ABB TPL65VA33 Operation Manual

CH 5401 Baden Type TPL65VA33 HT564931 nMmax 503 t Mmax 650 nBmax 486 t Bmax 620 1/s °C 01210 35 50 50 Year 2016 made in Switzerland Application according to the Operation Manual kg HZTL2464 English TPL65VA33 Original Operation Manual

The operational limits for the turbocharger nBmax, tBmax, nMmax, tMmax, inspection- and replacement intervals for the compon- ents concerned on the rating plate are valid for the operational mode and compressor inlet condition, which has been agreed upon between the engine builder and ABB. Note: Replacement intervals of components depends on the load profi le, turbine inlet temperature, suction air temperature and turbocharger speed. In case the operation conditions differs signifi cantly from what is considered to be normal for the cur- rent application, it is recommended to contact ABB for a re-calculation of replacement intervals. Frequent load alterations, high temperatures and high speed lower the life of components. Unless otherwise agreed, the application limits nMmax, tMmax are valid for the test operation for a limited time.

Table of contents Page 1 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Table of contents 1 Preliminary remarks 1.1 Purpose of this manual 1.2 Layout and function 1.3 Intended use of the turbocharger 1.4 Storage of new turbochargers and spare parts 1.5 Essential information 1.6 Symbols and definitions 1.7 Turbocharger rating plate 1.8 Contact information 2 Safety 2.1 Introduction 2.2 CE conformity 2.3 Definition of mandatory signs 2.4 Definition of Safety instructions 2.5 Warning plates on the turbocharger 2.6 Safe operation and maintenance 2.7 Hazards during operation and maintenance 2.8 Periodic checking of the pressure vessel 2.9 Lifting loads 3 Commissioning 3.1 Oil supply 3.2 Inspection work 3.3 Commissioning after taking out of operation 4 Operation 4.1 Noise emissions 4.2 Servicing work 4.3 Replacement intervals for turbocharger components 4.4 Speed measurement 4.5 Emergency operation TPL..VA 4.6 Stopping the engine

Table of contents Page 2 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C 5 Maintenance 5.1 Foreword to Maintenance 5.2 Cleaning the filter silencer 5.3 Cleaning the compressor during operation 5.4 Cleaning turbines and guide vanes during operation 6 Troubleshooting 6.1 Malfunctions when starting 6.2 Surging of the turbocharger 6.3 Malfunctions during operation 6.4 Malfunctions when stopping 6.5 Speed measurement system 6.6 Variable Turbine Geometry 7 Removal and installation 7.1 Turbocharger weights 7.2 Removing the turbocharger 7.3 Installing the turbocharger 8 Disassembly and assembly 8.1 Introduction 8.2 Module weights 8.3 Removing and fitting filter silencer or air suction branch 8.4 Axial clearance 8.5 Removing cartridge group 8.6 Removing and fitting turbine diffuser 8.7 Removing variable turbine geometry module with gas inlet casing 8.8 Fitting the variable turbine geometry module and the gas inlet casing 8.9 Installing cartridge group 8.10 Table of tightening torques 9 Taking out of operation at short notice 9.1 Possibilities for emergency repair 9.2 Fitting the cover plate 9.3 Blocking the inlets and outlets 9.4 Turbocharger bypass 10 Mothballing the turbocharger

Table of contents Page 3 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C 10.1 Taking the engine out of operation for up to 12 months 10.2 Taking the engine out of operation for more than 12 months 11 Disposing of turbocharger components 12 Spare parts 12.1 Ordering spare parts 12.2 View of turbocharger with part numbers 12.3 View of cartridge group with part numbers

Preliminary remarks 1 Purpose of this manual 1.1 Page 5 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Preliminary remarks Purpose of this manual 1.1 This operation manual belongs to the turbocharger with the identical HT number (01), see the cover sheet of the operation manual and the turbocharger rating plate. Operation Manual This Operation Manual enables you to familiarize yourself with the turbocharger supplied by ABB Turbo Systems and to use it as intended. It provides important information in order that the turbocharger can be operated safely, correctly and efficiently. This Operation Manual complements and expands existing national regulations concerning work safety and accident prevention. Target group This Operation Manual is intended for engineers and qualified mechanics who are responsible for operating the engine and the turbocharger installed on it. Availability of operation manual An operation manual must be available at all times at the place where the turbocharger is used. Everyone who operates or works on the turbocharger must have first read and understood the operation manual. 1 1.1

Preliminary remarks 1 Layout and function 1.2 Page 6 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Layout and function 1.2 01 Filter silencer 08 Nozzle ring 02 Radial plain bearing 09 Turbine wheel 03 Thrust bearing 10 Bearing casing 04 Bearing bush 11 Diffuser 05 Radial plain bearing 12 Compressor wheel 06 Gas outlet casing 13 Air outlet casing 07 Gas inlet casing 1.2

Preliminary remarks 1 Layout and function 1.2 Page 7 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Mode of operation The turbocharger is a turbomachine and consists of the following main components:  Turbine  Compressor These are both mounted on a common shaft. The exhaust gases from the diesel engine flow through the gas inlet casing (07) and nozzle ring (08) to the turbine wheel. The turbine wheel (09) uses the energy contained in the exhaust gas to drive the compressor wheel (12). The compressor then draws in fresh air and forces precompressed air into the cylinders. The exhaust gases escape to free air through an exhaust gas pipe which is connected to the gas outlet casing (06). The air which is necessary for operation of the diesel engine and is compressed in the turbocharger is drawn through the suction branch or the filter silencer (01) into the compressor wheel (12). It then passes through the diffuser (11) and leaves the turbocharger through the air outlet casing (13). The rotor runs in two radial plain bearings (02/05). One plain bearing is in the bearing bush (04), and the second one is in the axial thrust bearing (03) at the compressor end. The plain bearings are connected to a central lubricating oil duct which is fed with oil from the engine's lubricating oil circuit. The oil outlet is always at the lowest point of the bearing casing (10). Turbocharger version with compressor wheel cooling system Depending on its range of use, the turbocharger is provided with a compressor wheel cooling system. Compressor wheel cooling means that, after the charge air cooler at the engine end, cooled compressor air is delivered to the turbocharger to cool the compressor wheel. In view of the respective operating conditions, it is absolutely essential that the compressor wheel is cooled in order to guarantee its reliability and replacement intervals. In the case of the turbocharger version with compressor wheel cooling, the cooling air is supplied through the side connection (15) in the bearing casing.

Preliminary remarks 1 Layout and function 1.2 Page 8 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Additional function TPL..V. These turbocharger types have adjustable guide vanes at the turbine end instead of a nozzle ring.

Preliminary remarks 1 Intended use of the turbocharger 1.3 Page 9 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Intended use of the turbocharger 1.3 NOTICE This turbocharger supplied by ABB Turbo Systems has been developed for use on diesel engines to generate the volume of air and the charging pressure required to operate the engine. The engine builder has provided ABB Turbo Systems with information regarding the intended use of the engine, from which the operating limits specific to the turbocharger shown on the rating plate (such as operating speeds, temperatures, exchange intervals / replacement intervals) have been derived. If it is used in conjunction with a gas engine, the engine must not be installed in a potentially explosive environment, and precautionary measures must be taken to ensure that the machine room as a whole is classified as not potentially explosive. Any other use will be regarded as a special application which must first be discussed with ABB Turbo Systems. The manufacturer accepts no liability for other applications. If it is used otherwise, ABB Turbo Systems reserves the right to reject all warranty claims. This turbocharger was built according to state-of-the-art technology and is operationally safe according to recognised safety regulations. WARNING Improper operation and maintenance of the turbocharger can result in danger to life and limb of the user or third parties. In addition, improper use may cause damage to the machine.  The machine may be operated only by trained personnel. Use of the turbocharger as intended also includes observance of the installation / fitting, disassembly / removal, operating, maintenance / servicing and repair conditions specified by the manufacturer. Disposal regulations set down by local authorities must be observed. The turbocharger may be installed only when in technically perfect condition while observing the instructions given in the engine builder's manual. It may be used only for the intended purpose and operated in compliance with the operation manual.  Malfunctions which could affect safety must be eliminated immediately. The manufacturer accepts no liability for any damage resulting from unauthorised alterations to the turbocharger. 1.3 State of the art Perfect condition

Preliminary remarks 1 Storage of new turbochargers and spare parts 1.4 Page 10 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Storage of new turbochargers and spare parts 1.4 Storage of new turbochargers and spare parts up to 6 months New turbochargers and spare parts from ABB Turbo Systems can be stored in sealed packaging without additional mothballing measures for up to 6 months from the date of delivery (marked by the VCI label on the package). Volatile Corrosion Inhibitor (VCI) Only dry rooms in which the relative humidity is between 40…70 % and no condensation can form are suitable for storage. Storage of new turbochargers and spare parts for more than 6 months (VCI) WARNING Protection of health when handling VCIs VCI products are not hazardous in the sense of the Hazardous Substances Ordinance. Nevertheless, the following points are to be observed when handling VCIs:  Ensure good room ventilation.  Do not eat, drink or keep food at the workplace while working with VCIs.  Wear safety gloves.  Clean hands and face after working with VCIs.  For further information refer to www.branopac.com. Wear safety gloves against chemical risks. The following mothballing measures are required every 6 months:  Open the package.  Remove the VCI corrosion protection emitter from the package and replace it with a new, identical VCI corrosion protection emitter. New VCI corrosion protection emitters can be obtained at www.branopac.com.  Dispose of the old VCI corrosion protection emitter in an environmentally compatible manner, professionally and in accordance with local regulations.  Seal the package. The better the external seal is designed, the more permanent the protection. 1.4

