Hyundai Kona Quick Reference Manual

Call “Dial 7-1-4-9-6-5-3-0-0-0” “Call John Smith” Command (If equipped) Example NAVIGATION Find Address “1-2-3-4-5 1st Street, Fountain Valley” Command Example Located on Rearview Mirror DESTINATION SEARCH BY VOICE Find “Find Lowe’s® near me” “Starbucks®” Improving how you store your contacts can optimize your Bluetooth® Voice Recognition performance: • Use full names instead of short or single-syllable names (“John or Dad”) • Avoid using special characters/emojis or abbreviations (“Dr.”) when saving contacts Find “Find McDonald’s®” Scheduled Maintenance (Normal Usage) 2.0 MPI 1.6 Turbo-GDI Engine Oil & Filter Replace 7,500 or 12 mos Replace 6,000 or 12 mos. Fuel Additives Add 7,500 or 12 mos Add 6,000 or 12 mos. Battery Condition Inspect 7,500 or 12 mos Inspect 6,000 or 12 mos Brake Lines, Hoses & Connections Front Brake Disc/Pads, Calipers Rear Brake Disc/Pads Steering Gear Box, Linkage & Boots, Lower Arm Ball Joint, Upper Arm Ball Joint Drive Shafts & Boots Suspension Mounting Bolts Air Conditioning Refrigerant Air Conditioning Compressor Propeller Shaft (AWD) Exhaust Pipe & Muffler Air Cleaner Filter Inspect 7,500 or 12 mos Inspect 6,000 or 12 mos Replace 30,000 or 48 mos. Replace 24,000 or 48 mos. Vacuum Hose Inspect 7,500 or 12 mos Inspect 6,000 or 12 mos. Climate Control Air Filter (For Evaporator and Blower Unit) Replace Every 12 mos. Replace Every 12 mos. Tire Rotation Perform 7,500 Perform 6,000 Vapor Hose, Fuel Tank Cap, Fuel Tank Inspect 15,000 or 24 mos. Inspect 12,000 or 24 mos. Fuel Tank Air Filter Fuel Filter Parking Brake Inspect 15,000 or 24 mos. Inspect 12,000 or 24 mos. Brake Fluid Fuel Lines, Fuel Hoses & Connections Inspect 30,000 or 48 mos. Inspect 24,000 or 48 mos. Rear Axle Oil (AWD) Inspect 30,000 or 48 mos. Inspect 24,000 or 48 mos. Transfer Case Oil (AWD) Drive Belts Inspect First 60,000 or 72 mos. Inspect First 60,000 or 72 mos. Subsequent, every 15,000 or 24 mos. Subsequent, every 12,000 or 24 mos. Spark Plugs Replace 97,500 Replace 42,000 Engine Coolant Replace First 120,000 or 120 mos. Replace First 120,000 or 120 mos. Subsequent, every 30,000 or 24 mos. Subsequent, every 30,000 or 24 mos. Valve Clearance (Only 1.6 T-GDI) Inspect - Inspect 75,000 Intercooler, in/out hose, air intake hose (Only 1.6 T-GDI) Inspect - Inspect 6,000 or 12 mos. EcoShift Dual Clutch Transmission Fluid (Only 1.6 T-GDI) - Inspect 6,000 or 12 mos. Automatic Transmission Fluid (Only 2.0) No check or services required for Normal Usage driving. _ *See Owner’s Manual for details. Looking for more detailed information? This Quick Reference Guide does not replace your vehicle Owner’s Manual. If you require additional information or are unsure of a specific issue, you should always refer to the vehicle Owner’s Manual or contact your authorized Hyundai dealer. The information contained in this Quick Reference Guide was correct at the time of printing; however, specifications and equipment can change without notice. No warranty or guarantee is being extended in this Quick Reference Guide, and Hyundai reserves the right to change product specifications and equipment at any time without incurring obligations. Some vehicles are shown with optional equipment. Specifications apply to U.S. vehicles only. Please contact your Hyundai dealer for current vehicle specifications. NP150-J92020 (Rev 06/03./19) Printing 06/06/19 MAINTENANCE Unit: mile ☐ MANUAL / AUTOMATIC CLIMATE CONTROL - pages 11 - Explain different air modes to a customer. Manual Automatic + - + - ☐ DEFROST - page 11 1 Press the front defrost button. 2 Set to warmest temperature setting. 3 Set to medium fan speed. Roadside Assistance: 1-800-243-7766 Consumer Affairs: 1-800-633-5151 Sirius XM® Radio: 1-800-967-2346 Blue Link: 1-855-2BLUELINK (1-855-225-8354) Quick Reference Guide The Hyundai KONA Sales Consultant Date Sales Manager Date Customer Date Email ☐ INTRODUCTION AND LOCATION OF THE SERVICE DEPARTMENT ☐ SET FIRST SERVICE APPOINTMENT ☐ REVIEW FACTORY RECOMMENDED MAINTENANCE SCHEDULE ☐ WAS THE CONDITION OF YOUR VEHICLE (AT DELIVERY) TO YOUR SATISFACTION? ☐ VOICE RECOGNITION - Review Voice Recognition tips - Show Voice Recognition tear off card and have owner place in convenient location ☐ BLUE LINK - Assist with creating MyHyundai.com account - Assist with Blue Link enrollment - Show Blue Link User's Manual - Encourage customer to download the MyHyundai with Blue Link app

