Cumberland Evolution S3 Owner's Manual

Secondary Sensing System CUMBERLAND Assumption, IL 62510 • Phone 217-226-4421 • Fax 217-226-4420 Secondary Sensing System Owners Manual Cumberland 1004 E. Illinois St. Assumption, IL 62510

Secondary Sensing System Table of Contents Table of Contents Section Description Page 1. Warnings .........................................................................................................................................................4 2. Ratings and Specifications ..............................................................................................................................5 3. Introduction ....................................................................................................................................................5 4. S3 Front Panel .................................................................................................................................................6 4.1 Control / Editor Section ..........................................................................................................................6 4.1.1 Temperature ....................................................................................................................................7 4.1.2 Target ..............................................................................................................................................7 4.1.3 High Limit .......................................................................................................................................8 4.1.4 Low Limit .......................................................................................................................................8 4.1.5 Status ...............................................................................................................................................9 4.1.6 History ............................................................................................................................................9 4.2 Alarm System Indicators ......................................................................................................................10 4.2.1 Conditions OK Indicator ...............................................................................................................10 4.2.2 Power ............................................................................................................................................10 4.2.3 Low Battery ..................................................................................................................................10 4.2.4 AUX 1 and AUX 2 .......................................................................................................................10 4.2.5 Control System Auxiliary .............................................................................................................11 4.2.6 Zone Temperature Section ............................................................................................................12 4.3 Back-Up System Indicators ..................................................................................................................12 4.3.1 Inlet Overrides Indicators .............................................................................................................12 4.3.2 Ventilation Back-Up Display and Selection Switch .....................................................................12 4.3.3 Back-Up Stages.............................................................................................................................12 4.4 Synchronize / Test Indicators ...............................................................................................................12 4.4.1 Synchronize Systems ....................................................................................................................13 4.4.2 Test/Acknowledge Alarm .............................................................................................................13 5. Program Mode ..............................................................................................................................................14 5.1 General Parameters ...............................................................................................................................14 5.2 PC Compatible Cumberland Network Parameters ...............................................................................16 5.3 Alarm Function Parameters ..................................................................................................................16 5.4 Sensor Calibration Parameters ..............................................................................................................16 6. General Operation .........................................................................................................................................17 6.1 Alarm Inputs .........................................................................................................................................17 6.1.1 Temperature Sensors #1 ,#2 and #3 ..............................................................................................17 6.1.2 Auxiliary Inputs #1, #2, and Control System ...............................................................................17 6.1.3 Power Out .....................................................................................................................................17 6.2 Alarm Outputs ......................................................................................................................................17 6.2.1 Siren ..............................................................................................................................................17 6.2.2 Dry Contact (N.O. and N.C. Contacts) .........................................................................................18 7. Back-Up System Operating Conditions ........................................................................................................19 7.1 Operation with the Evolution 3000/3001 .............................................................................................19 7.1.1 Normal S3 Back-Up Operation .....................................................................................................19 7.1.2 Emergency Operation ...................................................................................................................20 7.1.3 Override Operation .......................................................................................................................20 7.1.4 Fail-Safe Relay Operation .............................................................................................................21 7.1.5 Setting EV Back-Up Stage Jumpers .............................................................................................21 7.1.6 Vent/Tunnel Inlet Override Operation ..........................................................................................21 7.2 Operation as Stand-Alone System ........................................................................................................22 7.2.1 Normal S3 Back-Up Operation .....................................................................................................22 7.2.2 Minimum Ventilation Protection ..................................................................................................23 7.2.3 Fail-Safe Relay Strip .....................................................................................................................23 7.2.4 Vent/Tunnel Inlet Override Operation ..........................................................................................23 8. Trouble-Shooting Your Alarm .....................................................................................................................24 8.1 Low Battery ..........................................................................................................................................24 8.2 Power Out .............................................................................................................................................24 8.3 No Siren at Test ....................................................................................................................................24

Secondary Sensing System Table of Contents 8.4 Replacing the Fuses ..............................................................................................................................24 8.5 Temperature Sensors Disconnected ......................................................................................................25 8.6 Temperature Sensors Out of Calibration ..............................................................................................25 8.7 Trouble-Shooting the Auxiliaries .........................................................................................................25 9. Controller Installation and Setup ..................................................................................................................25 9.1 Tools Required .....................................................................................................................................25 9.2 Installation Instructions ........................................................................................................................25 9.3 Sensor Recommendations .....................................................................................................................26 10. Maintenance ..............................................................................................................................................27 11. Wiring Diagrams, Schematics, etc. ...........................................................................................................27 11.1 S3 Internal Electrical Wiring .................................................................................................................27 11.2 S3 Circuit Board Layout .......................................................................................................................28 11.3 Connecting AC Power to the S3 ...........................................................................................................29 11.4 Connecting Sensors to the S3 ................................................................................................................30 11.5 S3 PowerTrak Override Settings and Wiring ........................................................................................31 11.6 S3 Relay Card Wiring ...........................................................................................................................32 11.7 Connecting an Alarm or Siren to the S3 ................................................................................................33 11.8 Connecting Auxiliary Inputs to the S3 ..................................................................................................34 11.9 Connecting Other Cumberland Controllers to the S3 Auxiliary Input ..................................................35 11.10 Connecting Local Network Connections to the S3 ...............................................................................36 11.11 Connecting the S3 to the HH.Net ..........................................................................................................37 12. Replacement and Optional Parts ...............................................................................................................38 13. Temperature vs. Sensor Resistance Table ................................................................................................39 14. Error Codes ...............................................................................................................................................40 15. S3 Program Label ......................................................................................................................................40 16. Warranty ...................................................................................................................................................41

Secondary Sensing System 4 of 42 1. Warnings Warning! Maximum operating temperature of controller is 50° C (122° F). Use adequate ventilation to reduce the risk of overheating controller! Warning! • Do not perform modifications or wiring with voltage applied! • Keep high voltage (or AC) separate from low voltage wires! Warning! When this controller is used in a life support heating and ventilation system where failure could result in loss or injury, the user should provide adequate back-up, or accept the risk of such loss or injury!

Secondary Sensing System 5 of 42 2. Ratings and Specifications • Power Supply…………………240VAC 50/60 Hz • Temperature Range…………..32°F - 122°F (0°C – 50°C) • Inputs………………………....Three thermistor temperature sensors 32°F – 120°F (0°C - 49°C) Three auxiliary inputs (contact closure) • Outputs………………………..One siren (1.0 Amps @ 12VDC) One dry contact (5 Amps @ 240 VAC) 4 - 1 Hp Stage Outputs (Plus Model ONLY) 3. Introduction The Evolution Secondary Sensing System, also known as S3 (S cubed), is a unique control system. It combines the features of two systems into one. The S3 is an alarm system that has the added abilities of the Evolution Back- Up System. It combines these functions to provide ultimate security at a lower system cost. • Alarm System First, it functions as an alarm system to warn or alert of problem conditions such as Power Outage, High or Low temperature conditions, and/or out of range conditions in other devices through auxiliary switch inputs such as alarm relays. It contains an alarm relay that is capable of driving a 12 volt audible siren and also capable of signaling an external dialer through a N.O./N.C. contact. The S3 is capable of monitoring up to three auxiliary alarm inputs. It can also monitor up to three temperature sensors for out of range conditions which allows the S3 the flexibility to monitor any brood setup. In addition, the S3 has a built in Cycle Pressure Alarm that can be used in conjunction with a static pressure switch or a Photohelic gauge to provide a minimum ventilation monitor. • Back-Up System As an added bonus, the S3 can also act as the buildings Back-Up System. All of the functionality of the Evolution Back-Up System is packed into this unit. Therefore, as with the Evolution Back-Up System, it is capable of driving up to 32 of the Evolution 3000/3001 relay outputs, it can override the vent or tunnel inlets based on the level of Back-Up necessary, and it contains a back-up timer percentage capable of assisting in minimum ventilation. This unit is also not limited to use with the Evolution 3000/3001. With the addition of a fail-safe relay card, this unit is capable of driving four 1 h.p. loads directly. Therefore, it is capable of being used with any control system. (Note: If used with control systems other than the Evolution 3000/3001, some functionality will be lost.) • Additional Benefits By combining the alarm system and the Back-Up system, the S3 adds additional benefits other than the obvious benefit of a lower system cost. The added benefits include the addition of another Back-Up temperature sensor, a back-up battery to provide power in the case of a breaker failure or a power supply fuse failure, and an additional back-up stage delay which delays turning equipment on after a power failure to allow proper generator start-up. In addition to the above features and benefits, the design of this system focused on providing a system that was more user-friendly and beneficial to the end user. The S3 added a target temperature in addition to the High and Low limits for the alarm and the Back-Up System. The High and Low limits are based off of this target, therefore, keeping your alarm and back-up limits in line is as easy as matching the target temperature of your S3 with the main systems target temperature. In fact, when used in conjunction with the Evolution 3000/3001 controllers, it is as easy as pressing the “Synchronize” button. Another added benefit is the addition of an on board history that tracks high and low temperatures, alarm conditions, and back-up conditions.