Preliminary remarks 1 Storage of new turbochargers and spare parts 1.4 Page 11 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Long-term storage of replacement turbochargers or spare parts Per order, turbochargers or cartridge groups will be prepared by ABB Turbo Systems for prolonged storage. The package is equipped with a hygrometer (see illustration). The following measures are required every 6 months:  Check the hygrometer (02) in the sight-glass. There is an opening (01) in the wooden crate which allows this check to be carried out. When the display field has changed colour at the 70% level, the maximum permissible humidity has been exceeded. In this case the turbocharger or rotor must be inspected by an ABB Turbocharging Service Station and repacked.  Inspect the package for damage. If the package is damaged, the turbocharger or cartridge group must be inspected by an ABB Turbocharging Service Station and repacked. After every 3 years the following work steps must be performed by an ABB Turbocharging Service Station:  Inspect the components  Exchange the desiccant agent  Repackage the components. NOTICE Replacement components ready for operation If the 70% display field of the hygrometer (02) has not changed colour and the package is undamaged, the replacement turbocharger or replacement cartridge group can be placed into operation without any prior testing by an ABB Turbocharging Service Station. Unpacking replacement turbochargers or spare parts The corrosion protection effect ends after the material is unpacked from the VCI package. To avoid the formation of condensation, the surroundings and the content of the package must have the same temperature during unpacking.

Preliminary remarks 1 Essential information 1.5 Page 12 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Essential information 1.5 Organisational measures In addition to this manual, the general, statutory regulations applicable in the respective country for the prevention of accidents and the protection of the environment must be observed. This also applies to the provision and wearing of personnel protection equipment. NOTICE The safety and risk consciousness of the personnel working on and with the turbocharger must be checked regularly with reference to this manual.  The turbocharger must be shut down immediately by stopping the engine in the event of alterations affecting safety or of corresponding operating behaviour. The fault must be reported to the person or department responsible. NOTICE Additions and alterations to, and conversions of the turbocharger that could compromise safety require the prior approval of ABB Turbo Systems. 1.5

Preliminary remarks 1 Essential information 1.5 Page 13 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Original parts and safety Original parts and accessories are specially designed for the turbocharger supplied by ABB Turbo Systems. WARNING Use original parts Operation of the turbocharger with non-original parts can impair the safety of the turbocharger and can cause serious damage to property and injury to personnel.  Only use original parts from ABB Turbo Systems. ABB Turbo Systems accepts no liability for any damage resulting from the use of non-original parts and corresponding accessories. Competence of personnel The turbocharger must only be operated and serviced by trained and authorised personnel. Basic mechanical training is a prerequisite.

Preliminary remarks 1 Essential information 1.5 Page 14 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Design variants This document is valid for different design variants of turbochargers. There may be sections and descriptions of components that are not relevant for a specific turbocharger variant. ABB Turbocharging Service Stations will be happy to provide information on questions regarding a design variant (see Contact information at www.abb.com/turbocharging). Accuracy of illustrations The illustrations in this document are general in nature and intended for ease of understanding. Differences in detail are therefore possible. Registered trademarks Registered trademarks of external companies are used in this document. The trademarks are marked with ®.

Preliminary remarks 1 Symbols and definitions 1.6 Page 15 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Symbols and definitions 1.6 The following symbols are used in the documents:  Prerequisite  Work step  Enumeration, first level - Enumeration, second level Definition of notes NOTICE Note A note provides suggestions which facilitate the work on the product. Definition of mandatory signs Mandatory signs show the protective equipment to be worn for a task. The mandatory signs are described in chapter Safety and must be complied with. Definition of caution / warning The caution and warning signs are described in the chapter Safety. ABB Turbo Systems In this document, ABB Turbo Systems Ltd is abbreviated to ABB Turbo Systems. Official ABB Turbo Systems Service Stations In this document, official service stations are referred to as ABB Turbocharging Service Stations. They are inspected and certified regularly by ABB Turbo Systems. See also chapter Contact information [➙ 18]. 1.6

Preliminary remarks 1 Turbocharger rating plate 1.7 Page 16 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Turbocharger rating plate 1.7 01 Turbocharger operating limits at engine overload (110%). Only when operating in the test rig unless otherwise agreed with the enginebuilder. 02 Turbocharger operating limits during operation 03 Replacement interval for plain bearings in 1000 h 04 Replacement interval for compressor in 1000 h 05 Replacement interval for turbine in 1000 h 06 Part number for customer 07 Designation of special design 08 Turbocharger weight in kg 09 Turbocharger type 10 Serial number 11 Year of turbocharger construction 1.7 Operating limits Recommended replacement intervals for turbocharger components Further information

Preliminary remarks 1 Turbocharger rating plate 1.7 Page 17 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Explanation of the rating plate The recommended replacement intervals and the corresponding operational limits are jointly defined with the engine manufacturer. This information is specific to the system. Operation above the indicated values nBmax, tBmax can considerably shorten the recommended replacement intervals. In such cases, we recommend that you contact the nearest official ABB Turbocharging service station. nMmaxand tMmax normally apply only when running at overload (110%) during trials on the engine test bed. These limits can also be permitted during operation for special applications. Operation above nMmax and tMmax is not permitted. Non-observance of the recommended replacement intervals can increase the risk of unpredictable component failures. Positions of the rating plates A rating plate is attached to the turbocharger foot, one on the left and one on the right. In the case of turbochargers with insulation supplied by ABB Turbo Systems, at least one additional rating plate is attached to the insulation of the gas outlet casing. 1.7.1 1.7.2

Preliminary remarks 1 Contact information 1.8 Page 18 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Contact information 1.8 Contact information Contact information for the official service stations of ABB Turbo Systems is available online.  Scan the QR code to access our website. ABB Turbo Systems AG Bruggerstrasse 71a CH-5401 Baden Switzerland www.abb.com/turbocharging 1.8

Safety 2 Introduction 2.1 Page 19 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Safety Introduction 2.1 Turbochargers manufactured by ABB Turbo Systems are state of the art and comply with the pertinent safety and health-protection requirements that applied when the turbocharger was manufactured. Consequently, the turbocharger is safe to operate. Nevertheless, during turbocharger operation and when working on the turbocharger, residual risks can exist which:  originate from the turbocharger itself and its accessories  originate from the operating and auxiliary materials used  are the consequence of insufficient observance of the safety instructions  are the consequence of unsatisfactory and improper execution of maintenance and inspection work The operator is responsible for access to the turbocharger as well as the organisational measures which regulate the safe handling of the turbocharger by his personnel. All instructions in this chapter must be observed to ensure safe and trouble-free turbocharger operation and during work on the turbocharger. In the same vein, all other specially marked safety instructions in every chapter of this manual must be observed (see the section entitled Definition of safety instructions). 2 2.1

Safety 2 CE conformity 2.2 Page 20 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C CE conformity 2.2 Information ABB turbochargers fulfil Directive 2006/42/EC on machinery and are considered partly completed machinery in the sense of Article 2 g. 2.2

Safety 2 Definition of mandatory signs 2.3 Page 21 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Definition of mandatory signs 2.3 To be worn at all times Protective clothing Safety footwear against mechanical hazards To be worn according to the specific work Safety glasses Safety goggles Safety gloves against - mechanical hazards - chemical hazards - heat hazards Respiratory mask against - dust - gases Safety helmet Ear protection 2.3

Safety 2 Definition of Safety instructions 2.4 Page 22 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Definition of Safety instructions 2.4 The following symbols and terms used in this manual concern safety or refer to possible hazards: WARNING Definition of warning Serious personal injuries and even accidents with fatal consequences may occur if work and operating instructions marked with this symbol and the word WARNING are either not followed or not followed precisely.  Warning signs must be observed at all times. CAUTION Definition of caution Serious machine or property damage may occur if work and operating instructions marked with this symbol and the word CAUTION are either not followed or not followed precisely.  Caution signs must be observed at all times. 2.4

Safety 2 Warning plates on the turbocharger 2.5 Page 23 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Warning plates on the turbocharger 2.5 Warnings that have been attached to turbochargers by ABB Turbo Systems must not be removed. Illegible warnings must be replaced with new ones. Further information is available from ABB Turbocharging service stations. Part number Size [mm] Product 81080 105 x 74 TPL / TPR When uninsulated turbochargers are delivered to the engine builder, the warning plates must be subsequently attached to the insulation. This is the responsibility of the engine builder. 2.5