Your Hyundai vehicle may be equipped with technologies and services that use information collected, generated, recorded or stored by the vehicle. Hyundai has created a Vehicle Owner Privacy Policy to explain how these technologies and services collect, use, and share this information. You may read our Vehicle Owner Privacy Policy on the Hyundaiusa.com website at https://www.hyundaiusa.com/owner-privacy-policy.aspx If you would like to receive a hard copy of our Vehicle Owner Privacy Policy, please contact our Customer Connect Center at: Hyundai Motor America Hyundai Customer Connect Center P.O. Box 83835 Phoeniz, AZ 85071-3835 800-633-5151 [email protected] Hyundai's Customer Connect Center representatives are available Monday through Friday, between the hours of 5:00 AM and 7:00 PM PST and Saturday and Sunday between 6:30 AM and 3:00 PM PST (English). For Customer Connect Center assistance in Spanish or Korean, representatives are available Monday through Friday between 6:30 AM and 3:00 PM PST.

learn about the features that will enhance your enjoyment of your Hyundai. More detailed information about these features are available in your Owner’s Manual. Headlights and Fog Lights Page 05 Instrument Cluster Page 07 Steering Wheel Audio Control Page 15 Instrument Cluster Menu Buttons and Cruise Control Page 35 Climate Control Page 11 WARNING! To reduce the risk of serious injury to yourself and others, read and understand the important SAFETY INFORMATION in your Owner’s Manual. FEATURES AND CONTROLS Child-protector rear door lock 03 Climate Control 11 Headlights and Fog Lights 05 Head-Up Display 08 Instrument Cluster 07 Instrument Panel Illumination 10 Interior Lights 03 LCD Display Control 09 LCD Display Modes 09 Sunroof 04 Seat-Front Seat Adjustment 02 Smart Key 01 Warnings and Indicators 10 Wiper and Washer 06 MULTIMEDIA Android Auto™ 25 Apple Carplay™ 27 AUX and USB Port 24 Blue Link Telematicm System 18 Bluetooth Operational Tips 16 Bluetooth Phone Pairing 15 Navigation 22 Radio Mode 21 Steering Wheel Audio Control 15 Voice Recognition 17 Wireless Cellular Phone Charging System 23 DRIVING AWD Lock 34 Blind Spot Collision Warning (BCW) 33 Cruise Control/Smart Cruise Control 35 Downhill Brake Control (DBC) 32 Drive Mode Integrated Control System 34 Forward Collision-Avoidance Assist (FCA) 36 Lane Keeping Assist (LKA) 33 Tire Mobility Kit 37 Tire Pressure Monitoring System (TPMS) 31 * Some vehicles may not be equipped with all the listed features.

Quick Reference Guide I 02 01 I Quick Reference Guide KONA HYUNDAI Driver’s Door Lock / Unlock Smart key must be within 28~40in. from the outside door handle. Press : One time -Unlock driver door Two Times - Unlock all doors Three times - Lock all doors Folding/Unfolding the Rear Seat 1. Lower the rear head restraints to the lowest position. 2. Pull the seat belt to the side before folding down the seatback. 3. Remove the seat belt from the guide , pull the lever and fold the seat toward the front of the vehicle. 4. To unfold the rear seat, pull the seat belt to the side and push the seatback until it is firmly latched into place. Removing the Mechanical Key Press and hold the release A button and remove the key. NOTE : For the User Selectable Option, please refer to your Owner’s Manual for further information. (Does not open liftgate) Lock Unlock Panic Liftgate Unlock SMART KEY A FRONT SEAT ADJUSTMENT (manual) Forward and Backward Seat Height (for the driver’s seat) Seatback Angle FRONT SEAT ADJUSTMENT (power) Forward and Backward Seat Height Seatback Angle Lumbar Support (for the driver’s seat) Push down several times on the lever to lower. Pull up several times on the lever to raise. REAR SEAT FOLDING

Quick Reference Guide I 04 03 I Quick Reference Guide KONA HYUNDAI INTERIOR LIGHTS 1 Map Light Press the lens to turn map lights ON or OFF. 2 Door position Cabin light ON when door(s) and/or tailgate are open. 3 Cabin Light ON position Press the switch to the left to turn on cabin light. 4 Cabin Light OFF position Press the switch to the right to leave cabin light off. Without Sunroof With Sunroof 1 1 2 2 1 1 3 3 4 4 Sliding the Sunroof Pressing the sunroof control lever backward or forward momentarily to the second detent position completely opens or closes the sunroof even when the switch is released. To stop the sunroof at the desired position while the sunroof is in operation, press the sunroof control lever backward or forward and release the switch. Tilting the Sunroof Open Push the sunroof control switch upward to tilt the sunroof. Close Push and hold the sunroof control switch forward to close the sunroof. SUNROOF The sunshade will open automatically with the sunroof when the glass panel moves. If you want it closed, move the sunshade manually. Sunshade Lock Insert a key into the hole and turn it to the lock position. Unlock Insert a key into the hole and turn clockwise to the unlock position. CHILD-PROTECTOR REAR DOOR LOCK

