i.am+ R Manual 

ACHIEVE MORE WITH YOUR iAm SANITISING AIR DRYER Sanitising Air Dryer complete with AMF filter Replacement AMF required every 6 months To place orders for all consumable products and upgrades please contact 0800 354 800 ANTI-FIBRE MIGRATION ANTI-BACTERIAL FILTER CHARCOAL FILTER AIR MANAGEMENT FILTER AMF FILTER SLIDES IN TO AMF FILTER HOLDER AMF CARTRIDGE SLIDES INTO AMF CARTRIDGE HOLDER AMF FILTER AMF CARTRIDGE HOLDER POSITIVE CHARGE OR FRAGRANCE BOOSTER BOTTLES (24ML 6 MONTHS) BOTTLES AND HOLDER SLIDE INTO THE MACHINE

• The AMF Filter must be changed every 6 months. These can be purchased through your nearest agent. • The appliance is to be installed by qualified persons only in the environment for which the machine has been designed including washrooms and bathrooms. • The appliance must be returned to point of purchase for any defects in workmanship and materials to be REPAIRED by the manufacturer or its designated service representative and the original unit shall be returned to the customer in the condition it arrived, including any cosmetic or component damage as a result of misuse or abuse, save for the defects indicated above. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and they understand the hazards involved. Children must not play with the appliance. Cleaning and user maintenance must not be undertaken by children. If the power supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. The appliance must be disconnected from the supply mains prior to cleaning or other maintenance. Description Fully automatic •Vandal resistant die cast or polycarbonate case •High velocity airflow and high wattage element for rapid drying •Unique base plate incorporating a power socket allows the unit to be removed without mains disconnection •Solid state infra-red control (no electromechanical devices) • Thermal protected motor and element •Powder coated (die cast) for increased durability, chemical resistance and electrical insulation. Performance Data Operating noise level: 78-82 dB Air Velocity: 11,800 ft/min, 55.88 m/s Air Temp at Outlet (standard): 45°C, 113.0⁰F Air Temp at Outlet (eco): 29.5°C, 85.1⁰F Thermal Cut Out: 70°C (+/- 5°C), 158.0⁰F (+/-41⁰F) Electrical & Electronic Data Operating voltage range: 21 0 - 240 VAC Eco Version Electricity Rating: 590 watts Element Version Electricity Rating: 1 250-1500 watts Motor: 590 Watt 13000 RPM - thermal protection Range: Factory Set at 150mm Dimensions Base: S @ 325mm x 250mm R @ 330mm x 235mm Projection: S @ 185mm, R @ 185mm Height x Width: S @ 340mm x 235mm R @ 330mm x 235mm Packaging Dimensions: 350mm x 260mm x 205mm (EXTERNAL) International Limited Warranty This product is warranted to be free from defects in workmanship and materials for a period of five (5) years from date of purchase and is conditional upon fitting at time of installation and constant use and replacement every six (6) months of the AMF Filter provided. If repairs are necessary during this period due to manufacturing defects, the product will be either repaired or replaced free of charge with an equivalent product at our discretion. SATISFACTORY PROOF OF PURCHASE DATE MUST BE FURNISHED AT THE TIME OF NOTIFICATION OF THE DEFECT FOR ANY CLAIM UNDER THIS WARRANTY TO BE ENFORCEABLE. This warranty will become invalid if the product has been subjected to modifications, abuse, improper treatment, non-compliance with the constant use & replacement every six (6) months of the AMF Filter and/or if any defect is caused by repairs made by any unauthorised person. There are no warranties expressed or implied except for those which are stipulated herein and those which are implied and cannot be excluded under law provided that in those countries and states where it is impossible to limit warranties of merchantability and or fitness for a particular purpose to the duration of this warranty they shall be regarded as being so limited. Incidental and consequential damages of all kinds whatsoever are excluded if and to the extent to which it is possible to do so in law. Our goods come with guarantees that cannot be excluded under the New Zealand Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. AND SANITIZER After Sales, Service and Warranty support e-mail: [email protected] Colour Options (Standard) Gloss White, Matt Black or Brushed Satin. Other colours available as special request with MOQ. Mechanical Data Weight for R & S: 5.3 kg (BOXED) Base plate: Passivated Zinc Plated Steel Fan Housing: Nylon 66 Vydyne 909 25% GF Rotor: Nylon 66 Vydyne 909 25% GF + Nylon 66 Vydyne Resin ECO315 Material Specification Case Construction: R-Model: Die Casting Aluminium or Polycarbonate housing S-Model: Die Casting Aluminium only Optional Extras • Buyer Branding (Faceplate) • LCD Screen