Safety 2 Safe operation and maintenance 2.6 Page 24 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Safe operation and maintenance 2.6 The instructions specified in this section are for the safety of personnel. Together with the instructions in the Hazards during operation and maintenance section, they allow the user to safely use the turbocharger. Work safety and work area safety WARNING Risk of falling There is the risk that someone can fall when working on the turbocharger.  Do not climb on the turbocharger or on parts attached to it or use these as climbing aids.  When working at levels above the head, use climbing aids and work platforms suitable for this purpose.  Observe all general regulations for the prevention of accidents.  Do not work on the turbocharger if you are under physical or mental stress.  Work only with suitable tools as well as equipment and working materials that are in perfect condition.  Electric tools must be solidly earthed, and connecting cables may not be damaged.  Keep the workplace clean, clear away loose objects and remove obstacles on the floor.  Keep the floor, equipment and the turbocharger clean.  Have oil binding materials ready at hand and keep oil catch pans ready or in position  Eliminate leaks.  Keep fire-protection materials and fire-extinguishing equipment ready. Welding work  If welding work is being carried out above the turbocharger, make sure to cover the filter silencer so that the filter mat is not damaged.  Remove combustible objects and substances out of the range of flying sparks.  Cover all connections on the turbocharger so that no foreign objects can get into the turbocharger. 2.6

Safety 2 Safe operation and maintenance 2.6 Page 25 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Safety during start-up / commissioning and operation  Before starting work, carry out visual inspection of working area.  Remove any obstacles and objects lying around.  Before start-up / commissioning, check all pipes from and to turbocharger for damage and leaks.  Don't work in any way that could impair safety when working on turbocharger.  After about every 12 hours of operation or at least once a day, inspect turbocharger for visible damage and defects.  Immediately report any damage or changes in operational performance to person responsible.  If damage is discovered, immediately shut down turbocharger and secure it against inadvertent or unauthorized use.  When switching on auxiliary power sources (hydraulics, pneumatics, electricity, water), keep an eye open for any hazards resulting from supplying these power sources. Safety during cleaning It is possible that detergents or solvents will be used for cleaning. In this case, the safety instructions of the Hazard due to operating materials and supplies section in this chapter must always be observed.  Protect the floor against unintentional penetration of detergents or solvents before starting cleaning operations.  Wear appropriate protective clothing.  Inspect the electric cables for abrasion and damaged areas before and after your cleaning work.

Safety 2 Safe operation and maintenance 2.6 Page 26 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Safety during disassembly, assembly, maintenance and troubleshooting  Always perform the specified adjustments, servicing as well as inspection work and observe inspection intervals.  Inform operating personnel about all service and repair work before beginning.  Before opening a cover or removing a protective device on a turbocharger, the engine must be switched off and the turbocharger must have come to a standstill.  Ensure that the supply of oil is interrupted, especially with an external oil supply.  Put the engine into operation only after all parts have been refitted properly. CAUTION Mechanical work on the turbocharger Possible damage to or destruction of components on the turbocharger.  Perform only those tasks that are described in this manual.  Perform work only for which training has been carried out. Safety when taking out of operation or mothballing  Secure the rotor so it cannot turn. The rotor can turn on its own from the force of the stack draught.  Clean the turbocharger before mothballing it.  Wear appropriate protective clothing.

Safety 2 Hazards during operation and maintenance 2.7 Page 27 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Hazards during operation and maintenance 2.7 Mechanical hazards during operation During normal operation, no mechanical hazards emanate from the turbocharger if it has been installed properly. WARNING Risk of injury Contact with rotating parts can lead to serious injuries. The turbocharger must never be operated without a filter silencer or an air suction branch. When the engine is at a standstill, the rotor can turn on its own because of stack draught.  Operate the turbocharger in accordance with instructions.  During maintenance work, secure the rotor against unintentional rotation. Mechanical hazards when working on the turbocharger During maintenance work, various risks can occur through the improper handling of components, through the non-observance of work instructions, due to inadequate care or as a consequence of insufficient training. WARNING Mechanical hazards Serious personal injuries or accidents with fatal consequences can occur through mechanical influences as a result of risky, improper working methods.  Heed the general rules for work safety and accident prevention.  Ensure the safety of the work area.  Perform only those tasks that are described in this manual.  Perform work only for which training has been carried out. 2.7

Safety 2 Hazards during operation and maintenance 2.7 Page 28 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Hazards due to noise The development of noise during operation is influenced by the installation and operating conditions. Noise with a sound pressure level exceeding 85 dB(A) is harmful. WARNING Hazards due to noise Noise can cause impaired hearing, damage to health, mental disturbances, diminished attention and irritation.  Always wear ear protection when the engine is running.  When the sound pressure level is above 85 dB(A), always wear ear protection. Wear ear protection. Hazards due to hot surfaces and substances During operation, turbocharger surfaces and attached parts as well as operating materials (lubricating oil) become hot. The surface temperature is dependent on the effectiveness of the insulation being used. The temperature can become high enough so that it falls into ranges where burns are possible. WARNING Risk of burning Touching hot surfaces or contact with hot operating materials can lead to serious burns.  Do not touch hot surfaces and heed the warning plate on the turbocharger.  Wear heat-resistant safety gloves and protective clothing.  Allow the turbocharger to cool down before carrying out any work. Wear safety gloves against thermal risks.

Safety 2 Hazards during operation and maintenance 2.7 Page 29 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C WARNING Hot surfaces on uninsulated turbochargers Uninsulated turbochargers can cause serious personal injuries (burns). The turbocharger is supplied by ABB Turbo Systems without insulation depending on the order from the engine builder. In this case, the engine builder is responsible for insulating the turbocharger properly or for providing protection against hot surfaces being touched.  The engine builder's instructions and specifications about protection against hot turbocharger surfaces must be observed in every case. Hazards due to operating and auxiliary materials Operating and auxiliary materials are substances used for operation or the execution of maintenance work. Oils, greases, coolants, cleaning agents and solvents, acids, etc. can be regarded as hazardous materials. Operating and auxiliary materials can be combustible and easily ignited. WARNING Handling operating and auxiliary materials Ingestion or inhalation of vapours of operating and auxiliary materials or contact with such can cause damage to health.  Avoid inhalation and contact with the skin.  Ensure good ventilation.  Observe details in the safety data sheets of the operating and auxiliary materials.  Observe local laws. Wear safety goggles. Wear safety gloves against chemical risks. Wear a respiratory mask to protect against gases.

Safety 2 Hazards during operation and maintenance 2.7 Page 30 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C WARNING Risk of fire, explosion Combustible or easily ignited operating and auxiliary materials can burst into flame, or vapours from them can cause explosions.  Observe specifications in the safety data sheets of the operating and auxiliary materials.  Observe local legislation.  Do not allow any exposed flame during cleaning work.  Perform cleaning outdoors or ensure for adequate aeration and ventilation. CAUTION Risk of environmental damage The escape of operating and auxiliary materials into the atmosphere or contamination of the ground and water due to improper disposal can lead to environmental damage.  Handle operating and auxiliary materials carefully.  Heed the instructions for use, safety data sheets and hazard notices on the containers of the operating and auxiliary materials.  Wear appropriate protective clothing.  Avoid inhalation and contact with the skin.  Ensure that the work space is adequately ventilated.  Seal containers tightly immediately after use and put them away.  Collect used working and auxiliary materials safely, store them separately in suitable containers and dispose of them properly and in an environmentally compatible manner in accordance with statutory regulations.  In the event of leaks or after spilling, immediately spread a suitable binding agent and dispose of it properly and in an environmentally compatible manner in accordance with statutory regulations.

Safety 2 Hazards during operation and maintenance 2.7 Page 31 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Hazards when handling insulating materials WARNING Hazards due to insulating materials Dust and fibres from insulating materials can cause damage to health or irritations. Unsuitable, combustible insulating materials signify a fire hazard.  Use only suitable, non-combustible insulating materials.  Ensure that the work area is well ventilated.  Avoid stirring up dust.  Use tools and processes which keep dust to a minimum.  Remove packing materials only in the work area.  Take particular care when removing old insulating materials.  Dispose of insulating materials properly and in an environmentally compatible way in accordance with applicable local regulations. Wear safety goggles. Wear a respiratory mask to protect against particles. Wear safety gloves against chemical risks.  Use only suitable, non-combustible insulating materials.  Ensure that the work area is well ventilated.  Wear suitable work clothing (safety glasses, respiratory mask).  Avoid stirring up dust.  Use tools and processes which keep dust to a minimum.  Remove packing materials only in the work area.  Take particular care when removing old insulating materials.  Dispose of insulating materials properly and in an environmentally compatible way in accordance with applicable local regulations.

Safety 2 Hazards during operation and maintenance 2.7 Page 32 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Hazards due to electrical components WARNING Hazards due to electrical components Electrical components operate with voltages which can present hazards to humans.  All work on or with electrical components may only be performed by trained specialists.  Heed any country-specific regulations.

