > ACPI Settings/WakeUp Event control > CPU Configuration > SATA Configuration > USB Configuration > Super IO Configuration > H/W Monitor > SMART FAN Control Version x.xx.xxxx. Copyright© 201x, American Megatrends, Inc. SMART FAN Control Main Advanced Chipset Boot Security O.N.E Save & Exit Select Screen Select Item Select Change Opt. General Help Optimized Defaults Save & Reset Exit Enter +/- F1 F3 F4 ESC ↓ NOTE Overclock is an optional process, but not a “must-do” process; it is not recommended for inexperienced users. Therefore, we will not be responsible for any hardware damage which may be caused by overclocking. We also would not guarantee any overclocking performance.

SMART FAN Control > CPU FAN Calibrate CPU Smart FAN [Disabled] Control Mode [Manual] FAN Ctrl OFF( C) FAN Ctrl ON( C) FAN Ctrl Start value FAN Ctrl Sensitive o o Version x.xx.xxxx. Copyright© 201x, American Megatrends, Inc. Advanced CPU FAN Smart control function. [Disabled]: Full ON [Auto]:By parameters below. Select Screen Select Item Select Change Opt. General Help Optimized Defaults Save & Reset Exit Enter +/- F1 F3 F4 ESC CPU Smart FAN This item allows you to control the CPU Smart Fan function. CPU FAN Calibrate Press [ENTER] to calibrate CPU FAN. Control Mode This item provides several operation modes of the fan. Fan Ctrl OFF(℃) When CPU temperature is lower than this value, the CPU fan will keep lowest RPM. The range is from 0~127, with an interval of 1. Fan Ctrl On(℃) When CPU temperature is higher than this value, the CPU fan controller will turn on. The range is from 0~127, with an interval of 1. Fan Ctrl Start Value This item sets CPU FAN Start Speed Value. The range is from 0~127, with an interval of 1. Fan Ctrl Sensitive The bigger the numeral is, the higher the FAN speed is. The range is from 0~127, with an interval of 1.

1. Insert the Setup CD to the optical drive. The driver installation program would appear if the Auto-run function has been enabled. 2. Select Software Installation, and then click on the respective software title. 3. Follow the on-screen instructions to complete the installation. Launching T-Series Software After the installation process is completed, you will see the software icon showing on the desktop. Double-click the icon to launch it. TOverclocker TOverclocker presents a simple Windows-based system performance enhancement and manageability utility. It features several powerful and easy to use tools such as Overclocking for enhancing system performance, also for special enhancement on CPU and Memory. Smart-Fan management and PC health are for monitoring system status. This utility also allows you to make overclocking profiles saving unlimitedly, and pre-set OC modes are for easy OC. (The illustration below is for reference only)

The Memory tab provides information on the memory module(s). You can select memory module on a specific slot to see its information. The OC Tweaker tab allows you to change system clock settings and voltages settings. It also provides six pre-set modes for you:

The HW Monitor tab allows you to monitor hardware voltage, fan speed, and temperature. Besides, you also can set related values for CPU Smart Fan.

displays information about manufacturer and software version. You can update current version by clicking the button “Live Update.” Green Power II Utility BIOSTAR G.P.U II (Green Power Utility) is a new function. The utility enhances energy efficiency by disabling extra phases while CPU is on light loading; it features 4+1 power phases, current power saving, and toal power saving. This tool integrates a friendly GUI to monitor your CPU Usage, CPU Watt, and CPU Temperature. Moreover, it optimizes power saving and best power efficiency on your system. (The illustration below is for reference only) Display manufacturer & software version information Display CPU information Reset Time & Consumption Auto Phase Mode Maxi-Energy Mode Typical Mode Medium Mode Performance Mode

This utility provides five modes, upon your requirements, to improve system performance or to save power consumption. Note: Even if the modes saving more power consumption are chosen, the system still can keep excellent performance. „ Auto Phase Mode System switches the mode automatically according to current system loading condition. „ Performance Mode This is the mode saving power consumption most. Least energy will be used in the system. „ Typical Mode Compared with that in Performance Mode, energy consumption in this mode is a little bit more. „ Medium Mode This is the standard system power saving mode. „ Maxi-Energy Mode This is the best system performance mode.

Tech-Support system. This utility will collect the system information which is useful for analyzing the problem you may have encountered, and then send these information to our tech-support department to help you fix the problem. Before you use this utility, please set Outlook Express as your default e-mail client application program. This block will show the information which would be collected in the mail. Provide the e-mail address that you would like to send the copy to. Provide the name of the power supply manufacturer and the model no. Send the mail out. Save these information to a .txt file Exit this dialog. Select your area or the area close to you. * Provide the name of the memory module manufacturer. * Describe condition of your system. * * represents important information that you must provide. Without this information, you may not be able to send out the mail. After filling up this information, click “Send” to send the mail out. A warning dialog would appear asking for your confirmation; click “Send” to confirm or “Do Not Send” to cancel. If you want to save this information to a .txt file, click “Save As…” and then you will see a saving dialog appears asking you to enter file name.

“Save”. Your system information will be saved to a .txt file. Open the saved .txt file, you will see your system information including motherboard/BIOS/CPU/video/ device/OS information. This information is also concluded in the sent mail. We will not share customer’s data with any other third parties, so please feel free to provide your system information while using eHot-Line service. If you are not using Outlook Express as your default e-mail client application, you may need to save the system information to a .txt file and send the file to our tech support with other e-mail application.

motherboard BIOS under Windows system. Update BIOS with a BIOS file Clear CMOS function (Only for AWARD BIOS) Show current BIOS information Save current BIOS to a .bin file AWARD BIOS AMI BIOS Once click on this button, the saving dialog will show. Choose the position to save file and enter file name. (We recommend that the file name should be English/number and no longer than 7 characters.) Then click Save.

