Geoline GeoSystem 200 Operator's Manual

- 1 ENGLISH 1 INDEX 1 INDEX ___________________________________________________________________________ 1 2 INTRODUCTION ___________________________________________________________________ 2 3 LEGEND _________________________________________________________________________ 3 4 INTENDED USE ___________________________________________________________________ 3 5 WARNING ________________________________________________________________________ 4 6 PACKAGE CONTENT ______________________________________________________________ 5 7 DIMENSIONS _____________________________________________________________________ 5 8 ACCESSORIES ___________________________________________________________________ 6 9 TECHNICAL DATA _________________________________________________________________ 7 10  INSTALLATION OF COMPONENTS ___________________________________________________ 8 10.1 CONFIGURATIONS ___________________________________________________________ 8 10.2 CONNECTIONS SCHEME _____________________________________________________ 10 10.3 COMPUTER INSTALLATION __________________________________________________ 13 10.4 SPEED SENSOR INSTALLATION _______________________________________________ 13 10.5 FLOWMETER INSTALLATION _________________________________________________ 14 10.6 CHECK HARDWARE INSTALLATION ___________________________________________ 14 11  INTERFACE DESCRIPTION OF INDICATOR ___________________________________________ 15 11.1 TABLE LIST OF BUTTONS AND THEIR FUNCTIONS _______________________________ 15 11.2 MENU STRUCTURE __________________________________________________________ 16 11.3 CONFIGURATION GENERAL PARAMETERS _____________________________________ 17 11.3.1 LIST OF MENU ITEMS OF GENERAL CONFIGURATION ________________________ 18 11.5 CALIBRATION MENU ________________________________________________________ 25 11.6 VALUE OF SOFTWARE PARAMETERS __________________________________________ 30 12  HW TEST _______________________________________________________________________ 31 13  USE OF GEOSYSTEM 200 __________________________________________________________ 33 13.1 DISPLAY – EXAMPLE OF VISUALIZATION WITH 4 SENSORS _______________________ 33 13.2 DEFINITION OF TANK REPLENISHMENT ________________________________________ 33 13.3 DEFINITION OF TREATMENT __________________________________________________ 35 13.4 NEW TREATMENT ___________________________________________________________ 35 13.5 TURNING ON GeoSystem 200 _________________________________________________ 36 13.6 TURNING OFF GeoSystem 200 ________________________________________________ 37 13.7 TREATMENT _______________________________________________________________ 38 13.8 TANK REPLENISHMENT USING AN EXTERNAL PUMP ____________________________ 38 13.9 SETTING TANK “ZERO” LEVEL ________________________________________________ 40 13.10 TOTALIZERS (AVAILABLE WITH THE CONFIGURATIONS CONNECTED SENSORS OF FLOW AND SPEED) _____________________________________________________________ 41 13.11 RECALL DATA OF TREATMENTS __________________________________________ 42 14  ALARMS ________________________________________________________________________ 43

2 - 14.1 WARNING AND ALARMS _____________________________________________________ 43 14.2 LIST OF POSSIBLE ALARMS __________________________________________________ 43 15  TROUBLESHOOTING _____________________________________________________________ 44 DICHIARAZIONE DI CONFORMITA’ UE - EU DECLARATION OF CONFORMITY - EU KONFORMITÄTSERKLÄRUNG - DÉCLARATION UE DE CONFORMITÉ - DECLARACION UE DE CONFORMIDAD - EU ДЕКЛАРАЦИЯ О СООТВЕТСТВИИ ___________________________________ 45 16  GUARANTEE ____________________________________________________________________ 46 “QUICK REFERENCE” GEOSYSTEM 200 _________________________________________________ 47 DISPLAY VISUALIZATION- EXAMPLE OF INDICATOR CONNECTED WITH 4 SENSORS _____ 48 ALARMS _______________________________________________________________________ 48 2 INTRODUCTION Congratulations Dear User, You have chosen a product by GEOline electronic, a leading company in the development and production of electronic products for agriculture. For years now, the international trade repays our quality, experience, reliability and above all our technological innovation indicating an advanced and revolutionary know how. These are the pillars of our work and according to these beliefs we are at your service, providing you a simple but modern, accurate and efficient product that supports you in making your work easier for more years. This users manual intends to take you through the different performances of the weighing system in the easiest way and to show you some new functions as well. From configuration to use with several optional at your disposal up to the service of defective research and to security norms on equipments, GEOline electronic would not forget any information, sure to offer you more support and technical assistance. Now there is nothing left for us to do but wish you a work well done! The team of GEOline electronic

- 3 ENGLISH 3 LEGEND This user’s manual uses some conventional signs, in order to lead the user during the reading of important instructions and advices; these concern especially the setting of the parameters of the system and thus its correct working. Please pay attention to the following icons: It indicates further explaining and information. It highly recommends to pay attention. It indicates an operation that can be repeated many times, cyclically. It indicates the norms to respect. 4 INTENDED USE Visualization system of treatment data, designed to work on agricultural machinery for crop and orchard spraying applications. The accurate control of the operating parameters of the sprayer or orchard system increases the effectiveness and efficiency of the treatments, reducing the wastage of chemicals. !