Safety 2 Periodic checking of the pressure vessel 2.8 Page 33 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Periodic checking of the pressure vessel 2.8 The pressure vessels used by ABB Turbo Systems, such as those for wet or dry cleaning, are so-called "simple pressure vessels".  The local, statutory regulations covering periodic checks of pressure vessels must be observed.  The operator is responsible for the safe operation of the pressure vessel. WARNING Hazards from pressure vessels The operator must keep the pressure vessel in a proper condition and monitor it. Necessary repair or maintenance work must be carried out without delay and the required safety precautions must be taken.  Pressure equipment must not be operated if it has defects. 2.8

Safety 2 Lifting loads 2.9 Page 34 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Lifting loads 2.9 WARNING Suspended loads Loads not suspended in compliance with regulations may lead to personal injury or accidents with fatal consequences.  Loads must always be fastened to technically perfect lifting gear with sufficient loading capacity.  Make sure the load is suspended properly on the crane hook.  Do not let anyone stand beneath a suspended load. Wear safety gloves against mechanical risks. Wear safety helmet. In the case of two or more suspension points, the slinging angle must not exceed 45°. This avoids excessive loading due to inclined tensile loading.  Fasten turbocharger assemblies / components as described in respective handling steps.  Before attaching slings, allow turbocharger components to cool down (maximum 80°C).  Use suitable protection at sharp edges.  Completely screw in assembly / fitting devices without fail so that they cannot work loose during use.  Use assembly / fitting devices only for applications described.  Make sure removed turbocharger components stand safely and securely. 2.9

Commissioning 3 Oil supply 3.1 Page 35 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Commissioning Oil supply 3.1 A carefully designed and installed oil supply, which functions in all possible operational conditions, is an important prerequisite for trouble- free turbocharger operation. The turbocharger is normally lubricated with oil from the engine oil circuit. NOTICE With regard to the oil supply, please observe the engine builder's specifications for lubricating oil selection, oil change intervals, oil filtration, oil pressure and oil temperature. Oil filtration A lubricating oil filter system with a filter mesh size of ≤ 0.034 mm is adequate for this turbocharger. 3 3.1

Commissioning 3 Oil supply 3.1 Page 36 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Oil pressure The oil pressure in front of the turbocharger must be maintained precisely to ensure trouble-free operation. The permissible oil pressure ranges at measuring point M (blind connection) on the turbocharger are listed below. Status for operation Oil pressure in front of the turbocharger [bar] Permissible, for normal operation 1.3 … 2.5 Permissible, during engine warm-up 1.3 … 5.0 Temporarily permissible ( < 1h ) -> alarm 1.1 … 1.3 Not permissible -> emergency stop 0.0 … 1.1 Permissible, during pre- and post-lubrication (engine stopped) 0.2 … 2.5 NOTICE Oil orifice To make sure these oil pressures are obtained, a regulating orifice is fitted in the turbocharger oil inlet. The orifice is fitted by the engine builder and secured by a safety ring.

Commissioning 3 Oil supply 3.1 Page 37 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Oil temperature Lubricating oil temperature at the inlet CAUTION Machine damage If the oil temperature at the oil inlet exceeds the admissible range, this may lead to engine damage.  Observe oil temperature at the oil inlet according to the following table. Status for operation Oil temperature at the inlet Toil,inlet [°C] Permissible 30 … 90 Temporarily permissible (< 1h) -> alarm > 90 Not permissible -> stop the engine > 95 Not permissible -> Do not start the engine (before starting: preheat the oil) < 30 Lubricating oil temperature at the outlet The oil temperature at the outlet is mainly dependant on:  Lubricating oil temperature and pressure at the oil inlet  Engine load and turbocharger speed  Exhaust gas temperature The maximum admissible oil temperature at the outlet is listed in the following table. The specified oil outlet temperature is to be considered as alarm value for the turbocharger operation and must be monitored according to the current regulations. Status for operation Oil temperature at the outlet Toil,outlet [°C] Permissible ≤ 140 Temporarily permissible -> alarm > 140 Not permissible -> stop the engine > 160 If the turbocharger was operated for a longer period of time outside of the admissible range, ABB Turbo Systems recommends to have the turbocharger inspected by an ABB Turbocharging Service Station.

Commissioning 3 Inspection work 3.2 Page 38 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Inspection work 3.2 Inspection work includes preventive visual controls plus monitoring and measuring work before and during commissioning. Inspections help detect changes to the turbocharger. Machine damage can be avoided. Inspection before commissioning  Check for correct functioning.  Inspect for damage.  Check oil filter for cleanliness before commissioning. CAUTION It is urgently recommended that the entire lubricating system be flushed thoroughly with warm oil using a bypass pipe before starting up the first time (commissioning) and after all service work on the lubricating system. It is urgently recommended that a running-in filter is used when running in the engine and after all service work on the lubricating system.  Check the oil pressure in the oil supply lines.  Check that variable turbine geometry module can be adjusted. TPL65: Version with compressor wheel cooling system  Check whether compressor wheel cooling system is fitted to bearing casing. CAUTION Failure of compressor wheel cooling system The service life of the compressor wheel will be impaired if the breakdown of the compressor wheel cooling system lasts long.  Ensure supply of cooling air. 3.2 3.2.1 Monitoring equipment Air filter mat Lubricating system TPL..VA

Commissioning 3 Inspection work 3.2 Page 39 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Check after start-up (engine at idling speed) Lubricating system  Check oil pressure in oil supply lines.  Check oil inlet temperature. The permissible values are listed in the section Oil supply. Gas, air and oil lines  Check all gas, air and oil lines for leaks after starting the engine. Check when running up engine  Measure the speed, oil pressure and charging pressure at various engine performance levels.  Measure the exhaust gas temperature in front of and behind the turbine.  Measure the air temperature in front of and behind the compressor.  Check the functioning of the variable turbine geometry module. The measured values must be compared with the values in the acceptance test report while taking different operating conditions into account. NOTICE Lubricants and pastes used during assembly of the turbocharger liquefy or vaporise and might escape as an oily liquid in the first few hours after commissioning. If oily liquid continues to escape after this period, the operator is to search for the cause of a possible oil leak. The first step is to check the seal for the oil supply to the turbocharger. If this is not in proper condition, contact an official ABB Turbocharging service station. Inspection after 100 service hours Clean or replace lubricating oil filters after the first 100 service hours. 3.2.2 3.2.3 3.2.4

Commissioning 3 Commissioning after taking out of operation 3.3 Page 40 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Commissioning after taking out of operation 3.3  Remove cover plates (blind flanges) between compressor casing outlet and charge air duct, before gas inlet and after gas outlet.  Inspect exhaust gas duct / line in front of and after turbine for any combustion deposits, foreign matter or residual water. Clean and remove.  Inspect air supply line or filter silencer for any foreign matter. Clean and remove.  Start up turbocharger oil circulation system at engine end.  Prepare turbocharger for operation as instructed in section "Inspection work before start-up / commissioning" of chapter headed "Start-up / commissioning".  Start up turbocharger. TPL65: Version with compressor wheel cooling system  Remove screw plug on cooling air connection and fit cooling air line. 3.3 If provided

Operation 4 Noise emissions 4.1 Page 41 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Operation Noise emissions 4.1 WARNING Hazards due to noise Noise can cause impaired hearing, damage to health, mental disturbances, diminished attention and irritation.  Always wear ear protection when the engine is running.  When the sound pressure level is above 85 dB(A), always wear ear protection. Wear ear protection. The sound pressure level (A-weighted) of emissions is measured at a distance of 1 metre from the turbocharger. The highest sound pressure level of emissions1) reaches a maximum of 105 dB(A) near the filter silencer and over the entire speed range. The following prerequisites must be fulfilled on the turbocharger in order to observe this limit value:  Fitted air-inlet system  All standard, noise-reducing measures have been taken2).  The bellows at the air outlet have been perfectly insulated acoustically by the engine builder. He is also responsible for insulating the charge air / scavenging air line and the charge air cooler. 1) Directive 2006/42/EC, 1.7.4.2 / u / Paragraphs 5 + 7 : A-weighted emission sound pressure level 2) In the event of divergent insulation designs, the engine builder must ensure that equivalent acoustic insulating measures are taken. 4 4.1

Operation 4 Noise emissions 4.1 Page 42 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Suggestion for noise insulation of the bellows 01 Compressor casing 04 Insulation pads 02 Bellows 05 Insulation mat (at least 15 mm) 03 Charge air duct / scavenging air line 06 Sheet metal cover

Operation 4 Servicing work 4.2 Page 43 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Servicing work 4.2 Service work to be carried out during operation involves visual checks, monitoring, measuring, inspection work and functional checks. It is then possible for changes to the turbocharger to be identified and rectified. In this way, it can be ensured that the turbocharger remains in full working order. CAUTION Service intervals Service work on the turbocharger that is neglected or carried out too late can lead to excessive contamination and wear as well as operating failures.  Carry out service work at specified time intervals. CAUTION Shortened service intervals Despite observance of the service intervals, unusual loads, such as several start-stops a day, harsh environmental factors, poor fuel quality or heavy installation vibration can lead to premature machine damage.  A shortened service interval must be arranged with ABB Turbo Systems. NOTICE Service inspection after 5 years To prevent age- and stoppage-related machine damage, an inspection by an ABB Turbocharging Service Station is recommended at the latest 5 years after the last service. Service work every 25 … 50 hours  Visual inspection for air, exhaust gas, water and oil leaks.  Record operating data and enter it in the engine logbook.  Clarify the cause of any variances. CAUTION Unknown changes during operation The consequences can range from an impairment to a breakdown.  Have unknown causes clarified by an ABB Turbocharging service station. 4.2 4.2.1