For AWARD BIOS, update BIOS procedure should be run with Clear CMOS function, so please check on Clear CMOS first. Then click Update BIOS button, a dialog will show for asking you backup current BIOS. Click Yes for BIOS backup and refer to the Backup BIOS procedure; or click No to skip this procedure. After the BIOS Backup procedure, the open dialog will show for requesting the BIOS file which is going to be updated. Please choose the proper BIOS file for updating, then click on Open. The utility will update BIOS with the proper BIOS file, and this process may take minutes. Please do not open any other applications during this process. After the BIOS Update process, click on OK to restart the system. While the system boots up and the full screen logo shows, press key to enter BIOS setup. In the BIOS setup, use the Load Optimized Defaults function and then Save and Exit Setup to exit BIOS setup. BIOS Update is completed. All the information and content above about the T-Series software are subject to be changed without notice. For better performance, the software is being continuously updated. The information and pictures described above are for your reference only. The actual information and settings on board may be slightly different from this manual.

This utility allows you to personalize your boot logo easily. You can choose JPG or BMP as your boot logo so as to customize your computer. Please follow the following instructions to update boo logo: 1. Load Image：Choose the picture as the boot logo. 2. Transform：Transform the picture for BIOS and preview the result. 3. Update Bios：Write the picture to BIOS Memory to complete the update.

6.1 DRIVER INSTALLATION NOTE After you installed your operating system, please insert the Fully Setup Driver CD into your optical drive and install the driver for better system performance. You will see the following window after you insert the CD The setup guide will auto detect your motherboard and operating system. Note: If this window didn’t show up after you insert the Driver CD, please use file browser to locate and execute the file SETUP.EXE under your optical drive. A. Driver Installation To install the driver, please click on the Driver icon. The setup guide will list the compatible driver for your motherboard and operating system. Click on each device driver to launch the installation program. B. Software Installation To install the software, please click on the Software icon. The setup guide will list the software available for your system, click on each software title to launch the installation program. C. Manual Aside from the paperback manual, we also provide manual in the Driver CD. Click on the Manual icon to browse for available manual. Note: You will need Acrobat Reader to open the manual file. Please download the latest version of Acrobat Reader software from http://www.adobe.com/products/acrobat/readstep2.html

seconds, that means the CPU protection function has been activated. When the CPU is over heated, the motherboard will shutdown automatically to avoid a damage of the CPU, and the system may not power on again. In this case, please double check: 1. The CPU cooler surface is placed evenly with the CPU surface. 2. CPU fan is rotated normally. 3. CPU fan speed is fulfilling with the CPU speed. After confirmed, please follow steps below to relief the CPU protection function. 1. Remove the power cord from power supply for seconds. 2. Wait for seconds. 3. Plug in the power cord and boot up the system. Or you can: 1. Clear the CMOS data. (See “Close CMOS Header: JCMOS1” section) 2. Wait for seconds. 3. Power on the system again.

Checkpoint Description 03 Disable NMI, Parity, video for EGA, and DMA controllers. Initialize BIOS, POST, Runtime data area. Also initialize BIOS modules on POST entry and GPNV area. Initialized CMOS as mentioned in the Kernel Variable "wCMOSFlags." 04 Check CMOS diagnostic byte to determine if battery power is OK and CMOS checksum is OK. Verify CMOS checksum manually by reading storage area. If the CMOS checksum is bad, update CMOS with power-on default values and clear passwords. Initialize status register A. Initializes data variables that are based on CMOS setup questions. Initializes both the 8259 compatible PICs in the system 05 Initializes the interrupt controlling hardware (generally PIC) and interrupt vector table. 06 Do R/W test to CH-2 count reg. Initialize CH-0 as system timer. Install the POSTINT1Ch handler. Enable IRQ-0 in PIC for system timer interrupt. Traps INT1Ch vector to "POSTINT1ChHandlerBlock." 07 Fixes CPU POST interface calling pointer. 08 Initializes the CPU. The BAT test is being done on KBC. Program the keyboard controller command byte is being done after Auto detection of KB/MS using AMI KB-5. C0 Early CPU Init Start -- Disable Cache – Init Local APIC. C1 Set up boot strap processor Information. C2 Set up boot strap processor for POST. C5 Enumerate and set up application processors. C6 Re-enable cache for boot strap processor. C7 Early CPU Init Exit. 0A Initializes the 8042 compatible Key Board Controller. 0B Detects the presence of PS/2 mouse. 0C Detects the presence of Keyboard in KBC port. 0E Testing and initialization of different Input Devices. Also, update the Kernel Variables. Traps the INT09h vector, so that the POST INT09h handler gets control for IRQ1. Uncompress all available language, BIOS logo, and Silent logo modules. 13 Early POST initialization of chipset registers. 20 Relocate System Management Interrupt vector for all CPU in the system. 24 Uncompress and initialize any platform specific BIOS modules. GPNV is initialized at this checkpoint. 2A Initializes different devices through DIM. See DIM Code Checkpoints section of document for more information. 2C Initializes different devices. Detects and initializes the video adapter installed in the system that have optional ROMs. 2E Initializes all the output devices. 31 Allocate memory for ADM module and uncompress it. Give control to ADM module for initialization. Initialize language and font modules for ADM. Activate ADM module. 33 Initializes the silent boot module. Set the window for displaying text information.