4 - 5 WARNING The power supply must be connected directly to the battery or to a regulated feeder. The power supply must be protected with a 10A fuse. If it is not the case, GEOline electronic is not responsible for damages to the micro computer. Disconnect the power supply cable from the micro computer when the battery is undergoing recharge. If it is not the case, GEOline electronic is not responsible for damages to the micro computer. Disconnect all lines from the local plant before undertaking welding on the vehicle. If it is not the case, GEOline electronic is not responsible for damages to the micro computer. For a correct functioning, please make sure that the battery has always a higher voltage than 10, 5 Volt. This marking on the product or on its packaging illustrates that this product may not be disposed of with normal household waste. You are responsible for disposal of this equipment through a designated waste electrical and electronic equipment collection. To determine the locations for dropping off such waste electrical and electronic, contact your government office, the waste disposal organization that serves your household or the company at which you purchased the product. Before cleaning the agricultural vehicle with high pressure water jets, protect the equipment from any possible water entrance. In addition, take great care not to subject the devices, cables or any options to direct jets of water. If the equipment needs to be cleaned, use a soft, damp, lint-free cloth. Do not use sprays, solvents, abrasives, or sharp or pointed objects that could damage the indicator. ! ! ! ! ! ! ! ! !

- 5 ENGLISH 6 PACKAGE CONTENT Table 1- Package 7 DIMENSIONS Picture 1 – Dimensions of indicator 8410030 - Kit GeoSystem 200 Description Qty Indicator GeoSystem 200 1 mounting bracket 1

6 - 8 ACCESSORIES GeoSystem 200 may be equipped by these accessories: ACCESSORY DESCRIPTION Magnetic Flowmeter A sensor to noting the flow and to calculate the litres Paddle Flowmeter A sensor to noting the flow and to calculate the litres Pressure Sensor A sensor to measuring the pressure Level Sensor A sensor to measuring the liquid level in the tank Sucker hangers with mini VESA connection Hanger to fix in a glass surface Pole mounting bracket Hanger to install the product to a pole. CABLE DESCRIPTION Sensor and power connection cable Cable L=5m equipped with connector for 1 sensor, power cable (L=2m) and pump control cable. 2 sensors and power connection cable Cable L=5m equipped with connectors for 2 sensors, power cable (L=2m) and pump control cable. 4 sensors and power connection cable Cable L=5m equipped with connectors for 4 sensors, power cable (L=2m) and pump control cable. Level sensor cable and power connection cable Cable L=5m to connect directly the level sensor , power cable (L=2m) and pump stop cable. Table 2 - Accessories

- 7 ENGLISH 9 TECHNICAL DATA Indicator Dimensions(mm): 173x 58 x 46 (without fixing support) Indicator weight (gr): ~ 600 Indicator Case: PA66 IGF 30 % native color RAL 9005 Indicator Protection: IP 67 Operating temperature: -20 / +65 °C Power supply: 9,5 – 32 Vd.c. (alarm “LOW BATTERY” < 9,5 Vdc) Display: Alphanumeric display 16 column x 2 rows area dimensions 123 x 30.4 mm with backlight Display view: > 2 mt Types of power and connection cables: See table 2 - Accessories Maximum relay output absorption: 100 mA Table 3 - Technical Data

8 - 10 INSTALLATION OF COMPONENTS 10.1 CONFIGURATIONS 10.1.1 Indicator GeoSystem 200 On the front side of the indicator, there are a series of keys that allow to configure the treatment parameters and to set the relative values, in according to the type of the installed spraying system. Picture 2 – Indicator 1. ON / OFF key. 2. Function and setting key 3. Alphanumeric display 2 rows for 16 characters with backlight. The system is supplied with pre-drilled mounting bracket. It is provided for a fastening system (optional) with dedicated accessories. Application zone of self-adhesive labels with production codes, model, and serial number. Picture 3 - Back side of the indicator 1 3 2

- 9 ENGLISH 10.1.2 How to fix the bracket Picture 4 – Bracket installation 1. Place the bracket (piece no. 1) in the side of the indicator marked with the letter A. 2. Use the screws M3x12 (pieces no. 2 and 3) provided with the kit to fix the bracket to the box (the screws are specific for the installation of this component) 3. Fix the bracket in the fixing holes B and C using the above mentioned screws, following the direction recommended by the dotted lines. It is recommended to use a maximum 1,2 N m tightening torque.

10 - 10.2 CONNECTIONS SCHEME 10.2.1 GeoSystem 200 - system connected with 4 sensors Option with 4 sensors: GEOline cable code: 989-0267 TECOMEC cable code: C00902038 Table 4 – Connection cables codes 4 sensors

- 11 ENGLISH 10.2.2 GeoSystem 200 – possible configuration of the system with 2 sensors Option 1: GEOline cable code: 989-0451 TECOMEC cable code: C00902037 Option 2: GEOline cable code: 989-0451 TECOMEC cable code: C00902037 Option 3: GEOline cable code: 989-0451 TECOMEC cable code: C00902037 Option 4: GEOline cable code: 989-0520 TECOMEC cable code: C00902058 Option 5: GEOline cable code: 989-0451 TECOMEC cable code: C00902037 Option 6: GEOline cable code: 989-0451 TECOMEC cable code: C00902037 Table 5 - Connection cables codes 2 sensors

12 - 10.2.3 GeoSystem 200 – system connected with 1 sensor (flowmeter / tank level sensor / pressure sensor / speed sensor) Picture 5 – Possible connections between indicator and sensors Option 1: GEOline cable code: 989-0449 TECOMEC cable code: C00902036 Option 2: GEOline cable code: 989-0266 TECOMEC cable code: C00902035 Option 3: GEOline cable code: 989-0449 TECOMEC cable code: C00902036 Option 4: GEOline cable code: 989-0266 TECOMEC cable code: C00902035 Table 6 - Connection cables codes 1 sensor