Secondary Sensing System 6 of 42 Secondary Sensing System Front Panel Control / Editor Section Back-Up Section Zone Temperature Section Synchronize / Test Section Power Switch Alarm Status Section 4. S3 Front Panel The S3 has five main sections on the faceplate. These are the Zone Temperature Section, the Back-Up Section, the Control / Editor Section, the Synchronize / Test Section, and the Alarm Status Section. The S3 Power Switch is located on the left side of the controller box as shown below. The switch controls power to the S3 controller and to the back-up battery. 4.1 Control / Editor Section Just below the Back-Up Section on the right hand side of the controller is the Control / Editor Section. This section has three buttons: Mode, Plus (+) and Minus (–). The Mode button is used to navigate thru settings and conditions. When the Mode button is momentarily pressed, the green LED Indicators changes to the next reading. By pressing and holding the Mode button for at least 5 seconds, the S3 can be placed in the Program Mode as discussed in Section 5 of this manual. Press the Plus (+) or Minus (-) button to change the values (readings) in the Ventilation Back-Up Display or Zone Temperature Section Displays depending on the specific display selected. Control / Editor Green Indicator LED’s show the type of information represented. For example, if the green light beside “Temperature” is lit, then the Zone Displays are showing the current readings from sensors. The other options for the Display Indicators are Target, High Limit, Low Limit, Status, and History. These modes are changed by momentarily pressing the Mode button. Each press of the Mode button steps the Display Indicator to the next reading Mode. LED Indicators + Scroll Button - Scroll Button Mode Button

Secondary Sensing System 7 of 42 4.1.1 Temperature The specific Zone Temperature (Zone 1, 2, or 3) lists the individual sensor temperature for each zone. The Ventilation Back-Up Temperature shown will be the average of the enabled sensors (Zone 1, 2, and/or 3). In the Zone Temperature Section, a reading of “--.-“ indicates the sensor is disconnected or in error. Also, if the display is flashing “OFF”, it means the sensor is disabled. Therefore, it will not cause the alarm to sound or be included in the Back-Up System’s average temperature. The Ventilation Back-Up Temperature displays the average of the enabled Zone Temperature Sensors. 4.1.2 Target The Target mode displays the target temperature used for Zone Alarm Limits and Back-Up Limits. The Zone Alarm Limits and the Back-Up Limits are referenced to the target much like that of a stage on point in a controller. Therefore, once initially set, the user will only adjust the target which will automatically adjust the high and low limits appropriately. The Target temperature can be changed (0.5° increments) using the Plus (+) or Minus (–) buttons. Example: If the Target Temperature is set to 80.0° F; The High Zone Limit temperature is set to 92.0° F; The Back-Up High Limit temperature set to 90.0° F; When the Target is dropped to 70.0° F, the High Zone Limits will change to 82.0° F and the Back-Up High Limit temperature will change to 80.0° F. Ventilation Back-Up Temperature Specific Zone Temperatures Target Temperature

Secondary Sensing System 8 of 42 4.1.3 High Limit The High Alarm Temperature is the high temperature at which the controller will indicate an alarm condition. The High Alarm Temperature is displayed and can be changed using Zone Input Switches (Zones 1, 2, or 3) then using the Plus (+) or Minus (–) buttons. The High Back-Up Limit is the high temperature at which Cool 1 of the Back-Up will turn ON. See Section 7 (Back-Up Operating Conditions). The High Back-Up Temperature is displayed and can be changed (1.0° increments) using the Select Button then using the Plus (+) or Minus (–) buttons. NOTE: The High & Low Limits for the temperature sensors can be set individually or can be programmed to be identical using program parameter P2 (See Section 5). 4.1.4 Low Limit The Low Alarm Temperature is the low temperature at which the controller will indicate an alarm condition. The Low Alarm Temperature is displayed and can be changed using Zone Input Switches (Zones 1, 2, or 3) then using the Plus (+) or Minus (–) buttons. The Low Back-Up Limit is the low temperature at which Heat of the Back-Up will turn ON. See Section 7 (Back-Up Operating Conditions). The Low Back-Up Temperature is displayed and can be changed (1.0° increments) using the Select Button then using the Plus (+) or Minus (–) buttons. NOTE: The High & Low Limits for the temperature sensors can be set individually or can be programmed to be identical using program parameter P2 (See Section 5). High Back-Up Limit Temperature High Alarm Limit Temperatures for Specific Zones Zone Input Switches Select Switch Low Back-Up Limit Temperature Low Alarm Limit Temperatures for Specific Zones Zone Input Switches Select Switch

Secondary Sensing System 9 of 42 4.1.5 Status The Status Mode displays the Sensor Status (ON or OFF) for each specific zone. This setting is used to remove unused sensors or to deactivate sensors outside of the brood area during ½ or ¾ brood conditions. Use the Zone Switches for selecting the specific Zone Temperature Sensor then using the + (ON) or – (OFF) buttons to enable or disable sensors. 4.1.6 History The History Mode displays the High and Low Temperatures for each specific zone, any Back-Up stages which have turned ON, as well as any alarm conditions which have occurred since the last reset. The History Reset function is displayed after pressing the Mode Button once after the Low Temp is displayed. The Zone 1 display will indicate “HIS” and the Zone 2 display will indicate “no” initially. Press the “+” button for selecting YES, then press the Mode button to confirm the History Reset to reset all control history. A new feature added in version V0.10 and later software allows automatic resetting of the on-board history anytime the Synchronize button is pressed. Status for Specific Zones Zone Switches Status for Specific Zones (High or Low Temperature Mode) Temperatures for Specific Zones High Temp Low Temp Reset Press Display History Selection Sequence Press

Secondary Sensing System 10 of 42 4.2 Alarm System Indicators The Alarm Status LED Display indicates if all Conditions are OK (Green LED) or the specific reason for the alarm condition (Red LED’s). If a red Alarm LED is blinking, the problem may be one of two causes: a. If Conditions OK LED is Green, an Alarm condition exists although the 30 second confirmation timer has not expired. b. If Conditions OK LED is OFF, the alarm condition has been acknowledged (Acknowledge LED will also be ON). Except for the Conditions OK (status) indicator, all of the remaining LED Indicators have red LED’s for displaying alarm status information. 4.2.1 Conditions OK Indicator At the top of the Alarm Status Indicators section is an LED indicator labeled “Conditions OK”. This indicator shows the current alarm status of the S3. If the Conditions OK LED is green, there are no alarms being generated. If the LED indicator is OFF, the S3 is in the alarm mode. When the LED is OFF, refer to the other Alarm Status Indicators for specific alarm condition information. 4.2.2 Power When this RED LED turns ON, the S3 control has lost AC power or the F1 fuse is blown. Refer to Section 8.4 for fuse replacement information. 4.2.3 Low Battery When the Low Battery RED LED indicator turns ON during loss of AC power, the battery level is partially depleted and currently operating at a low energy level. If the battery voltage has dropped below about 10.6 volts, the red LED Indicator will light. If the battery indicates low, the operator should set all controls so that the siren will not activate, and leave the machine plugged in for about four hours. This should recharge the battery. If this doesn’t work the battery is probably bad. In this case, contact your Cumberland dealer for a replacement. Note that it is common for the Low Battery indicator to be lit if the alarm has sounded for a long time. 4.2.4 AUX 1 and AUX 2 The designated alarm condition exists when the AUX 1 and/or AUX 2 RED LED turns ON. The Auxiliary inputs can be connected to a variety of external control sources such as curtain drops, control alarm outputs, pressure switch, or any device with a NC (Normally Closed) dry contact connection. The white area to the right of the LED indicator can be used to write-in the alarm title/description by using a Write-In Areas (for Auxiliary Alarms) LED Indicators (for Control System Alarms) LED Indicators (for Status and Alarms) Alarm Indicators

