Crux DKFD-60L Manual 

with Dash Kit for FORD, LINCOLN & MERCURY Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311 phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com rev.051619 1 of 7 - Retains factory features with an aftermarket radio. - Retains factory-installed Subwoofer. - Retains Steering Wheel Controls via built-in, pre-programmed interface. - With navigation outputs (Reverse gear, Illumination and Speed signal). - Provides Accessory Power (2A MAX). - Includes dask kit (double DIN or single DIN with pocket). PRODUCT FEATURES: PARTS INCLUDED: SWRFD-60L MODULE SWRFD-60L HARNESS Antenna Adapter SWC CABLE SWC 3.5MM PLUG ADAPTER

with Dash Kit for FORD, LINCOLN & MERCURY Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311 phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com rev.051619 2 of 7 INSTALLATION DIAGRAM: AFTERMARKET RADIO +12V Constant Yellow +12V ACC Red 12V Ground Black Illumination Orange Vehicle Speed Sense Red/White (or Brown) Subwoofer Amp Turn-on Blue/White Antenna Turn-on Blue Right Front (+) Gray Right Front (-) Gray/Black Left Front (+) White Left Front (-) White/Black Right Rear (+) Violet Right Rear (-) Violet/Black Left Rear (+) Green Left Rear (-) Green/Black Subwoofer Factory Aux Input 24-Pin Plug* 16-Pin Plug* 8-Pin Plug* TO FACTORY HARNESS 12-Pin Connector SWC TYPE (Connect PINK to PINK wire) Subwoofer Converter Module *Inspect that the male pins are properly lined up before plugging into the factory harness. SWRFD-60L MODULE ON RADIO VEHICLE 1 2 3 4 5 6 7 8 AFTERMARKET RADIO SELECTOR (See Chart) FORD SWC SETTING (OFF OFF OFF OFF) ON RADIO VEHICLE 1 2 3 4 5 6 7 8 Cap or insulate if not being used Kenwood/JVC (BLUE / YELLOW) Insulate with tape if not being used 3.5MM SWC CABLE Plug in the 3.5MM SWC cable to the 4-pin port on the module. See “DIP SWITCH SETTINGS” section. LIN BUS (Green) Blue/Yellow (Not Used) 1. Only supports analog Steering Wheel Control type. 2. Use part number SWRFD-60 for CAN Bus Steering Wheel Control. 3. Output signal stated above may not cover all Year/Model. 4. Does not retain SYNC. 5. Not compatible with factory-installed Sony systems and THX systems with amplifier. NOTES:

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com rev.051619 3 of 7 DKFD-60L Radio Replacement Interface with Steering Wheel Control Retention with Dash Kit for FORD, LINCOLN & MERCURY ANALOG CONNECTION: WIRE VIEW PINK BLACK Crux 24-Pin Connector HOW TO DETERMINE IF THE VEHICLE HAS ANALOG SWC: Analog Steering Wheel Control (SWC) signal vehicles will have wires populated and line up to the PINK and BLACK wire on the 24-Pin Crux connector. If one wire is missing then you will need to use Crux part number SWRFD-60. DIP SWITCH SETTINGS: FORD STEERING WHEEL CONTROL DIP SWITCH SETTING: RED to SWC Key 1 WHITE to SWC Key 2 SHIELD to SWC Ground (included in kit) AFTERMARKET RADIO DIP SWITCH SETTINGS: SWC 3.5MM PLUG ADAPTER: Use the supplied 3.5MM SWC Plug adapter for aftermarket radios that do not have a 3.5mm SWC jack. RADIO BRAND: DIP: 1 2 3 4 Dual, Fahrenheit, Jensen, Pioneer Power Acoustik, Soundstream Alpine Clarion Kenwood JVC Boss, Old Sony New Sony OFF OFF ON ON OFF OFF ON ON OFF OFF OFF OFF OFF ON ON OFF OFF ON ON ON OFF ON OFF ON OFF ON OFF OFF OFF OFF ON OFF SWC MODULE ON RADIO VEHICLE 1 2 3 4 5 6 7 8 DIP: 5 6 7 8 Ford OFF OFF OFF OFF SWRFD-60L SWC MODULE ON RADIO VEHICLE 1 2 3 4 5 6 7 8 NOTE: Insulate the Blue/Yellow and Green wires if not being used. 3.5MM SWC CABLE Plug in the 3.5MM to 4-Pin SWC cable to the SWC module.