- 13 ENGLISH 10.3 COMPUTER INSTALLATION 10.3.1 Advice for the location The computer GeoSystem must be positioned in the command cabin of the farm vehicle taking care to observe the following precautions: - Make sure that the monitor is not placed in areas subject to vibrations or crashes, this could damage the equipment or activate the buttons unintentionally; - Fix the device in a place that is visible and easy to reach with your hands. - The monitor should not obstruct the movement or limit the control visibility. 10.4 SPEED SENSOR INSTALLATION Picture 6 - Proximity Installation 10.4.1 Advice for the location The speed sensors must be positioned taking care to observe the following precautions: - Install the sensor at 4-5 mm away from the body to detect; - Do not install the sensor body too near to other metal objects that may affect the operation of the detector.

14 - 10.5 FLOWMETER INSTALLATION Picture 7 - Flowmeter Installation 10.6 CHECK HARDWARE INSTALLATION Before to start with the use of GeoSystem 200 check the correct installation of each component: • Check that the connectors are in the right locations • Check that the cables have the right length • Check that all screws are tight • Check the polarity and the supply voltage GeoSystem must be powered directly from the battery, it must not be connected to an outlet controlled by a master key. In case of use of groups of valves equipped with a calibrated return, the displayed value corresponds to the real one only if all sections are completely open.

- 15 ENGLISH 11 INTERFACE DESCRIPTION OF INDICATOR 11.1 TABLE LIST OF BUTTONS AND THEIR FUNCTIONS Monitor with alphanumeric display and buttons Picture 8 – Indicator CONTROL KEYS, SELECTION OR MODIFICATION ON / OFF key: Turn on / off the indicator Key command: - It returns to the previous menu - It enables and disables the hold function - Holding down this button for more than 5 seconds, it reset the counters of the current treatment UP key: - It flows through the individual entries to the previous menu - Increase the value of the parameter During the modification of parameters, pressing the button permit to increase quickly the input values DOWN key: - Scrolls through the individual items through to the next menu - Decrease the value of the parameter During the modification of parameters, pressing the button permit to decrease quickly the input values Confirm key: - Confirm the access to the selected menu or parameter value previously modified - Holding down this button for more than 2 seconds, it display the values of the stored treatments

16 - 11.2 MENU STRUCTURE GeoSystem 200 menu are shown in the figure, in order to enter in the various items press the buttons or combinations of buttons located on the front panel of the monitor. Picture 9 – Menu map

- 17 ENGLISH 11.3 CONFIGURATION GENERAL PARAMETERS Allows to set the parameters necessary for the proper operation of the indicator. 1 Turn on by pressing . 2 The first message “GEOline GeoSystem 200” will appear on the display 3 It shows the Firmware revision and the system name: Sprayer. 4 Then, it appears the message “Please Wait” 5 Working values depends on installed sensors. 6 Keep pressing simultaneously and in order to enter in the configuration menu. 7 Scroll through the menu items using the and keys. 8 Press the key in order to modify the parameter: through the and keys is possible to change the value.

18 - If the fields contains default values or names, they will be displayed recursively by pressing and keys. If the input value is numeric, it will be increased or decreased according to the duration of the key press with an exponential interval. It is possible to cancel the current selection or return to the previously menu by pressing the key. 11.3.1 LIST OF MENU ITEMS OF GENERAL CONFIGURATION 1 Language: Italian/English/Spanish/French/German/ Portuguese/ Finnish/Russian/Polish. 2 Units: Metrics (l/ha, Km/h, bar) / US (GPA, mph, psi). 3 Vehicle identification: (1-5) it identifies the vehicle on which the system is installed. * By entering this configuration, you set the parameters for that particular vehicle (in this example: vehicle 1). 4 Connected sensors: It identified the number and the type of sensor connected to the indicator: Level, Flowmeter, Speed, Pressure, Flow+Level, Speed+Pressure, Flow+Pressure, Flow+Speed, RPM+Level, RPM+Pressure, All sensors (Flow, Speed, Pressure and Level).

- 19 ENGLISH Following parameters will be available according to the value set in the parameter above. Only if the parameter is set on “All sensors”, all the following parameters will be displayed. For the other configurations, the parameters available are listed in the table here beside: Connected sensors Available parameters Flow Flowmeter cal. Minimum flow Maximum flow Tank capacity Low tank level Corr.fact.visco Speed Speed calib. Simulated speed Speed sim. value Treatment width Pressure Pressure calib. Min. pressure Level Low tank level Specific weight Reading Filter Enable out calib RPM RPM Constant 5 Flowmeter calibration: It specifies how many pulses arrive to the flowmeter per amount of liquid sprayed. 1-5000 pulse/liter (Metric) or pulse/USG (gallon) (US). The value is indicated in the label on the body or by manufacturer. 6 Alarm threshold minimum flow: 0-10000 l/min (Metric) or USGpm (gal/min) (US) 7 Alarm threshold of maximum flow: 0-10000 l/min (Metric) or USGpm (gal/min) (US). 8 Speed sensor calibration: 2 mode: Constant wheel = distance traveled (cm or inches) / (number of pulses per revolution * wheel speed) or Automatic over a distance of 100 meters it is acquired pulse count.