Secondary Sensing System 11 of 42 Control System TEMPERATURE: The temperature is beyond the alarm limits. PRESSURE: Indicates a High, Low, or Cycle Pressure alarm. WATER SYSTEM: Indicates High or Low water usage. FEED SYSTEM: Indicates a feed auger excessive runtime alarm. SPECIAL FEATURES IF USED WITH EVOLUTION 3000/3001 permanent fine-tipped marker. Each auxiliary alarm can be individually enabled or disabled by using the circuit board jumpers. Refer to the Circuit Board Layout in Section 11.2. If the jumper is installed, the AUX 1 or AUX 2 alarm is Disabled; If the jumper is removed, the AUX 1 alarm is Enabled. 4.2.5 Control System Auxiliary The Control System auxiliary input is a special input that should be connected to the main control system. It operates similar to Aux1 and Aux2 and yet has special functions associated with it to provide better protection for the building. The functions are different when the unit is connected to an Evolution 3000/3001 and when it is connected to another type control system. The following details the differences. Operation with Evolution 3000/3001: If connected to a Evolution 3000/3001, there is a communication network that allows communication of the alarm data from the main system to the S3. This allows the system to alarm even if the hard-wired connection to the Control System Auxiliary does not exist. It also allows the S3 to provide more detail as to what problem exist using the four LEDs located just below the Control System indication. The following picture highlights these indicators. The CONTROL SYSTEM alarm can be enabled or disabled by using the circuit board jumpers. Refer to the Circuit Board Layout in Section 11.2. If the jumper is installed, the CONTROL SYSTEM alarm is Disabled; If the jumper is removed, the CONTROL SYSTEM alarm is Enabled. The Evolution controller communicates with the S3 to display the four alarms described below: Operation without the Evolution 3000/3001: If the unit is used with another type control system, the Control System Auxiliary can take on other functions on top of just being an alarm. This input can function in one of two ways depending on the setting in program parameter P62 (See Section 5). If “P62 = On”, the input becomes a Cycle Pressure input. Therefore, while connected to a Photohelic, or Static Pressure switch, it will monitor the static pressure through the timer cycle period (P63). If it does not see a static pressure spike during this cycle, it will assume that the minimum ventilation is not working. Therefore, it will sound the alarm and also trigger the Back-Up system to run the “Cool1” backup stage on a minimum ventilation cycle. The minimum ventilation cycle is five minutes and the runtime will be based on the setting in P3 (See Section P62 = On – Cycle Pressure Alarm Enabled 5). If “P62 = OFF”, the input is a normal auxiliary input that will function in much the same way as Aux1 and Aux2. There is one distinction. If the S3 detects the alarm signal on this input, it will not only sound the alarm but it will also trigger the Back-Up System to run the “Cool1” backup stage on a minimum ventilation cycle. The minimum ventilation cycle is five minutes and the runtime will be based on the setting in P3 (See Section P62 = OFF – Cycle Pressure Alarm Disabled 5).

Secondary Sensing System 12 of 42 4.2.6 Zone Temperature Section The Zone Temperature Section shows the specific zone alarm status and control settings for the temperature alarms. If the Alarm Indicator is ON, that particular Zone is out of its temperature range based on the High and Low Limits. 4.3 Back-Up System Indicators The Back-Up System Indicators display the Back-Up operation status and control settings. Refer to Section 7 for additional information. 4.3.1 Inlet Overrides Indicators The Inlet Override Indicators indicate if the Back-Up is calling for vent inlets or tunnel inlets to open. Vent inlets operate with Cool 1; Tunnel inlets operate with Cool 3. 4.3.2 Ventilation Back-Up Display and Selection Switch The Ventilation Back-Up Display and Selection Switch are used to select and change the back-up settings. Refer to Section 7 for additional information. 4.3.3 Back-Up Stages The Back-Up Stages Indicators indicate if the Heat, Cool 1, Cool 2, or Cool3 stages are ON or OFF. If Cool 1 is flashing, it indicates that it is operating on a minimum ventilation timer. Refer to Section 7.1.1 for additional information. 4.4 Synchronize / Test Indicators The Synchronize / Test Section include two functions. Synchronize Systems and Test/Acknowledge Alarm. Alarm Indicators Zone Selection Switches Zone Temperature/ Settings Displays Temperature/Settings Display Selection Switch Back-Up Stages Indicators Ventilation Back-Up Display & Selector Inlet Overrides Indicators

Secondary Sensing System 13 of 42 4.4.1 Synchronize Systems The Synchronize Systems feature is used with the EV-3000 or EV-3001 controller to update the S3 target temperatures to the match the controller target temperatures and also automatically reset the on-board history. The on-board history automatic reset is a new feature added in version V0.10 and later software. If the S3 and the EV-3000 or EV-3001 temperature targets do not reflect the same information, the Synchronize Systems LED will flash. Press the Select button to automatically Synchronize the target temperatures and reset the on-board history. When the Synchronize Systems Select button is pressed, the target temperatures of the S3 will be changed to match the Evolution 3000/3001 controller target temperatures. It will also be displayed in the Back-Up display for verification. 4.4.2 Test/Acknowledge Alarm The Test/Acknowledge Alarm Section has two functions. It allows the user the ability to test the alarm contacts or the ability to silence (acknowledge) an active alarm.  Testing Alarm Contacts To test the Alarm contacts, the user can simply press and hold the “Select” button next to the Test/Acknowledge Alarm indicator. This allows the user the ability to manually test his alarm siren and/or alarm dialer. As long as the button is depressed, it will activate the alarm relay irregardless of the conditions that exist. In applications that use audible sirens, it is recommended that the operator press the Test/Acknowledge Alarm button for at least five seconds twice a week. In addition to insuring that the alarm is working correctly, the sounding of the alarm helps to condition that livestock or poultry so they are not shocked by the sound when an emergency condition arises.  Acknowledging Alarms If an active alarm condition exists, you can silence the audible siren, phone dialer, etc. once you arrive by pressing this button. This indicates to the alarm that you are acknowledging the problem; therefore, it disables the alarm contacts. If a different alarm occurs after the acknowledgement, the alarm contacts will be re-enabled. After an acknowledgement, the alarm indicator will continue to blink and the indicator beside the Test/Acknowledge Alarm section will also be on. This acknowledged condition is reset by only two ways. First, the alarm condition is corrected; secondly, the AC power and the battery power are removed from the controller. Test/Acknowledge Alarm Select Buttons Test/ Acknowledge Alarm LED Display Synchronize Systems Select Buttons Synchronize Systems LED Displays

Secondary Sensing System 14 of 42 5. Program Mode By pressing and holding the Mode button for at least 5 seconds, the S3 can be placed in the Program Mode as discussed below and on the following pages. Settings that are usually set up once per grow-out or maybe even just for summer or winter are referred to as program parameters and are accessed by taking the controller to program mode. To get to program mode, press and hold the “Mode” button for five seconds. When the controller has entered program mode, the Zone 1 display will show the first parameter (P1) and the Zone 2 display will show the current setting of parameter P1 (either C or F). The “Pxx” is known as a parameter number. All the program items for the controller have a unique parameter number assigned to them. The numbers are listed in the following subsections with a short description of each parameter. When in program mode, you change the value of certain parameters by using the + and - buttons as needed. When you have finished with the current setting, press the “Mode” button to move to the next parameter. 5.1 General Parameters General parameters are associated with the operation and control of the S3: P1 – Temperature Limits This general parameter selects either Celsius (C = Celsius) or Fahrenheit (F = Fahrenheit) temperature units. If P1 is set to “C”, the temperature units will be displayed in Celsius. If P1 is set to “F”, the temperature units will be displayed in Fahrenheit. P2 – Individual Sensor Limits This general parameter determines how to program the Sensor High and Low temperature limits. As indicated earlier, these limits can be set individually to different values. However, if it is desired to set Sensor 1, Sensor 2, and Sensor 3 to the same values, this parameter changes the programming procedure to allow limits to be entered only once but used for all sensors. If P2 is set to “YES”, the high and low sensor limits are entered individually. If P2 is “NO” limits are entered once for all sensors. To change the value of P2, press the Plus (+) button for “YES” or the Minus (-) button for “NO”. Parameter Number Parameter Setting

