Element E3 F Series Installation Instructions Manual

920E3 - - HMH AIC FL Round or Square Type IC Adjustable Housing with Toroidal Transformer for Flanged Trims E3_F_- HAIM_ 1.5 HALOGEN MR 16 - ROUND SQUARE FLANGED / G P I : ENERAL RODUCT NFORMATION This product can be dimmed with a low-voltage magnetic dimmer. For insulation applications above R25,no branch circuits allowed. This instruction shows a typical installation. 1 HOUSING CLASP HOUSING 1B INNER ADJUSTABLE BAR OUTER ADJUSTABLE BAR TAB STOP POINT 3 3 NAIL 2 Slide the inner adjustable bar completely through the three housing clasps.Make sure the nail is on top. Slide and push the outer adjustable bar completely onto the inner adjustable bar so that the tab clicks into place behind the stop point.This will prevent the adjustable bars from coming apart. Repeat steps 2 & 3 for the other side of the housing. 2 3 4 Install the Housing with Adjustable Bars 1A BREAK OFF AND DISCARD ¾” or thicker ½” to ¾” LEAVE TAB IN PLACE Keep Tab for ceiling ½”to ¾”thick. When using adjustable hanger bars with ½”to ¾”thick ceilings,leave the tab of the hanger bars in place. Break off Tab for ceiling ¾”or thicker. When using adjustable hanger bars with ¾”or thicker ceilings,remove the tab by bending it at the perforation. 1 NOTE: Skip this section if installing the housing with butterfly brackets. CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90°c supply conductors.

NOTCH 8 TRIM HOLDER HOUSING Adjust the trim holder position (horizontal position) by sliding the housing on adjustable bars. When the desired location is achieved,tighten the two #6 self tapping screws to lock the housing onto the adjustable bars. 7 8 NOTE: Notches in trim holder can be used to align multiple housings using a laser or string. 8 1C TRIM HOLDER NAIL JOIST 6 6 5 NOTE: The adjustable bars can be mounted to joists that are spaced 16" - 24" apart. Align the bottom of the end plates with the bottom of the ceiling joists. Level the adjustable bars and,with a hammer,tap the nails completely into the joists to secure the adjustable bars in place. 5 6 5 6 1D ADJUSTABLE BAR 7 TRIM HOLDER NOTCH HOUSING

3A Push the tab on the housing electrical box up and remove the electrical box cover. 1 BUTTERFLY BRACKET TRIM HOLDER WING NUT 1 2 NOTE: Notches in trim holder can be used to align multiple housings using a laser or string. NOTCH Install the Housing with Butterfly Brackets 2A Slightly loosen the wing nut to slide the butterfly bracket up or down. After achieving the proper location,tighten the wing nut to secure the butterfly bracket in place. Repeat steps 1 and 2 on for the other butterfly bracket. Utilize the butterfly brackets to install the housing in accordance with local electrical codes. 1 2 3 4 NOTE: Notches in trim holder can be used to align multiple housings using a laser or string. NOTE: Skip this section if installing the housing with adjustable bars. 3B Install the conduit to the housing electrical box. 2 WARNING: RISK OF FIRE: When using the housing electrical box for power feed through, use 4 - #12 ,or 6 - #14 branch MAX AWG AWG circuit wires. CONDUIT 2

3C Run the power line wires into the housing electrical box. Connect the neutral power line wire to the white transformer wire with a wire nut. If using a dimmer,connect the hot power line wire to the yellow transformer wire with a wire nut.Make sure that the black transformer wire is disconnected,capped with a wire nut. If using a switch,connect the hot power line wire to the black transformer wire with a wire nut.Make sure that the yellow transformer wire is disconnected,capped with a wire nut. Make sure that housing is grounded in accordance with local electrical codes. Replace the electrical box cover.Make sure that the top edge of the cover snaps under the tab. 3 4 5a 5b 5b 5a 5a 5b 6 4 4 6 6 7 4A For round trims,mark a 3-7/8" diameter circle on drywall. Cut out the marked section. For square trims,mark a 3-7/8" square on drywall.Cut out the marked section. 1 3-7/8" 3-7/8" ROUND TRIM HOLDER SQUARE TRIM HOLDER Align the cut out section of drywall with the trim holder and install the drywall. 2 2 DRYWALL TRIM HOLDER JOIST 4B

To install a lens accessory (optional),unscrew the snoot from the lamp cartridge. Place a maximum of three accessories into the lamp cartridge. Replace and tighten the snoot completely to the lamp cartridge. 2 1 To release the lamp cartridge,rotate it counter clockwise and gently pull out the assembly. 5B LAMP CARTRIDGE SNOOT LENS ACCESSORIES 3 4 3 Unscrew the lamp cartridge base from the lamp cartridge. Pull out the socket from the lamp housing and feed it through the lamp base. Push the lamp pins completely into the socket holes. Place the lamp into the lamp cartridge and reinstall the lamp cartridge base and firmly tighten. 5 Use Watt Type 16 Halogen MAX 50 MR Lamp. 6 LAMP SOCKET 5C LAMP CARTRIDGE LAMP CARTRIDGE BASE 9 Feed the socket wire sleeve back into the lamp housing and align the lamp assembly with the keyed slots on the lamp housing. Place the lamp assembly into the lamp housing and rotate it until it locks into place. 10 7 8 6 7 5A Low Hi LAMP CARTRIDGE Low Hi Low Hi 5D Low Hi KEYED SLOT LAMP CARTRIDGE SOCKET WIRE SLEEVE LAMP HOUSING

2 To tilt the lamp housing vertically,rotate the tilt adjustment screw until the desired angle is reached. NOTE: Lamp housing can tilt 40° vertically.Lines on lamp housing are 5° apart. NOTE: Lamp housing can rotate 361° horizontally. 3 Pull the rotation lock down to unlock the lamp housing. Rotate the lamp housing horizontally. When the desired position is achieved push the rotation lock up to lock the lamp housing in place. 4 Low Hi 6A NOTE: The location of the height adjustment screw is indicated with the words Low and Hi. HEIGHT ADJUSTMENT SCREW 1 6B 20 40 30 10 0 INDICATOR 1 2 TILT ADJUSTMENT SCREW Low Hi 2 6C ROTATION LOCK Low Hi 1 To adjust the height rotate the height adjustment screw. Adjust upward to minimize glare and flash on the trim or downward for maximum light output and efficiency.

IL 60077 847.410.4400 www.element-lighting.com © 2016 Element Lighting,L.L.C.All rights reserved.The "Element" graphic is a registered trademark of Element.Element reserves the right to change specifications for product improvements without notification. A Generation Brands Company SAVE THESE INSTRUCTIONS!