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com rev.051619 4 of 7 RADIO REPLACEMENT SWC RETENTION + + R INTERFACING SOLUTIONS DKFD-60L Radio Replacement Interface with Steering Wheel Control Retention with Dash Kit for FORD, LINCOLN & MERCURY VEHICLE APPLICATIONS: FORD 2007 – 2010 Edge 2008 – 2012 Escape** 2007 – 2010 Expedition 2006 – 2010 Explorer 2007 – 2010 Explorer Sport Trac 2009 – 2008 F-150 2009 – 2012 F-150* 2008 – 2012 F-Series Super Duty 2005 – 2007 Five Hundred 2007 – 2008 Focus 2004 – 2007 Freestar 2005 – 2007 Freestyle 2006 – 2009 Fusion 2005 – 2009 Mustang 2008 – 2009 Taurus LINCOLN 2006 – 2008 Mark LT 2007 – 2010 MKX (Nav only) 2007 – 2011 Navigator (Nav only) MERCURY 2008 – 2010 Mariner** 2006 – 2009 Milan 2005 – 2007 Montego 2004 – 2007 Monterey 2006 – 2010 Mountaineer 2008 – 2009 Sable MAZDA 2009 – 2011 Tribute** *Not compatible on vehicles equipped with acclimated radio/climate control panel. **Compatible with vehicles equipped with factory navigation radio only. Compatible Ford SWC Types: Type 1 4-Button Type 2 4-Button Type 3 5-Button Type 4 6-Button

2. Insert pocket into lower section of kit from rear & lock into slots of mounting brackets. 3. Insert IS O mountable radio between IS O mount brackets and loosely attach to sides of radio using screws provided with radio when possible or screws supplied with kit. 4. S lide radio forward or backward for desired look and tighten screws. 5. Attach a rear support bracket to the rear of the new radio and adjust as necessary to support the weight of the radio (Optional) SINGLE ISOMOUNT INSTALLATION INSTRUCTIONS Fig. A Fig. B 1. Attach left and right mounting brackets to the kit as shown in the figure below. 2. Insert IS O mountable radio between IS O mount brackets and loosely attach to sides of radio using screws provided with radio when possible or screws supplied with kit. 3. S lide radio forward or backward for desired look and tighten screws. 4. S upport the rear of the radio component with back strap (optional). DOUBLE DIN MOUNT INSTALLATION INSTRUCTIONS Remove shaded tabs on left and right sides of the brackets (Right side not shown) Fig. D Fig. E Fig. C FOR FIGURE D REMOVE SHADED MOUNTING TABS ON BOTH LEFT AND RIGHT BRACKETS FOR: FORD ESCAPE MAZDA TRIBUTE MERCURY MARINER FOR FIGURE E REMOVE SHADED MOUNTING TABS ON BOTH LEFT AND RIGHT BRACKETS FOR: 2009-14 FORD F-150 FOR FIGURE C REMOVE SHADED MOUNTING TABS ON BOTH LEFT AND RIGHT BRACKETS FOR: FORD EXPLORER EXPLORER SPORT TRAC FORD FUSION LINCOLN ZEPHYR MERCURY MILAN MERCURY MOUNTAINEER For all vehicles listed below, remove the shaded mounting tabs on both left and right brackets. BRACKET PREPARATION Fig. A FOR FIGURE A REMOVE SHADED MOUNTING TABS ON BOTH LEFT AND RIGHT BRACKETS FOR: FORD 500 2004-08 FORD F-150 FORD FREESTYLE FORD MUSTANG FORD TRANSIT CONNECT TAURUS/TAURUS X MERCURY MONTEGO LINCOLN MARK LT Fig. B FOR FIGURE B REMOVE SHADED MOUNTING TABS ON BOTH LEFT AND RIGHT BRACKETS FOR: FORD FREESTAR FORD FOCUS 2005-08 FORD SUPER DUTY MERCURY MONTEREY FOR FIGURE F REMOVE SHADED MOUNTING TABS ON BOTH LEFT AND RIGHT BRACKETS FOR: 2009-15 FORD SUPER DUTY Fig. F RADIO REPLACEMENT SWC RETENTION + + R INTERFACING SOLUTIONS Radio Replacement Interface with Steering Wheel Control Retention with Dash Kit for FORD, LINCOLN & MERCURY Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311 phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com rev.051619 5 of 7