Secondary Sensing System 15 of 42 P3 – Back-Up Timer Percentage This determines the percentage that COOL 1 will be run in an Emergency condition for minimum ventilation. (10% to 100%). The timer is a five minute timer. A new timer percentage curve feature (added in version V0.09 and later software) automatically changes the timer percentage based on the Target Temperature. The data and table below shows an example: The table and graph above is representative of the curve. The curve actually has multiple points as the Target Temperature changes in between these points. The Emergency Back-Up Timer Percentage is not user selectable although you can view the current timer percentage by going to Program Mode and displaying P3. As you can see by the table, once the Target Temperature gets to 70 F (21.1 C) or less, the timer fan will run 100% of the time. In other words, Cool 1 will always run in the event that the main controller is lost or has a problem operating its timer fans. Timer percentages in between 70 – 100% are not implemented because frequent on-off transitions are very hard on single phase AC motors. P4 – Back-Up Stage On Delay This determines the number of seconds that the S3 will wait before turning Stages ON during power loss (10 to 60 seconds). This feature is designed to help with generator start-up. P5 – Fail-Safe Vent Inlets This determines whether the “Vent Inlet” relay operates with a normal action or a fail-safe action. If “Yes” (Fail-Safe Action) is chosen, the relay will default to allow the inlet machine to “Open” under extreme failure. Example – Power removed. If “No” (Normal Action) is chosen, the relay will default to allow the main controller control of the inlet. If “Fail-Safe” mode is chosen, the wiring must be reversed as shown in Section 11.5 wiring diagram. IMPORTANT 11.5 : It is important to ensure that the correct wiring connections are implemented with the specific P5 or P6 setting selection. Section shows the required wiring for Normal Action (P5/P6 = “No”) and also the required wiring for Fail-Safe Action (P5/P6 = “Yes”). P6 – Fail-Safe Tunnel Inlets This determines whether the “Tunnel Inlet” relay operates with a normal action or a fail-safe action. If “Yes” (Fail-Safe Action) is chosen, the relay will default to allow the inlet machine to “Open” under extreme failure. Example – Power removed. If “No” (Normal Action) is chosen, the relay will default to allow the main controller control of the inlet. If “Fail-Safe” mode is chosen, the wiring must be reversed as shown in Section 11.5 wiring diagram.

Secondary Sensing System 16 of 42 5.2 PC Compatible Cumberland Network Parameters These parameters are used with Cumberland’s Farm Manager Software. The controller has four parameters which are used to function with the Cumberland PC compatible inter-controller network (HH.Net). P40 – HHNet Address HH.Net permits up to 32 controllers to be addressed on a single communications port of a personal computer (PC). In order for the computer to recognize the communications from the controllers, each controller must have a unique network address. P41 – Version Number This is not settable by the user. It is the version of the controller software. P42 – Controller Setup This is not settable by the user. It is a unique number that allows the network software (Farm Manager) to recognize the type of controller. P43 – Local Network Enable The Local Network Enable feature enables the S3 to communicate with an Evolution 3000/3001 controller. If connected to an Evolution 3000/3001 and the Back-Up is enabled, the setting will automatically change to Yes. No = Not Connected [Stand-Alone]; Yes = Connected [EV Network] 5.3 Alarm Function Parameters The Alarm Function Parameters operate special alarm features. NOTE: These Features Are Automatically Disabled If Connected To The Evolution 3000/3001 Controller. P62 – Cycle Pressure Alarm The Cycle Pressure Alarm is setup to monitor minimum ventilation. It uses a pressure switch or other pressure/timer fan monitoring device and must be connected to Control Aux. This setting changes the operation of the control system auxiliary alarm. Contrary to its normal operation where an open signal would trigger an alarm, it will actually be looking for an open signal during the Minimum Vent Cycle Time (P63). If it does not see the open signal during this period, it will sound the alarm and trigger the Back-Up system to run “Cool 1” on a minimum ventilation timer cycle. (ON = Enabled; OFF = Disabled) P63 – Minimum Vent Cycle Time The Minimum Cycle Time is the time in minutes which is being used to provide minimum ventilation such as 5 or 10 minute timers. (Cycle time for timer fans) 5.4 Sensor Calibration Parameters The S3 has three temperature sensors that can be calibrated. The parameter(s) for calibration are PSx where x is the sensor number. NOTE: A sensor should never be calibrated more than 8 degrees. If a setting is that far out of range, it indicates that there is a problem other than sensor calibration. PS1 - Calibrate Sensor 1 This is the calibration temperature for Sensor 1. Instructions: With the controller operating, use a digital thermometer or similar independent temperature measuring device to measure the temperature at Sensor 1 location. With PS1 selected, use the Plus (+) and Minus (-) buttons to set the calibration temperature to the thermometer reading. PS2 - Calibrate Sensor 2 This is the calibration temperature for Sensor 2. Instructions: Same as Sensor 1 except substitute PS2 for PS1 in the instructions above. PS3 - Calibrate Sensor 3 This is the calibration temperature for Sensor 3. Instructions: Same as Sensor 1 except substitute PS3 for PS1 in the instructions above.

Secondary Sensing System 17 of 42 6. General Operation 6.1 Alarm Inputs The S3 has seven inputs that can be used to sound an alarm; Three from temperature sensors, three auxiliaries, and one for power out. The temperature sensors can be enabled or disabled. If a sensor is enabled it will be used to generate an alarm. If a sensor is disabled, it will not generate an alarm, even if the S3 determines that its readings are out of limits. The Auxiliary and Power Out inputs are always enabled. The seven alarm inputs are: 6.1.1 Temperature Sensors #1 ,#2 and #3 The S3 comes from the factory with three temperature sensors. The S3 will trigger an alarm if the temperature goes above the high limit setpoint or below the low limit setpoint of the sensors. The S3 will wait 30 seconds after a sensor indicates it is out of range before triggering an alarm. 6.1.2 Auxiliary Inputs #1, #2, and Control System The S3 is equipped with three auxiliary inputs. These inputs are connected in a closed loop circuit. On the circuit board located on the door of the alarm enclosure there is a terminal block for connecting the Auxiliary Inputs (See Section 11.8 for a connection diagram). Each of the connections has an IN and OUT terminal. If, at any time, the connection between the IN and OUT positions is broken (opened), the alarm will sound. There are many devices on the market that could be used with these inputs. For instance, water pressure switches, light meters, and thermostats could all be used. The S3 will wait 30 seconds after an auxiliary input is broken before triggering an alarm. 6.1.3 Power Out The Power Out alarm indicates that there has been no AC electricity present on the alarm power feed for at least 30 seconds. AC Power Fuse: If it is found that there is power present at the electrical outlet and the Power Alarm is ON at the S3, the 3 Amp slow-blow fuse located on the S3 circuit board (Fuse F1) should be checked for a blown fuse. To replace a fuse, disconnect AC power, disconnect the positive (+) battery terminal from the battery, carefully replace the blown fuse with the correctly sized replacement fuse, reconnect the positive (+) battery terminal to the battery, reapply AC power, and verify the power alarm has cleared. The S3 will wait 60 seconds after a Power Out indication before triggering an alarm. Refer to the S3 Circuit Board Layout in Section 11.2 and Fuse Replacement in Section 8.4. Terminal Connections to the Battery: If AC power is out or disconnected from the S3 AND none of the S3 Displays or LED’s are ON, verify that the Battery Positive (+) and Battery Negative (-) quick-connect terminals are securely attached to the battery. Refer to the S3 Wiring in Section 11.2. If the AC power is OFF for an extended period of time with the alarms ON, the Back-Up Battery will eventually be drained of all power. Refer to Section 8 for additional troubleshooting information. 6.2 Alarm Outputs The S3 has two alarm outputs. These can be used individually or simultaneously. The alarm outputs are: 6.2.1 Siren The siren hookup to the S3 will deliver a 12 volt DC signal with a current up to 1.0 amps. Many operators want to mount the siren a long distance from the controller. Sometimes, this is desirable in order to locate the siren closer to their dwelling, sometimes to get it away from their animals. The use of a small gauge wire to connect the Alert Alarm to the siren could cause a great deal of voltage drop. This voltage drop, in turn, can cause the siren to become inoperative. If the operator wants to mount the siren more than 50 feet from the controller, a relay with a 12VDC rated coil should be used to switch current to the siren. When a relay is added, the operator must provide a separate battery and charger for the siren circuit.

