modway EEI-2285 Manual 

EEI – 2285 OFFICE CHAIR Component: A Chair Back x1 Thank you for purchasing the MODWAY OFFICE CHAIR！ Before you start, here is some helpful advice: 1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step instructions. 2.Owing to the size and weight of the office chair, we recommend that it is assembled by two adults, on a carpeted or padded area, in the room that it is intended for. Approximate assembly time: 30 minutes. 3.Please do not use any tools other than those provided or recommended in these instructions. 4.Please do not throw away any of the packaging or instructions until you have checked all the components and hardware and the furniture is fully assembled. 5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the components from time to time, so please save the tools that have been provided. 6.Please keep all pieces out of reach of small children. A Caster x5 H G H Chair Base x1 H H H H G C B B Left Arm x1 D Chair Seat x1 F Cylinder x1 E Hardware: 1 Bolt M6x20mm x2 7 Allen Wrench M6 x1 3 Bolt M6x30mm x2 4 Bolt M8x35mm x4 D C Right Arm x1 2 Bolt M6x25mm x4 5 Flat Washer x4 6 Plastic Washer x4 F E Control Mechanism x1

EEI – 2285 OFFICE CHAIR STEP 1: STEP 2: Please put Chair Base (G) upside down on a carpeted or padded surface. Insert 1 piece of Castor (H) into the Chair Base (G) as shown by hand. Repeat the same steps for the remaining 4pcs of Castor (H). H H H H H G Flip the assembled Chair Base (G) with Castors (H) on the floor. Insert the bottom end of Cylinder (F) into the assembled Chair Base (G) as shown. F H H H H H G

EEI – 2285 OFFICE CHAIR STEP 3: STEP 4: Flip the Chair Seat (D) upside down on a carpeted or padded surface. Attach the assembled Chair Back (A) and Arm (B&C) to the bottom of Chair Seat (D) by using 4 pieces of Bolt (4) and 4 pieces of Flat Washer (5) as shown. Tighten Bolt (4) by using Allen Wrench (7) clockwise until secure. 2x4pcs 6x4pcs 7x1pc Hardware & Tool required Place Chair Back (A) upside down on a carpeted or padded surface as shown. Attach Left Arm (B) to Chair Back (A) by using 2 pieces of Bolt (2) as shown. Tighten Bolt (2) by using Allen Wrench (7) clockwise until secure. Then insert 2 pieces of Plastic Cover (6) into pre-drilled holes as shown. Repeat the same steps for the Right Arm (C). A C B 2 6 6 2 2 4 7 6 6 4x4pcs 5x4pcs 7x1pc Hardware & Tool required BOTTOM D C B A 5 4 5 7 FRONT BACK

EEI – 2285 OFFICE CHAIR STEP 5: STEP 6: FRONT Place Control Mechanism (E) to the bottom of the Chair Seat (D). Attach the front of Control Mechanism (E) by using 2 pieces of Bolt (3), and the back of it by using 2 pieces of Bolt (1) as shown. Tighten Bolt (1&3) by using Allen Wrench (7) clockwise until secure. Hardware & Tool required Carefully turn over the assembled Chair Back (A), Arm (B&C), Chair Seat (D) and Control Mechanism (E). Please insert the bottom holes of Control Mechanism (E) into the top end of assembled Cylinder (F) as shown. Seat on Chair Seat (D) to fully tighten the office chair. Assembly is complete. The office chair is ready to be enjoyed now! 1x2pcs 3x2pcs 7x1pc D BOTTOM C B A E 1 1 A B C D E F G 3 3 7