Kauber MIDI Assembly Instructions Manual

selection of projection surfaces makes it the most frequently selected screen for installation in assembly halls, lecture rooms and large conference and halls and auditoriums. IMPORTANT!!! REMARKS ON INSTALLATION AND USE 1. The screen’s lower casing and bar are protected against damage using a polyurethane foam and tapes. The foam and tapes which secure the casing should be removed only at step no. 4, while the foam which secures the lower bar only at step no. 6 of these instructions. 2. The screen should be mounted in a place away from moisture and intense sunlight. 3. To clean the product, use a soft, damp cloth. Do not use active detergents. Do not allow for water and other fluids to get inside the device. After cleaning, the screen should be carefully wiped, removing any remaining moisture. 4. A correctly mounted screen must be absolutely level in every plane. 5. No more than one control switch can be connected to the screen/lift at one time. 6. One control switch (e.g. RC01/RC02/Trigger 12V/Trigger 230V/IR Receiver/RS Receiver, etc.) cannot be connected to more than one device, like a screen, lift, roller-blind, etc., at a time. Package contents: Quantity Projection screen 1 pcs. Mounting holder 3 pcs. Mounting angle bracket 3 pcs. Ø14 anchor plug for wall mounting 12 pcs. M6x12 screw 12 pcs. M6 washer 12 pcs. L-shaped screen locking and securing bar 6 pcs. Screen hanging chain 2 pcs. Key for screen end position adjustment 1 pcs. Wall-mounted pushbutton switch (available with screens without built in radio control) 1 pcs. Switch Switch Controller Screen/lift motor Screen/lift motor Screen/lift motor

center (Fig. 1). The mounting holders must be horizontally aligned. You can check the dimensions of the casing at the end of the instruction, in the “Technical data” section. Fig.1 2. Screw the mounting holders to the wall using the Ø14 anchor plugs included in the package (Fig.2) ATTENTION! The anchor plugs provided in the package can only be used with walls made out of solid materials (e.g. concrete, aerated concrete). In the event of mounting the screen to materials other than stated above, select other anchor plugs correspondingly. Fig.2 Level length L length L/2

Fig.3 4. Attach the screen to the mounted holders. In order to do this more easily, use the chains, which you can hold to lift the screen. After mounting the screen, disconnect the chains. Fig.4

To attach the screen, perform the following 3 steps: Fig.5 STEP 1 Raise the screen upwards, so that it touches the mounting holders. Fig.6 STEP 2 Move the screen towards the hooks. Fig.7

Fig.8 6. Once hung, lock the screen using the locking bars by sliding them into the gap between the holder and the screen. The locking bar gap is shown in figures: 8, 9a and 9b. Fig.9a

too low or not low enough, its end positions can be adjusted using the supplied key (fig.10). ATTENTION! Adjustment of end positions can only be performed by a qualified person. Any adjustments are performed at the users responsibility. In the event of improper adjustment, the screen may sustain damage which is not covered by the guarantee. End position adjustment - Adjustment of upper end position (white stopper). Fig.10 white stopper

Fig.11 yellow stopper

Before attempting to mount the screen’s casing, lead the power supply cable to the mounting location and connect it during screen installation according to diagram A (Fig.11A) or according to diagram B in case of screens with built in radio control (Fig.11B). . DIAGRAM A Fig. 11A DIAGRAM B (built in radio control) Fig.11B

(The switch available with a screen without built in radio control)

B- surface height F=A+96mm J=A+40mm K=50mm MIDI + BLACK FRAME A- active surface width B- active surface height C=A+100mm D=B+100mm F=A+196mm J=A+140mm K=50mm Technical data: Power supply: 230V 50Hz Power consumption: 160W – screen without built in radio control 240W – screen with built in radio control

You are welcome to purchase other KAUBER brand products