Secondary Sensing System 18 of 42 6.2.2 Dry Contact (N.O. and N.C. Contacts) The S3 provides a set of dry contacts that can be used to trigger a modem, auto-dialer or other auxiliary equipment. Both normally open (N.O.) and normally closed (N.C.) contacts are available. See Section 11.7 for a wiring diagram.

Secondary Sensing System 19 of 42 SPECIAL FEATURES IF CONNECTED TO EVOLUTION 3000/3001 7. Back-Up System Operating Conditions The S3 Back-Up System operates differently based on whether it is connected to a Evolution 3000/3001 control system or if it is a stand-alone (not connected to the Evolution 3000/3001 local network) system. Of course the system loses some of its functionality when it is not connected to the Evolution 3000/3001 network but its capabilities are still much better than other Back-Up system alternatives. This section will be divided into two sub- sections. Important! Before continuing, one must determine which type of system is installed for this specific application. If the S3 is connected to a Cumberland Evolution 3000 or Evolution 3001, refer to Section 7.1 for a description of the Back-Up operation with the Evolution 3000/3001. Otherwise, refer to Section 7.2 for Back-Up operation as Stand-Alone System. 7.1 Operation with the Evolution 3000/3001 7.1.1 Normal S3 Back-Up Operation During Normal Operation, the S3 always maintains the temperature between its high and low limits. It accomplishes this by using its temperature sensors and its four stage outputs. If the temperature drops below the Low Limit, the Heat stage will come on. That stage will not turn off until it warms the building at least 2°. The same is true if the temperature goes above the High Limit however, there are three levels of cooling stages on the Back-Up System. The following example explains the operation of the stages in relationship to the temperature and the limits. In this example the Low Limit is set as 66º F, and the High Limit is set as 86º F. If the temperature drops to 66º F, then the HEAT stage turns on. The HEAT stage turns off when the temperature rises to 68º F (2º above the Low Limit). If the temperature rises to 86º F, then COOL 1 turns on. If the temperature continues to rise to 87º F (1º above the High Limit), then COOL 2 turns on. If the temperature rises to 89º F, then COOL 3 turns on. When used with EV-3000/3001, Cool 3 comes ON and Cool 1 will go OFF to disable sidewall/negative fans while in tunnel ventilation. Stages turn off at temperatures as indicated by the arrows in Graph 1. Graph 1: Cool 1, 2, 3 and Heat Temperature (°F) Heat Cool 3 - Tunnel Cool 2 Cool 1 - Vents

Secondary Sensing System 20 of 42 SPECIAL FEATURES IF CONNECTED TO EVOLUTION 3000/3001 7.1.2 Emergency Operation In this mode of operation, the system still maintains the temperature as it does in Normal Operation. In addition, it will begin running the first cooling stage (Cool 1) on a 5 minute timer. The timer percentage is determined by the setting in P3 (Emergency Timer Percentage). This mode of operation is entered if communication is lost between the master controller and the S3. In this case, the S3 assumes that the master controller is lost and tries to maintain the minimum ventilation until someone recognizes the problem. Emergency Operation is indicated by a “LnE” flashing in the display of the S3. The alarm relay on the S3 is also engaged in this mode operation. 7.1.3 Override Operation In this mode of operation, the system still maintains the temperature as it does in Normal Operation. In addition, it receives commands from the master controller to turn on certain stages of heating or cooling. There are many different circumstances that could cause this to happen, in this manual, we will list one of the most common. For example, if communication were lost inside the EV-3000, the master controller would be unable to turn the appropriate stages on in the usual way. Therefore, the master controller would communicate to the S3 and indicate which stages that it is trying to turn on. At this point, the S3 would obey the command and turn the appropriate stages on. For this mode of operation to work to its fullest potential, care must be taken to insure that the stage jumpers on the relay strips match the stage setting in the master controller (Refer to Section 11.6). Override Operation is indicated by a “LnO” flashing in the display of the Back-Up System. The alarm relay is also engaged in this mode of operation. “LnE” flashing in the Display “Ln0” flashing in the Display

Secondary Sensing System 21 of 42 SPECIAL FEATURES IF CONNECTED TO EVOLUTION 3000/3001 7.1.4 Fail-Safe Relay Operation There are two types of Relay strips used in the Evolution 3000. The Normally Open (NO) strip requires a signal from the controller board in order to energize a stage of ventilation. Should power be removed from the EV-3000 the Normally Open Relay strips would not be able to energize a ventilator. On the other hand the Fail-Safe relay strip would close each of the relays in the strip resulting in energizing the ventilators in case of a controller power failure. Each of the relay strips contains four relays for controlling four stages. In the EV-3000 there are a total of four relay strips, three will be N.O. and one will be a Fail-Safe. The operator must insure that the Fail Safe relay strip is connected only to stages that should be turned on in case of a controller failure. See the EV-3000 Owners Manual Part No. 4801-5307 for a physical description of the relay strips. The S3 Stand-Alone Unit (Plus) also contains a Fail-Safe. It is not recommended to place heating equipment on Fail-Safe stages. 7.1.5 Setting EV Back-Up Stage Jumpers Pictured at the right is a Stage Relay Board consisting of four stage relays and the associated stage jumper for each stage relay. This board is located in the EV-3000 or EV-3001 controller. The stage jumpers are labeled COOL 1, COOL 2, COOL 3 and HEAT. Location of the jumper places the equipment on one of these four Back-Up Stages, or if the jumper is not inserted, the equipment is not placed on Back-Up. The jumpers should be placed based on the operation of stage equipment and should be the same as assigned in the EV-3000 Controller. Jumpers are placed according the following table: Type of Stage Operation Jumper Assignment Cool Negative Fan COOL 1 Cool Negative Tunnel Fan COOL 2 Cool Tunnel Fan COOL 3 Heat Stage HEAT Stage not on Back-Up No Jumper Installed Additional information can be found in the Evolution 3000 Owners Manual, Part Number 4801-5307. 7.1.6 Vent/Tunnel Inlet Override Operation The S3 contains override relays to operate your Vent or Tunnel inlets during Back-Up situations. It is intelligent enough to understand how it needs to operate these overrides in a manner that will not disrupt what the main control system is trying to do. Typical operation results in the Tunnel inlet being overridden open anytime the Back-Up stage Cool3 is on. Otherwise, if Cool1 or Cool2 is on, the S3 will override the Vent inlets open. This is the correct assumption most of the time but there are exceptions. It is important to note that if Cool3 is turned on, the S3 will turn off Cool1 which, in turn, will disable the Vent inlet override. This allows the Back-Up system to perform in much that same manner as the main control system would function during tunnel ventilation. If connected to the Evolution 3000/3001, the S3 communicates with the master controller. Therefore, it is aware of what type ventilation mode the controller is currently in. For example, if the main controller is in tunnel ventilation. The S3 will not allow Cool1 to turn on. The reason is due to the fact that it knows that this is your sidewall fans. Therefore, it understands that it would be detrimental to the ventilation to turn them on. This, in turn, also disables the Vent inlets from opening. STAGE RELAY BOARD Stage Relay COOL 3 COOL 2 COOL 1 HEAT Stage Jumpers

Secondary Sensing System 22 of 42 7.2 Operation as Stand-Alone System The S3 contains an integrated back-up system. This system’s purpose is to back up the master controller in the case of failure. The back-up system is a stand-alone control system. It contains its own three temperature sensors which are used to divide the building into zones. These are the same temperature sensors that are used for the alarming functions described earlier. This allows the user to set High and Low Back-Up limits, in which the system will use to operate one Heat stage and three Cool stages. The system is equipped with a fail-safe relay card that is capable of driving four separate 1 h.p. loads. The following shows the Back-Up System interface. This setup does not use the Local Network connection that would be present if used in conjunction with the Evolution 3000/3001. Therefore, its functionality is limited to monitoring the temperature sensors for out of range conditions but it does still contain some protection against minimum ventilation failure. 7.2.1 Normal S3 Back-Up Operation During Normal Operation, the S3 always maintains the temperature between its high and low limits. It accomplishes this by using its temperature sensors and its four stage outputs. If the temperature drops below the Low Limit, the Heat stage will come on. That stage will not turn off until it warms the building at least 2°. The same is true if the temperature goes above the High Limit however, there are three levels of cooling stages on the Back-Up System. The following example explains the operation of the stages in relationship to the temperature and the limits. In this example the Low Limit is set as 66º F, and the High Limit is set as 86º F. If the temperature drops to 66º F, then the HEAT stage turns on. The HEAT stage turns off when the temperature rises to 68º F (2º above the Low Limit). If the temperature rises to 86º F, then COOL 1 turns on. If the temperature continues to rise to 87º F (1º above the High Limit), then COOL 2 turns on. If the temperature rises to 89º F, then COOL 3 turns on. Stages turn off at temperatures as indicated by the arrows in Graph 1. Graph 1: Cool 1, 2, 3 and Heat Temperature (°F) Heat Cool 3 - Tunnel Cool 2 Cool 1 - Vents Temperature/Settings Display Selection Switch Back-Up Stages Indicators Ventilation Back-Up Display & Selector Inlet Overrides Indicators