Operation 4 Servicing work 4.2 Page 44 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Entries in engine logbook By monitoring the engine, conclusions can be drawn about the turbocharger performance. The following operating data and measured values must be entered regularly in the engine manufacturer's engine logbook:  Engine performance and speed  Air intake temperature  Exhaust gas temperature in front of and behind the turbine  Pressure of charge air  Pressure drop in charge air cooler  Lubricating oil pressure and lubricating oil temperature  Air temperature behind compressor and charge air cooler  Turbocharger speed  Pressure loss in air filter Servicing work according to the engine manufacturer's instructions  Clean or replace oil filter in supply line to turbocharger when engine is not running. 4.2.2 If provided 4.2.3 Oil filter

Operation 4 Servicing work 4.2 Page 45 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Service work every 15000 hours Inspection and assessment of the rotor and bearing parts as well as replacement of the variable turbine geometry module with a CPEX variable turbine geometry module must be carried out by an ABB Turbocharging Service Station.  It is recommended that the turbocharger is inspected once a year, but at least after every 15000 operating hours.  Disassemble turbocharger  Clearance measurement  Clean the turbine and compressor wheels and inspect for damage  Clean the turbine and compressor casings and inspect for any cracks and erosion or corrosion  Clean bearing casing and blow air through oil ports  Inspect and assess sealing air lines  Inspect and assess rotor and bearing parts  Have the variable turbine geometry module overhauled by ABB Turbo Systems. ABB Turbocharging Service Stations have variable turbine geometry modules replaced with overhauled ones as part of the CPEX (Customer Part Exchange) programme. Service work every 30000 hours The replacement of bearing parts as well as the inspection and assessment of the rotor must be carried out by an ABB Turbocharging Service Station.  Disassemble turbocharger.  Measure clearances.  Clean the turbine and compressor wheels and inspect for damage.  Clean the turbine and compressor casings and inspect for any cracks and erosion or corrosion.  Clean bearing casing and blow air through oil ports.  Inspect and assess rotor and bearing parts.  Replace bearings (original parts from ABB Turbo Systems). 4.2.4 4.2.5

Operation 4 Replacement intervals for turbocharger components 4.3 Page 46 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Replacement intervals for turbocharger components 4.3 The recommended replacement intervals for the compressor and turbine wheels due to stress caused by centrifugal forces and load cycles are calculated under consideration of the operating conditions while applying the safety concept for rotating components. They can be found on the turbocharger rating plate. Incalculable influencing parameters can shorten the recommended replacement intervals for the rotor, see Influencing parameters. The expected replacement intervals for non-rotating components and bearing parts are extremely dependent upon system-specific operating conditions, see Influencing parameters. When the specified, periodic inspections are carried out, the individual components are inspected for wear and tear and replaced if necessary. In this way, trouble-free operation is ensured. The following parameters influence the replacement intervals for turbocharger components: Parameters influencing bearing parts  Poor quality of the lubricating oil (lubrication oil filter system, condition of lubricating oil)  Unusual loads (vibration, start/stop frequency)  Non-permissible state of rotor unbalance Parameters influencing non-rotating components exposed to exhaust gas  Fuel quality (gas, MDO, HFO)  Load profile (thermal load changes, number of starts/stops)  Temperature level of exhaust gas  Turbine cleaning frequency  Procedure for turbine cleaning 4.3 Rotating components Non-rotating components Influencing parameters

Operation 4 Replacement intervals for turbocharger components 4.3 Page 47 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Parameters influencing rotating components exposed to exhaust gas  Fuel quality (gas, MDO, HFO)  Turbine cleaning frequency  Procedure for turbine cleaning  Load profile GAS / MDO Gas inlet casing 50000 … 100000 Gas outlet casing 50000 … 100000 Variable turbine geometry module (The variable turbine geometry module can be replaced with a CPEX variable turbine geometry module by an ABB Turbocharging service station.) 15000 Turbine diffuser / cover ring 35000 … 50000 Other casings 100000 Axial bearing components 24000 … 36000 Radial bearing components 24000 … 36000 Turbine blades (due to wear) - - Rotor components See the data on the rating plate GAS = Gas Engine MDO = Marine Diesel Oil NOTICE The specified values are guides and not guaranteed. (See Influencing parameters.) Expected replacement intervals [h] Recommended replacement intervals [h]

Operation 4 Speed measurement 4.4 Page 48 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Speed measurement 4.4 A speed measuring system permits continuous monitoring of the turbocharger speed. CAUTION Do not use cables as a climbing aid If you pull the speed measurement cables too hard, contacts can be pulled out.  Do not tension the speed measurement cables. Part number Description 42047 Screw plug 86505 Speed sensor 86515 Cable connector for 86505 86526 F/I converter 86528 Tachometer 4.4

Operation 4 Speed measurement 4.4 Page 49 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Speed differences with multiple turbochargers per engine The speeds of all turbochargers on one engine differ only slightly from each other in normal operation. The difference between the highest and the lowest turbocharger speed must not be more than 3 % relative to the speed limit nBmax. If this permissible range of difference is exceeded, the following steps must be carried out:  Reduce engine performance immediately until the highest turbocharger speed no longer exceeds 70% of nBmax.  If the engine cannot be stopped, continue to run at this reduced engine performance or turbocharger speed.  If the turbocharger surges continuously, engine performance must be reduced further.  Measure the temperatures in the air and gas lines to and from the turbochargers and compare them with standard values. If the engine can be stopped for a short time:  Inspect the air and gas lines as well as the turbocharger and eliminate any problems.  In any event, it is recommended that you contact the nearest ABB Turbocharging Service Station. 4.4.1

Operation 4 Speed measurement 4.4 Page 50 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Assembly If the speed sensor is not fitted on the turbocharger, the following procedure must be adopted to fit it:  Engine and turbocharger are not running.  The turbocharger lubricating system is switched off.  Remove screw plug (42047) from bearing casing. NOTICE Part position The position of the screw plug for measuring the speed is marked "n" on the bearing casing.  Screw in speed sensor (86505) as far as it will go and tighten to torque specified in table. (See chapter Table of tightening torques.)  Connect speed sensor using cable connector (86515). 4.4.2

Operation 4 Speed measurement 4.4 Page 51 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Replacing the speed sensor WARNING Hot cable connector and hot speed sensor Risk of burning. During operation, the cable connector and the speed sensor can reach temperatures exceeding 100 °C.  Wear safety gloves when removing the cable connector and speed sensor. Wear safety gloves against thermal risks.  Reduce engine performance to the idling speed, then stop the engine.  Switch off the lubricating oil supply to the turbocharger.  Disconnect the cable connector from the speed sensor.  Screw out defective speed sensor.  Screw in a new speed sensor up to the limit block.  Observe the tightening torque (see the table of tightening torques in the chapter entitled Disassembly and assembly). NOTICE Sealing the speed sensor The speed sensor is designed with a sealing lip and does not require an additional gasket when fitted.  Connect cable connector to speed sensor.  Switch on lubricating oil supply to turbocharger. Failure of speed measuring system Possible reasons for failure of the speed measuring system are described in the chapter Troubleshooting. 4.4.3 4.4.4

Operation 4 Emergency operation TPL..VA 4.5 Page 52 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Emergency operation TPL..VA 4.5 In the event of failure of the control system or the drive, the variable turbine geometry module can be fixed by clamping the ring lever (B) using at least 3 washers (C) spaced around the circumference. When fixing, the position of the variable turbine geometry module and / or the blades must be specified by the enginebuilder. 4.5 Detail A

Operation 4 Stopping the engine 4.6 Page 53 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Stopping the engine 4.6 CAUTION Stopping the engine Heat in the turbocharger must be dissipated by the further circulating lubricating oil.  Allow the engine to continue running at idling speed for a further 10 minutes before stopping. 4.6

Maintenance 5 Foreword to Maintenance 5.1 Page 55 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Maintenance Foreword to Maintenance 5.1 Maintenance and servicing work involves regular visual checks and cleaning to ensure that the turbocharger and its attached units function trouble-free.  The external condition and how dirty the cleaning points specified in this chapter are, must be established by visual checks at the specified intervals.  The safety precautions must be observed during all maintenance and servicing work. The cleaning points described in the following are:  Filter silencer  Compressor  Turbine and Guide Blades 5 5.1

Maintenance 5 Cleaning the filter silencer 5.2 Page 56 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Cleaning the filter silencer 5.2 Filter silencer and connecting rod 81265 Filter ring (if provided) 81136 Absorption segment 81269 Connecting rods 81137 Sheet-metal covering 81266 Cover grid 81135 Filter silencer body 81272 Screwdriver 81273 Lock nut E Insert unit = absorption segment + sheet­metal covering 5.2 5.2.1

Maintenance 5 Cleaning the filter silencer 5.2 Page 57 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Removing and cleaning filter silencer  Remove filter strip (81265).  Rinse filter strip (81265) using water with detergent additive or, if very dirty, soak it and squeeze out carefully. Rinse it in cold water. Avoid rough treatment (not a jet of water). NOTICE How dirty the filter strip (81265) is, depends on how clean the drawn-in air is. Clean filter strip every 500 hours of service or more frequently if necessary.  Unscrew and remove lock nuts (81273).  Unscrew and remove screws (81272) for connecting rods (81269).  Remove connecting rods (81269).  Carefully remove cover grids (81266).  Pull out insert units (E), bend open sheet-metal coverings (81137) and then remove absorption segments (81136).  Clean the absorption segments (81136). During cleaning, ensure that the absorption segments (81136) are only cleaned with a mild jet of compressed air, soft brush or a damp cloth. Otherwise there is a risk of damage or deformation. NOTICE Replace heavily contaminated or damaged parts with original parts from ABB Turbo Systems. If provided

Maintenance 5 Cleaning the filter silencer 5.2 Page 58 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Fitting the filter silencer  Assemble the insert units (E) by inserting the absorption segments (81136) into the sheet metal coverings (81137).  Bend sheet metal coverings (81137) back to original shape.  Insert the insert units (E) into slot guides in filter silencer unit (81135).  Uniformly place cover grids (81266) in correct position.  Push connecting rods (81269) through lugs of cover grids (81266). CAUTION If the connecting rods (81269) are not correctly positioned in their recesses on the filter silencer unit (81135), the cover grid (81266) can twist and shift. There is then a risk of foreign matter and contamination getting into the compressor.