20 - 9 Sensor pressure calibration: 0-200 F.S. value (bar or psi). 10 Tank capacity: 0-10000 liter (Metric) or USG (gal) (US). 11 Alarm threshold of minimum tank level: 0-10000 liter (Metric) or USG (gal) (US). 12 Simulated speed: Yes/No. 13 Simulated speed value: 0-50 Km/h (metric) or mph (U.S.) 14 Treatment width: 0-100 mt (metric) o 0-328.08 ft (US) 15 Sensitivity to change in velocity: it changes the response time of the speed, from the value 1 (fast) to the value 5 (slow). By increasing this value, you will increase the precision but you will reduce the speed variation. 16 Specific weight liquid tank: Only if the presence sensor level = YES, it allows to calculate the level of the tank in function of the specific weight of the liquid inside. 17 Presence sensor level: If you choose YES, the measured level is used in the replenishment procedure of the tank. If you choose NO, it shows the pre-setting value.

- 21 ENGLISH 18 Minimum pressure: 0-200 bar An alarm is generated after 15 seconds with a value below the minimum pressure. 19 Viscosity corrective factor: Value of the corrective factor of the flow in function of the viscosity of the liquid. 20 Reading filter: Value of the filter during the reading of the tank level. 10-20-40-60 21 Enable output calibration: If you choose YES, the relays output of pump will be activated during the tank level calibration. Use this for output calibration. 22 RPM Constant: 1-1000 Number of pulses for revolution Example RPM Minimum and Maximum measurable in function of the RPM constant: RPM Constant RPM Minimum RPM Maximum 1 20 60000 4 5 12000 20 1 3000 11.4 EXECUTION WORKING CYCLE It concerns the data management during the operating cycle. The indicator performs, according to the parameters configured, the acquisitions of the measures on the various sensors and the adjustment required. 1 Turn on by pressing . 2 The first message “GEOline GeoSystem 200” will appear on the display.

22 - 3 It shows the Firmware revision and the system name: Sprayer. 4 Then, it appears the message “Please Wait”. 5 The current dosage values appears. In the bottom line the speed of advancement of the vehicle. This visualization is available during the work (working values displayed when the indicator is connected with 4 sensors). 6 The indicator displays the single values measured and calculated through & keys. 11.4.1 LIST OF AVAILABLE VALUES IN THE WORKING CYCLE – Sistem connected with 2 RPM sensors 1 Current value of RPM and level In the upper row is displayed the value of RPM, while in the bottom one the tank level 2 Value of rotation speed RPM It shows the current rotation speed, measured in rotations per minute 3 Current tank level:

- 23 ENGLISH 11.4.2 LIST OF AVAILABLE VALUES IN THE WORKING CYCLE – Sistem connected with 2 RPM sensors + pressure 1 Current value of RPM and pressure In the upper row is displayed the value of RPM, while in the bottom one the pressure value 2 Value of rotation speed RPM It shows the current rotation speed, measured in rotations per minute 3 Current pressure value it is displayed only in this situation: - Value of pressure calibration ≠ 0 Keep pressed the key for 5 seconds to set zero the pressure value 11.4.3 LIST OF AVAILABLE VALUES IN THE WORKING CYCLE – Indicator connected with 4 sensors 1 Current value of the pressure It is displayed only in this situations: - Value of pressure calibration ≠ 0 Keeping pressed the key for 5 seconds to set zero the pressure value. 2 Current value of the speed 3 Current value of the flow rate in liters / minute (or gallons / minute)

24 - 4 Extension of the treated area since the beginning of treatment (value displayed only if the parameter “Treatment width” has been configured with a value greater than zero) 5 Total of the liquid sprayed since the beginning of treatment (value displayed only if the parameter “Treatment width” has been configured) 6 Current level of the tank: With this indication, it is possible do the following operations. Press the key if you want to modify the tank value using the and keys. Press again the key to confirm the value. While increasing the value of level, if you keep pressed the key without releasing it, the value will increase and after 30 units it will pass to tens to accelerate the operation. Keeping pressed the key for 5 seconds to set the initial tank capacity ( see the Tank Capacity parameter). If the level sensor parameter is YES the value set will be the level measured by the sensor. After the 5 seconds a massage appears : Completed!

- 25 ENGLISH 7 Duration of the last treatment (hh:mm) 8 Traveled distance since the beginning of the last treatment (Km) 9 At the end of the menu, you return to the initial display of the current dosing and those specified. 10 Press and hold the key for 5 seconds in order to reset all counters related to the ongoing treatment. After the 5 seconds, a message appears: Completed! Release the key before the 5 seconds to cancel the reset. 11.5 CALIBRATION MENU These operations must be carried out when the treatment is not active. - MANUAL TANK LEVEL CALIBRATION: It sets the calibration points related to the level sensor of the tank. - AUTO TANK LEVEL CALIBRATION: It sets the calibration points related to the level sensor of the tank automatically using a Flowmeter and setting the parameter Connected Sensor = Flow + Level or All sensors. In order to carry out this calibration it is required the 2 or 4 sensors connection cable. - SPEED SENSOR CALIBRATION: It calculates the ratio distance and pulses based on a known distance to travel (100 m in EU and 300 feet in US). MANUAL TANK LEVEL CALIBRATION Procedure to set calibration points related to the level sensor of the tank. 1 Turn on the indicator by pressing .

26 - 2 Keep pressing simultaneously and keys. 3 Slide the 2 voices of calibration through and keys until the message “1 Man. Tank cal.” appears. 4 Press the key and set the face value of the tank capacity by pressing the and keys (see the example in the picture). 5 The first value has to be acquired with the tank completely empty, with the liter value corresponding to 0. 6 Press the key to confirm. 7 The indicator, during the stabilization phase, will show the engineering value corresponding to the analog current value of the level sensor of the tank. 8 At the end the total value of the liquid introduced in the tank will be shown for 2 seconds. 0 for the first interval, ex. 200, 400, 600 etc. 9 Insert in the tank a determined water quantity and set the same value in the second interval. In the following intervals: Level 3/200, Level 4/200 etc. has to be entered the water value actually entered in each interval and not the total one. The indicator shows the same value previously entered and will calculate the total for each interval (Es. Level: 200 l, Level: 400 l, Level 600 l…)

- 27 ENGLISH 10 After having entered all the intervals until the maximum tank capacity, press the key to finish and then the key for 2 seconds to confirm and save the calibration. By pressing the key for 2 seconds the calibration will be cancelled and pressing the or keys for 2 seconds it will be possible to restart the procedure. 11 AUTOMATIC TANK LEVEL CALIBRATION* *choice available only in the configuration with level sensor and flowmeter. 12 Fill up the tank up to its max. capacity, then press the key in order to enter in the tank configuration and to set the value of the max. tank capacity. 13 Open the tap (or valve) connected to the flowmeter in order to drain the water. If an electrically controlled valve is available, it is possible activate through the relays output (if "Output Enable in Calibration" is been enable (Yes). See the diagram of picture 10. The following values will be displayed: current interval indication, the measured level value expressed in Engineering units (value of A/D convertor) and the commensurate value expressed in liters (or USG value).

28 - 14 The calibration process could be interrupted at any time by pressing the key. 15 When the tank is completely empty, press the key in order to save the current calibration. 16 SPEED SENSOR CALIBRATION* *choice available only in the configuration with speed sensor. 17 Press the key to enter into the calibration. 18 The message “Counter value” appears, it will increase as the tractor moves towards the finish line. 19 Press the key when the tractor crossed the line (100 m in EU and 300 feet in US) in order to complete the calculation of the speed constant. 20 Press the key in order to return to the previous menu.

- 29 ENGLISH 21 SAVE TANK PROFILE* *choice available only in the configuration with level sensor. In order to save the tank profile on a USB key, it is necessary to have the suitable adapter or contact the supplier. On the USB key, individual files will be created for each vehicle ID and current profile. The file name is TANK_xx.PRO, where “xx” specifies the ID of the selected vehicle (01,02,03,04,05). 22 LOAD TANK PROFILE* *choice available only in the configuration with level sensor. In order to load the tank profile on a USB key, it is necessary to have the suitable adapter or contact the supplier. A separate file for vehicle ID and current profile must be present on the USB key. The file name is TANK_xx.PRO, where “xx” specifies the ID of the selected vehicle (01,02,03,04,05). Picture 10 – Diagram for the automatic calibration of tank level

30 - 11.6 VALUE OF SOFTWARE PARAMETERS Limit values of the setting software parameters. Parameter Description Min. / U.M. Max. / U.M. Note Language Message language ENG/ITA/SPA/DEU/ FRA/POL/RUS/FIN/POR Unit Used metric system l/ha, Km/h, bar o GPA, mph, psi Metrics/ US ID Vehicle Vehicle on which the system is installed 1 5 Connected sensors Sensors currently in the system Level/Flowmeter/Speed/Pressure/Flow+Level/ Speed+Pressure/Flow+Pressure/Flow+Speed/ RPM+Level/RPM+Pressure/All sensors Flowmeter Calibration Constant Flowmeter Value 1 imp/l 4 imp/USG 5000 imp/l 18927 imp/USG Metrics/ US Minimal flow Alarm threshold minimum flow 0 l/min 0 USGpm 10000 l/min 2642 USGpm Metrics/ US Maximum flow Alarm threshold maximum flow 0 l/min 0 USGpm 10000 l/min 2642 USGpm Metrics/ US Speed Calibration Speed sensor calibration 0.0 cm/imp 0.0 in/imp 6000.0 cm/imp 2362.2 in/imp Round pulse Num. * wheel rounds Pressure Calibration Pressure sensor calibration 0 bar 0 PSI 200 bar 2901 PSI Value of bottom scale Tank capacity Value the tank can contain 0 l 0 USG 10000 l 2642 USG Metrics/ US Minimum Tank level Alarm threshold minimum level tank 0 l 0 USG 10000 l 2642 USG Metrics/ US Simulated speed Simulated speed No Yes Simulated speed value Simulated speed value 0 km/h 0 mph 50 km/h 31 mph Metrics/ US Treatment width Value of the width between rows /spraying boom width 0.00 mt 0.00 ft 100.00 mt 328.08 ft Metrica/US Speed response Sensitive to the speed variation 1 5 1 fast 5 slow Specific weight specific weight of tank liquid 0.00 10.00 Level sensor Level sensor NO Yes Mini. Press. 0 bar 0 psi 200 bar 2901 psi Corrective viscosity factor Corrective viscosity factor 0.00 10.00 Reading filter Filter for reading the tank level 10 – 20 - 40 - 60 Enable out calibration Pump start up Yes No RPM Constant 1 1000 pls/rev Table 7 - General Parameters

- 31 ENGLISH 12 HW TEST It allows to effect the hardware test. This test can be carried out only at system boot. 1 Turn on the indicator by pressing . 2 After viewing the software revision, when the message “Please Wait” appears, press simultaneously the and keys. 3 The message “Test HW” appears. 4 The value of Voltage appears and it is possible to slide the following values through and keys. 5 The next data is the value of the analog input 1 of the Switch Box board corresponding to the pressure sensor. 6 The next data is the value of the analog input 2 of the Switch Box board corresponding to the tank level sensor.

32 - 7 The next data is the value of the external counter 1 corresponding to the input of the flowmeter. 8 The next data is the value of the external counter 2 corresponding to the input of the speed sensor. 9 This passage allows to check the correct functioning of the keys. The message “Press a key” will be displayed. 10 By keeping pressed a key, the name of the key appears temporarily on the display. By pressing the Reset key, first the message “RESET KEY” appears; then the indicator goes on to the buzzer test. 11 Buzzer test. During this passage an acoustic signal will be generated, confirming the correct functioning of the buzzer. 12 Pump start up test. During this passage the pump will be activated when you press the key. 13 Press the key in order to return to the normal operation of the indicator. 14 To repeat the TEST HW it is necessary to switch off and on again the indicator.

- 33 ENGLISH 13 USE OF GEOSYSTEM 200 13.1 DISPLAY – EXAMPLE OF VISUALIZATION WITH 4 SENSORS Figure 11 -Display *the displayed working values as well the layout of the display change in according to the value set in the parameter “Connected sensors”. 13.2 DEFINITION OF TANK REPLENISHMENT The system can measure the quantity of the refilling liquid using the level sensor or the flowmeter, if present. This mode is possible only if the parameter “Connected Sensors” is enabled and set on “Flowmeter”. The operative procedure is explained in the paragraph 13.8 .

- 35 ENGLISH 13.3 DEFINITION OF TREATMENT The term treatment means the set of data recorded during an activity of weeding or sprayer. The working parameters recorded by GeoSystem are stored in a queue. The queue can store a maximum of 20. The data of each treatment can be visualized through the appropriate keys. Every time you start a new treatment the data of the current treatment are inserted in the queue. The treatment number 1 is the last treatment saved. Treatment number 2 is the second last treatment saved and so on. All treatments inserted in the queue slip of a position at the moment of every saving. When the queue is full, the recording of a new treatment causes the cancellation of the treatment less recent (that in twentieth position). After the treatment n° 20, appears the value “Total”, that refers to the historical data related to all the treatments. This value cannot be deleted, not even through the RESET procedure. 13.4 NEW TREATMENT 1 To start the recording of data on a new treatment, select a parameter of any work cycle, with the exception of the parameter: "Tank Level". 2 Press the key for 5 seconds. 3 By now, the counters are all reset. The parameter “Tank level” is a special parameter: If it is selected, the pressing of the button for 5 seconds DO NOT prepare the system for a new treatment but for a new filling of the tank.

36 - 13.5 TURNING ON GeoSystem 200 1 Turn on the indicator by pressing . 2 The message “GEOline GeoSystem 200” will appear on the display and immediately the software revision. 3 It shows the Firmware revision and the system name: Sprayer. 4 After which it appears the message “Please wait” 5 The working values appears on the display and, eventually, additional markings such as(working values displayed when the indicator is connected with 4 sensors): 6  the sign “►”at the bottom left: it signals that the treatment is in action. 7  the sign “▌▐” at the bottom left: it signals that the treatment is in pause. 8  the sign “@”: it indicates that the data represented on the right is calculated or simulated and it does not originate from the reading of one specific sensor. E.g. the represented speed is a simulated value. 9  The symbol in the upper right: it indicates the presence of an alarm; 10  The number in the upper left: it indicates the ID-Vehicle

- 37 ENGLISH 11  The symbol”←→” in the upper left: it indicates that the parameter “Treatment width” has been configured. The value must be greater than zero. If this value is not set up, the extension of the treated area cannot be calculated. If this parameter is not configured, the symbol “←→”” won’t be displayed . Instead of the current dosage value, appears the instant flow rate value (l/min). 12 During the execution, it is possible to temporary stop the calculation by pressing the key for 1 second. Press again the same key to reactivate the calculation. 13 At the starting, press simultaneously the keys to reset all the parameters of the indicator to the initial values. 13.6 TURNING OFF GeoSystem 200 1 Press the key in order to turn off the system. 2 Wait that the data of the last treatment will be saved. While switching off do not press any key and do not remove the power, until the control unit turns off. Always use the appropriate button to turn off the computer, otherwise all the data relating to treatments and schedules will be lost.

38 - 13.7 TREATMENT 1 Turn on the indicator by pressing the key. 2 Set tank level. See paragraph current level of the tank. 3 To start the data recording of a new treatment, select a parameter of the any cycle work, with the exception of the parameter” tank level”. 4 The system store the treatment data in a queue of 20 elements. 5 Press for 5 seconds the key to save the last data stored in the queue and to reset all the meters, prearranging the data recording of the new treatment you will do. N.B. if level sensor is not present, pressing the key, you will reset all the working data, except the tank level that is recharged to the pre-set value during the configuration phase. The treatment data are stored only if you have set the parameter “connected sensor”= Flow+Speed or All sensors. 13.8 TANK REPLENISHMENT USING AN EXTERNAL PUMP This procedure is available only in the configurations “ Sensor present with flowmeter or level sensor”. 1 If the field to treat requires an amount of liquid higher than the amount of the tank, it will be necessary to fill once or more times the tank. 2 At every replenishment you have to update the tank level ( parameter: “Tank Level ”)

- 39 ENGLISH 3 Select the indication: “Tank Level” 4 Press for 2 seconds the key. 5 Set the value (in liters) of liquid which will be poured in the tank using the and keys. 6 Press the key to start the tank replenishment. The pump will start. 7 During the tank replenishment it is possible to stop and restart the pump pressing the key. 8 When the set value is reached, the replenishment process will be interrupted and the pump stopped. 9 Press the key to exit and repeat the process or the key again in order to return to the tank level indication. The parameter “Tank level” is a special parameter: if you DO NOT select the parameter “Tank level” the pressure of the key for 5 seconds will prepare the system for a new treatment, resetting all the counters.