Secondary Sensing System 23 of 42 7.2.2 Minimum Ventilation Protection As explained earlier, this Back-Up System contains a back-up minimum ventilation timer. This timer is normally off but is triggered upon an alarm occurring on the Control System auxiliary input. There are two situations that can cause an alarm on the Control System auxiliary that depends on the setting in P62 (See Section 6.3). Whether P62 is set to be a Cycle Pressure Alarm or a normal control system alarm, if the alarm is triggered the S3 will enable the 5 minute timer clock. Then Cool1 will operate based on the setting in P3. This process will continue as long as the Control System auxiliary alarm is present. 7.2.3 Fail-Safe Relay Strip The stand-alone system will be equipped with a fail- safe relay strip. This relay strip has four output relays. Each relay is capable of driving up to 1 h.p. Also, each relay has a stage jumper. These stage jumpers can be used to assign each relay to a back- up stage, Heat, Cool1, Cool2, Cool3. Therefore, the end user can select what stages that he would like to back up. For example, you may not care to back up your heat stages; therefore, you could use one relay for Cool1, one relay for Cool2, and two relays for Cool3. Any combination will be acceptable but it is important that you understand the operation of each output so that you back up your main control system appropriately. For example, minimum ventilation protection is provided by Cool1. If you do not assign a relay output to Cool1, you will not have back up protection for minimum ventilation. It is also important to choose the correct fans to back up. For example, choose a fan that is not your typical minimum ventilation fan to run off of Cool1, such as one of your initial tunnel fans. This will help you two ways. First, it will protect against fan mechanical failure. Secondly, by choosing a tunnel fan it will not affect tunnel ventilation if the back up kicks in on a hot day. The graph in Section 7.2.1 helps to show how the stages operate but it is also important to understand how the inlet overrides operate in conjunction with the Cool outputs (See Section 7.2.4). The following table helps associate the Back-Up stage outputs with the type of equipment that you are trying to operate. Type of Stage Operation Jumper Assignment Cool Negative Tunnel Fan COOL 1 * Cool Negative Tunnel Fan COOL 2 Cool Tunnel Fan/Evap. COOL 3 Heat Stage HEAT Stage not on Back-Up No Jumper Installed * IMPORTANT NOTE: Cool1 controls your minimum ventilation Back-Up Stage. 7.2.4 Vent/Tunnel Inlet Override Operation The S3 contains override relays to operate your Vent or Tunnel inlets during Back-Up situations. It is intelligent enough to understand how it needs to operate these overrides in a manner that will not disrupt what the main control system is trying to do. Typical operation results in the Tunnel inlet being overridden open anytime the Back-Up stage Cool3 is on. Otherwise, if Cool1 or Cool2 is on, the S3 will override the Vent inlets open. This is the correct assumption most of the time but there are exceptions. STAGE RELAY BOARD Stage Relay COOL 3 COOL 2 COOL 1 HEAT Stage Jumpers

Secondary Sensing System 24 of 42 The exception occurs if the S3 determines that conditions warrant tunnel ventilation. Therefore, it assumes that opening the Vent inlets would be detrimental to the current ventilation setup. In this case, it will open the Tunnel inlet upon any Back-Up stage being turned on due to temperature. It is important to note. If the Back-Up stage Cool1 is ever timed on due to detection of a minimum ventilation error, then it will always override the Vent inlets only. 8. Trouble-Shooting Your Alarm 8.1 Low Battery If the battery in the S3 drains down to approximately 10.6 volts, the Low Battery alarm condition will be active. This is very common if the alarm has sounded for some time. If the Low Battery alarm is active, the Alarm should be set so that no alarm condition exists and the battery should be allowed to recharge. This may require the operator to disconnect the siren to allow the battery to build back up. If recharging doesn’t fix the problem, then the battery must be replaced. Contact your nearest Cumberland dealer for a replacement. 8.2 Power Out The Power Out alarm can occur in two cases. One is when the power has been out for more than one minute. The other situation could be caused by the 120VAC 3 amp fuse blown. If the Power-Out alarm condition is active and you find that there is power present at the outlet where the alarm is plugged in, then you should check the fuses. 8.3 No Siren at Test If the siren fails to sound when the test button is pressed, several conditions could exist. The siren itself could be bad. Check for 12VDC at the siren leads. And, of course, there could be a bad connection somewhere in the siren circuit. 8.4 Replacing the Fuses The S3 includes two fuses located on the circuit board; One AC power fuse (F1 - 3 Amp) and also a Back- Up Relay circuit fuse (F2 - 3 Amp). AC Power Fuse (F1, 3 Amp Slow-Blow) The AC Power Fuse is electrically placed between the S3 operating circuitry and the 4-pin header connector connected by wires to the AC conversion transformer. If power is present at the AC wall receptacle and the S3 front panel displays are not ON, check the AC Power Fuse for a blown fuse. Back-Up Relay Fuse (F2, 3 Amp Slow-Blow) The Back-Up Relay Fuse helps to provide protection between the S3 circuitry and the EV-3000/3001. If all AC power is turned OFF or unplugged at the electrical outlet AND the externally powered controls are also lacking power, the 3 Amp slow-blow fuse located on the S3 circuit board (Fuse F2) should be checked for a blown fuse.

Secondary Sensing System 25 of 42 Fuse Replacement To replace either fuse, disconnect AC power, disconnect the positive (+) battery terminal from the battery, and carefully replace the blown fuse with the correctly sized replacement fuse. Reconnect the positive (+) battery terminal to the battery, plug the male plug end of the AC power cord to the electrical outlet, and verify that power and functional operation has been restored. AC Power Fuse Back-Up Relay Fuse 8.5 Temperature Sensors Disconnected If the temperature Sensors become disconnected or damaged, the Display Indicator for that sensor will show a line of bars (- - -). This problem should be corrected before any attempt to calibrate the sensor is made. 8.6 Temperature Sensors Out of Calibration If the operator believes that the temperature sensors are not reading correctly, the following steps should be followed: Obtain a thermometer that is known to be accurate. Place this thermometer next to the temperature sensor for at least 10 minutes. Insure that there are no strong breezes or winds blowing on the thermometer and the sensor being calibrated. Note the temperature from the thermometer and use this reading to calibrate the sensor. Refer to Section 9.3 for Sensor Recommendations. 8.7 Trouble-Shooting the Auxiliaries The auxiliary inputs must always form a closed loop circuit. If the loop is ever open, the alarm will sound. If an auxiliary input is sounding, the trouble can be isolated between the alarm and the circuit by disconnecting the circuit from the terminal block in the alarm box and replacing it with a jumper (See Section11.8). If the corresponding auxiliary input still causes an alarm condition, the problem is in the PCB circuitry, otherwise the wiring is the culprit. 9. Controller Installation and Setup 9.1 Tools Required Mini Screwdriver Standard Screwdriver Wire Strippers 9.2 Installation Instructions 1. Unpack system, and check that all components are present. Qty Description Qty 1 Description S3 1 Local Net Cable 3 Temperature Sensors 1 Back-Up Cable 1 Manual