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com rev.051619 6 of 7 RADIO REPLACEMENT SWC RETENTION + + R INTERFACING SOLUTIONS DKFD-60L Radio Replacement Interface with Steering Wheel Control Retention with Dash Kit for FORD, LINCOLN & MERCURY NOTE: S ee illustration A on page 2 for bracket preparation 1. Open the storage compartment located above the R adio/Vent trim bezel. 2. S tarting from the top edge and working your way down the sides toward the bottom, carefully pry the R adio/Climate control trim bezel forward, disconnect all harnesses from the rear of the trim bezel and remove bezel. 3. R emove the (4) 9/32 screws securing the radio to the sub-dash. Carefully pull radio forward, disconnect all harnesses and antenna lead and remove radio. DASH DISASSEMBLY INSTRUCTIONS 2005-07 FORD FREESTYLE NOTE: S ee illustration B on page 2 for bracket preparation 1. Carefully unclip and remove the radio/climate control trim bezel from around the factory radio. 2. Disconnect the harnesses from the rear of the radio/climate control bezel and remove bezel. 3. R emove the (4) 9/32 screws securing the factory radio to the sub-dash. 4. Carefully pull radio forward, disconnect the wire harness and antenna lead from the factory radio and remove radio. DASH DISASSEMBLY INSTRUCTIONS 2004-07 FORD FREESTAR 2004-07 MERCURY MONTEREY NOTE: S ee illustration B on page 2 for bracket preparation 1. E ngage the parking brake. 2. For Automatic Transmission Vehicles only, insert key into the ignition and turn to the ON position and depress the brake pedal, (DO NOT S TAR T THE VE HICLE !) then place the shift lever into the lowest position. 3. Lower the steering column all the way down. 4. S tarting at the top edge of the dash trim bezel, carefully unclip and pull forward the dash trim bezel to access all the wire harness connectors attached to the features on the rear of the trim bezel. 5. Carefully disconnect all the connectors on the back side of the dash trim bezel and remove bezel. 6. R emove the (4) 9/32 screws securing the radio to the sub-dash. 7. Carefully pull radio forward, disconnect the wire harnesses and antenna lead from the rear of the radio and remove radio. DASH DISASSEMBLY INSTRUCTIONS 2005-08 FORD Super Duty NOTE: S ee illustration B on page 2 for bracket preparation 1. Carefully pry forward and unclip R adio/Climate control trim bezel and disconnect the 12 Volt R eceptacle plug from the rear of the bezel. 2. Lay the trim bezel assembly out of the way (Disconnecting the climate control cables or harnesses is not necessary). 3. R emove the (4) 9/32 screws securing the radio to the sub-dash. 4. Carefully pull Factory radio forward, disconnect the wire harness and antenna lead from the rear of the radio and remove radio. DASH DISASSEMBLY INSTRUCTIONS 2005-07 FORD FOCUS NOTE: S ee illustration A on page 2 for bracket preparation 1. Carefully remove the trim from around the gearshift. 2. R emove the (2) Phillips screws located under the center console lid. 3. Lift up on the emergency brake and carefully remove the center console. 4. Carefully unclip and remove the trim panels at the left and right side of the radio. 5. R emove the (4) 9/32 screws securing the radio trim bezel to the sub-dash, carefully pull trim bezel forward, disconnect all attached harnesses and remove trim bezel. 6. R emove the (4) 9/32 screws securing the radio to the sub-dash, carefully pull radio forward and disconnect all harnesses and antenna lead and remove radio. DASH DISASSEMBLY INSTRUCTIONS 2005-09 FORD MUSTANG NOTE: S ee illustration C on page 2 for bracket preparation 1. Open the center console and remove the (2) 9/32 screws from the center console shifter trim. 2. Carefully lift up on the center console shifter trim and disconnect the 12 volt receptacle harness and remove trim. 3. Carefully pry outward on the radio trim bezel to release the panel clips, then lift the lower sides upward and slightly outward to clear the shift lever. 