Quick Reference Guide I 06 05 I Quick Reference Guide KONA HYUNDAI Wash with Brief Wipes OFF HI LO OFF MIST PULL INT INT LO HI OFF HI LO OFF MIST PULL INT INT LO HI Rear Wiper / Washer Control HI - High wiper speed LO - Low wiper speed OFF - Off • Push away for rear wash Intermittent Wipe Time Adjustment More frequent wipes Less frequent wipes OFF HI LO OFF PUSH MIST PULL INT INT LO HI MIST - Single wipe OFF - Off INT - Intermittent wipe or AUTO - Auto control wipe LO - Low wiper speed HI - High wiper speed MIST OFF INT or AUTO LO HI WIPER AND WASHER High Beam/ High Beam Assist High Beam/ High Beam Assist Fog Lights OFF OFF OFF OFF Turn Signals and Lane Change Signals AUTO OFF OFF Flashing the Headlights Headlights Delay Headlights may stay on for 15 seconds after exiting and locking up the vehicle. Press the remote lock button twice to turn the headlights off. Please refer to your Owner’s Manual for further information. 1. Select auto position on stalk. 2. Push lever forward to engage Auto High Beam. 3. Push lever forward again to disengage. Parking Lights All Lights Off Auto Lights Headlights HEADLIGHTS AND FOG LIGHTS Pull the lever toward you. NOTE: To turn off high beam, pull the lever towards you. PUSH

Quick Reference Guide I 08 07 I Quick Reference Guide KONA HYUNDAI 1. Tachometer 2. Speedometer 3. Engine Coolant Temperature Gauge 4. Fuel Gauge 5. Warning and Indicator Lights 6. LCD Display (Including Trip Computer) 2 2 INSTRUMENT CLUSTER Type A Type B 3 4 5 5 5 6 1 1 1 3 4 5 6 HEAD-UP DISPLAY 55 65 SPEED LIMIT 55 MPH The Heads-Up display is a feature that allows the driver to view information projected onto a transparent screen while still maintaining direct view of the road ahead. To activate the Heads-Up Display, press the HUD button on the dash panel located on the left-hand side of the driver. Head-Up Display information 1. Turn-by-turn (TBT) navigation information 2. Road information 3. Driving speed information 4. Cruse control system SET indicator 5. Lane Keeping Assist (LKA) information 6. Blind Spot Collision warning indicators 7. Warning lights 8. Multimedia information 1 2 3 4 5 6 7 8 NOTE: : If you wear polarized sunglasses, it is difficult to read the Head Up Display information.

Quick Reference Guide I 10 09 I Quick Reference Guide KONA HYUNDAI WARNINGS AND INDICATORS Seat Belt Warning Light Charging System Warning Light Air Bag Warning Light Low Tire Pressure Warning Indicator/ TPMS Malfunction Lamp ABS Warning Light Front Fog Indicator Light Electric Power Steering System Warning Light Parking Brake & Brake Fluid Warning Light Engine Oil Pressure Warning Light Malfunction Indicator ESC (Electronic Stability Control) Indicator Low Fuel Level Warning Light ESC (Electronic Stability Control) OFF Indicator Cruise SET Indicator Turn Signal Indicator Light ON Indicator Electronic Brake Force Distribution (EBD) System Warning Light Cruise Indicator Lane Departure Warning System (LDWS) Indicator SPORT mode Indicator Immobilizer Indicator Automatic Emergency Braking (AEB) Warning Light All Wheel Drive (AWD) Warning Light Headlight Warning Light Downhill Brake Control (DBC) Indicator Light Master Warning Light WARNINGS AND INDICATORS High Beam Indicator / Auto headlamps High Beam Assist All Wheel Drive (AWD) LOCK Indicator Light INSTRUMENT PANEL ILLUMINATION Press + or - to adjust the illumination brightness of the instrument cluster. Modes Symbol Description Trip Computer Displays the most recent driving information including average fuel economy, trip, odometer, average speed, etc. Turn BY Turn (TBT) Displays turn-by-turn directions in the LCD cluster with navigation. LKA Displays the state of the Lane Keeping Assist (LKA). Audio Displays the state of the Audio System. Information Displays the service interval and warning messages. User Settings Changes the settings. or LCD DISPLAY MODES or LCD DISPLAY CONTROL 1 : MODE button for changing modes 2 : MOVE switch for changing items 3 : SELECT / RESET button for setting or resetting the selected item 2 3 1

Quick Reference Guide I 12 11 I Quick Reference Guide KONA HYUNDAI Changes the direction of the air flow as following: MODE SELECTION Face Level Bi-Level Floor Level Floor / Defrost Level Defrost-Level Press to activate / deactivate the rear defroster and heated outside mirrors. REAR WINDOW DEFROSTER AND HEATED OUTSIDE MIRRORS MAX A/C MODE 1. Fan Speed Control Knob 2. Temperature Control Knob 3. Mode Select Dial 4. Front Windshield Defrost Dial Position 5. Rear Window Defroster Button 6. Air Intake Control Button 7. A/C (Air Conditioning) Button The MAX A/C automatically selects the A/C, recirculated air, and face level vents. This helps to cool the cabin down more quickly. Select normal A/C after initial cool down to resume fresh airflow and maintain efficiency. AIR INTAKE CONTROL Recirculated air position (Indicator light ON) Outside (fresh) air position (Indicator light OFF) MANUAL CLIMATE CONTROL DEFROSTING / DEFOGGING 2. Set the temperature control to the warmest setting. 3. Set the fan speed to the medium speed. 1. Select the front windshield defrost mode. NOTE: To reduce the tendency of the glass to fog up and also to improve visibility, keep the surface of the windshield clean by wiping it occasionally with glass cleaner and a clean cloth. In addition, select air intake control to the outside (fresh) air position whenever possible while operating the vehicle. 5 7 1 2 6 3 4