Secondary Sensing System 26 of 42 2. Hang S3 with four screws. 3. Make sure all power supplies are disconnected before breaking any wires, or reaching into the system enclosure. 4. Open the S3 and find all connections. Refer to wiring diagrams in Section 11 of this manual. 5. Run temperature sensors out to locations inside the house. Be sure that the sensors are in a safe location, free from any temperature influences (direct sunlight, water, etc.) Use care when securing sensor wires so that the wire is not accidentally cut. Any short, or break in the wire will cause improper sensor operation. Next, run the wires into the enclosure via the watertight connector at the bottom of the box. The wires should be cut off and stripped. They next should be attached to the terminal block in the positions marked Sen 1, Sen 2 and Sen 3. Note that the sensors are not polarity sensitive, and it therefore makes no difference as to which wire goes to which sensor terminal. 6. After the siren is mounted, it should be wired into the control box. This is done at the terminal block locations labeled siren red and siren white. Note that polarity is important here and that the red siren wire must be connected into the siren red terminal block position and the same for the white wire. Note also, any 12VDC device that uses less than 1.5 Amps of current could be connected in the siren’s place. 7. Connect wires from Alarm terminals to the alarm circuit or relay box. (See wiring diagrams in Section 11.7 for locations of terminals.) 8. If using a modem, connect wires from Modem terminals to the modem circuit or relay box. (See wiring diagrams in Section 11.7 for locations of terminals.) 9. If necessary, connect the S3 to the Cumberland Farm Manager Network. (See the connections in Section 11.10 of this manual.) 10. Connect the AUX and CONTROL AUX connections. Refer to Section 11.8 diagram. 11. Remove jumpers for AUX & CONTROL connections if being used. 12. If connecting to an EV 3000/3001 controller, connect Local Net and Back-Up Network setting in Evolution controller (Plus models ONLY). 13. Wire Stage to Relay Card for Back-Up operation. 14. Set Stage Jumpers on Relay Cards in S3 or EV 3000/3001. Refer to Section 11.6 diagram. 15. Connect Vent/Tunnel Overrides. 16. Connect AC Power. Refer to Section 11.3 diagram. 17. Program the S3. Refer to Section 5. 9.3 Sensor Recommendations It is important to note the Cumberland temperature sensors are fabricated using thermistors and are not interchangeable with sensors commonly used on controllers from other manufacturers. The three temperature sensors may be installed in a variety of ways. It is recommended that a sensor be located high enough from the floor so that livestock or poultry can not peck at it. It is also essential that the sensor not be hung in front of heaters, fans or other devices that would cause false readings. If a sensor is to be run from one building to another, it is recommended that the connection be made with underground-rated wire buried between the two structures. This recommendation is to reduce the effects of lightning. Once again, the temperature sensors should be dropped as low in the house as possible while still being out of reach of the livestock or poultry. And, as discussed earlier, it is recommended that the operator press the Test button for ten to fifteen seconds at least twice a week to verify the operation of the alarm as well as to condition the livestock or poultry to the sound of the siren.

Secondary Sensing System 27 of 42 10. Maintenance Check the calibration of your temperature sensors at least once per quarter. You will need to have two people, one at the sensor with a trusted thermometer, and one at the controller to calibrate the sensor. 11. Wiring Diagrams, Schematics, etc. The following diagrams the S3 circuit board connections and how the S3 is connected to external equipment. 11.1 S3 Internal Electrical Wiring

Secondary Sensing System 29 of 42 11.3 Connecting AC Power to the S3 Secondary Sensing System Inset A Inset A

Secondary Sensing System 30 of 42 11.4 Connecting Sensors to the S3 White/ Shield Sen 3 Black Black Sen 2 White/ Shield White/ Shield Sen 1 Black Inset A SENSOR SENSOR SENSOR White / Shield White / Shield White / Shield Black Black Black Inset A Secondary Sensing System

Secondary Sensing System 31 of 42 11.5 S3 PowerTrak Override Settings and Wiring PowerTrak Inset A Vent Override for Fail-Safe Action INLET MODE Vent Override Cool 1 Tunnel Override Cool 3 Vents & Tunnel Will Wire The Same NOTE: If curtain is setup to pull curtain up to open, then reverse wires connected to 'Open' and 'Close' terminals. Inset B Tunnel Override Inset A Vents Override PowerTrak Inset B PowerTrak Inset B Inset A Vent Override for Normal Action Refer to Section 5.1 P5 & P6 Settings Secondary Sensing System

Secondary Sensing System 32 of 42 11.6 S3 Relay Card Wiring Secondary Sensing System Inset A Relay Card Relay Card Wire Terminals NOTE: Ensure the Relay Card connector and the PCB header are properly aligned during stand-off and Relay Card installation. NOTE: The Relay Card is necessary on Stand-Alone systems ONLY. If S3 is used in conjunction with Evolution 3000/3001, this relay card is optional. Header Connection For Relay Card Six Stand-Off Attachment Holes Inset A Relay Card

Secondary Sensing System 33 of 42 11.7 Connecting an Alarm or Siren to the S3 Inset A White Red NO NC Com Alarm Out Siren Internal Switch (Non-alarm) position Connect to alarm, modem, auto- dialer,etc. as desired. White (-) Red (+12V) Siren Inset A Secondary Sensing System

Secondary Sensing System 34 of 42 11.8 Connecting Auxiliary Inputs to the S3 Inset B Inset A NOTE: The jumper across J6, J8 and\or J10 must be removed if an external alarm input is connected. Secondary Sensing System

Secondary Sensing System 35 of 42 11.9 Connecting Other Cumberland Controllers to the S3 Auxiliary Input The diagram below shows the proper way to connect the Cumberland family of auxiliary alarm outputs to the S3 auxiliary inputs. The alarm activates when the connection is broken between the OUT and IN terminals. NOTE 1: As long as a path for current flow is present, the Secondary Sensing System is not activated. Consequently, if one controller alarms, the path will be broken and the alarm will be activated. NOTE 2: Remove the jumper between the OUT and IN terminals when installing external alarm inputs.

Secondary Sensing System 36 of 42 11.10 Connecting Local Network Connections to the S3 Warning! Tape Shield To Prevent Damage! NOTE: Harness to connect Local Network and Secondary Sensing system together are connected & included in the Secondary Sensing System and 16 Stage Expansion units. Back-Up System

Secondary Sensing System 37 of 42 11.11 Connecting the S3 to the HH.Net Inset B Inset A Secondary Sensing System

Secondary Sensing System 38 of 42 12. Replacement and Optional Parts Controls 6450-5089 /KIT FH-AL to S3 upgrade 6607-8013 EV S3 Plus 6607-8014 EV S3 Replacement Parts 6407-0616 /DOOR ASSY S3 6407-6038 /EV-S3 Stand Alone Relay Card (PCB161) 3014-2174 Battery 12V 5.0 Ah 3006-3115 CONN SKT CLIP (For Tunnel/Vent Relays) 3006-5077 CONN Terminal Block 3 pos 3006-5078 CONN Terminal Block 4 pos 3006-5079 CONN Terminal Block 5 pos 3006-5092 CONN Terminal Block 6 pos 3540-0149 DIGITAL_IC LTC1483CN8 (Network Chips) 3010-2991 FUSE 3 AMP 5mmX20mm slowblow (F1 & F2) 3701-6066 PIC S3 (Processor) 3015-1560 RLY AZ755-1C-12DE (Relay For Tunnel/Vent) 3008-2860 XFMR FD7-16 120/240-16VAC 56VA (Transformer) Sensors and Wire 1503-2427 CBL SJT 18-2 Yellow (sensor) 6407-6084 /Temperature Sensor Junction Box Assy Siren/Dialer 3016-1380 SIREN 12 VDC 1 AMP cont/warb 6607-6000 Voice Dialer AVD-45B Manuals 4801-2997 MANUAL S3 4801-5307 MANUAL Evolution 3000\3001 4801-5331 MANUAL Evolution 1200