4. Disconnect all harnesses from the radio trim bezel and remove bezel. 5. R emove the (4) 9/32 screws securing the radio to the sub-dash. 6. Pull radio forward, disconnect all harnesses and antenna lead and remove radio. DASH DISASSEMBLY INSTRUCTIONS 2006-10 FORD EXPLORER 2006-10 MERCURY MOUNTAINEER (NAV ONLY) 2007-10 EXPLORER SPORT TRAC NOTE: S ee illustration C on page 2 for bracket preparation 1. S tarting from the bottom, carefully pry the factory radio trim bezel from around the radio forward, disconnect all harnesses attached to the rear of the trim bezel and remove bezel. 2. R emove the (4) 9/32 screws securing the radio to the sub-dash. 3. Carefully pull radio forward, disconnect all harnesses and antenna lead and remove radio. DASH DISASSEMBLY INSTRUCTIONS 2006-09 FORD FUSION 2006-08 LINCOLN ZEPHYR 2006-09 MERCURY MILAN DASH DISASSEMBLY INSTRUCTIONS 2008-11 FORD ESCAPE 2008-11 MAZDA TRIBUTE/ MERCURY MARINER NOTE: S ee illustration D on page 2 for bracket preparation 1. Carefully pry the Vent assembly above the radio forward. 2. R emove the (2) 9/32 screws securing the top of the radio/Climate control assembly to the sub-dash. 3. Carefully pry the LOWE R 12 Volt/ US B/ Auxiliary plug panel forward, disconnect all attached harnesses and remove panel. 4. R emove the (2) 9/32 screws securing the lower edge of the R adio/Climate control assembly. 5. S et the parking brake.

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com rev.051619 7 of 7 RADIO REPLACEMENT SWC RETENTION + + R INTERFACING SOLUTIONS DKFD-60L Radio Replacement Interface with Steering Wheel Control Retention with Dash Kit for FORD, LINCOLN & MERCURY 6. R emove the shift lock cover and press the shift lock button down using a small screwdriver or pen and depress the brake pedal and move the shift lever all the way to the rear. 7. Carefully pull the entire R adio/Climate control assembly forward (you will need a second person for the next step). Be careful not to scratch the sides of the dash, or the shift lever. 8. R emove the (1) 5/16 bolt securing the Ground strap to the right side of the assembly. Pliers may be necessary due to the short length of the strap. 9. Pull the entire assembly forward and remove all attached harnesses and antenna leads and remove assembly. 10. R emove the (4) 9/32 screws from the sub-dash to be able to mount the install kit into the dash location. NOTE: S ee illustration E on page 2 for bracket preparation 1. Open the ashtray/pocket below the climate controls. 2. From behind the auxiliary panel located to the right of the cigarette lighter, carefully unclip and press the auxiliary panel forward to release, disconnect the attached harnesses(if applicable) and remove panel.(save for re-assembly) 3. R emove the (1) 9/32 screw securing the lower edge of the radio/climate control trim bezel. 4. R emove the rubber mat located above the top edge of the radio trim bezel or fascia. 5. R emove the (2) 9/32 screws located under this mat. 6. Using a panel removal tool, carefully pry the left and right vent trim panels slightly outward to allow the edges of the Fascia of the R adio/Climate control bezel to be removed, (it is not necessary to remove the vent trims entirely). 7. Carefully unclip and remove the factory radio/climate control bezel, or fascia. 