Chamberlain 195LM Manual 

Garage Door Opener Track Down Rod Bracket Structural Supports Down Rod Self-Tapping Bolt 5/16˝-18x1˝ Align the channels REAR VIEW Bracket Track Structural Supports Structural Support Lag Screw 5/16˝-9x1-5/8˝ Lag Screw 5/16˝-9x1-5/8˝ Garage Door Opener Garage Door Opener OPTION 1 OPTION 2 OPTION 1 Serrated Hex Flange Nut 5/16˝-18 Down Rod Bolt 5/16˝-18x3-1/4˝ Slide Mechanism Tighten nut to secure slide mechanism to track Track Cut from this end One-Piece Doors Only 4˝ X˝ X˝ Down Rod OR Wire Management Channel Crown Pan Head Screw 6-19 Track Down Rod Hex Nut 5/16˝-18 Lock Washer 5/16˝ Hex Head Cap Screw 5/16˝-18x7/8˝ REAR VIEW Bracket 1. FASTEN THE TRACK TO THE CEILING (FIGURE 1) Determine where the garage door opener will be installed. There are two option for installing the track: • Option 1 (Recommended): Install track perpendicular to the garage door opener rail. • Option 2: Install track parallel to the garage door opener rail. The track MUST be RIGIDLY fastened to structural support on ceiling using lag screws. NOTE: The down rod rotates +/-11 degrees only in the direction of the garage door. With option 2, the garage door opener will sway more when operating and the track MUST be centered with the garage door opener; no rotational adjustability left to right. Otherwise the garage door opener/rail may be at a slight angle when the garage door opener is mounted. 2. DETERMINE THE LENGTH OF THE DOWN ROD AND CUT TO LENGTH (FIGURE 2) To determine the length of the down rod, measure the distance from the ceiling to the top of the garage door opener, and then subtract 4". Cut the down rod using the template provided. DO NOT cut the end of the down rod with the holes, cut from the other end. Use a fi le to remove burrs from cut end, especially near the wire management channel. NOTE: For best results use a power saw with a vise for cutting the down rod straight and to protect the paint from chipping. A hack saw may be used but may not cut as straight and the paint will be more prone to chipping. 3. ATTACH THE BRACKET TO THE DOWN ROD (FIGURE 3) Attach the bracket to the down rod with the self-tapping bolt 5/16"-18 X 1" provided, tighten the bolt. Ensure the bolt is fully seated and tightened. Make sure the wire management channel on the down rod is aligned with wire management channel on the bracket. 4. ATTACH THE DOWN ROD TO THE SLIDE MECHANISM IN THE TRACK (FIGURE 4) Insert the 5/16”-18 X 3-1/4” bolt through the slide mechanism and down rod and attach with the serrated hex fl ange nut; this is for the pivot point of the kit. Move the slide mechanism along the track until the down rod is in a vertical orientation and tighten hardware. 5. ATTACH THE BRACKET (WITH DOWN ROD) TO THE GARAGE DOOR OPENER (FIGURE 5) Attach the bracket to the garage door opener with 5/16" lock washers, 5/16"-18 hex nuts, and 5/16"-18 X 7/8" hex head cap screws. Make sure the wire management channel is facing the power cord on the garage door opener. Tighten at this point. 6. ROUTE WIRES THROUGH THE WIRE MANAGEMENT CHANNEL (FIGURE 5) Route the power cord, safety reversing sensor wires and door control wires through the wire management channel. Measure and cut cover for the wire management channel. Snap cover onto down rod. Use a zip tie to secure all wires into one of the 4 holes in the slide mechanism. 7. COMPLETE INSTALLATION (FIGURE 5) Secure the crown together with the pan head screws 6-19 (2) provided. Track Down rod Bracket Crown (2) Cover (for wire management) Hardware bag: Lag screws 5/16"-9x1-5/8" (2), bolt 5/16"-18x3-1/4", hex nut with serrated washer head 5/16"- 18, self-tapping bolt 5/16"-18x1", screws 5/16"-18x7/8" (2), lock washers 5/16" (2), hex nuts 5/16"-18 (2), and pan head screws 6-19 (2) FIGURE 1 OVERVIEW FIGURE 4 FIGURE 3 FIGURE 2 FIGURE 5 CARTON INVENTORY To avoid possible SERIOUS INJURY from a falling garage door opener, fasten it SECURELY to structural supports of the garage. Concrete anchors MUST be used if installing track into masonry. For more information visit www.devancocanada.com

DEVANCO CANADA 19192 HAY ROAD, UNIT Q SUMMERSTOWN, ON K0C 2E0 TOLL FREE: 855-931-3334 www.devancocanada.com WHEN ORDERING REPAIR PARTS PLEASE SUPPLY THE FOLLOWING INFORMATION: � 3 PART NUMBER � 3 DESCRIPTION � 3 MODEL NUMBER