Maintenance 5 Cleaning the filter silencer 5.2 Page 59 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C  Join connecting rods (81269) using screws (81272). When tightening the screws (81272), ensure that connecting rods (81269) are located correctly in recesses in filter silencer body (81135). Now tighten screws (81272) alternately until the following maximum torque is reached: Screw Tightening torque [Nm] 81272 20  Screw lock nuts (81273) onto screw (81272) and tighten to following torque: Lock nut Tightening torque [Nm] 81273 40  Fit filter strip (81265). If provided

Maintenance 5 Cleaning the compressor during operation 5.3 Page 60 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Cleaning the compressor during operation 5.3 NOTICE These instructions for wet cleaning apply only when cleaning is carried out with clean water and the enginebuilder permits the process. The degree of contamination of the compressor stage (compressor wheel and diffuser) depends on how clean the drawn-in air is. Deposits of dirt can build up in the flow channels if the following substances are in the intake air:  Oily or salty mist  Solid combustion residues  Various kinds of dust Contamination of the compressor stage has a negative influence on the compressor efficiency and the charging pressure. This results in higher exhaust gas temperatures and higher fuel consumption by the engine. Contamination of the compressor can also increase rotor unbalance. Under no circumstances is periodic cleaning of the compressor during operation a substitute for the service work carried out when the turbocharger is completely dismantled and the compressor is cleaned mechanically. The interval between periodic cleaning is very dependent on the operating conditions. In general, cleaning should be carried out every 25 to 100 operating hours. NOTICE Cleaning intervals Should the specified cleaning intervals prove incompatible with engine operation, please contact ABB Turbo Systems. 5.3 Cleaning interval

Maintenance 5 Cleaning the compressor during operation 5.3 Page 61 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Cleaning method Cleaning of the compressor during operation is carried out using the cleaning method described in the following:  Wet cleaning This cleaning method has been tested and approved by ABB Turbo Systems. To clean the compressor stage during operation, water is injected in front of the compressor wheel through an injection pipe fitted in the filter silencer or the suction branch. The water does not act as a solvent, but the dirt deposit is removed by the mechanical impact of the droplets. This is a very suitable process, provided that the degree of contamination is not too high. CAUTION Corrosion and deposits when cleaning Damage and impairment of turbocharger parts due to salt water and cooling water additives  Don't use salt water for cleaning, but only clean fresh water. In the case of V-engines with several turbochargers on each engine, we recommend parallel cleaning of the compressors. This cleaning process is faster and the risk of turbocharger surging is reduced. Principle of wet cleaning V-engines

Maintenance 5 Cleaning the compressor during operation 5.3 Page 62 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Wet cleaning with orifice plate on filter silencer (XC2) Operating state prerequisites for cleaning compressor with XC2 NOTICE To be able to carry out a satisfactory cleaning process which has been tested and is recommended by ABB Turbo Systems, the following prerequisites must be fulfilled:  Engine load 50 ... 85%  Start of cleaning cycle in accordance with following description of wet cleaning operation with XC2. Compressor wet cleaning operation with XC2  Maintain water pressure before connection to turbocharger (during water injection time) must be maintained as shown in table Cleaning parameters.  After cleaning, wait at least 5 minutes to allow turbocharger to dry. NOTICE If the cleaning process is unsatisfactory, it can be repeated up to 2 times. If the cleaning result is still not satisfactory after three attempts and the engine values are also unsatisfactory, we recommend that you have the turbocharger inspected and cleaned by an official ABB Turbocharging Service Station. Cleaning parameters per turbocharger compressor Product Engine load Water pressure [bar] Water injection time [sec] Orifice diameter [mm] TPL65VA32/33 50 … 85% 3 10 2.1 5.3.1

Maintenance 5 Cleaning the compressor during operation 5.3 Page 63 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Wet cleaning using external water-pressure vessel (XC3) Operating state prerequisites for compressor cleaning with XC3 NOTICE To be able to carry out a satisfactory cleaning process which has been tested and is recommended by ABB Turbo Systems, the following prerequisites must be fulfilled:  Engine load 50 ... 85%  Start of cleaning cycle in accordance with following description for wet cleaning operation with XC3. Compressor wet cleaning procedure with XC3  It is mandatory to fulfil the operating condition prerequisites before cleaning compressors with XC3.  Remove the sealing plug (X).  Fill the vessel with the required volume of clean water (see the Table of cleaning parameters). 5.3.2 Operating the water pressure vessel

Maintenance 5 Cleaning the compressor during operation 5.3 Page 64 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C  Screw in the sealing plug (X).  Push the valve activator (Y) against the spring and hold it for 10 ... 15 seconds until the entire volume of water has been injected.  After cleaning, wait at least 5 minutes to allow the turbocharger to dry. NOTICE If the cleaning operation is not satisfactory, it may be repeated up to two times. If the cleaning results are still not satisfactory after three attempts and the engine values are also unsatisfactory, we recommend that you have the turbocharger inspected and cleaned by an official ABB Turbocharging Service Station. Cleaning parameters per turbocharger compressor Product Engine load Contents of water vessel [dm3] TPL65 50 … 85% 0.4

Maintenance 5 Cleaning turbines and guide vanes during operation 5.4 Page 65 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Cleaning turbines and guide vanes during operation 5.4 NOTICE HFO applications The TPL65VA.. has not been released for HFO applications. Wet cleaning of the turbine blades and guide vanes during operation is thus neither required nor planned. 5.4

Troubleshooting 6 Malfunctions when starting 6.1 Page 67 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Troubleshooting Malfunctions when starting 6.1 Sluggish start-up Possible causes Elimination Turbo- charger Turbocharger contaminated Clean it Damaged bearing Contact an ABB Turbocharging Service Station Rubbing rotor Foreign object in turbocharger Vibrations Possible causes Elimination Turbo- charger Rotor unbalance Contact an ABB Turbocharging Service Station Damaged turbine or compressor Damaged bearing Rubbing of rotating parts Normal behaviour, no malfunction Turbo- charger Minor uniform wear around the periphery of rotor components, caused by slight local rubbing of adjacent components, is permissible. The compressor blades and turbine blades are then shortened somewhat. Certain tolerances must be observed to avoid a significant loss of efficiency.  If there is any doubt about the extent of rubbing, then an ABB Turbocharging Service Station must be contacted.  Have a dimension check carried out by an ABB Turbocharging Service Station. 6 6.1

Troubleshooting 6 Surging of the turbocharger 6.2 Page 68 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Surging of the turbocharger 6.2 Turbocharger surging Possible causes Elimination Engine Guard in front of the turbocharger is contaminated or damaged Clean / replace it Turbocharger Filter silencer or diffuser contaminated Clean it Heavy deposits of dirt in the turbine or nozzle ring Charge air cooler Cooler contaminated Clean it Charge air duct blocked CAUTION Prolonged or periodic surging Possible damage to components, such as the compressor wheel, turbine blades, bearings and filter silencer  Have the cause clarified immediately by an ABB Turbocharging service station and rectified.  Have components inspected for damage and, if necessary, replaced by an ABB Turbocharging service station. Sporadic surge blows Surging of the turbocharger can occur during certain operating conditions such as when reducing the engine performance quickly when manoeuvring. At the same time, the flow direction in the compressor is momentarily reversed. Such sporadic surge blows do not impair the safe operation of the turbocharger.  A surge blow is accompanied by a loud bang and escape of hot air from the filter silencer. 6.2

Troubleshooting 6 Malfunctions during operation 6.3 Page 69 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Malfunctions during operation 6.3 Lubricating oil pressure too low Possible causes Elimination Engine Oil filter heavily contaminated Clean it Defective oil pump in lubricating system Check / replace it Manometer display wrong Replace the manometer Turbo- charger Rotor axial clearance too large Contact an ABB Turbocharging Service Station Reduction in speed Possible causes Elimination Engine Defects of connected cylinders when pulse charging Contact the enginebuilder Turbo- charger Heavy contamination of the turbine Clean it Damaged rotor components or bearing Contact an ABB Turbocharging Service Station Pipes Defects such as leaks in the exhaust gas pipes or charge air ducts Make repairs Increase in speed Possible causes Elimination Turbo- charger Heavily contaminated nozzle ring (with 4-stroke application) Contact an ABB Turbocharging Service Station 6.3

