DOM 510 Manual Instruction

Seat pad x1 Frame supporter x3 Flag & Horn toy bar x1 Front wheels x2 Base section x1 Pushing bar x1 Mirror x2 Toy tray x1 rear car wheels x2 front car wheels x2 Lollipop ball & Cresset toy bar x1 Rear wheels x2 Decoration sticker 1 and 2, Pls. refer to the detailed instruciton about on manual how to put these sticers on walker .

1.Turn one side of frame supporter outward (1) until you hear the frame supporter lock into position (2). To attach top tray car wheels 2. Attach the front wheels to the side of the top tray. Press inward the wheels until hear “click”. jpg (1) Insert the rear wheels into the groove under the walker tray up. jpg (2) Press the wheels until hear “click”. jpg (3) To assemble and install the frame supporters into top section 3.Place the top section upside down on the floor. Slot the top of the frame supporters onto the holes. Using moderate force, push the frame supporter in the top section. Ensure that the supporters are fully inserted before proceeding. To attach the wheels 4.Insert the wheels into the moulded socket in the direction indicated by the arrow. Then push firmly until clicks into place. To assemble top and base section 5.Place the base section on the floor, slot the end of frame supporters into the holes indicated in the drawing (1). Press the button in and push the frame supporters downward to adjust the height to your wish position. 3 positions optionale. See jpg (2) jpg (3).

6.Insert the mirrors into the circular buttonholes on the upper tray as the arrow indicated. (Pay attention to the left and right directions when installing) Eusure the mirrors can 360° rotate in two directions. To attach the flag and horn toy bar 7.Position the flag and horn toy bar over the slots in the front up tray and turn them in a clockwise direction until they lock into place. See fig.1 and fig.2 To attach the lollipop toy bar and cresset ball 8. Position the lollipop toy bar and cresset ball over the slots in the rear up tray and turn them in a clockwise direction until they lock into place. See below fig. To attach the toy tray 9.2XAA size alkaline batteries are needed for the toy tray (not included). Put the batteries into the battery box under the toy tray base. Place the toy tray into position. Pushing the locking keys located on the underside of the walker tray up and turn around to secure the toy tray to the walker. Fitting the seat pad 10. Position the seat pad into the top section. Using moderate force push downwards until it locks in the top section.

13.The button”a”is on the right side which can lock the frame supporters not to jump when using as baby walker.Push the button”a”to the left side to release the frame supporters. Then baby walker can change to jumper walker. Please make sure that the jump function must be locked when use as baby walker. Jumper walker 1 2 (1)When the product is being used as an Activity Centre, all the wheels on the base must be removed as Stationary status （pic 2）. (2)Press button “1” and pull the lever “2” outwards to unlock the seat (pic1). (3)While using the product as an activity center, rolate the rear plate outward and keep its position same as pic2, and the jump function should be released or locked during the activity center. Locking the swivel seat when use as baby walker 12.(1) Rotate the seat so that it is facing the front part of the walker (pic1).(2) Press button “1” on the rotation locking device,located under the top, and push the locking lever “2” inwards (pic1). Make sure that the lever is locked properly in the appropriate slot. A click will indicate that it is attached correctly. Unlocking the swivel seat when us as activity center. Pic1 Pic2 How to put decoration stickers on product NOTICE: In your product packaging there includes some decoration stickers which is a free gift for you. If you like them, pls. follow the instructions on the stickers to stick them on your walker. On the stickers it showes the location on the walker for each sticker . If you don't want these stickers, you can throw them away, 11. Please stick the sticker to the postion with same number code. Please make sure there is no dirty like water,sweat stain,etc. on the surface of plastic parts.

1 .Detach the toy bar. Position the hand rail over the slots in the rear up tray. Attach the locking cover to end of toy bar and turn around to secure the hand rail to the walker. walk-behind 1 . Turn the rear plate inward in 180 degree. b a To store the baby walker 1 .Pull forward of safety pin ‘a‛ at left side of each frame supporters fig (2) and press button ‘b‛ at right side of each frame supporters, then forward the frame supporters to the centre of baby walker. Make sure all three frame supporters are forwarded to the centre of baby walker. To open the baby walker 1 .Lift the top section upwards, pull the end of frame supporters outside until three frame supporters stand fig (2) fig (3). , or activity center Caution position

assembly may make the product unsafe.Do not use the product if any part is broken,torn or missing. Keep these instructions in a safe place for future reference . n used that ntended to be of the baby's face and mouth.

for extended periods of time. • Removable fabric covers and trims must only be cleaned using warm water with a household soap or mild detergent. Allow it to dry fully, preferably away from direct sunlight. grip pads regularly, using warm water with household soap or mild detergent to maintain stopping performance . • Do not fold or store the product if it is damp or wet to avoid mold or mildew occurring.Always store the product in a well ventilated area. • parts regularly for tightness of screws, nuts and other fasteners, tighten if required.To maintain the safety of your nursery product, seek prompt repairs for bent,torn,worn or broken parts.Use only parts and accessories approved by Dream On Me. • If the wheels squeak use a silicon based spray ensuring it penetrates the wheel and axle assembly. Care and maintenance Do not mix old and new batteries . Do not mix alkaline, standard (carban·zlnc) or rechargeable lnickle-cadm. Do not charge non-rechargeable balleries. Adult supervision is required when charging rechargeable battenes , Always remove flat or exhausted batteries from the toy . Do not short circuit the supply terminals. Recommended batteries, 2X 1.5V, ‘AA’ / SUM3 / LR6. BATTERY INFORMATION: DO NOT place items with a string around child’s neck, such as hood strings or pacifier cords. DO NOT suspend strings over product or attach strings to toys. Always keep child in view while in product. While using as a activity center, it should be used by a child who can sit unaided(approximately from 6 months).It should be not used by a child who weighing more than 12kgs. WARNING: Never use near stair. To avoid tip over, place product on a flat, level surface. • • WARNING: