GeMNeXT EXT-200-LAN Operation & User’s Manual

resolutions up to 120 meters away from your HDMI or DVI-D source by using one CAT5e/6 cable. With the advantage of TCP/IP standard，you can extend your HD video to multiple displays by using an Ethernet Switch. HDTV Resolutions 480p,576p,720p,1080p Audio Sample rate:32kHz,44.1kHz,48kHz IR remote control 38kHz;NEC HDMI HDMI 1.3 HDCP HDCP 1.2 Power adapter Input：100V-240V(50-60Hz) Output:5V/1A Power consumption HDMI Sender:3W HDMI receiver:3W Size(L-W-H) 92x79x20mm Weight 240g x 2 Operating Temperature/Humidity 0℃-70℃/10%-80%RH(no condensation) Storage Temperature/Humidity -10℃-80℃/5%-90%RH(no condensation)

➢ Support HDMI1.3 protocol. ➢ HDCP1.1 & 1.2 protocol compliant ➢ Support point-to-point mode, one point-to-many mode and cascade connection mode. ➢ Support IR extender function allows IR remote control of Source devices from remote viewing location by sending IR commands received in the vicinity of the Display back to the Source devices. ➢ Multiple Tx’s can be connected to a Managed Gigabit switch with VLAN/IGMP support therefore sending 1080p video signals to Rx connected to the Gigabit switch to show different sources on the HDMI displays. See further explanation in section 7. VLAN Support 3.PACKAGE CONTENTS Before attempting to use this unit, please check the packaging and make sure the following items are contained in the shipping carton: 1) Main unit No. 1 Sender , Main unit No. 2 Receiver 2) Two pieces of 5V DC Power Supply. 3) one piece of IR transmitter and one piece of IR receiver 4) Quick Set Up Guide

Reset Hold down the key for 5 seconds IR-out Connect IR transmitter this Port HDMI-in Connect HDMI sink source to this Port HDMI Receiver

Reset Hold down the key,the model will re-start IR-in Connect IR Receiver this Port HDMI-out Connect HDMI sink device to this Port 5.Connection and operation 1) Connect the HDMI source (such as DVD, PS3, STB ) to the HDMI IN of Sender. 2) Connect the IR sender to the Sender IR OUT Port, and Be Directed at HDMI video source’s IR receiver. 3) Connect the HDMI out of Receiver to HDTV display. 4) Connect the IR receiver to the Receiver IR IN Port. 5) Use one Cat5e/6 cable up to 120m to connect the Sender and Receiver. 6) Plug two pieces of 5V power supply into the Sender and Receiver. 7) Power on the HDTV display and HDMI source. 6.Application diagrams Application 1 – Point To Point

6. IP settings – GUI When typing the IP address as found on the Transmitter or Receiver he Graphical User Interface is displayed. Connect the laptop or PC that is connected from the LAN port of the laptop or PC to the RJ45 port of the Transmitter or Receiver. It is important to bring the IP address of the laptop or PC in range with the IP address of the Transmitter or Receiver. (see below)

In Status Display the Device status is shown with System Version and Rate Config (Input resolution and Output resolution. This is for Transmitter device or Receiver device. 6.2 System Config – Network config In Network config the device IP settings can be modified to bring all devices in the same range of your desired network. When you are using your production network it is advised to bring the receivers and transmitter in a VLAN set up in order to keep the transmission data for video isolated from your common network traffic.

The output resolution can be changed by picking an available resolution fro the drop-down list or you can match it with the Input resolution. 6.4 System Config – System update If a new system version is available in order to upgrade potential new or improved functionality this can be done by the System update button where a specific file can be uploaded. This would only be needed when communicated by GeMNeXT.

seconds. After this the device would be reset and this would automatically result in a changed IP address to a default IP address. Please note this default address is not the IP address described on the label on the device. Transmitters: 192.168.1.168 Receivers: 192.168.1.160 If you need to bring the unit back to the required IP settings you had entered before please change it back to those IP settings again. See 6.2 System Config – Network Config 6.6 Reboot To reboot the device press the Reboot button in the Interface.