Quick Reference Guide I 14 13 I Quick Reference Guide KONA HYUNDAI 1 Temperature Control Knob 2 AUTO (Automatic Control) Button 3 OFF Button 4 Fan Speed Control Knob 5 Mode Selection Button 6 Air Conditioning Button 7 Front Windshield Defroster Button 8 Rear Window Defroster Button 9 Air Intake Control Button AIR INTAKE CONTROL Recirculated air position (Indicator light ON) Outside (fresh) air position (Indicator light OFF) MODE SELECTION Changes the direction of the air flow as following: Floor & Defrost Face Level Bi- Level Floor Level AUTOMATIC HEATING AND COOLING 1. Press the AUTO button. 2. Set the temperature control to the desired setting. The modes, fan speeds, air intake and air conditioning will be controlled automatically according to the temperature setting. SYSTEM OFF MODE Pressing the OFF button will turn the automatic climate control system off. • The fan will turn off. • The outside (fresh) air position will be selected. • The vented air temperature will be at the last temperature setting. + - + - + - Press to activate / deactivate the rear defroster and heated outside mirrors. REAR WINDOW DEFROSTER AND HEATED OUTSIDE MIRRORS NOTE: To reduce the tendency of the glass to fog up and also to improve visibility, keep the surface of the windshield clean by wiping it occasionally with glass cleaner and a clean cloth. In addition, select air intake control to the outside (fresh) air position whenever possible while operating the vehicle. NOTE: It is recommended to use the AUTO function with 72°F temperature set point for optimum comfort and efficiency. AUTOMATIC CLIMATE CONTROL + - 2 3 4 5 9 6 7 8 1 DEFROSTING / DEFOGGING 3. Set the fan speed to the medium setting. 2. Set the temperature control to the warmest setting. 1. Press the front windshield defroster control. + -

15 I Quick Reference Guide KONA HYUNDAI STEERING WHEEL AUDIO CONTROL 1 VOLUME Raises or lowers the speaker volume. 2 SEEK / PRESET Changes the station. 3 MODE Changes the audio source. 4 MUTE Press to Mute. MUTE MUTE MUTE 2 2 3 3 1 1 Type A Type B 4 4 BLUETOOTH PHONE PAIRING 1. Press the SETUP A button. 2. Press the “Bluetooth” button on the screen. 3. Press “Add New” button on the screen. 4. Search for the device name as displayed on your mobile phone and connect. 5. If necessary, input the passkey displayed on the Audio screen. 6. Pairing is complete. NOTE : Vehicle must be parked to complete the pairing process. SEEK RADIO MEDIA TUNE FILE ENTER SETUP PHONE HOME TRACK A To switch between phones: 1. Push the ‘Setup’ button. 2. Select Bluetooth. 3. Select Bluetooth Connections. 4. Select Connect next to the desired phone. BLUETOOTH OPERATIONAL TIPS To Answer a Call: • Press the button on the steering wheel. To Reject a Call: • Press the button on the steering wheel. To Adjust Ring Volume: • Use the VOLUME buttons on the steering wheel. To Transfer a Call to the handset (private mode): • Press and hold the button on the steering wheel until the audio system transfers a call to the phone. To Finish a Call: • Press the button on the steering wheel. In the following situations you or the other party may have difficulty hearing each other: 1. Keep the Bluetooth volume low. High level volume may result in distortion and echo. 2. When driving on a rough road, high speeds and/or with the window open. 3. When the air conditioning vents are facing the microphone located at the headliner and/or when the air conditioning fan is at the max speed. Steering wheel bluetooth control 1 TALK Activates the voice recognition. 2 CALL Places and transfers calls. 3 END Ends calls or cancels functions. MUTE MUTE 2 2 3 1 1

17 I Quick Reference Guide KONA HYUNDAI Making a call using voice recognition: The menu tree identifies available voice recognition Bluetooth® functions. Calling by Name: 1. Press the button. 2. Say the following command: • “Call ”: Connects the call to John. • “ Call : Connects the call to John’s Mobile, Home, or at Work phone number. Dialing by Number: 1. Press the button. 2. Say “Dial Number”. 3. Say the desired phone number. For the complete list of commands, please refer to your Owner’s Manual. VOICE RECOGNITION Your vehicle may be equipped with a Voice Recognition technology which allows drivers to operate their phones without having to take their eyes off of the road to minimize distractions. Voice recognition performance may be affected if driving with windows and sunroof open; when the heating-cooling system is on; when passing in a tunnel or when driving on rugged and uneven roads. Quick reference on using voice commands: To start a voice command, press the button, the following commands are available: Command Function More Help Provides guidance on commands that can be used anywhere in the system. Help Provides guidance on commands that can be used within the current mode. Calls Calls saved in Contacts. Ex) Call “John” Dial Call can be made by dialing the spoken numbers. Ex) Call “123” Phone Provides guidance on Phone related commands. After saying this command, say “Call History”, “Contacts” to execute the corresponding functions. Contacts (Call by Name) Displays the Contacts screen. After saying this command, say the name of a contact saved in the Contacts to automatically connect a call. Dial Number Displays the Dial number screen. After saying this command, you can say the number which you want to call. Navigation Find address in < house #, Street name, City>. Example: “1-0-5-5-0 Talbert Avenue, Fountain Valley Find Find Starbucks Voice Recognition Tips BLUE LINK TELEMATICS SYSTEM • SOS • Navigation • Blue Link Press the button for access to the voice-response menu of services. - Press the button for Destination Search. - Command: Find . Example: “Find Starbucks”. - Press the button for SOS Emergency Assistance. - Refer to your Blue Link User’s Manual for detailed information on system operation. - For immediate assistance with subscription services, please call 1-855-2BLUELINK (1-855-225-8354). You can say: - "Service Link" to schedule a service appointment. - "Roadside Assistance" for roadside services. - "Blue Link Account Services" for help with your Blue Link subscription.