8. R emove the (4) 9/32 screws securing the radio (or radio sub-chassis) to the sub-dash. 9. Carefully pull the radio forward, disconnect all attached harnesses and antenna lead and remove radio (or radio sub-chassis). (Center Console shift Vehicles) 1. S et the Parking Brake. 2. Open the center console armrest lid and remove the (3) lower Torx screws securing the lid/hinge assembly to the pocket cavity of the center console. 3. Carefully unclip and remove the thin panel below the cigarette lighter. 4. From behind the auxiliary panel located to the right of the cigarette lighter, carefully unclip and press the auxiliary panel forward to release, disconnect the attached harnesses(if applicable) and remove panel.(save for re-assembly) 5. R emove the (1) 9/32 screw securing the lower edge of the radio/climate control trim bezel. 6. R emove the rubber mat located above the top edge of the radio fascia. 7. R emove the (2) 9/32 screws located under this mat. 8. Insert key into the ignition and turn to the ON position, (DO NOT S TAR T the vehicle). 9. Depress the brake pedal and move the shift lever back. 10.Lift up and remove the shift trim/drink holder assembly. 11. Starting from the rear top edge of the center console, carefully lift up and unclip the entire top trim section that meets the lower edges of the Center Stack Vent/radio side trim panels. 12.Using a panel removal tool, carefully pry the left and right vent trim panels slightly outward to allow the edges of the Fascia of the R adio/Climate control bezel to be removed, (it is not necessary to remove the vent trims entirely). 13.Carefully unclip and remove the factory radio/climate control bezel, or fascia. 14.R emove the (4) 9/32 screws securing the radio (or radio sub-chassis) to the sub-dash. 15.Carefully pull the radio forward, disconnect all attached harnesses and antenna lead and remove radio (or radio sub-chassis). DASH DISASSEMBLY INSTRUCTIONS 2009-12 FORD F-150 / 2013-14 FORD F-150 (with Classic Dash) DASH DISASSEMBLY INSTRUCTIONS 2009-15 FORD SUPER DUTY PICKUP NOTE: S ee illustration F on page 2 for bracket preparation 1. Using a Flat blade screwdriver, insert the screwdriver blade into the slots located on the bottom edges of each the 12 Volt receptacle and S ync panels located below and to the sides of the factory climate controls, gently pull each panel forward to release and rest out of the way. 2. R emove the individual 9/32 screw located behind each panel removed in step 1 above. 3. Carefully pull the entire R adio/Climate Control panel with Vents forward to release and rest out of the way. 4. R emove the (4) 9/32 screws securing the radio to the sub-dash. 5. Carefully pull the radio forward, disconnect the attached wire harnesses and antenna adapter and remove radio. NOTE: S ee illustration A on page 2 for bracket preparation 1. Carefully Pry radio dash trim bezel outward, disconnect all harnesses from back of trim bezel and remove bezel. 2. R emove the (4) 9/32 screws securing the factory radio to the sub-dash. 3. Pull radio forward, disconnect all harnesses and antenna lead and remove radio. DASH DISASSEMBLY INSTRUCTIONS 2004-08 FORD F-150 (EXCLUDES HERITAGE MODELS) 2006-07 LINCOLN MARK LT 2012-2013 Transit Connect NOTE: S ee illustration A on page 2 for bracket preparation 1. Carefully Pry radio dash trim bezel outward, disconnect all harnesses from back of trim bezel and remove bezel. 2. R emove the (4) 9/32 screws securing the factory radio to the sub-dash. 3. Pull radio forward, disconnect all harnesses and antenna lead and remove radio. DASH DISASSEMBLY INSTRUCTIONS 2005-07 FORD 500 2005-07 MERCURY MONTEGO 2008-09 TAURUS/TAURUS X