Morso 7800 Series Instructions For Installation And Use Manual

It harms the environment, and constitutes very poor use of the wood, as the gases in the wood do not ignite at the low temperature, but settle as soot (unburned gases) in the chimney and stove. Extreme conditions, such as poor draught in the chimney, large quantities of wood or wet wood, may, in the worst-case scenario, cause an explosive ignition. When firing in the summer period, when there is minimal need for heat, the combustion will be poor. The stove provides too much heat, so the combustion should be reduced. ...

Discuss the cleaning options with your chimney sweep. If there is insufficient draught in the chimney, it may be a good idea to install the flue pipe straight up, so as to minimise smoke migration in the actual com- bustion chamber. Avoid having any more bends than necessary, and limit the length of the flue pipe so as not to reduce the draught. Fresh air supply A wood-burning stove requires air for combustion. As a result, firing a wood- burning stove will help to create a healthy climate in your house. If the house is very tightly sealed, and particularly if ther ...

3 1.1 Unpacking the stove 3 1.2 Installing the stove 3 1.3 Chimney sweep 3 1.4 Location of the stove/distance requirements 3 1.5 The chimney 5 1.6 Pipe connections 6 1.7 Connecting to a brick chimney 7 1.8 Connecting to a steel chimney 7 1.9 Draught 9 2.0 Firing/using the stove 10 2.1 Lighting instructions and fuelling intervals 11 3.0 Routine stove maintenance 15 3.1 External maintenance 15 3.2 Internal maintenance 15 3.3 Cleaning the stove 16 Additional accessories We offer a comprehensive line of chimney, floor plate and accessory products that can fa- cil ...

wood with a total weight of 1.5-2 kg and a length of 25- 30 cm over the embers in a single layer, with a distance of approximately 1 cm. 6. Open the air supply to maximum, and close the door. The fresh wood will be lit within 1-3 minutes. If it does not light, open the door slightly to allow in en- ough air to ignite the wood. Close the door again once the wood has caught. 7. Reduce the amount of combustion air to the desired position, and the optimal combustion will continue. Make sure that there is always enough air (oxygen) to ...

Description Product no. Cast grate 34791400 Cast smoke hood 34791800 Vermiculite baffle 7900 79790500 Glass window, front 79790100 Glass window, outer side 7900 79790200 Glass window, inner side 7900 79790300 Rear vermiculite brick 7900 79790400 Vermiculite baffle 7800 79791200 Rear vermiculite brick 7800 79791300 Vermiculite side brick, right 7800 79791100 Vermiculite side brick, left 7800 79791000 ...

E-Mail: [email protected] · Website: www.morsoe.com Morsø Jernstøberi A/S - 24.05.2016 - 72797500 IMPORTANT! How to heat safely for the environ- ment and yourself! • Use only dry wood Use only dry (max. 20% moisture content) and untreated wood. The fuel must be split and 8 - 12 cm thick. • Light Light with dry kindling (use 1 - 2 kg). Leave the door ajar and stay close to the stove during the lighting phase. • Good layer of embers Be certain to have a good layer of em- bers before refilling. The wood should light within 2 minutes. If ...

Discuss the cleaning options with your chimney sweep. If there is insufficient draught in the chimney, it may be a good idea to install the flue pipe straight up, so as to minimise smoke migration in the actual com- bustion chamber. Avoid having any more bends than necessary, and limit the length of the flue pipe so as not to reduce the draught. Fresh air supply A wood-burning stove requires air for combustion. As a result, firing a wood- burning stove will help to create a healthy climate in your house. If the house is very tightly sealed, and particularly if ther ...