19 I Quick Reference Guide KONA HYUNDAI You can download the Blue Link mobile app to your compatible smart phone from the following sites: • iPhone ® — Apple ® App Store • Android ® — Google Play Remote Start enables you to remotely start your vehicle from virtually anywhere. For navigation vehicles, you can also enable climate control remotely and turn on the rear-window defroster, ensuring a warm or cool car is ready to go when you are. • To use this feature, you must have a Blue Link Personal Identification Number (PIN). To create or change your PIN, log on to www.MyHyundai.com. Remote Start • Remote Start with Climate Control will automatically shut off after 10 minutes or after selected engine timer runs out in navigation vehicles. • While this feature is active, the parking lights will blink until vehicle is turned off or when vehicle is in operation. • To continue operation of the vehicle, the proximity key must be inside the vehicle with the driver prior to pressing the brake and being able to move the gearshift from the P (Park) position. Remember: Preconditions: • Ignition is OFF • Alarm is armed (i.e., vehicle locked by key fob Remote Door Lock) • Gearshift level is in the P (Park) position • Brake pedal is not depressed • Engine hood is securely closed • All the doors are closed and locked • The tailgate or trunk lid is closed • The security/panic system is not activated • The proximity key is not inside the vehicle • The battery power is not low • Vehicle is located in an open area • It has been less than 4 days since last vehicle ignition off • Vehicle located in area with good cell reception Remote Start will terminate: • After 10 minutes or after selected engine timer runs out in navigation vehicles • Brake is pressed without proximity key inside vehicle • Alarm is triggered without proximity key inside vehicle • Door/trunk is opened from inside the vehicle Notice: Laws in some communities may restrict the use of the features that remotely start the engine. For example, some laws may require a person using the remote start feature to have the vehicle in view when doing so or limit the length of time a vehicle engine may idle. Please check local and state regulations for any requirements and restrictions on remote starting of vehicles and engine idling time. WARNING! Do not remote start vehicle in an enclosed environment (i.e., closed garage). Prolonged operation of a motor vehicle in an enclosed environment can cause a harmful build-up of carbon monoxide. Carbon monoxide is harmful to your health. Exposure to high levels of carbon monoxide can cause headaches, dizziness or in extreme cases unconsciousness and/or death. Do not leave children or animals unattended in a vehicle while using the remote start function. CAUTION! If the vehicle’s windshield wipers are left on when the vehicle was last driven, then the wipers will turn on if the remote start function is activated. To avoid damage to the wiper blades (i.e., due to heavy ice or snow accumulated on the windshield), please always turn the vehicle’s windshield wipers off when parking the vehicle. NOTE : Remote Vehicle Start is only available for Push Button Start equipped vehicles with an Automatic Transmission or a Dual Clutch Transmission (DCT).

21 I Quick Reference Guide KONA HYUNDAI RADIO MODE Display Audio Setting the custom button *SiriusXM® is only available on Display Audio Light and Navigation SEEK RADIO MEDIA TUNE FILE ENTER SETUP NAV MAP TRACK VOL PWR PUSH NOTE : A clear view of the southern sky helps to ensure SiriusXM®* radio reception. • SETTING PRESET BUTTONS (FM/AM/SXM) Six preset frequencies for each radio modes can be stored manually. 1. Select the radio mode you want to store a station into. 2. Select the desired station. 3. Touch and hold one of the preset buttons until audible beep is heard. • ADJUSTING THE SOUND CONTROL 1. Press SETUP button and press the sound button on the display. 2. To adjust the Fader/Balance, select the on-screen tab. Touch the on-screen arrows to adjust the desired setting for front, rear, left, or right balance. 3. To adjust the Bass/Midrange/Treble, select the on-screen tab. Touch the on-screen arrows to adjust the tonal sound settings to the desired level. Press POWER button to turn radio on. • TUNING/LISTENING TO CHANNELS 1. Press RADIO button . 2. Rotate TUNE knob to desired channel. NAVIGATION Basic features on the map screen 1 Move to the Home Screen 2 Change the map view mode 3 Voice Guidance On/Off 4 Zoom in the map 5 Set the zoom level automatically according to the guidance 6 Zoom out the map 7 Quick and easy selection of a destination and options 8 Touch to scroll the map 9 Start Guidance 10 Route Options 11 Save frequently used address to address book 12 Find a POI (Point of Interest) around the current position 13 View the vehicle’s current position on the map screen 1 13 8 9 10 11 12 2 3 4 5 6 7 Destination search screen 1 Address : Set destination by address search. 2 Previous destinations : Select from previously inputted addresses and POIs. 3 Online Search: Runs online search. 4 POI categories : Select the desired item in the sub- categories. 5 Gas stations : Select the desired destinations among the searched gas stations. Press [NAV] button in the navigation head unit, and finds a destination by using the [Destination] menu. 2 3 4 1 5 6 7 8 9 6 Restaurants : Select the desired destination among the searched restaurants. 7 Emergency : Select the desired destination among the searched emergency facilities. 8 Address Book : Search the destination with the address book. 9 Coordinates : You can find a destination by entering the coordinates of latitude and longitude. E You can choose a specific feature to be accessed when the Custom button E is pressed. To set the feature associated with the Custom Button, choose the feature in the Setup Menu.

