Econoco MBSLD Instructions Manual
Read Online
Read the Econoco MBSLD Instructions Manual online using the built-in PDF viewer.
Text of the manual
Item # MBSLD, MBSLDO
6X
1/4-20 x 1.5" LONG
LOW PROFILE SOCKET
HEAD CAP SCREW
4X
5/16-18 x 1" LONG
CSK SOCKET HEAD
CAP SCREW
4X
1/4-20 x 0.5" LONG
LOW PROFILE SOCKET
HEAD CAP SCREW
2X
ALLEN KEY
2 PEOPLE
NEEDED FOR
ASSEMBLY
3X
1/4 SPRING LOCK
WASHER
Item # MBSLD, MBSLDO
SHEET 1 OF 6
SIDE - TOP
SIDE - BOTTOM
SIDE - BASE
B
A
4X
4X
LOCKING
CASTER
NON-LOCKING
CASTER
NON-LOCKING
CASTER
LOCKING
CASTER
HOOK
BELT LOOP
2
A. ASSEMBLE THE SIDE-BOTTOM WITH BASE.
B. ASSEMBLE THE SIDE-BOTTOM WITH SIDE-TOP.
NOTE: WHEN ASSEMBLING BASE TO SIDE-BOTTOM, THE BENT LEGS
SHOULD FACE THE SAME DIRECTION AS THE U CHANNEL.
REPEAT FOR SECOND SET OF SIDE PIECES.
1
USE INCLUDED CASTER WRENCH TO ASSEMBLE THE SIDE-BASES WITH
CASTERS.
A. ASSEMBLE THE BASE WITH BELT LOOP WITH CASTERS.
B. ASSEMBLE THE BASE WITH HOOK WITH CASTERS.
NOTE: PUT THE NON-LOCKING/ LOCKING CASTERS AS SHOWN.
B
A
Item # MBSLD, MBSLDO
SHEET 2 OF 6
1/4-20 x 1.5" LONG
LOW PROFILE SOCKET
HEAD CAP SCREW
3
ASSEMBLE (2) SIDES WITH
BOTTOM CROSSBAR. MAKE SURE
U CHANNEL IS FACING UP.
4
ASSEMBLE MIDDLE UPRIGHT.
1X
1/4-20 x 1.5" LONG
LOW PROFILE SOCKET
HEAD CAP SCREW
Item # MBSLD, MBSLDO
SHEET 3 OF 6
SIDE BASE WITH HOOK IS ON TOP.
6
CAREFULLY SLIDE TOP PANEL INTO RACK.
TAKE CARE NOT TO BEND THE ACRYLIC WHEN SLIDING IN ACRYLIC PANEL.
5
TIP UNIT ON ITS SIDE.
MAKE SURE THE SIDE-BASE WITH HOOK IS FACING UPWARDS.
CAREFULLY SLIDE BOTTOM PANEL INTO RACK.
TAKE CARE NOT TO BEND THE ACRYLIC WHEN SLIDING IN ACRYLIC PANEL.
Item # MBSLD, MBSLDO
SHEET 4 OF 6
ASSEMBLE TOP CROSSBAR.
HAND TIGHTEN FROM TOP TO BOTTOM.
THEN GO BACK AND FULLY TIGHTEN WITH ALLEN KEYS.
3X
1/4-20 x 1.5" LONG
LOW PROFILE SOCKET
HEAD CAP SCREW
3X
1/4 SPRING LOCK
WASHER
Item # MBSLD, MBSLDO
SHEET 5 OF 6
BASE WITH BELT LOOP
BASE WITH HOOK
1
LINK PLATE
2
FOR PUTTING (2) ROLLING
RACKS TOGETHER
1
PUT TWO UNITS SIDE BY SIDE.
MAKE SURE THE BASE WITH BELT LOOP AND
BASE WITH HOOK ARE PLACED END TO END.
HOOK THE TWO BASES TOGETHER. LIFT THE
BASE WITH HOOK AND DROP IT INSIDE THE
BELT LOOP.
2
UNSCREW THE TOP SCREWS FROM THE
JOINING UNIT. SWING LINK PLATE AND SCREW
IN TO SECURE THE TWO UNITS ON TOP.
Item # MBSLD, MBSLDO
SHEET 6 OF 6
