Moza iFocus Operation & User’s Manual

注意事项： 本说明书仅指导跟焦器电机部分与MOZA Air 2搭配使用的连接使用方法及注意事项，并未 完整说明跟焦器的所有功能。 如需实现更多功能，请搭配遥控器使用。 x1 x1 x1 x1 跟焦器 跟焦环 Mutli-CAN连接线 用户手册 装箱清单 Note: This manual only guides the connecting and using methods and precautions used by the follow focus motor part in conjunction with Moza Air 2, and does not fully describe all the functions of the follow focus. For more functions, please use it with the remote control. Motor Lens Gear Ring Multi-CAN Cable User Manual

Gear Knob: Secures the gear to the motor. Quick Release Mount: Mount the iFocus to a 15mm rod. Multi-CAN Port: Allows the gimbal to communicate with the motor. Antenna USB-C: Used to charge the motor. Status Indicator: Displays the system status and battery level. Power Button: Press and hold for 1 second until the green indicator lights up to power on the motor. Press and hold for 3 seconds until the white indicator lights up to enter firmware grade. Press and hold for 1 second until the red indicator flashes to power off the motor.

a. Fits the lens gear ring with your camera lens. b. Tighten the clip. a. Loosen the knob(1) on the quick-release mount and slide the motor onto the support rod(2).Tighten the knob to secure the motor’s position on the support rod. Note: Ensure the clip is tight and that the lens gear ring makes good contact with the lens.You may also use a standard 0.8 Mod lens gear ring of your own. b. Tighten the knob(1) to secure its position. Ensure the motor gear(2) and lens gear ring(3) make good contact. 2. Mount the Motor Getting Started

1. System Status Indicator 2.Charging Charge the iFocus with USB-C. Then LED light turns blue. When fully charging, the light goes off automatically. When connecting iFocus to MOZA Air2 with Multi-CAN cable, Air 2 can charge iFocus. 3.Turn on and turn off Long press the power button for 1 second, and the light turns green. The motor turns on. Long press the power button for 1 second and red light blinks twice. The motor turns off. 4.Route Calibration Mark the total distance of the lens focus ring by route calibration before using the iFocus to avoid rotating the motor over the route of lens focus ring. The motor remembers your last calibration and does not need to be re-calibrated every time it is turned on unless you change the motor position or remount it after the motor has been shut off. The operations of route calibration are as follows: a. Enter the Air 2 menu, and select Advanced>iFocus>Turn off to turn off the iFocus motor. b. Manually rotate the lens to the start point, then select Advanced>iFocus>Start point to confirm the start point. Functions of MOZA iFocus 3. Connect to MOZA Air 2 The description of LED： State LED Description Upgrading Mode White light Firmware Upgrade Mode On Green blinks Bluetooth blinks Remaining capacity over 70% Remaining capacity: 30%~70% Red blinks Battery low Off Blue solid light Charging

a. Connect the iFocus to MOZA Air 2 via Multi-CAN cable. b. Long press the power button for 3 seconds in power off status until the white indicator lights up. c. Follow MOZA Air 2 firmware instruction to upgrade the firmware. d. Restart the iFocus and MOZA Air 2 after the upgrade is complete. Firmware Upgrade Specifications Note: The iFocus motor can be turned on by selecting Advanced > IFocus> turn on during calibration. Note that if the start and end points are not calibrated, the calibration is invalid. Note: Turn down the sensibility level if the iFocus rotates too fast, and turn the level up it if the iFocus rotates too slowly. c. Manually rotate the lens to the end point, then select Advanced>iFocus>End point to confirm the end point. The iFocus motor will start automatically. 5.Control iFocus movement by Air 2 a. Enter the Air 2 menu, Gimbal Set>Operations>Wheel>Function>Focus-1 or Focus-2 to select the wheel to control the follow focus. You could also press the Mode button on the Air 2 until the wheel mode on the screen turns to Foucs-1 or Focus-2 mode. b. Rotate the wheel to control the motion of iFocus 6.iFocus Control Sensibility Settings Enter the Air 2 menu, and select Gimbal Set>Operations>Wheel>Sensi to adjust the control sensibility. Weight(battery excluded) 198g Dimensions 115*65*30mm Operating Voltage 7.2V Battery Capacity 600mAh Bluetooth Support Charging Port USB-C