40 - 13.9 SETTING TANK “ZERO” LEVEL This procedure is available only in the configurations “ Sensor present with flowmeter or level sensor”. 1 If during the first installation or when the tank is empty, the displayed tank level is DIFFERENT from zero, it is necessary to set the zero level of the tank. 2 Select the indication: “Tank Level” and. 3 Make sure that the tank is completely empty and press for 5 sec. the key 4 If everything is successful, the message “Completed!” will be displayed. The process of setting tank zero level must be carry out only when a new tank profile has been loaded or when the ID vehicle has been changed. if you DO NOT carry out this process in the abovementioned cases, the tank level indication could be not correct.

- 41 ENGLISH 13.10 TOTALIZERS (AVAILABLE WITH THE CONFIGURATIONS CONNECTED SENSORS OF FLOW AND SPEED) It allows to check the counters related to working. 13.10.1 READING TOTALIZERS 1 Turn on the indicator by pressing . 2 Press and hold the key for 3 seconds to access the statistics of the operating mode. 3 Shows the name of the totalizer and, at the bottom line, the total duration of the treatment. 4 Scroll the last 20 treatments through and keys. The totalizer N° 1 relates to the treatment more recently while the totalizer N° 20 is the oldest one. 5 After the treatment n° 20, appears the total value that refers to the historical data related to the treatments. 6 Press the key to verify the individual counts of each totalizer. Through and keys, display the values relating to the treatment carried out, such as:  The value of the treated area (ha)  The value of the total liquid sprayed (l)  The traveled distance (Km)

42 -  The duration of the treatment performed (hh:mm).  Average speed (km/h)  Maximum speed (km/h) 13.10.2 RESET TOTALIZERS 1 The indicator stored the data of treatment in a queue of 20 elements. 2 Press and hold the key for 5 seconds in order to save the last data stored in the queue and in order to reset all counters, preparing the recording of the data related to the new treatment that will be performed. Press key to confirm the reset or key to cancel. If the level sensor is not present, pressing the reset button will reset all work data, except the tank level, which is reloaded to the preset value during configuration. 13.11 RECALL DATA OF TREATMENTS 1 Press for 3 seconds the key, in order to access to the menu that allows to visualize the queue of last 20 treatments performed. 2 Using the and keys in order to scroll the list of treatments. Press the key in order to access to the content.

- 43 ENGLISH 14 ALARMS 14.1 WARNING AND ALARMS There are some warning and alarms to highlight unusual states that show anomaly functioning. At the activation o fan alarm, you will hear the buzzer. Press key to disable it. The active alarm state is highlighted by the sign on the right of the first line of the display. 14.2 LIST OF POSSIBLE ALARMS 1. Tank empty alarm: it gives this alarm when it reaches the minimum flow of liquid in the tank set with the parameter Alarm threshold minimum tank level 2. Minimum flow alarm: The amount of sprayed liquid (l/min) is lower than the parameter value Alarm threshold minimum flow 3. Maximum flow alarm: the amount of sprayed liquid (l/min) is higher than the parameter value Alarm threshold maximum flow 4. Low battery level alarm: the battery level is lower than 9.0 Volts 5. Low pressure alarm: The alarm is generated after 15 seconds with a pressure less than the parameter Minimum pressure

44 - 15 TROUBLESHOOTING DISPLAY CAUSE SOLUTION The display does not turn on There is not power. Check the connections on the power cable. The indicator is turned off. Press the turning on button. The counting of the travelled distance shown on the computer is different from the real one. Wrong programming Check the connection with the speed sensor. The reset of the totalizer has not been effectuated Reset the totalizer The counting of the travelled surface shown on the computer is different from the real one. Wrong programming Check the bar width programming The reset of the totalizer has not been effectuated Reset the totalizer The instant pressure is not shown. The indicator has not signal from the pressure sensor Check the connections with the pressure sensor Wrong installation of the pressure sensor Check the bottom scale programming for the pressure sensor The instant pressure visualized is inaccurate. Wrong programming Check the bottom scale programming for the pressure sensor The pressure sensor is not calibrated Do the calibration Wrong installation of the pressure sensor Check the connections with the pressure sensor The tank level visualized is inaccurate. The level sensor is not calibrated. Do the calibration. Repeat the level sensor calibration. Wrong installation of the level sensor. Check the connection with the level sensor Table 8 - Troubleshooting