OEM specific information. 38 Initializes different devices through DIM. See DIM Code Checkpoints section of document for more information. USB controllers are initialized at this point. 39 Initializes DMAC-1 & DMAC-2. 3A Initialize RTC date/time. 3B Test for total memory installed in the system. Also, Check for DEL or ESC keys to limit memory test. Display total memory in the system. 3C Mid POST initialization of chipset registers. 40 Detect different devices (Parallel ports, serial ports, and coprocessor in CPU, etc.) successfully installed in the system and update the BDA, EBDA…etc. 52 Updates CMOS memory size from memory found in memory test. Allocates memory for Extended BIOS Data Area from base memory. Programming the memory hole or any kind of implementation that needs an adjustment in system RAM size if needed. 60 Initializes NUM-LOCK status and programs the KBD typematic rate. 75 Initialize Int-13 and prepare for IPL detection. 78 Initializes IPL devices controlled by BIOS and option ROMs. 7C Generate and write contents of ESCD in NVRam. 84 Log errors encountered during POST. 85 Display errors to the user and gets the user response for error. 87 Execute BIOS setup if needed / requested. Check boot password if installed. 8C Late POST initialization of chipset registers. 8D Build ACPI tables (if ACPI is supported). 8E Program the peripheral parameters. Enable/Disable NMI as selected. 90 Initialization of system management interrupt by invoking all handlers. Please note this checkpoint comes right after checkpoint 20h. A1 Clean-up work needed before booting to OS. A2 Takes care of runtime image preparation for different BIOS modules. Fill the free area in F000h segment with 0FFh. Initializes the Microsoft IRQ Routing Table. Prepares the runtime language module. Disables the system configuration display if needed. A4 Initialize runtime language module. Display boot option popup menu. A7 Displays the system configuration screen if enabled. Initialize the CPU’s before boot, which includes the programming of the MTRR’s. A9 Wait for user input at config display if needed. AA Uninstall POST INT1Ch vector and INT09h vector. AB Prepare BBS for Int 19 boot. Init MP tables. AC End of POST initialization of chipset registers. De-initializes the ADM module. B1 Save system context for ACPI. Prepare CPU for OS boot including final MTRR values. 00 Passes control to OS Loader (typically INT19h).

Power LED does not shine; the fan of the power supply does not work 2. Indicator light on keyboard does not shine. 1. Make sure power cable is securely plugged in. 2. Replace cable. 3. Contact technical support. System is inoperative. Keyboard lights are on, power indicator lights are lit, and hard drives are running. Using even pressure on both ends of the DIMM, press down firmly until the module snaps into place. System does not boot from a hard disk drive, but can be booted from optical drive. 1. Check cable running from disk to disk controller board. Make sure both ends are securely plugged in; check the drive type in the standard CMOS setup. 2. Backing up the hard drive is extremely important. All hard disks are capable of breaking down at any time. System only boots from an optical drive. Hard disks can be read, applications can be used, but system fails to boot from a hard disk. 1. Back up data and applications files. 2. Reformat the hard drive. Re-install applications and data using backup disks. Screen message shows “Invalid Configuration” or “CMOS Failure.” Review system’s equipment. Make sure correct information is in setup. System cannot boot after user installs a second hard drive. 1. Set master/slave jumpers correctly. 2. Run SETUP program and select correct drive types. Call the drive manufacturers for compatibility with other drives.

GERMAN Spezifikationen CPU Socket 1155 Intel Core i7 / i5 / i3 / Pentium / Celeron Prozessoren Unterstützt Execute Disable Bit / Enhanced Intel SpeedStep® / Intel Architecture-64 / Extended Memory 64 Technology / Virtualization Technology / Hyper Threading Chipsatz Intel P67 Super E/A IT8728 Bietet die häufig verwendeten alten Super E/A-Funktionen. Low Pin Count-Schnittstelle Umgebungskontrolle, Hardware-Überwachung Lüfterdrehzahl-Controller/-Überwachung "Smart Guardian"-Funktion von ITE Arbeitsspeich er DDR3 DIMM-Steckplätze x 4 Max. 16GB Arbeitsspeicher Jeder DIMM unterstützt 512MB/ 1GB/2GB/4GB DDR3. Dual-Kanal DDR3 Speichermodul Unterstützt DDR3 1066 / 1333 Unterstützt DDR3 1600(OC) / 1866(OC) / 2133(OC) registrierte DIMMs. ECC DIMMs werden nicht unterstützt. SATA 2 & 3 Integrierter Serial ATA-Controller Datentransferrate bis zu 3.0Gb/s / 6.0Gb/s. Konform mit der SATA-Spezifikation Version 2.0 / 3.0 LAN Realtek RTL 8111E 10 / 100 / 1000 Mb/s Auto-Negotiation Halb-/ Vollduplex-Funktion HD Audio-Unters tützung ALC892 Unterstützt High-Definition Audio 7.1-Kanal-Audioausgabe USB3.0 NEC uPD720200 Datenübertragungsraten bis zu 600 MB / s IEEE 1394 VT6315N 1394a PCI-Steckplatz x2 PCI Express Gen2 x16 Steckplatz x2 Steckplätze PCI Express Gen2 x 1-Steckplatz x2

SATA2-Anschluss x3 Jeder Anschluss unterstützt 1 SATA2-Laufwerk Fronttafelanschluss x1 Unterstützt die Fronttafelfunktionen Front-Audioanschluss x1 Unterstützt die Fronttafel-Audioanschlussfunktion CPU-Lüfter-Sockel x1 CPU-Lüfterstromversorgungsanschluss (mit Smart Fan-Funktion) System-Lüfter-Sockel x2 System-Lüfter-Stromversorgungsanschluss "CMOS löschen"-Sockel x1 USB2.0-Anschluss x3 Jeder Anschluss unterstützt 2 Fronttafel-USB2.0-Anschlüsse Verbraucher-IR Anschluss x1 Serieller Anschluss x1 IEEE 1394-Anschluss x1 S/PDIF Ausgangsanschluss x1 Unterstützt die digitale Audioausgabefunktion Stromanschluss (24-polig) x1 Onboard-Ans chluss Stromanschluss (8-polig) x2 Rückseiten-E /A PS/2-Tastatur x1 RCA + S/PDIF Heraus x1 1394-Anschluss x1 eSATA Anschluss x1 LAN-Anschluss x1 USB2.0-Anschluss x6 USB3.0-Anschluss x2 Audioanschluss x6 USB3.0 Geräte (durch NEC uPD720200) USB2.0/USB1.X Geräte (durch P67) Platinengröße 305 mm (B) X 244 mm (L) ATX OS-Unterstüt zung Windows XP / Vista / 7 Biostar behält sich das Recht vor, ohne Ankündigung die Unterstützung für ein Betriebssystem hinzuzufügen oder zu entfernen.