Troubleshooting 6 Malfunctions during operation 6.3 Page 70 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Exhaust gas temperature too high Engine performance and engine speed unchanged Possible causes Elimination Engine Malfunctioning injection system Repair it or contact the manufacturer Turbocharger Air starvation, for example filter silencer clogged with dirt Clean it Compressor / turbine contaminated Exhaust counterpressure too high Clean or repair the boiler or exhaust silencer Damaged or eroded turbine Contact an ABB Turbocharging Service Station Charge air cooler Cooler contaminated Clean it Cooling water volume too low Top up the water Entry temperature of cooling water too high Inspect / clean the cooling system Inadequate ventilation Improve the ventilation

Troubleshooting 6 Malfunctions during operation 6.3 Page 71 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Charge air pressure too low Engine performance and engine speed unchanged, air intake condition normal Possible causes Elimination Engine Air receiver leaking Make repairs Gas piping between the engine and the turbine leaking Poorly adjusted injection system Correct it Poorly adjusted valve control Turbo- charger Manometer display wrong Replace the manometer Line to manometer leaking Repair the leak Contaminated filter silencer causing excessive loss of pressure Clean it Compressor / turbine contaminated Damaged compressor / turbine Contact an ABB Turbocharging Service Station Exhaust counterpressure too high Clean or repair the boiler or exhaust silencer Charge air pressure too high Engine performance and engine speed unchanged, air intake condition normal Possible causes Elimination Engine Malfunctioning injection system Repair it or contact the manufacturer Poorly adjusted injection system Correct it Engine performance higher than expected Check engine performance Turbo- charger Manometer display wrong Replace the manometer

Troubleshooting 6 Malfunctions when stopping 6.4 Page 72 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Malfunctions when stopping 6.4 Noises during run-down Possible causes Elimination Turbo- charger Turbocharger contaminated Clean it Damaged bearing Contact an ABB Turbocharging Service Station Rubbing rotor Foreign object in turbocharger Run-down time too short Possible causes Elimination Turbo- charger Turbocharger contaminated Clean it Damaged bearing Contact an ABB Turbocharging Service Station Rubbing rotor Foreign object in turbocharger 6.4

Troubleshooting 6 Speed measurement system 6.5 Page 73 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Speed measurement system 6.5 Possible causes Elimination Signal amplitude non existent or poor Fitting error The screw plug for the sensor is fitted with a gasket. When fitting the speed sensor, this gasket must be removed. If it is fitted by mistake, the distance from the sensor tip to the signal-generating sealing disc increases. As a result, the voltage amplitude of the speed signal decreases, which can cause problems for the evaluation electronics. This problem is eliminated by removing the gasket. Defective sensor Contact ABB Turbocharging service station. Measured speeds too high Dirty sensor tip The sensor tip is magnetic and can thus attract metal particles. As a result, the distance to the auxiliary bearing decreases, which can lead to amplification of the noise component and consequently to faulty triggering. Remove the sensor, clean its tip and refit the sensor using the specified tightening torque. Measured speed too low - - Contact ABB Turbocharging service station. Other sources of errors - - If none of the above measures eliminates the problem, we recommend that you have the speed measuring system inspected by an official ABB Turbocharging service station. 6.5

Troubleshooting 6 Variable Turbine Geometry 6.6 Page 74 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Variable Turbine Geometry 6.6 Variable Turbine Geometry (VTG) not adjustable Possible causes Elimination Turbocharger Heavy turbine contamination Contact an ABB Turbocharging Service Station VTG bearing damaged Drive unit (electrical components) No drive energy Contact an ABB Turbocharging Service Station 6.6

Removal and installation 7 Turbocharger weights 7.1 Page 75 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Removal and installation Turbocharger weights 7.1 Lifting gear with a sufficient load limit must be used for removing and installing the turbocharger. The following weight specification is the heaviest possibility. This guide value can differ from data on the rating plate, depending on the specification. TPL65VA32/33 1210 7 7.1 Weight [kg]

Removal and installation 7 Removing the turbocharger 7.2 Page 76 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Removing the turbocharger 7.2  Disconnect all gas, air and oil lines in accordance with engine manufacturer’s instructions. CAUTION Oil orifice plates An orifice plate for adjusting the oil pressure is fitted in each of the two oil inlet channels in the bearing casing. When the cartridge group, the bearing casing or the turbocharger is fitted to the engine, it must be ensured that the orifice plates that are specified for the turbocharger have been installed in the two oil inlet channels.  Check correct installation of oil orifice plates.  Unplug the cable connector on the speed sensor.  Remove the insulation at the suspension ribs. TPL65: Version with compressor wheel cooling system  Remove air supply line. (See also chapter entitled Preliminary remarks / Layout and functionality)  Inspect the lifting gear.  Fasten separate lifting gear to each of the two ribs on the bearing casing provided for this purpose. 7.2

Removal and installation 7 Removing the turbocharger 7.2 Page 77 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C  Ribs (01) not in the middle at the top:  Completely remove the bearing casing insulation (02) and place a sling around the bearing casing.  Loosen the fixing screws at the foot.  Lift the turbocharger off the engine and set it down to one side. WARNING Beware of tilting If support for the turbocharger is not provided or is inadequate, the turbocharger could tip over during installation or removal and cause a serious or even fatal injury.  Support the turbocharger at a suitable point.  If possible secure it using lifting gear. Wear safety helmet.  Cover the oil connection.

Removal and installation 7 Installing the turbocharger 7.3 Page 78 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Installing the turbocharger 7.3  Remove cover from oil connection.  Inspect lifting gear.  Fasten separate lifting gear to each of two bearing casing ribs provided for this purpose. CAUTION Oil orifice plates An orifice plate for adjusting the oil pressure is fitted in each of the two oil inlet channels in the bearing casing. When the cartridge group, the bearing casing or the turbocharger is fitted to the engine, it must be ensured that the orifice plates that are specified for the turbocharger have been installed in the two oil inlet channels.  Check correct installation of oil orifice plates.  Adapt turbocharger to suit engine.  Tighten fixing screws in foot in accordance with engine builder's instructions.  Fasten gas, air and oil lines in accordance with engine builder’s instructions. TPL65: Version with compressor wheel cooling system  Fit air supply line. (See also chapter Preliminary remarks / Layout and functioning.)  Refit removed parts of insulation.  Plug in cable connector on speed sensor. 7.3

Disassembly and assembly 8 Introduction 8.1 Page 79 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Disassembly and assembly Introduction 8.1 CAUTION Further work Further tasks, which are not described here, may be carried out only by trained personnel from an ABB Turbocharging service station.  Only carry out those tasks that are described in this chapter. NOTICE Marking casing positions for assembly ABB Turbo Systems recommends that the casing positions are marked before disassembling the turbocharger. Identifying assembly devices Not all assembly devices are marked with a part number. They can be identified using the tool list. This list is enclosed in the toolbox. WARNING Maintaining assembly devices Assembly devices must be checked for damage before and after use.  Visually check for corrosion, cracks, deformation and wear.  Don't use damaged assembly devices, but replace them. Customer spare parts set Before beginning work, ensure that the required customer spare parts sets are available.  See chapter Spare parts. 8 8.1

Disassembly and assembly 8 Introduction 8.1 Page 80 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Tightening torques for turbocharger components The specified tightening torques of screw connections for turbocharger components must be observed. (See section Table of tightening torques.) Tightening torques for assembly devices of ABB Turbo Systems If nothing else is described, the screws and nuts of the assembly devices must be tightened down firmly. WARNING Suspended loads Loads not suspended in compliance with regulations may lead to personal injury or accidents with fatal consequences.  Attach turbochargers, assemblies or individual components only to lifting gear which is in technically perfect condition and has sufficient load capacity.  Make sure the load is suspended properly on the crane hook.  Do not let anyone stand beneath a suspended load. Wear safety gloves against mechanical risks. Wear safety helmet. Definition of terms  Suspension point Defined load carrying point on a component or an assembly (blind hole thread, eye, lug).  Assembly device Devices mounted on the turbocharger to create a suspension point. Assembly devices are calculated and designed especially for the defined application. They are not commercially available products. Use assembly / fitting devices only for the applications described.  Lifting gear Equipment for lifting and transporting loads (ropes, chain hoists, cranes). Lifting gear is not supplied by ABB Turbo Systems.