23 I Quick Reference Guide KONA HYUNDAI AUX AND USB PORT Use the Aux input jack to connect an external audio device. Use the media USB port to connect a USB device with music files or to access features on your smartphone using Apple CarPlay or Android Auto phone projection. Use the charging USB port to charge an external device such as a cell phone WIRELESS CELLULAR PHONE CHARGING SYSTEM NOTE: The wireless cellular phone charging system supports only the Qi-enabled cellular phones ( ). NOTE: Do not place any metallic items such as coins, keys on the charger. Avoid putting credit cards, etc. on the charger as they might get damaged by the magnetic field. There is a wireless cellular phone charging system inside the front console. The system operates with all doors closed, and the ignition switch is in the ACC/ON position.

25 I Quick Reference Guide KONA HYUNDAI CAR SETUP 1. Press the SETUP button on the radio. 2. Touch the “Phone Projection” icon on screen. 3. Select “On” for Android Auto. 4. Connect your Android phone to the vehicle USB port. Agree to the notification and disclaimers on your phone then the “Android Auto” icon will appear confirming the setup. For more detailed information on how to operate Android Auto, please refer to your navigation manual. For additional Android Auto support, please refer to the Android Auto Support Website https://support.google.com/androidauto/ Android Auto, Google Play, Android, and other marks are trademarks of Google Inc. PHONE SETUP Turn on Bluetooth® on your phone and connect the micro USB cable to your phone and the USB port on the vehicle. Phone will prompt you to download the Android Auto app and update other needed apps (i.e. Google Maps™, Google Play Music™, Google Now™). NOTE: Vehicle must be parked. - Location mode setting should be set to High accuracy. - Car and phone setup should be completed in one sitting. If phone setup needs to be resumed, recommend to Force Stop the Android Auto app on the Phone then reopen the app and accept the Disclaimer notifications. REQUIREMENTS: - Micro USB cable - OS Android™ 5.0 or higher - Compatible Android Phone - Data and wireless plan for applicable features BEFORE YOU BEGIN: - Android Auto features may operate differently than on your phone. - Message and data charges may apply when using Android Auto. - Android Auto relies on the performance of your phone. If you experience performance issues: - Close all apps and then restart them or - Disconnect and then reconnect your phone - Using the micro USB cable that was provided with your phone is recommended. - When Android Auto is active, your in-vehicle voice recognition system is disabled and you will be using talk to Google™ to make your requests. ANDROID AUTO SUPPORT https://support.google.com/androidauto/ ANDROID AUTO ™

27 I Quick Reference Guide KONA HYUNDAI CAR SETUP 1. Press the SETUP button. 2. Touch the “Phone Projection” icon on the screen. 3. Touch “iOS” on the Phone Projection Settings screen then touch “On” to enable Apple CarPlay. 4. Connect your Apple iPhone to the vehicle USB port then touch ‘OK’ when the pop-up message appears. The Apple CarPlay icon will now appear on the vehicle Home screen confirming the setup. Apple CarPlay, Apple, and other marks are trademarks of Apple Inc. REQUIREMENTS - Apple Lightning® cable - Latest iOS - iPhone® 5 or above - Data and wireless plan for applicable features BEFORE YOU BEGIN - Apple® CarPlay features may operate differently than on your phone. - Message and data charges may apply when using Apple CarPlay. - Apple CarPlay relies on the performance of your phone. If you experience performance issues: - Close all apps and then restart them or - Disconnect and then reconnect your phone - Using the Apple Lightning cable that was provided with your phone is recommended. - When Apple CarPlay is active, your voice recognition system is disabled and you will be using Siri® to make your requests. APPLE CARPLAY ™ PHONE SETUP On your phone, go to Settings > General > Restrictions > CarPlay to allow CarPlay access. On your phone, go to Settings > General > Siri and ensure Siri is turned ON.

29 I Quick Reference Guide KONA HYUNDAI PHONE Touch the PHONE 5 icon to access the Phone screen. Siri will automatically asks ‘Who you would like to call’ when the PHONE 5 icon is selected. NOTE: Phone call sound quality is dependent on the wired connection. Using the Lightning cable that came with the phone is recommended. APPLE MUSIC Touch the APPLE MUSIC 6 icon to access the Apple Music screen. APPLE MAPS Touch the APPLE MAPS 7 icon to access the Apple Map screen. MESSAGES Touch the MESSAGES 8 icon to access the Message screen. Siri will automatically asks ‘To hear unread messages or create a new one’ when the MESSAGE icon is selected. 3rd PARTY APPS Supported CarPlay apps that are downloaded on your phone will appear on the CarPlay screen. Touch the apps icons to access those supported apps. NOTE: A list of the supported CarPlay supported apps can be found at http://www.apple.com/ios/carplay/ Ensure phone has latest version of the 3rd Party Apps. Apple CarPlay uses Siri to perform many actions like sending messages, placing calls, and looking up/setting POI/Destinations. A Siri session can be initiated on any screen by: 1. Touch and holding the HOME icon 1 on the CarPlay screen or 2. Press the steering wheel VOICE RECOGNITION 13 button. Note: Ensure Siri feature is set to ON in your phone (Go to Settings > General > Siri). 3. Say any of the following commands; •“Text ‘Call you later’” to send a text message. •“Read text messages” to read available text message. •“Call ” to make a phone call. •“Find ” to locate a POI/Destination. CarPlay Home Screen SIRI 1 HOME ICON 2 WIRELESS CONNECTIVTY 3 CELLULAR SIGNAL 4 PHONE TIME 5 PHONE 6 APPLE MUSIC™ 7 APPLE MAPS 8 MESSAGES 9 3RD PARTY APPS 10 SCREEN PAGE INDICATOR 11 EXIT TO HYUNDAI 12 CURRENT CARPLAY AUDIO PLAYING 2 3 4 1 5 6 7 8 9 10 11 12 13

