Mircom TX3-T-KIOSK3 Assembly Manual

Printed in Canada Subject to change without prior notice LT-6123 rev 1 For more details, see LT-996 and LT-969 on the Mircom website and the USB fl ash. Mircom technical support: 1-888-647-2665 The stand mounts to the fl oor inside the building near the entrance, close to the building power source and telephone infrastructure. Access for the power and communication cables is provided through a cutout in the fl oor bracket. ATTACH THE FLOOR BRACKET TO THE FLOOR ASSEMBLING TX3-T-KIOSK3 Figure 1: Stand Dimensions Figure 2: Components of the Kiosk stand 1 1. Ensure that the fl oor bracket is aligned with the electrical conduit. 2. Using the fl oor bracket as a template, trace an opening on the fl oor for the cutout and mark the 6 fl oor bracket mounting hole locations as shown in Figure 3. 3. Cut an opening in the fl oor for the electrical and communication cables. 4. Run the wires through the fl oor bracket opening. 5. Secure the fl oor bracket to the fl oor using 6 bolts through the fl oor bracket mounting holes shown in Figure 3. The holes are 13/32” (10 mm) in diameter. Figure 3: Floor bracket mounting holes Figure 4: TX3-T-KIOSK3 dimensions (from below) 23 1/4” (591 mm) 61 11/32” (1558 mm) 15 1/4” (387 mm) Mircom 25 Interchange Way Vaughan (Toronto), Ontario L4K 5W3 Canada Technical Support: 888-647-2665 General Inquiries: 1-888-660-4655 US Address: 4575 Witmer Industrial Estates Niagara Falls NY 14305 Attention: The stand is heavy. Never attempt to lift this product by yourself. At least two people should lift it together. To ensure that there is enough room for installing the stand, leave at least 4” (102 mm) clearance between the back of the fl oor bracket and the wall. To ensure that there is enough room for opening the door after the stand is installed, leave at least 25” (635 mm) clearance between the back of the fl oor bracket and the wall. Avoid placing the Touch Screen in direct sunlight. Install the power supply outside the enclosure. The kit includes: 1 x pedestal 1 x fl oor bracket 1 x door 6 x #8-32 x 1/4 screws for attaching the Touch Screen 12 x #1/4-20 x 5/8 screws for attaching the stand to the fl oor bracket 2 x keys Weight: 74 lb (34 kg) You need: 6 bolts to attach the fl oor bracket to the fl oor. The bolts must fi t holes that are 13/32” (10 mm) in diameter. Front Back Front Back 6 19/64” (160 mm) Ø 2” (51 mm) 8 11/64” (207 mm) 9” (228 mm)

Printed in Canada Subject to change without prior notice LT-6123 rev 1 For more details, see LT-996 and LT-969 on the Mircom website and the USB fl ash. Mircom technical support: 1-888-647-2665 FIT THE STAND ON THE FLOOR BRACKET Attention: The stand is heavy. Never attempt to lift this product by yourself. At least two people should lift it together. 1. Place the stand on the fl oor bracket, and slide it forwards so that it rests on top of the fl oor bracket. 2. Ensure that the fl oor bracket fi ts into the back lip of the stand. 3. Secure the stand onto the fl oor bracket using the 12 screws as show in Figure 7. Figure 6: The stand on the fl oor bracket (from below) Figure 7: Attach the stand to the fl oor bracket Figure 5: Fit the stand on the fl oor bracket 2 3 ATTACH THE TOUCH SCREEN TO THE STAND 1. Fit the Touch Screen on the six studs on the stand. 2. Attach the 6 included screws to the studs. 3. Run the wires through the knockout at the bottom of the Touch Screen. Figure 8: Attach TX3-TOUCH-F22 to the stand ASSEMBLING TX3-T-KIOSK3 ATTACH THE DOOR 4 1. Fit the door into the opening so that it rests on the ledge. 2. Swing the door down and lock it. Close-up showing the door fi tting on the ledge Figure 9: Fit the door on the stand Figure 10: Swing the door closed Note: Use only the 22 inch fl ush mount Touch Screen (TX3-TOUCH-F22) with this stand. Attention: The 22” Touch Screen enclosure is heavy. Never attempt to lift this product by yourself. At least two people should lift it together.