ReelCraft 5600 OLB Operating Instructions
Read Online
Read the ReelCraft 5600 OLB Operating Instructions online using the built-in PDF viewer.
Text of the manual
1. Do not use reel at higher pressures or temperatures than listed on
the back of this bulletin.
2. Remove all spring tension before beginning dissassembly process.
SAFETY
Operating Instructions
Series 5000 Spring Driven Hose Reels
Low Pressure Model Numbers:
Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605
Customer Service: 855-634-9109 • [email protected] • www.reelcraft.com
Form# 581-1091 Rev: 2/2014
Dimensions
A
14 3/8”
B
14”
C
9 3/4”
D
2 1/2”
E
6 1/8”
5600 OLB
INSTALLATION:
A flexible hose connection must be used between the hose reel inlet and the source of supply to prevent possible
misalignment and binding.
LUBRICATION:
Hose reel spring and bearings are factory lubricated and require no further lubrication.
REPLACING HOSE:
1. Wind spool flange clockwise-facing swivel-until spring is tight.
2. Back off three turns and latch.
3. Insert hose through roller guide.
4. Connect hose fitting to swivel joint and secure hose with clamps.
ADJUSTMENTS:
To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is
obtained.
REPAIRS:
Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.
MOUNTING:
The hose reel is equipped with a universal mounting bracket so that it can be mounted on the floor, wall or
ceiling; whichever place is convenient. The hose guide arm can be moved to the position desired by removing
the screws fastening the guide bracket to the reel base. Shift the guide arm bracket so the hose comes off the
reel at the desired position and replace the screws. NOTE: For proper installation in wall mount applications, ensure
reel is mounted with inlet on the right as you are facing the reel. Failing to do so could cause latching issues.
Series 5000 Spring Driven Hose Reels
Page 2
www.reelcraft.com
Specifications
Item #
Part #
# Req.
Description
Item #
Part #
# Req.
Description
Item #
Part #
# Req.
Description
1
300031
2
1” Snap Ring
12
S300011
7
10-32 Hex Lock Nut
23
400020
5
O-ring
2
300034
2
Spacing Washer
13
S504240
1
Drive Spring Assembly
24
S400109
1
Latch Plate Assembly
3
S295-102
3
1/4” Plastite Hex Screw
14
S261360
1
Spring Case Stud
25
300035
1
10-32 x 1” Mach. Screw
4
260022
1
Sheave Flange
15
300006
1
3/8-16 x 1/2” Set Screw
26
3-117440
1
U-bolt
5
500006
1
Sheave Disk
16
S500103
1
Spring Case Assembly
27
261650-1
2
1/4-20 Zinc Nyloc Nut
6
S50019
1
Latch Cam
17
S82-15
1
10-32 x 3/8” Nyloc Nut
28
260227-B
1
Main Shaft
7
S260648
1
Spring Arbor
18
S400021
1
Latch Bumper
29
600374-1B
1
Swivel Assembly
8
300002
2
10-32 x 1/2” Screw
19
S32-136
1
10-24 x 3/8” Mach. Screw
30
S160-3
1
Street Ell
9
1-HR1004A
1
Hose Bumper Assembly
20
S400012
1
Latch Bushing
10
S500107
1
Guide Arm & Roller Assembly
21
S400018
1
Latch Spring
11
500101
1
Base Assembly
22
300001
1
10-32 x 3/8” Screw
Hose I.D. and Length
None
Reel Inlet Connection
3/8” F.P.T.
Max. Operating Pressure
300 P.S.I.
Max. Operating Temperature
210° F