Celeron Prend en charge les technologies d'exécution de bit de désactivation / Intel SpeedStep® optimisée/ d'architecture Intel 64 / de mémoire étendue 64 / de virtualisation / Hyper Threading Chipset Intel P67 Super E/S IT8728 Fournit la fonctionnalité de Super E/S patrimoniales la plus utilisée. Interface à faible compte de broches Initiatives de contrôle environnementales, Moniteur de matériel Contrôleur /moniteur de vitesse de ventilateur Fonction "Gardien intelligent" de l'ITE Mémoire principale Fentes DDR3 DIMM x 4 Capacité mémoire maximale de 16 Go Chaque DIMM prend en charge des DDR3 de 512Mo/1Go/2Go/4Go Module de mémoire DDR3 à mode à double voie Prend en charge la DDR3 1066 / 1333 Prend en charge la DDR3 1600 (OC) / 1866 (OC) / 2133 (OC) Les DIMM à registres et DIMM avec code correcteurs d'erreurs ne sont pas prises en charge SATA 2 & 3 Contrôleur Serial ATA intégré : Taux de transfert jusqu'à 3.0Go/s / 6.0Go/s. Conforme à la spécification SATA Version 2.0 / 3.0 LAN Realtek RTL 8111E 10 / 100 / 1000 Mb/s négociation automatique Half / Full duplex capability Prise en charge audio HD ALC892 Prise en charge de l'audio haute définition Sortie audio à 7.1 voies USB3.0 NEC uPD720200 Taux de transfert de données jusqu'à 600 Mo / s IEEE 1394 VT6315N 1394a Fente PCI x2 Fente PCI Express Gen2 x16 x2 Fentes Fente PCI Express Gen2 x1 x2

SATA3 Connecteur SATA2 x3 Chaque connecteur prend en charge 1 périphérique SATA2 Connecteur du panneau avant x1 Prend en charge les équipements du panneau avant Connecteur Audio du panneau avant x1 Prend en charge la fonction audio du panneau avant Embase de ventilateur UC x1 Alimentation électrique du ventilateur UC (avec fonction de ventilateur intelligent) Embase de ventilateur système x2 Alimentation électrique du ventilateur système Embase d'effacement CMOS x1 Connecteur USB2.0 x3 Chaque connecteur prend en charge 2 ports USB2.0 de panneau avant Connecteur de IR du consommateur x1 Port série x1 Connecteur IEEE 1394 x1 Connecteur de sortie S/PDIF x1 Prend en charge la fonction de sortie audio numérique Connecteur d'alimentation x1 (24 broches) Connecteur embarqué Connecteur d'alimentation x2 (8 broches) E/S du panneau arrière Clavier PS/2 x1 RCA + Sortie S/PDIF x1 Port 1394 x1 Port eSATA x1 Port LAN x1 Port USB2.0 x6 Port USB3.0 x2 Fiche audio x6 USB3.0 dispositifs (par NEC uPD720200) USB2.0/USB1.X dispositifs (par P67) Dimensions de la carte 305 mm (l) X 244 mm (H) ATX Support SE Windows XP / Vista / 7 Biostar se réserve le droit d'ajouter ou de supprimer le support de SE avec ou sans préavis

Pentium / Celeron Supporto di Execute Disable Bit / Enhanced Intel SpeedStep® / Architettura Intel 64 / Tecnologia Extended Memory 64 / Tecnologia Virtualization / Hyper Threading Chipset Intel P67 Super I/O IT8728 Fornisce le funzionalità legacy Super I/O usate più comunemente. Interfaccia LPC (Low Pin Count) Funzioni di controllo dell’ambiente: Monitoraggio hardware Controller / Monitoraggio velocità ventolina Funzione "Smart Guardian" di ITE Memoria principale Alloggi DIMM DDR3 x 4 Capacità massima della memoria 16GB Ciascun DIMM supporta DDR3 512MB/1GB/2GB/4GB Modulo di memoria DDR3 a canale doppio Supporto di DDR3 1066 / 1333 Supporto di DDR3 1600 (OC) / 1866 (OC) / 2133 (OC) DIMM registrati e DIMM ECC non sono supportati SATA 2 & 3 Controller Serial ATA integrato Velocità di trasferimento dei dati fino a 3.0Gb/s / 6.0Gb/s. Compatibile specifiche SATA Versione 2.0/3.0 LAN Realtek RTL 8111E Negoziazione automatica 10 / 100 / 1000 Mb/s Capacità Half / Full Duplex Supporto audio HD ALC892 Supporto audio High-Definition (HD) Uscita audio 7.1 canali USB3.0 NEC uPD720200 Velocità di trasferimento dati fino a 600 MB / s IEEE 1394 VT6315N 1394a Alloggio PCI x2 Alloggio PCI Express Gen2 x16 x2 Alloggi Alloggio PCI Express Gen2 x1 x2

Connettore SATA2 x3 Ciascun connettore supporta 1 unità SATA2 Connettore pannello frontale x1 Supporta i servizi del pannello frontale Connettore audio frontale x1 Supporta la funzione audio pannello frontale Collettore ventolina CPU x1 Alimentazione ventolina CPU (con funzione Smart Fan) Collettore ventolina sistema x2 Alimentazione ventolina di sistema Collettore cancellazione CMOS x1 Connettore USB2.0 x3 Ciascun connettore supporta 2 porte USB2.0 pannello frontale Connettore IR del consumatore x1 Porta seriale x1 Connettore IEEE 1394 x1 Connettore output S/PDIF x1 Supporta la funzione d’output audio digitale Connettore alimentazione x1 (24 pin) Connettori su scheda Connettore alimentazione x2 (8 pin) I/O pannello posteriore Tastiera PS/2 x1 RCA + S/PDIF Fuori x1 Porta 1394 x1 Porta eSATA x1 Porta LAN x1 Porta USB2.0 x6 Porta USB3.0 x2 Connettore audio x6 USB3.0 dispositivi (da NEC uPD720200) USB2.0/USB1.X dispositivi (da P67) Dimension i scheda 305 mm (larghezza) x 244 mm (altezza) ATX Sistemi operativi supportati Windows XP / Vista / 7 Biostar si riserva il diritto di aggiungere o rimuovere il supporto di qualsiasi sistema operativo senza preavviso.