31 I Quick Reference Guide KONA HYUNDAI DOWNHILL BRAKE CONTROL (DBC) The Downhill Brake Control (DBC) helps the driver maintain a slow speed on a steep downhill without depressing the brake pedal. The system automatically applies the brakes to keep the vehicle speed under 5 mph. NOTE: When activated, the speed of the vehicle will be reduced. Please refer to your Owner’s Manual for further information. TIRE PRESSURE MONITORING SYSTEM (TPMS) LOW TIRE PRESSURE INDICATOR Illuminates if one or more of your tires are significantly under-inflated. TPMS MALFUNCTION INDICATOR Blinks for approximately one minute, then remains illuminated when there is a malfunction with the TPMS. Inspect all tires and adjust the tire pressure to specification. If the lamp remains illuminated, “we recommend the vehicle be checked by an authorized HYUNDAI dealer. LOW TIRE PRESSURE / TIRE PRESSURE MONITOR / TPMS MALFUNCTION DISPLAY(LCD DISPLAY) Low Tire Pressure / Tire Pressure Monitor / TPMS Malfunction Display (shown on the cluster LCD display) Low Tire Pressure Indicator / TPMS Malfunction Indicator Select the Assist mode by pressing the mode button on the steering wheel to display tire pressure. Tire pressures will display after driving a short distance. If a tire pressure drops lower than predetermined specification, the Low Tire Pressure Indicator will illuminate and the cluster display will indicate tire(s) requiring air.

33 I Quick Reference Guide KONA HYUNDAI DRIVE MODE DRIVE MODE Sport mode focuses on dynamic driving by controlling the steering wheel effort, and engine / transmission performance. Sport mode NORMAL mode is not displayed on the instrument cluster. NORMAL mode DRIVE MODE INTEGRATED CONTROL SYSTEM You can select the DRIVE mode according to your preference or the road condition. The system defaults to NORMAL mode each time you start your vehicle. Each time you press the button, the drive mode changes as follows : Normal Sport DRIVE MODE During off-road or inclement weather conditions, press the AWD LOCK switch to drive in full-time AWD. This will divide the power between the front and rear wheels (only when the vehicle speed is under 19 mph). The AWD LOCK indicator light on the instrument cluster will illuminate. AWD LOCK The Lane Keeping Assist (LKA) uses the front camera to monitor the lines on the road. In case of an unintended lane departure, it will warn the driver and can appl y counter steering torque to guide the car back to the center of the lane. To adjust the settings of LKA, select the LKA sub menu in the LCD cluster display under User Settings. LANE KEEPING ASSIST (LKA) BLIND SPOT COLLISION WARNING (BCW) The BCW (Blind-Spot Collision Warning) system uses a radar sensor to alert the driver while driving. The system monitors the rear area of the vehicle and provides information to the driver. The system incorporates the following functions: 1 Blind-Spot Collision Warning (BCW) 2 Lane Change Assist (LCA) 3 Rear Cross-Traffic Collision Warning (RCCW)– in reverse gear under 6 mph • To turn on the BCW, press the BCW button (indicator illuminated). • To turn off the BCW, press the BCW button again. The BCW and LCA systems will activate once the vehicle speed exceeds 20 mph. The RCCW system activates in reverse gear under 6 mph. • To turn on the LKA, press the LKA button. • To turn off the LKA, press the LKA button again. 2 3 1

35 I Quick Reference Guide KONA HYUNDAI The Forward Collision Avoidance (FCA) system is designed to detect and monitor the vehicle ahead and warn the driver if a collision is imminent. On vehicles equipped with both camera and radar sensor, pedestrian detection is also available. To operate the system, select the FCA (Forward Collision Avoidance Assist) sub menu in the LCD cluster display under User Settings. Please refer to your Owner’s Manual for further information. FORWARD COLLISION-AVOIDANCE ASSIST (FCA) Please refer to your Owner's Manual for more information. CRUISE CONTROL/SMART CRUISE CONTROL 2 3 1 4 Setting Vehicle Distance (Smart Cruise Control only) The Cruise Control system allows you to program the vehicle to maintain a constant speed without holding the accelerator pedal. 1 2 This system assist you in setting the distance from the vehicle ahead and will maintain the selected distance without you depressing the accelerator or the brake pedal. 1 To turn On/Off cruise control. 2 Toggle switch UP to Resume or Increase the cruise control speed. 3 Toggle switch DOWN to Set or Decrease the cruise control speed. 4 To Cancel the Cruise Control. Press the button to set and maintain the vehicle-to-vehicle distance without pressing the accelerator or brake pedal. The vehicle-to-vehicle distance 1 will automatically activate when you set the cruise speed 2 . Each time the button is pressed, the vehicle- to-vehicle distance changes as follows: Distance 2 Distance 3 Distance 4 Distance 1 Setting Cruise Control 1. Press the “CRUISE” button 1 to turn on Cruise Control. The icon will illuminate in the instrument cluster. 2. Toggle “-SET” switch (3) DOWN to set cruising speed. Adjusting the vehicle speed 1. Toggle “+RES” switch 2 UP to increase cruising speed. 2. Toggle “-SET” switch 3 DOWN to decrease cruising speed. Note: Quick toggle up/down will change speed by 1 mph. Holding switch up/down will change speed by 10 mph. To Cancel Cruise Control Press the “CANCEL” button 4 or depress the brake pedal.