Disassembly and assembly 8 Module weights 8.2 Page 81 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Module weights 8.2 The specified weights of individual parts or assemblies are guides rounded off to the next highest value. Assemblies Description TPL65VA32/33 01 Radial air suction branch 50 02 Axial air suction branch 35 03 Filter silencer 130 04 Compressor casing 180 05 Wall insert 40 06 Diffuser 19 07 Cartridge group 290 08 Turbine diffuser 30 09 Variable turbine geometry module 55 10 Radial gas inlet casing 50 8.2 Weights [kg]

Disassembly and assembly 8 Module weights 8.2 Page 82 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Complete compressor casing TPL65VA32/33 240 NOTICE The total weight of the complete compressor casing is an addition of the weights of the compressor casing, the diffuser and the wall insert. Weight [kg]

Disassembly and assembly 8 Removing and fitting filter silencer or air suction branch 8.3 Page 83 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Removing and fitting filter silencer or air suction branch 8.3  Remove insulation where necessary.  Pass lifting gear through rib on filter silencer.  Pass lifting gear through lugs on back.  Unscrew nuts (72027) and remove them together with washers (72018).  Remove filter silencer and set it down to one side.  Install filter silencer in reverse order. 8.3 Removing the filter silencer Installing the filter silencer

Disassembly and assembly 8 Removing and fitting filter silencer or air suction branch 8.3 Page 84 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C  Disconnect all air lines in accordance with the engine builder’s instructions.  Dismantle the insulation where necessary.  Pass a lifting gear around the air suction branch. It is permissible to pass the lifting gear through holes possibly provided in the ribs to improve stability.  Unscrew the nuts (72027) and remove them together with the washers (72018).  Remove the air suction branch and set it down to one side.  Fit the air suction branch in reverse order. Removing the air suction branch Installing the air suction branch

Disassembly and assembly 8 Axial clearance 8.4 Page 85 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Axial clearance 8.4 WARNING Physical hazards due to sharp edges on compressor wheel The compressor wheel has sharp edges which can result in injury.  Wear safety gloves. Wear safety gloves against mechanical risks.  The axial clearance (A) must be measured before removing and after fitting the cartridge group.  Measure and note the axial clearance (A). TPL65VA32/33 0.31 … 0.49 CAUTION Clearances out of tolerance Clearances out of tolerance and excessively worn components can be the cause of serious damage to machinery and property.  Have components assessed and, if necessary, replaced by an ABB Turbocharging Service Station. 8.4 Clearance A [mm]

Disassembly and assembly 8 Removing cartridge group 8.5 Page 86 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Removing cartridge group 8.5  Remove insulation. Version with compressor wheel cooling system  Remove air supply line. (See also chapter entitled Preliminary remarks / Layout and functionality)  Disconnect oil pipes in accordance with enginebuilder's instructions. CAUTION Oil orifice plates An orifice plate for adjusting the oil pressure is fitted in each of the two oil inlet channels in the bearing casing. When the cartridge group, the bearing casing or the turbocharger is fitted to the engine, it must be ensured that the orifice plates that are specified for the turbocharger have been installed in the two oil inlet channels.  Check correct installation of oil orifice plates.  Loosen and remove sealing air line (56501) between compressor casing (72000) and variable turbine geometry module (56100).  Remove three studs (72029) at top.  Attach lifting device (90190) to compressor casing (72000), then fasten and secure it to crane using lifting gear.  Unscrew nuts (61037).  Uniformly press apart compressor casing (72000) using three press-off nuts (61090).  Slightly lift compressor casing (72000) and withdraw it. 8.5

Disassembly and assembly 8 Removing cartridge group 8.5 Page 87 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C  Turn the compressor casing (72000) together with the wall insert and diffuser and set them down with surface (F) on an underlay. WARNING Tipping the compressor casing Make sure the underlay does not shift.  Allow the compressor casing to rest only on surface (F).  Check the underlay and adjust it if necessary.  Remove the screws (72002).  Remove the diffuser (79000).  Remove the wall insert (77000) using swivel lifting eyes (90235).  Remove the O-ring (77005) from the wall insert.

Disassembly and assembly 8 Removing cartridge group 8.5 Page 88 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C  Unplug the cable connector (86515) and screw out the speed sensor (86505) complete with the O-ring (86506).  Remove the O-ring (42012).  Remove the three screws (61059) and Verbus Ripp® washers (61058).  Fasten separate lifting gear to each of the two ribs on the bearing casing provided for this purpose.  Uniformly press off the cartridge group using the press-off screws (90900) in the holes provided. CAUTION If the rotor blades have insufficient or no clearance, the blades and casing could be damaged.  Turn the rotor to check that the blades do not rub against the turbine diffuser.

Disassembly and assembly 8 Removing cartridge group 8.5 Page 89 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C  Withdraw the cartridge group and fit the supports (90450).  Cover the oil connections.

Disassembly and assembly 8 Removing and fitting turbine diffuser 8.6 Page 90 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Removing and fitting turbine diffuser 8.6  Replace two screws (61032) with two studs (90903) in upper section of turbine diffuser.  Screw out the remaining screws (61032), press off the turbine diffuser (63000) using the press-off screws (90901), then withdraw and remove it. Fitting the turbine diffuser  Fit the turbine diffuser in reverse order of removal. NOTICE Brush high-temperature grease on all screws at and in the gas outlet casing. 8.6

Disassembly and assembly 8 Removing variable turbine geometry module with gas inlet casing 8.7 Page 91 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Removing variable turbine geometry module with gas inlet casing 8.7  Disconnect semi-circular section of sealing air line (A) from variable turbine geometry module.  Retaining clips (56121) are fitted.  Unscrew nuts (61042).  Remove gas inlet casing (51001) together with variable turbine geometry module (56100). CAUTION After removing screws (56122) and retaining clips (56121), gas inlet casing (51001) is no longer secured.  Loosen screws (56122) together with retaining clips (56121) and remove with clamping ring (56112).  Remove clamping ring (56112).  Carefully separate gas inlet casing (51001) from variable turbine geometry module (56100) and remove it. CAUTION Have the variable turbine geometry module overhauled by ABB Turbo Systems. ABB Turbocharging Service Stations have variable turbine geometry modules replaced with overhauled ones as part of the CPEX (Customer Part Exchange) programme. 8.7

Disassembly and assembly 8 Fitting the variable turbine geometry module and the gas inlet casing 8.8 Page 92 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Fitting the variable turbine geometry module and the gas inlet casing 8.8  Push variable turbine geometry module (56100) over studs  Push gas inlet casing (56001) over studs  Slide clamping ring (56112) onto studs  Tighten nuts (61042) to specified torque  Fit retaining clips (56121) using screws (56122)  Fit semi-circular section of sealing air line (A) to variable turbine geometry module 8.8

Disassembly and assembly 8 Fitting the variable turbine geometry module and the gas inlet casing 8.8 Page 93 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C  Fit sealing air line (56501) to semi-circular section of line (A).

Disassembly and assembly 8 Installing cartridge group 8.9 Page 94 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Installing cartridge group 8.9 CAUTION Oil orifice plates An orifice plate for adjusting the oil pressure is fitted in each of the two oil inlet channels in the bearing casing. When the cartridge group, the bearing casing or the turbocharger is fitted to the engine, it must be ensured that the orifice plates that are specified for the turbocharger have been installed in the two oil inlet channels.  Check correct installation of oil orifice plates.  Remove the cover from the oil connection.  Fasten separate lifting gear to each of the two ribs on the bearing casing provided for this purpose.  Remove the supports (90450) and carefully insert the cartridge group.  Uniformly tighten the screws (61059) together with the Verbus Ripp® washers (61058). 8.9

Disassembly and assembly 8 Installing cartridge group 8.9 Page 95 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C CAUTION If there is no or insufficient clearance between the rotor turbine blades and the turbine diffuser, the blades and the turbine diffuser (casing) can be damaged.  Turn the rotor to check that the blades do not rub against the turbine diffuser.  Remove the lifting gear.  Fit the O-ring (42012).  Screw in the speed sensor (86505) along with the O-ring (86506) and plug in the cable connector (86515).  Fit the O-ring (77005) to the wall insert (77000).  Fit the lifting gear and the swivel lifting eye (90235).  Align and fit the wall insert (77000) using the centring screw (90187).  Place the diffuser (79000) in position using the swivel lifting eye (90235).  Remove the swivel lifting eye (90235).  Fit the screws (72002).

Disassembly and assembly 8 Installing cartridge group 8.9 Page 96 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C  Attach lifting gear to lifting device (90190) and turn compressor casing (72000).  By hand, screw three press-off nuts (61090) onto bearing casing studs, equally spaced around circumference and up to end of thread.  Push compressor casing (72000) onto cartridge group to fit snugly and fasten it using nuts (61037).  Secure three press-off nuts (61090) against compressor casing (72000) by tightening them to specified torque. (See chapter Table of tightening torques.)  Remove lifting device (90190).  Fit sealing air line (56501) between compressor casing (72000) and variable turbine geometry module (56100).

Disassembly and assembly 8 Installing cartridge group 8.9 Page 97 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C  Measure and note the axial clearance (A) (see the section on axial clearance). CAUTION Clearances out of tolerance Clearances out of tolerance and excessively worn components can be the cause of serious damage to machinery and property.  Have components assessed and, if necessary, replaced by an ABB Turbocharging Service Station.  Connect oil pipes and all air lines in accordance with engine builder’s instructions. Version with compressor wheel cooling system  Fit the air supply line. (Also see the chapter Preliminary remarks / Layout and functioning.)  Fit the filter silencer or air suction branch.  Fit the insulation.

Disassembly and assembly 8 Table of tightening torques 8.10 Page 98 © Copyright 2015 ABB. All rights reserved. September 2015 HZTL2464_EN Revision C Table of tightening torques 8.10 8.10