INSTALLATION, MAINTENANCE AND WARRANTY INSTRUCTIONS WARNING • The appliance is only intended to be installed or maintained by qualified personnel. • The appliance is not intended for use by young children or infirmed persons without supervision. Young children should be supervised to ensure that they do not play with the appliance. • Means for all pole (Live & Neutral) disconnection (air-gap of at least 3mm) must be included for fixing wiring. The disconnection device must be installed in accordance with the wiring rules. • For appliances fitted with a supply cord and plug - if the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons. Recommended installation height from floor to underside MEN: 1240 mm WOMEN: 1100 mm DISABLED: 900 mm INSTALLATION Always ensure: The appliance is mounted clear of swinging doors or any other feature likely to cause damage. The mounting surface is even to avoid distortion of the base plate. The front of the appliance is able to swing down through 90° to allow disassembly. Housing may get damaged and require being support by one hand during changing of accessories. Avoid placing the machine over a pedestal or bench top as this may trigger the sensor unnecessarily. For bench top installation, it is recommended that the appliance be mounted at least 300mm above bench tops. TO INSTALL 1. Place the back plate against the wall and with the aid of a spirit level (Bubble Level) 2. Mark out the 5 mounting holes on the bottom of the back plate - 3. Determine the electrical connection method. a) For fixed wiring installation, ensure the cord passes through the supplied grommet in the top right hand corner of the back plate. b) For wiring to the nearest power point, break the appropriate tab (left or right) from the bottom of the rubber seal and install the power cord. c) Hand Dryers which have a power cord (not fitted), measure the length between the dryer and the power outlet and cut to remove excess cord before fitting. 4. Secure the back plate to the wall using 5 x 12 gauge wood screws, 6mm masonry bolts or similar. 5. Ensure the appliance is connected to an electrical circuit with adequate capacity and the necessary safety features (i.e. RCD), as per local regulations. 6. THE APPLIANCE MUST BE CORRECTLY EARTHED. 7. Fit the case to the back plate by holding the case at 90º and then sliding the case across and connect the internal power cable to the defeat switch cover. Ensure that the cable is correctly routed to prevent damage to the internals of the machine. 8. Rotate the case to the vertical, and apply moderate pressure on the front of the case to compress the back plate seal, while operating the key lock to secure the appliance. Drawing 1: S Back Plate Drawing 2: R Back Plate Drawing 3: Mains Power After Sales, Service and Warranty support e-mail: [email protected]

be performed: Procedure: 1. To ensure there is no power to the appliance, disconnect the power to the appliance prior to any maintenance or cleaning. 2. Open the appliance using the key lock (the power to the unit will automatically disconnect via the power defeat switch when cover is opened). Disconnect 3-pin plug on internal power cable from defeat switch cover. 3. Support the cover at an angle of approx. 90° and remove the AMF Filter from the holder by gently pulling out the AMF Filter. Do not allow the unit to drop down. 4. Insert new AMF Filter and ensure it 'clicks' into place. 5. Check the length of the motor brushes. Replace if less than 4mm. 6. Reconnect the internal power cable into the defeat switch cover. 7. Close and lock the unit. Exterior Cleaning: If the machine requires cleaning, only non-abrasive liquid cleaners may be used with a soft cloth. Take care not to wet any electrical components. SAFE WORK PROCEDURE Opening the machine Utilise the key supplied with the unit. Hold the Housing with one hand and the keys with the other, and unlock the machine. Gently allow the housing to tip open, whilst supporting the cover. Changing of accessories To open the housing, holding the key with one hand, place the other hand on the front of the machine to support the machine and slowly lower the housing to enable access to the accessories within the machine. AVOID allowing the machine to drop freely as it may damage the machine and the wall it is attached to. Continue to support the machine and use the hand previously holding the keys to change any of the accessories. Closing the machine Rotate the case back to the vertical, and apply moderate pressure on the front of the case to compress the back plate seal, while operating the key lock to secure the appliance. Remove the key when completed. Test unit by waving hand under sensor. After Sales, Service and Warranty support e-mail: [email protected]