Celeron Admite Bit de deshabilitación de ejecución / Intel SpeedStep® Mejorado / Intel Architecture-64 / Tecnología Extended Memory 64 / Tecnología de virtualización / Hyper Threading Conjunto de chips Intel P67 Súper E/S IT8728 Le ofrece las funcionalidades heredadas de uso más común Súper E/S. Interfaz de cuenta Low Pin Iniciativas de control de entorno, Monitor hardware Controlador/monitor de velocidad de ventilador Función "Guardia inteligente" de ITE Memoria principal Ranuras DIMM DDR3 x 4 Capacidad máxima de memoria de 16GB Cada DIMM admite DDR de 512MB/1GB/2GB/4GB Módulo de memoria DDR3 de canal Doble Admite DDR3 de 1066 / 1333 Admite DDR3 de 1600(OC) / 1866(OC) / 2133(OC) No admite DIMM registrados o DIMM compatibles con ECC SATA 2 & 3 Controlador ATA Serie Integrado Tasas de transferencia de hasta 3.0 Gb/s / 6.0 Gb/s. Compatible con la versión SATA 2.0 / 3.0. Red Local Realtek RTL 8111E Negociación de 10 / 100 / 1000 Mb/s Funciones Half / Full dúplex Soporte de sonido HD ALC892 Soporte de sonido de Alta Definición Salida de sonido de 7.1 canales USB3.0 NEC uPD720200 Tasas de transferencia de datos hasta 600 MB / s IEEE 1394 VT6315N 1394a Ranura PCI X2 Ranura PCI Express Gen2 x16 X2 Ranuras Ranura PCI Express Gen2 x 1 X2

Conector SATA2 X3 Cada conector soporta 1 dispositivos SATA2 Conector de panel frontal X1 Soporta instalaciones en el panel frontal Conector de sonido frontal X1 Soporta funciones de sonido en el panel frontal Cabecera de ventilador de CPU X1 Fuente de alimentación de ventilador de CPU (con función Smart Fan) Cabecera de ventilador de sistema X2 Fuente de alimentación de ventilador de sistema Cabecera de borrado de CMOS X1 Conector USB2.0 X3 Cada conector soporta 2 puertos USB2.0 frontales Conector de IR del consumidor X1 Puerto serie X1 Cabecera IEEE 1394 x1 Conector de salida S/PDIF X1 Soporta función de salida de sonido digital Conector de alimentación X1 (24 patillas) Conectores en placa Conector de alimentación X2 (8 patillas) Panel trasero de E/S Teclado PS/2 X1 RCA + Salida S/PDIF x1 Puerto 1394 x1 Puerto eSATA X1 Puerto de red local X1 Puerto USB2.0 X6 Puerto USB3.0 X2 Conector de sonido X6 USB3.0 dispositivos (por NEC uPD720200) USB2.0/USB1.X dispositivos (por P67) Tamaño de la placa 305 mm. (A) X 244 Mm. (H) ATX Soporte de sistema operativo Windows XP / Vista / 7 Biostar se reserva el derecho de añadir o retirar el soporte de cualquier SO con o sin aviso previo.

Celeron Suporta as tecnologias Execute Disable Bit / Enhanced Intel SpeedStep® / Intel Arquitecture -64 / Extended Memory 64 / Virtualization / Hyper Threading Chipset Intel P67 Especificaçã o Super I/O IT8728 Proporciona as funcionalidades mais utilizadas em termos da especificação Super I/O. Interface LPC (Low Pin Count). Iniciativas para controlo do ambiente Monitorização do hardware Controlador/Monitor da velocidade da ventoinha Função "Smart Guardian" da ITE Memória principal Ranhuras DIMM DDR3 x 4 Capacidade máxima de memória: 16 GB Cada módulo DIMM suporta uma memória DDR3 de 512MB/ 1GB/2GB/4GB Módulo de memória DDR3 de canal duplo Suporta módulos DDR3 1066 / 1333 Suporta módulos DDR3 1600 (OC) / 1866 (OC) / 2133 (OC) Os módulos DIMM registados e os DIMM ECC não são suportados SATA 2 & 3 Controlador Serial ATA integrado Velocidades de transmissão de dados até 3.0 Gb/s / 6.0 Gb/s. Compatibilidade com a especificação SATA versão 2.0 / 3.0. LAN Realtek RTL 8111E Auto negociação de 10 / 100 / 1000 Mb/s Capacidade semi/full-duplex Suporte para áudio de alta definição ALC892 Suporta a especificação High-Definition Audio Saída de áudio de 7.1 canais USB3.0 NEC uPD720200 Taxas de transferência de dados até 600 MB / s IEEE 1394 VT6315N 1394a Ranhura PCI x2 Ranhura PCI Express Gen2 x16 x2 Ranhuras Ranhura PCI Express Gen2 x 1 x2

Conector SATA2 x3 Cada conector suporta 1 dispositivo SATA2 Conector do painel frontal x1 Para suporte de várias funções no painel frontal Conector de áudio frontal x1 Suporta a função de áudio no painel frontal Conector da ventoinha da CPU x1 Alimentação da ventoinha da CPU (com a função Smart Fan) Conector da ventoinha do sistema x2 Alimentação da ventoinha do sistema Conector para limpeza do CMOS x1 Conector USB2.0 x3 Cada conector suporta 2 portas USB2.0 no painel frontal Conector de IR do consumidor x1 Porta série x1 Conector IEEE 1394 x1 Conector de saída S/PDIF x1 Suporta a saída de áudio digital Conector de alimentação x1 (24 pinos) Conectores na placa Conector de alimentação x2 (8 pinos) Entradas/S aídas no painel traseiro Teclado PS/2 x1 RCA + Saída S/PDIF x1 Porta 1394 x1 Porta eSATA x1 Porta LAN x1 Porta USB2.0 x6 Porta USB3.0 x2 Tomada de áudio x6 USB3.0 dispositivos (por NEC uPD720200) USB2.0/USB1.X dispositivos (por P67) Tamanho da placa 305 mm (L) X 244 mm (A) ATX Sistemas operativos suportados Windows XP / Vista / 7 A Biostar reserva-se o direito de adicionar ou remover suporte para qualquer sistema operativo com ou sem aviso prévio.

