Enclume PR33 Instructions

PR33 Enclume racks are the ultimate in Quality, design, strength and function. Congratulations for owning one of the finest Storage racks made. WARNING: READ ALL OF THE INSTRUCTIONS BEFORE ASSEMBLING AND USING YOUR RACK. All of our hammered steel racks are finished with an industrial wax designed to give years of protection to the rack. Cleaning is easily done with a damp cloth. Dry thoroughly after cleaning. If a touch-up is ever needed we recommend a "Pledge" like wax product. Enclosed you will find everything needed for the assembly and use of your storage rack. Two people make assembly and installation easier. The parts and hardware included are: Hardware included: 4 – 3/8” x 3/4” Button Head Screws 2 – 3/8” x 1” Button Head Screws 6 –3/8” Nuts 2 – Ceiling Screw Hooks (Large) 2 – 5” Extension Hooks 1 – 7/32” Allen Wrench 12 – Angled Pot Hooks 12 – Straight Pot Hooks 2 – Grid Brackets Toggle Kit Components included: 1 – Oval Base 1 – Grid 4 – Arms 1 – Upper 4 – “L” shaped Grid Brackets See reverse side for ASSEMBLY AND INSTALLATION INSTRUCTIONS Limited Warranty:This product is warranted to be free of material defects for a period of five years from the date of purchase. Customer's exclusive remedy shall be the repair or replacement of the defective product and shall be subject to the following conditions: (1) notice of any defect is received by Enclume within the warranty period and (2) customer returns the defective product to Enclume Design Products, Inc. , 24 Colwell St.. , Port Hadlock, WA 98339, postage prepaid within 20 days following a return authorization number (which may be obtained by telephoning the number at the bottom of this instructions) being provided to the customer by Enclume. There are no other warranties, expressed or implied. THERE ARE NO WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. ENCLUME SPECIFICALLY DISCLAIMS ANY AND ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE PURCHASE OR USE OF ENCLUME'S PRODUCTS. ::potracks.com Call 1-800-667-8721 anywhere in the US and Canada - www.kitchensource.com ::potracks.com powered by ::kitchensource.com

Hardware included: 4 – 3/8” x 3/4” Button Head Screws 2 – 3/8” x 1” Button Head Screws 6 –3/8” Nuts 2 – Ceiling Screw Hooks (Large) 2 – 5” Extension Hooks 1 – 7/32” Allen Wrench 12 – Angled Pot Hooks 12 – Straight Pot Hooks 4 – “L” shaped Grid Brackets Toggle Kit Components included: 1 – Oval Base 1 – Grid 4 – Arms 1 – Upper Rack Assembly 1) If your rack is stainless steel it is best to keep the tissue on during installation to avoid fingerprinting. 2) Place rack body (also called the oval) on the floor or other “firm” surface. 3) Attach the four arms to the OUTSIDE of the oval using the 3/8” x 1/4” button head screws. From the outside, thread the button head through the arms, the oval and grid bracket (long side down). Secure with 3/8” Hex nut. Make sure the arm orientation is correct. The 90 degree bend is facing towards the center of the rack and is approximately even with the bottom of the rack body. Leave the four button head screws slightly loose. 4) Attach the upper bar to the four arms using the two longer screws, and two nuts. Insert the extension hooks into the holes in the upper bar. 5) Square up the arms and tighten all the screws with the Allen wrench. The assembly is now complete. 6) Carefully place the grid (from one end) between the arms until it fits into the oval and rests on the arm tabs for support. Two people make this step easier. 7) We recommend that you anchor your rack into the solid wood of ceiling joists or beams. Carefully measure the area where the rack is to be hung and install the ceiling screw hooks directly into the wood joists. If it is not convenient to hang your rack directly into wood joists you may use the new-technology DRYWALL anchors enclosed with your rack. The steel anchors are very strong and when installed in drywall will hold 200 lbs. each. Two anchors hold about 400 lbs. Follow the instructions in the Toggler kit. 8) Hang your heavier items on the straight portion of the rack between the hanging arms or from the upper bar between the extension hooks. 9) All of our hammered steel racks are finished with an industrial wax designed to give years of protection to the rack. Cleaning is easily done with a damp cloth. Dry thoroughly after cleaning. If a touch-up is ever needed we recommend a "Pledge" like wax product. 10) The grid has been treated with a finish which will resist corrosion and tarnish. It can be cleaned with a damp cloth and dried thoroughly. Please do not use abrasive cleaners. It is important that your rack is assembled correctly. If the unit is assembled or used incorrectly, it could become unstable and collapse, possibly causing injury. WARNING ::potracks.com Call 1-800-667-8721 anywhere in the US and Canada - www.kitchensource.com ::potracks.com powered by ::kitchensource.com