- 45 ENGLISH DICHIARAZIONE DI CONFORMITA’ UE - EU DECLARATION OF CONFORMITY - EU KONFORMITÄTSERKLÄRUNG - DÉCLARATION UE DE CONFORMITÉ - DECLARACION UE DE CONFORMIDAD - EU ДЕКЛАРАЦИЯ О СООТВЕТСТВИИ Nr 09/16 IT Il sottoscritto, designato a legale rappresentante della GEOline Electronic s.r.l. , via Mondadori 15, Poggio Rusco (MN) ‐ Italy, dichiara che i prodotti sottoelencati: EN  The undersigned, an authorised officer of GEOline Electronic s.r.l. , via Mondadori 15, Poggio Rusco (MN) ‐ Italy, hereby declares that the products listed hereunder: D Der Unterzeichner, rechtlicher Vertreter der GEOline Electronic s.r.l. , via Mondadori 15, Poggio Rusco (MN) – Italy, erklärt, daß die nachstehend beschriebenen Produkte: FR   Je soussigné, représentant légal désigné de GEOline Electronic s.r.l. , via Mondadori 15, Poggio Rusco (MN) ‐ Italy, déclare que les produits énumérés ci‐après: ES   El suscrito, nombrado representante legal de la GEOline Electronic s.r.l. , via Mondadori 15, Poggio Rusco (MN) ‐ Italy, declara que los productos indicatos a continuación: RU    Нижеподписавшийся, являющийся законным представителем компании GEOline Electronic s.r.l., расположенной по адресу via Mondadori 15, Poggio Rusco (MN) – Italy, заявляет, что продукция ниже IT Sono conformi a quanto prescritto dalle seguenti direttive: EN Are in compliance with the following directives: D  Mit den Vorschriften konform sind, die in den folgenden Richtlinien: FR Sont conformes aux prescriptions des directives suivantes: ES Respetan las prescripciones contenidas en las siguientes directivas: RU     Соответствует требованиям следующих директив: IT E dalle seguenti norme: EN And with the following standards: D Und Normen stehen: FR Et aux normes ci‐apres: ES Y en las siguientes normas: RU       И следующих стандартов: IT E, in applicazione a quanto previsto dalle direttive citate, sono stati dotati di marcatura CE ed é stato predisposto un adeguato fascicolo tecnico presso la ns. sede. EN And, pursuant of the above‐mentioned directives, the CE mark has been applied. Furthermore, adeguate technical file has been prepared and is available from our offices. D Und daß sie in Übereinstimmung mit den Vorschriften der obengenannten Richtlinien mit dem CE‐Zeichen versehen sind und daß dafür ein angemessenes technisches Heft erstellt wurde, das bei uns in der Firma zur Verfügung steht. FR En application des directives citées, ils portent la marque CE et un dossier technique est deposé auprès de notre siège. ES Y, conforme con lo previsto en las citadas directivas, han recibido la marca CE. Existe asimismo un especifico prospecto técnico relativo disponible en nuestra sede. RU       И, в исполнении данных директив, был нанесен знак СЕ и соответствующее техническое досье было заведено в нашем офисе. Poggio Rusco, 20/04/2016 Andrea GHIRALDI GeoSystem 200 2014/30/EU EN ISO 14982 Agricultural and forestry machinery ‐‐ Electromagnetic compatibility ‐‐ Test methods and acceptance criteria

46 - 16 GUARANTEE The supplier guarantees, for 24 months from the delivery date, the good quality of materials used, the excellent construction and the steady functioning of the instrument they have manufactured and that bears the trademark or the production serial number. During the guarantee period the supplier undertakes to repair or replace, free supplier’s head office, faulty parts due to poor materials or faulty construction, provided that such parts are delivered free port supplier’s head office. Shortcomings and defects due to incorrect use of instruments, inadequate maintenance, changes carried out without the supplier’s approval, normal wear are not included in this guarantee. Liability and compensations by the supplier due to direct or indirect damages to persons, objects or production, even as a consequence of faulty functioning of the supplied instruments or of material or construction defects, are not included in this guarantee. GEOline electronic reserve itself the right to modify the contents of this manual caused by hardware and software implementations in order to a constant improvement of the product and so a better service to the user. NOTES:

SOFTWARE RELEASE 1.3.0 “QUICK REFERENCE” GeoSystem 200 TREATMENT PREPARATION 1 To start the data recording of a new treatment, select a parameter of any working cycle, except the “level tank” parameter. 2 The system stores the treatment data in a queue of 20 elements. 3 Press for 5 seconds the key to save the last stored data in the queue and to reset all the counters, prearranging the data recording of a new treatment you are going to do. N.B: if the level sensor is not present, the pressure of the key will reset all the working data, except for the tank level which is reload to a pre-set value in configuration phase. USE 1 Automatic functioning of the system: GeoSystem 200 shows and records the speed, flow, travelled distance, treated area, amount of sprayed liquid values. TANK REPLENISHMENT 1 If the treatment requires more chemical substance than how the vehicle tank can contains, the operator has the possibility to supply the tank with liquid and to eventually modify the insert quantity. 2 If the level sensor is not present, you have to manually set the tank level data. In this case select the “level tank” data and, only in this case, press the key to modify the data which is reloaded at the pre-set value in configuration phase. TREATMENT VISUALIZATION 1 Press for 3 seconds the key to enter into the menu that allows to visualize the queue of the last 20 treatments. 2 Using the and key, it is possible to scroll up and down the treatment list. Press to enter into the one of them.

SOFTWARE RELEASE 1.3.0 DISPLAY VISUALIZATION- EXAMPLE OF INDICATOR CONNECTED WITH 4 SENSORS ALARMS At the activation of one alarm you will hear a sound from the buzzer. Press to disable it. The active alarm state is highlighted by the sign on the right of the first line of the display. 1. Tank empty alarm 2. Minimum flow alarm 3. Maximum flow alarm 4. Low battery alarm 5. Low pressure alarm