Celeron Obsługa Execute Disable Bit / Enhanced Intel SpeedStep® / Intel Architecture-64 / Extended Memory 64 Technology / Virtualization Technology / Hyper Threading Chipset Intel P67 Pamięć główna Gniazda DDR3 DIMM x 4 Maks. wielkość pamięci 16GB Każde gniazdo DIMM obsługuje moduły 512MB/1GB/2GB/4GB DDR3 Moduł pamięci DDR3 z trybem podwójnego kanału Obsługa DDR3 1066 / 1333 Obsługa DDR3 1600 (OC) / 1866 (OC) / 2133 (OC) Brak obsługi Registered DIMM oraz ECC DIMM Super I/O IT8728 Zapewnia najbardziej powszechne funkcje Super I/O. Interfejs Low Pin Count Funkcje kontroli warunków pracy, Monitor H/W Kontroler/Monitor prędkości wentylatora Funkcja ITE "Smart Guardian" SATA 2 & 3 Zintegrowany kontroler Serial ATA Transfer danych do 3.0 Gb/s / 6.0 Gb/s. Zgodność ze specyfikacją SATA w wersji 2.0 / 3.0. LAN Realtek RTL 8111E 10 / 100 / 1000 Mb/s z automatyczną negocjacją szybkości Działanie w trybie połowicznego / pełnego dupleksu Obsługa audio HD ALC892 Obsługa High-Definition Audio 7.1 kanałowe wyjście audio USB3.0 NEC uPD720200 Cena transferu danych do 600 MB / s IEEE 1394 VT6315N 1394a Gniazdo PCI x2 Gniazdo PCI Express Gen2 x16 x2 Gniazda Gniazdo PCI Express Gen2 x 1 x2

Złącze SATA2 x3 Każde złącze obsługuje 1 urządzenie SATA2 Złącze panela przedniego x1 Obsługa elementów panela przedniego Przednie złącze audio x1 Obsługa funkcji audio na panelu przednim Złącze główkowe wentylatora procesora x1 Zasilanie wentylatora procesora (z funkcją Smart Fan) Złącze główkowe wentylatora systemowego x2 Zasilanie wentylatora systemowego Złącze główkowe kasowania CMOS x1 Złącze USB2.0 x3 Każde złącze obsługuje 2 porty USB2.0 na panelu przednim Złącze Konsument IR x1 Port szeregowy x1 Złącze IEEE 1394 x1 Złącze wyjścia S/PDIF x1 Obsługa funkcji cyfrowego wyjścia audio Złącze zasilania (24 pinowe) x1 Złącza wbudowane Złącze zasilania (8 pinowe) x2 Back Panel I/O Klawiatura PS/2 x1 RCA + wyjścia S/PDIF x1 Port 1394 x1 Port eSATA x1 Port LAN x1 Port USB2.0 x6 Port USB3.0 x2 Gniazdo audio x6 USB3.0 urządzeń (przez NEC uPD720200) USB2.0/USB1.X urządzeń (przez P67) Wymiary płyty 305 mm (S) X 244 mm (W) ATX Obsluga systemu operacyjne go Windows XP / Vista / 7 Biostar zastrzega sobie prawo dodawania lub odwoływania obsługi dowolnego systemu operacyjnego bez powiadomienia.

Celeron Поддержка технологий Execute Disable Bit / Enhanced Intel SpeedStep® / Intel Architecture-64 / Extended Memory 64 Technology / технологии виртуализация / Hyper Threading Набор микросхем Intel P67 Основная память Слоты DDR3 DIMM x 4 Максимальная ёмкость памяти 16 ГБ Каждый модуль DIMM поддерживает 512МБ/1ГБ/2ГБ/4ГБ DDR3 Модуль памяти с двухканальным режимом DDR3 Поддержка DDR3 1066 / 1333 Поддержка DDR3 1600(OC) / 1866(OC) / 2133(OC) Не поддерживает зарегистрированные модули DIMM and ECC DIMM Super I/O IT8728 Обеспечивает наиболее используемые действующие функциональные возможности Super I/O. Интерфейс с низким количеством выводов Инициативы по охране окружающей среды, Аппаратный монитор Регулятор скорости вентилятора/ монитор Функция ITE "Smart Guardian" (Интеллектуальная защита) SATA 2 & 3 Встроенное последовательное устройство управления ATA скорость передачи данных до 3.0 гигабит/с / 6.0 гигабит/с. Соответствие спецификации SATA версия 2.0/3.0 Локальная сеть Realtek RTL 8111E Автоматическое согласование 10 / 100 / 1000 Мб/с Частичная / полная дуплексная способность Звуковая поддержка жесткого диска ALC892 Звуковая поддержка High-Definition 7.1канальный звуковой выход USB3.0 NEC uPD720200 скорости передачи данных до 600 МБ / с IEEE 1394 VT6315N 1394a Слот PCI x2 Слот PCI Express Gen2 x16 x2 Слоты Слот PCI Express Gen2 x 1 x2

Разъём SATA2 x3 Каждый разъём поддерживает 1 устройство SATA2 Разъём на лицевой панели x1 Поддержка устройств на лицевой панели Входной звуковой разъём x1 Поддержка звуковых функций на лицевой панели Контактирующее приспособление вентилятора центрального процессора x1 Источник питания для вентилятора центрального процессора (с функцией интеллектуального вентилятора) Контактирующее приспособление вентилятора системы x2 Источник питания для вентилятора системы Открытое контактирующее приспособление CMOS x1 USB2.0-разъём x3 Каждый разъём поддерживает 2 USB2.0-порта на лицевой панели Разъём едока ИКЫЙ x1 Последовательный порт x1 IEEE 1394-разъём x1 Разъём вывода для S/PDIF x1 Поддержка вывода цифровой звуковой функции Разъем питания (24 вывод) x1 Встроенны й разъём Разъем питания (8 вывод) x2 Задняя панель средств ввода-выв ода Клавиатура PS/2 x1 RCA + вывода для S/PDIF x1 1394-порт x1 eSATA порт x1 Порт LAN x1 USB2.0-порт x6 USB3.0-порт x2 Гнездо для подключения наушников x6 USB3.0 устройств (по NEC uPD720200) USB2.0/USB1.X устройств (по P67) Размер панели 305 мм (Ш) X 244 мм (В) ATX Поддержка OS Windows XP / Vista / 7 Biostar сохраняет за собой право добавлять или удалять средства обеспечения для OS с или без предварительного уведомления.