Secondary Sensing System 39 of 42 13. Temperature vs. Sensor Resistance Table The following chart gives the resistance when measured between the white and black sensor wires at a given temperature. To check a sensor, first know the temperature in the area, then, use a multi-meter to check the resistance. Resistance Temp Temp Resistance Temp Temp Resistance Temp Temp Kohms (F) (C) Kohms (F) (C) Kohms (F) (C) 32.654 32 0 15.714 59 15 8.59 83.3 28.5 32.158 32.5 0.3 15.568 59.4 15.2 8.517 83.7 28.7 31.671 33.1 0.6 15.353 59.9 15.5 8.408 84 28.9 31.191 33.6 0.9 15.211 60.3 15.7 8.336 84.6 29.2 30.72 34.2 1.2 15.001 60.8 16 8.23 85.1 29.5 30.257 34.7 1.5 14.863 61.2 16.2 8.125 85.6 29.8 29.802 35.2 1.8 14.658 61.7 16.5 8.056 86 30 29.355 35.8 2.1 14.457 62.2 16.8 7.954 86.5 30.3 28.915 36.3 2.4 14.325 62.6 17 7.853 87.1 30.6 28.482 36.9 2.7 14.128 63.1 17.3 7.787 87.4 30.8 28.057 37.4 3 13.999 63.5 17.5 7.689 88 31.1 27.777 37.8 3.2 13.808 64 17.8 7.592 88.5 31.4 27.363 38.3 3.5 13.682 64.4 18 7.496 89.1 31.7 26.957 38.8 3.8 13.496 64.9 18.3 7.433 89.4 31.9 26.557 39.4 4.1 13.373 65.3 18.5 7.34 90 32.2 26.164 39.9 4.4 13.192 65.8 18.8 7.248 90.5 32.5 25.777 40.5 4.7 13.073 66.2 19 7.157 91 32.8 25.523 40.8 4.9 12.896 66.7 19.3 7.098 91.4 33 25.147 41.4 5.2 12.779 67.1 19.5 7.009 91.9 33.3 24.777 41.9 5.5 12.607 67.6 19.8 6.922 92.5 33.6 24.413 42.4 5.8 12.493 68 20 6.836 93 33.9 24.055 43 6.1 12.325 68.5 20.3 6.779 93.4 34.1 23.82 43.3 6.3 12.215 68.9 20.5 6.695 93.9 34.4 23.472 43.9 6.6 12.051 69.4 20.8 6.612 94.5 34.7 23.13 44.4 6.9 11.943 69.8 21 6.531 95 35 22.793 45 7.2 11.783 70.3 21.3 6.45 95.5 35.3 22.572 45.3 7.4 11.678 70.7 21.5 6.371 96.1 35.6 22.244 45.9 7.7 11.522 71.2 21.8 6.319 96.4 35.8 21.922 46.4 8 11.42 71.6 22 6.241 97 36.1 21.71 46.8 8.2 11.268 72.1 22.3 6.165 97.5 36.4 21.397 47.3 8.5 11.168 72.5 22.5 6.089 98.1 36.7 21.088 47.8 8.8 11.02 73 22.8 6.015 98.6 37 20.886 48.2 9 10.874 73.6 23.1 5.941 99.1 37.3 20.586 48.7 9.3 10.778 73.9 23.3 5.869 99.7 37.6 20.29 49.3 9.6 10.636 74.5 23.6 5.798 100.2 37.9 20.096 49.6 9.8 10.542 74.8 23.8 5.728 100.8 38.2 19.809 50.2 10.1 10.404 75.4 24.1 5.658 101.3 38.5 19.526 50.7 10.4 10.312 75.7 24.3 5.59 101.8 38.8 19.34 51.1 10.6 10.177 76.3 24.6 5.522 102.4 39.1 19.065 51.6 10.9 10.088 76.6 24.8 5.456 102.9 39.4 18.884 52 11.1 9.956 77.2 25.1 5.39 103.4 39.7 18.616 52.5 11.4 9.869 77.5 25.3 5.326 104 40 18.352 53.1 11.7 9.741 78.1 25.6 5.262 104.5 40.3 18.179 53.4 11.9 9.614 78.6 25.9 5.199 105.1 40.6 17.503 54.9 12.7 9.53 79 26.1 5.137 105.6 40.9 17.339 55.2 12.9 9.407 79.5 26.4 5.076 106.2 41.2 17.095 55.8 13.2 9.325 79.9 26.6 4.995 106.9 41.6 16.856 56.3 13.5 9.205 80.4 26.9 4.936 107.4 41.9 16.698 56.7 13.7 9.086 81 27.2 4.877 108 42.2 16.465 57.2 14 9.007 81.3 27.4 4.82 108.5 42.5 16.312 57.6 14.2 8.891 81.9 27.7 4.763 109 42.8 16.085 58.1 14.5 8.815 82.2 27.9 4.688 109.8 43.2 15.935 58.5 14.7 8.702 82.8 28.2

Secondary Sensing System 40 of 42 14. Error Codes The controller records errors based on the communications links. When errors occur, an alarm will be generated. Error Codes for the Evolution S3 Error Code Description Explanation LnE Local Network Error The Back-Up has lost Communications with the Master Controller. NOTE: During this condition the Back-Up will run Cool 1 on a 5 minute timer. LnO Local Network Override Error The Master Controller has lost communications with one or more of the Stage Units (PCB 168) connected to it. In this condition the Back-Up takes control over the stages. 15. S3 Program Label

Secondary Sensing System 41 of 42 Limited Warranty 16. Warranty The GSI Group, LLC. (“GSI”) warrants products which it manufactures to be free of defects in materials and workmanship under normal usage and conditions for a period of 12 months after sale to the original end- user or if a foreign sale, 14 months from arrival at port of discharge, whichever is earlier. The end-user’s sole remedy (and GSI’s only obligation) is to repair or replace, at GSI’s option and expense, products that in GSI’s judgment, contain a material defect in materials or workmanship. Expenses incurred by or on behalf of the end-user without prior written authorization from the GSI Warranty Group shall be the sole responsibility of the end-user. Warranty Extensions: The Limited Warranty period is extended for the following products: Product Warranty Period AP Fans and Flooring Performer Series Direct Drive Fan Motor 3 Years All Fiberglass Housings Lifetime All Fiberglass Propellers Lifetime AP/Cumberland Flex-Flo/Pan Feeding Systems 2 Years Cumberland Feeding/Watering Systems Feeder System Pan Assemblies 5 Years ** Feed Tubes (1.75" & 2.00") 10 Years * Centerless Augers 10 Years * Watering Nipples 10 Years * Grain Systems Grain Bin Structural Design 5 Years Grain Systems Farm Fans Zimmerman Portable & Tower Dryers 2 Years Portable & Tower Dryer Frames and Internal Infrastructure † 5 Years GSI further warrants that the frame, basket and excluding all auger and auger drive components of the portable and tower dyer shall be free from defects in materials for a period of time beginning on the twelth (12th) month from the date of purchase and continuing until the sixtieth (60th) month from the date of purchase (extended warranty period). During the extended warranty period, GSI will replace the frame or basket components that prove to be defective under normal conditions of use without charge, excluding the labor, transportation, and/or shipping costs incurred in the performance of this extended warranty. Conditions and Limitations: THERE ARE NO WARRANTIES THAT EXTEND BEYOND THE LIMITED WARRANTY DESCRIPTION SET FORTH ABOVE. SPECIFICALLY, GSI MAKES NO FURTHER WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR USE IN CONNECTION WITH: (i) PRODUCT MANUFACTURED OR SOLD BY GSI OR (ii) ANY ADVICE, INSTRUCTION, RECOMMENDATION OR SUGGESTION PROVIDED BY AN AGENT, REPRESENTATIVE OR EMPLOYEE OF GSI REGARDING OR RELATED TO THE CONFIGURATION, INSTALLATION, LAYOUT, SUITABILITY FOR A PARTICULAR PURPOSE, OR DESIGN OF SUCH PRODUCTS. GSI shall not be liable for any direct, indirect, incidental or consequential damages, including, without limitation, loss of anticipated profits or benefits. The sole and exclusive remedy is set forth in the Limited Warranty, which shall not exceed the amount paid for the product purchased. This warranty is not transferable and applies only to the original end-user. GSI shall have no obligation or responsibility for any representations or warranties made by or on behalf of any dealer, agent or distributor. GSI assumes no responsibility for claims resulting from construction defects or unauthorized modifications to products which it manufactured. Modifications to products not specifically delineated in the manual accompanying the equipment at initial sale will void the Limited Warranty. This Limited Warranty shall not extend to products or parts which have been damaged by negligent use, misuse, alteration, accident or which have been improperly/inadequately maintained. This Limited Warranty extends solely to products manufactured by GSI. Prior to installation, the end-user has the responsibility to comply with federal, state and local codes which apply to the location and installation of products manufactured or sold by GSI. * Warranty prorated from list price: 0 to 3 years – no cost to end-user 3 to 5 years – end-user pays 25% 5 to 7 years – end-user pays 50% 7 to 10 years – end user pays 75% ** Warranty prorated from list price: 0 to 3 years – no cost to end-user 3 to 5 years – end-user pays 50% † Motors, burner components and moving parts not included. Portable Dryer screens included. Tower Dryer screens not included.