天线 USB-C：给跟焦器充电 状态指示灯：指示跟焦器电量、工作状态等信息 电源键： 关机状态下长按1s，状态指示灯绿灯亮起，跟焦器开机 关机状态下长按3s，状态指示灯白灯亮起，进入升级模式 正常工作或升级模式下长按1s，状态指示灯红灯闪烁后关机

6 1.安装跟焦环 a.用跟焦环围住镜头对焦环，拉紧跟焦环 b.将跟焦环两端的固定结构锁紧 a. 将跟焦器管夹1套入跟焦安装管2，上下调节跟焦器到合适的位置 注意：务必使跟焦环与镜头对焦环卡紧，且转动跟焦环的时候镜头对焦环能同步转动 跟焦环也可安装至光圈环与变焦环，请根据需要选择安装的位置 b. 拧紧跟焦器管夹上的旋钮1，使跟焦器齿轮2与跟焦环3咬合 2-安装跟焦器 安装

1. LED灯状态 2.充电 使用USB-C给跟焦器充电，跟焦器LED灯显示为蓝色，充满后自动熄灭。 当iFocus和MOZA Air2使用时，插上Multi-CAN连接线，跟焦器可以从MOZA Air2取电 3.开机、关机 长按电源键1秒，直到跟焦器亮绿灯，松开按键即可。开机状态下，长按电源键1秒，红色 指示灯闪烁两次，跟焦器关机。 4.行程校准 使用跟焦器前请通过行程校准来标记镜头对焦环的总行程，以避免跟焦器转动超过镜头对 焦环的行程。 跟焦器将记录上一次的校准数据，关机后如果没有使齿轮与对焦环的相对位置发生变化（ 手动转动对焦环或者重新安装跟焦器），就不需要再次进行校准。 行程校准的操作如下： a. 进入Air2菜单，选择Advanced>iFocus>Turn off 关闭跟焦器电机 b. 手动转动镜头到起始位置，然后选择Advanced>iFocus>Start point确认行程起始位置 c. 手动转动镜头到终点位置，然后选择Advanced>iFocus>End point确认行程终点位置， 这时跟焦器电机会自动启动 跟焦器功能 3.连接MOZA Air2 LED灯定义如下： 状态 灯光 含义 升级模式 白灯亮 固件升级模式 开机 绿色闪烁 蓝牙闪烁 剩余电量高于70% 剩余电量30%~70% 红色闪烁 电量不足 关机 蓝色灯常亮 正在充电

级固件。 a. 将跟焦器与Air2通过Multi-CAN线连接 b. 关机状态下长按跟焦器电源开关3s直到LED等显示为白色 c. 按照MOZA Air 2的固件升级操作，进行升级 d. 升级完成后，重启跟焦器和MOZA Air 2即可正常工作 固件升级 规格参数 注意：校准过程中选择Advanced>iFocus>Turn on即可开启跟焦器电机。如果没有 将起点与终点都校准好就启动，则本次校准无效 注意：您在使用时，如果觉得跟焦器转动太快，可以降低跟焦器控制灵敏度；如果觉 得跟焦器转动太慢，可以升高跟焦器控制灵敏度 5.Air2控制跟焦器运动 a. 进入Air2菜单， Gimbal Set>Operations>Wheel>Function>Focus-1或者Focus-2选 择滚轮控制跟焦器。也可以按Air2的M键，直到Air 2屏幕上的手轮模式变为F1或者F2 b. 转动滚轮即可控制跟焦器运动 6.跟焦器控制灵敏度设置 进入Air2菜单，Gimbal Set>Operations>Wheel>Sensi调节控制的灵敏度。 重量（不带电池） 198g 尺寸 115*65*30mm 工作电压 7.2V 电池容量 600mAh 蓝牙 支持 蓝牙充电接口 USB-C