SpeedStep® / Intel Architecture-64 / Extended Memory 64 Technology / Virtualization Technology / Hyper Threading Socket 1155 ﻣﻌﺎﻟﺠﺎتIntel Core i7 / i5 / i3 / Pentium / Celeron ﺑ ﺘﺮدد ی ﺼﻞ إﻟﻰ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰیﺔ Intel P67 ﻣﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ ﻓﺘﺤﺔDDR3 DIMM ﻋﺪد4 ﺳﻌﺔ ذاآﺮة ﻗﺼﻮى16 ﺝﻴﺠﺎ ﺑﺎیﺖ ﺗﺪﻋﻢ آﻞ ﻓﺘﺤﺔ DIMM ﺗﺪﻋﻢ ذاآﺮة ﻣﻦ ﻥﻮعDDR3 / ﺳﻌﺔ512 ﻣﻴﺠﺎ ﺑﺎیﺖ و1 / و2 / و4 ﺝﻴﺠﺎ ﺑﺎیﺖ وﺣﺪة ذاآﺮةDDR3 ﻣﺰدوﺝﺔ اﻟﻘ ﻨﺎة ﺗﺪﻋﻢ اﻟﺬاآﺮة ﻣﻦ ﻥﻮعDDR3 ﺳﻌﺎت1066 / 1333 ﻣﻴﺠﺎ ﺑﺎیﺖ ﻧѧﻮع ﻣﻦ اﻟﺬاآﺮة ﺗѧѧﺪﻋﻢDDR3 ﺳѧѧﻌﺎت1866 (OC) / 2133 (OC) / 1600(OC) ﺑﺎیѧѧѧѧѧﺖ ﻣﻴﺠѧﺎ ﻻ ﺗﺪﻋﻢ رﻗﺎﺋﻖ اﻟﺬاآﺮة DIMM وﺗﻠﻚ اﻟﺘﻲ ﻻ ﺗﺘﻮاﻓﻖ ﻣﻊECC اﻟﺬاآﺮة اﻟﺮﺋﻴﺴﻴﺔ وﺳﺎﺋﻞ اﻟﺘﺤﻜﻢ ﻓﻲ اﻟﺒﻴﺌﺔ : ﻣﺮاﻗﺐ ﻟﻤﻌﺮﻓﺔ ﺣﺎﻟﺔ اﻷﺝﻬﺰة ﻣﺮاﻗﺐ ﻓﻲ ﺳﺮﻋﺔ اﻟﻤﺮوﺣﺔ "وﻇﻴﻔﺔSmart Guardian" ﻣﻦITE IT8728 ﺗﻮﻓﺮ وﻇﻴﻔﺔ Super I/O اﻷآﺜﺮ اﺳﺘﺨﺪاﻣﺎً . ﺪﻋﻢﺗ ﺗﻘﻨﻴﺔ Low Pin Count Interface Super I/O إﻟѧﻰ ﺗﺼѧѧѧѧﻞ ﺑﺴѧѧѧѧﺮﻋﺎت اﻟﺒﻴﺎﻧѧѧѧѧѧѧѧѧﺎت ﻧﻘѧѧѧﻞ3.0 / ﺛﺎﻧﻴѧѧѧѧѧѧﺔ /ﺝﻴﺠﺎﺑѧѧѧѧѧﺖ6.0 .ﺛﺎﻧﻴѧѧѧѧѧѧﺔ /ﺝﻴﺠﺎﺑѧѧѧѧѧﺖ ﻣﻄﺎﺑﻘﺔ ﻟﻤﻮاﺹﻔﺎت SATA اﻹﺹﺪار 2.0 / 3.0. ﻣﺘﺤﻜﻢ Serial ATA ﻣﺘﻜﺎﻣﻞ SATA 2 & 3 ﺗﻔﺎوض ﺗﻠﻘﺎﺋﻲ 10 / 100 ﺑﺎیﺖ ﻣﻴﺠﺎ / و ﺙﺎﻥﻴﺔ1ﺙﺎﻥﻴﺔ /ﺑﺖ ﺠﺎﺝﻴ إﻣﻜﺎﻥﻴﺔ اﻟﻨﻘﻞ اﻟﻤﺰدوج اﻟﻜﺎﻣﻞ / اﻟﻨﺼﻔﻲ Realtek RTL 8111E ﺵﺒﻜﺔ داﺥﻠﻴﺔ ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ اﻟﺼﻮت ﻋﺎﻟﻲ اﻟﺘﻌﺮیﻒ ﻣﻦ 7.1 ﻗﻨﻮات ﻟﺨﺮج اﻟﺼﻮت ALC892 دﻋﻢ اﻟﺼﻮت ﻋﺎﻟﻲ اﻟﺘﻌﺮیﻒ إﻟѧѧﻰ ﺗﺼѧѧѧѧﻞ ﺑﻴﺎﻧѧѧѧѧѧѧѧﺎت ﻧﻘѧѧѧﻞ ﻣﻌﺪﻻت600 ﺛﺎﻧﻴѧѧѧѧѧѧﺔ / ﺑﺎیѧѧѧѧѧﺖ ﻣﻴﻐѧѧﺎ NEC uPD720200 USB3.0 1394a VT6315N IEEE 1394 ﻓﺘﺤﺔPCI ﻋﺪد2 ﻓﺘﺤﺔGen2 x16 PCI Express ﻋﺪد2 ﻓﺘﺤﺔPCI Express Gen2 x 1 ﻋﺪد2 اﻟﻔﺘﺤﺎت