37 I Quick Reference Guide HYUNDAI KONA CUSTOMER DELIVERY CHECKLIST HYUNDAI OWNER DEALERSHIP NAME SALES CONSULTANT DATE VIN PREVIOUS VEHICLE BEFORE DELIVERY BLUETOOTH® HANDS-FREE SWITCHING BETWEEN PAIRED PHONES On the radio: 1. Push the SETUP button. 2. Select Bluetooth. 3. Select Bluetooth Connection . 4. Select Connect next to the desired phone. CONNECTING YOUR PHONE On the radio: 1. Push the SETUP button. 2. Select Bluetooth. 3. Select Bluetooth Connection . 4. Select Add New. In your phone’s Bluetooth settings: 5. Select the on your phone. 6. Enter the passkey from the radio or accept the authorization pop-up on your phone. For more information, visit HyundaiBluetooth.com Using Voice Command: “Change Bluetooth device” BLUETOOTH® HANDS-FREE SWITCHING BETWEEN PAIRED PHONES On the radio: 1. Push the SETUP button. 2. Select Bluetooth. 3. Select Bluetooth Connection . 4. Select Connect next to the desired phone. CONNECTING YOUR PHONE On the radio: 1. Push the SETUP button. 2. Select Bluetooth. 3. Select Bluetooth Connection . 4. Select Add New. In your phone’s Bluetooth settings: 5. Select the on your phone. 6. Enter the passkey from the radio or accept the authorization pop-up on your phone. For more information, visit HyundaiBluetooth.com Using Voice Command: “Change Bluetooth device” ☐ REVIEW QUICK REFERENCE GUIDE ☐ PAIR CUSTOMER'S PHONE TO THE BLUETOOTH SYSTEM (if equipped) ☐ OPERATION OF THE NAVIAGATION SYSTEM (if equipped) - page 22 ☐ REVIEW AND TEAR OFF VOICE COMMAND ☐ OPERATION OF THE AUDIO SYSTEM - page 21 WALK THE CUSTOMER THROUGH EACH OF THE FOLLOWING KEY DELIVERY FEATURES ☐ SET TIRE PRESSURE LF RF RR LR ☐ VERIFY VEHICLE IS CLEAN, IN GOOD CONDITION, FREE OF CHIPS AND SCRATCHES · CLEAN WINDSHIELD AND BACK WINDOW ☐ ENSURE FLOORMATS ARE SNAPPED INTO PLACE ☐ TIRE PRESSURE MONITORING SYSTEM (TPMS) - page 31 Explain TPMS function to customer. - When illuminated, one or more tires are under-inflated. - Blinks for approximately one minute then remains illuminated when there is a malfunction with the TPMS. - You can also check the individual tire pressures in the Information Display mode in the LCD cluster. Tire pressures are displayed in the cluster after a few minutes of driving. MEMO 0 0 10 1 2 3 4 5 6 20 30 40 50 60 70 80 min 2.2 bar/ 32 psi 0 10 80 90 0 10 20 30 40 50 60 70 80 90 or E N G I N E START STOP 3 2 1 0 max80 km/h max50 mph 0 0 10 1 2 3 4 5 6 20 30 40 50 60 70 80 Recheck Tire Pressure 1. Screw the compressor hose directly to the tire valve. 2. Insert the compressor power plug into the vehicle’s power outlet. 3. Adjust to the recommended tire pressure located on the driver side door jamb placard. To increase the tire pressure: 1. Switch ON the compressor. 2. To check the current tire pressure, briefly switch OFF the compressor. To reduce the tire pressure: 1. Loosen the knob on the gauge. Tighten the knob to set tire pressure. NOTE: A compact spare tire accessory may be available. Please consult your nearest authorized Hyundai dealer. 0 0 10 1 2 3 4 5 6 20 30 40 50 60 70 80 min 2.2 bar/ 32 psi 0 10 20 30 40 50 60 70 80 90 max80 km/h max50 mph 0 0 10 1 2 3 4 5 6 20 30 40 50 60 70 80 0 0 10 1 2 3 4 5 6 20 30 40 50 60 70 80 min 2.2 bar/ 32 psi 0 10 20 30 40 50 min 2.2 bar/ 32 psi 60 70 80 90 0 10 20 30 40 50 60 70 80 90 or E N G I N E START STOP 3 2 1 0 max80 km/h max50 mph 0 0 10 1 2 3 4 5 6 20 30 40 50 60 70 80 TIRE MOBILITY KIT Setup 1. Remove the speed restriction label from the sealant bottle and place it on the center of the steering wheel. 2. Ensure that the compressor is switched to OFF. 3. Lift the cable cover and screw the compressor hose on to the connector of the sealant bottle. 4. Insert the sealant bottle into the housing slot of the compressor. Immediately drive 4-6 miles to evenly distribute the sealant in the tire. 5. Screw the filling hose of the sealant bottle onto the tire’s valve stem. 6. Insert the compressor power plug into the vehicle’s power outlet. 7. Turn the ignition switch to the ON position or press the Engine Start/ Stop button twice. Inflate Tire 1. Switch ON the compressor and let it run for approximately 5 minutes. 2. Switch OFF the compressor and check to ensure that inflation pressure is over 32 psi. If not, the puncture is too large to repair. Contact Hyundai Roadside Assistance. 3. Remove the filling hose , compressor hose , and compressor power plug . 0 0 10 1 2 3 4 5 6 20 30 40 50 60 70 80 min 2.2 bar/ 32 psi 0 10 20 30 40 50 min 2.2 bar/ 32 psi 60 70 80 90 0 10 20 30 40 50 60 70 80 90 or E N G I N E START STOP 3 2 1 0 0 0 10 1 2 3 4 5 6 20 30 40 50 60 70 80 Scan to view a video of: Tire Mobility Kit