ﻣﻨﻔﺬSATA3 ﻋﺪد2 یﺪﻋﻢ آﻞ ﻣﻨﻔﺬ واﺣﺪ ﻣﻦ أﺝﻬﺰةSATA2 ﻣﻨﻔﺬSATA2 ﻋﺪد3 یﺪﻋﻢ ﺗﺠﻬﻴﺰات اﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ ﻣﻨﻔﺬ اﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ ﻋﺪد 1 یﺪﻋﻢ وﻇﻴﻔﺔ اﻟﺼﻮت ﺑﺎﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ ﻣﻨﻔﺬ اﻟﺼﻮت اﻷﻣﺎﻣﻲ ﻋﺪد 1 ﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ ﻣﻊ وﻇﻴﻔﺔSmart Fan وﺹﻠﺔ ﻣﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰیﺔ ﻋﺪد 1 ﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ اﻟﻨﻈﺎم وﺹﻠﺔ ﻣﺮوﺣﺔ اﻟﻨﻈﺎم ﻋﺪد 2 وﺹﻠﺔ ﻣﺴﺢCMOS ﻋﺪد1 یﺪﻋﻢ آﻞ ﻣﻨﻔﺬ ﻓﺘﺤﺘﻲUSB2.0 ﺑﺎﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ ﻣﻨﻔﺬ USB2.0 ﻋﺪد3 ﻣﻨﻔﺬ اﻷﺣﻤﺮ ﺗﺤѧѧѧﺖ ﻣﺴѧѧѧѧѧﺘﻬﻠﻜﺔ ﻋﺪد 1 ﻣﻨﻔﺬ ﺗﺴﻠﺴﻠﻲ ﻋﺪد1 ﻣﻨﻔﺬIEEE 1394 ﻋﺪد1 یﺪﻋﻢ وﻇﻴﻔﺔ ﺥﺮج اﻟﺼﻮت اﻟﺮﻗﻤﻲ ﻣﻨﻔﺬ ﺥﺮج S/PDIF ﻋﺪد1 ﻣﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )24دﺑﻮس ( ﻋﺪد 1 ﻣﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )8دﺑﺎﺑﻴﺲ ( ﻋﺪد 2 اﻟﻤﻨﺎﻓﺬ ﻋﻠﻰ ﺳﻄﺢ اﻟﻠﻮﺣﺔ (NEC uPD720200 اﻷﺝﻬﺰة ) ﻗﺒѧѧѧѧѧﻞ ﻣﻦUSB3.0 (P67 اﻷﺝﻬﺰة ) ﻗﺒѧѧѧѧѧﻞ ﻣﻦUSB2.0/USB1.X ﻟﻮﺣﺔ ﻣﻔﺎﺗﻴﺢPS/2 ﻋﺪد1 RCA + S/PDIF Out ﻋﺪد1 ﻣﻨﺎﻓﺬ1394 ﻋﺪد1 ﻣﻨﻔﺬeSATA ﻋﺪد1 ﻣﻨﻔﺬ ﺵﺒﻜﺔ اﺗﺼﺎل ﻣﺤﻠﻴﺔ ﻋﺪد 1 ﻣﻨﺎﻓﺬUSB2.0 ﻋﺪد6 ﻣﻨﺎﻓﺬUSB3.0 ﻋﺪد2 ﻣﻘﺒﺲ ﺹﻮت ﻋﺪد 6 دﺥﻞ ﻣﻨﺎﻓﺬ ﺥﺮج / اﻟﻠﻮﺣﺔ اﻟﺨﻠﻔﻴﺔ ATX 305 )ﻣﻢ ﻋﺮض ( X 244 )ﻣﻢ ارﺗﻔﺎع ( ﺣﺠﻢ اﻟﻠﻮﺣﺔ ﺗﺤﺘﻔﻆ Biostar ﺑﺤﻘﻬﺎ ﻓﻲ إﺿﺎﻓﺔ أو إزاﻟﺔ اﻟﺪﻋﻢ ﻥﻈﺎم ﻷي ﺗﺸﻐﻴﻞ ﺑﺈﺥﻄﺎر أو ﺑﺪون إﺥﻄﺎر . Windows XP / Vista / 7 دﻋﻢ أﻥﻈﻤﺔ اﻟﺘﺸﻐﻴﻞ

セッサ Execute Disable Bit / Enhanced Intel SpeedStep® / Intel Architecture-64 / Extended Memory 64 Technology / Virtualization Technology / Hyper Threadingをサポートします チップセット Intel P67 メインメモリ DDR3 DIMMスロット x 4 最大メモリ容量16GB 各DIMMは 512MB/1GB/2GB/4GB DDR3をサ ポート デュアル チャンネルモードDDR3メモリモジュール DDR3 1066 / 1333 をサポート DDR3 1600(OC) / 1866(OC) / 2133(OC) をサポート 登録済みDIMMとECC DIMMはサポートされません Super I/O IT8728 もっとも一般に使用されるレガシーSuper I/O機 能を採用しています。 低ピンカウントインターフェイス 環境コントロールイニシアチブ、 H/Wモニター ファン速度コントローラ/ モニター ITEの「スマートガーディアン」機能 SATA 2 & 3 統合シリアルATAコントローラ 最高3.0 Gb/秒 / 6.0 Gb/秒のデータ転送速度 SATAバージョン2.0 / 3.0仕様に準拠。 LAN Realtek RTL 8111E 10 / 100 / 1000 Mb/秒のオートネゴシエーション 半/全二重機能 HDオーディ オのサポート ALC892 ハイデフィニションオーディオのサポート 7.1 チャンネルオーディオアウト USB3.0 NEC uPD720200 データ転送速度最大600 MB /秒の IEEE 1394 VT6315N 1394a PCIスロット x2 PCI Express Gen2 x16スロット x2 スロット PCI Express Gen2 x 1スロット x2

x1 1394ポート x1 eSATAポート x1 LANポート x1 USB2.0ポート x6 USB3.0ポート x2 オーディオジャック x6 USB3.0デバイス (で NEC uPD720200) USB2.0/USB1.Xデバイス (で P67) ボードサイズ 305 mm (幅) X 244 mm (高さ) ATX OSサポート Windows XP / Vista / 7 Biostarは事前のサポートなしにOSサポートを追加または 削除する権利を留保します。 2010/10/28