Dedicated Micros TransVu Express Quick Start Manual

MI-Q-TVE/E2-0 Installing the Hard Drive The hard drive for the unit is provided un-installed. 1) Unlock the keylock on the front of the TransVu Express and withdraw the caddy. 2) Remove from the protective packaging from the Hard drive and insert into the caddy. Ensure the pins on the hard drive are pointing away from the front of the caddy drawer and the label on the hard drive is facing upwards and visible when the hard drive is placed in the caddy. 3) Carefully slide the caddy back into the TransVu Express. Remember to lock the caddy into the TransVu Express using the keylock. Failure to do so will prevent the unit starting up. Connections Please ensure the following are available and have been tested prior to the installation: • 10 ~ 30VDC Vehicle Power Source • Crossed network cable required for web page setup • Active video signals. • Correctly terminated cable loom, please see TransVu Express installation manual for further information. • Desk or Laptop PC with CD ROM drive with Internet Explorer 5.5 upwards for unit configuration • Note that pin 35 of the connector provides a switched output of the input voltage NOT a 12V regulated supply WARNING: Operate the TransVu Express from the power source indicated on the label. Failure to do so may cause injury, and will invalidate the warranty. Under no circumstances make connections to this unit whilst power is applied. 37 way Connector Layout Numbers looking at the front of the male connector. 1 19 37 20 Read the Instructions First Read all safety and operating instructions and labels before working with the TransVu Express. This Quick Start Guide is not for use in isolation and should always be used in conjunction with the main user manuals. Please contact the supplier with any problems. Report any difficulties with this guide to Dedicated Micros at the UK office. Addresses and phone numbers are given in the user guides and also in the Contacts area of the website at: http://www.dedicatedmicros.com Servicing Do not attempt to service this unit. Opening or removing covers may expose dangerous voltages or other hazards. Refer all servicing to qualified service personnel. Lifting and Handling Always follow health and safety guidelines when lifting the unit from the box or installing the TransVu Express unit. Unpacking Remove all the items from the box and check components listed below are included. The TransVu Express package contains the following items: • TransVu Express unit • Mounting Plate • Rubber Shock Mounts • Installation CD ROM • Installation Guide • Configuration & Operation Guide • Setup Guide • Quick Start Guide (this document) If any of these items are missing, please contact the distributer Customer Services department. Location • Drilling extra holes in the casing of the unit will immediately invalidate the warranty. • The unit should be mounted away from any possible places where water may puddle during vehicle operation as the TransVu Express casing is not rated for submersion. The unit should be mounted on a secure base free from resonance and secondary vibrations using the mounting plate provided. • A fitment area of 290mm x 190mm x 90mm (11½” x 7½” x 3½” ) is required. • Extra space is required around to the plug area to ensure easy removal. • Refer to TransVu Express Installation and Configuration & Operation Guides for more information. Pin Description 1 Monitor Output (1V p-p CVBS video) 2 Video ground 3 Camera 8 (1V p-p CVBS video) 4 Camera 5 (1V p-p CVBS video) 5 Video ground 6 Camera 4 (1V p-p CVBS video) 7 Camera 1 (1V p-p CVBS video) 8 Audio ground 9 Audio Input 2 (mic-level) 10 Relay output (negative side) 11 COM3 port: RS-232 TXD 12 10/100 Ethernet port: TX+ 13 10/100 Ethernet port: TX- 14 Alarm Input 1 15 Alarm Input 3 16 Switched power output – negative 17 Power input - negative: ground 18 Power input - negative: ground 19 Video ground Pin Description 20 Camera 7 (1V p-p CVBS video) 21 Camera 6 (1V p-p CVBS video) 22 Video ground 23 Camera 3 (1V p-p CVBS video) 24 Camera 2 (1V p-p CVBS video) 25 Video ground 26 Audio Input 1 (line-level) 27 Relay output (positive side) 28 Alarm ground 29 Alarm Input 2 30 Ignition sense input 31 COM3 port: RS-232 RXD 32 COM3 ground 33 10/100 Ethernet port: RX+ 34 10/100 Ethernet port: RX- 35 Switched power output – positive (1A) 36 Power input - positive: 10V – 30V DC 37 Power input - positive: 10V – 30V DC 15 way Expansion Port Layout Numbers looking at the front of the male connector. 1 6 5 10 15 11 PIN NO. FUNCTION 1 POWER MANGER RS232-RXD 2 POWER MANGER RS232-TXD 3 GND 4 COM1 RS232-RXD 5 COM1 RS232-TXD 6 COM2 - RS485+/RS422_TX+ 7 COM2 - RS485-/RS422_TX- 8 GND 9 COM1 CTS 10 COM1 RTS 11 COM2 - RS422_RX+ 12 COM2 - RS422_RX- 13 GND 14 AUDIO OUT 0 line level 15 AUDIO OUT 1 line level

MI-Q-TVE/E2-0 LED’s The six status LEDs are on the opposite end of the unit to the connector. They are labelled as follows: HDD NET PWR REC FAIL CF/SD Description Function HDD Illuminates red to indicate power to the hard disk drive CF/SD Illuminates red to indicate power to the CF/SD slots PWR Illuminates green when Power is connected to the unit REC Illuminates green when the unit is recording NET Illuminates green when the unit is connected to the network FAIL Illuminates green until the unit senses a failure condition Accessing & Configuring the Unit The unit can be configured either on the local monitor or over the network using a PC with Internet Explorer or similar browser. Both have near identical menu interfaces. Accessing the menus on a PC web browser Locating the Unit IP address The IP address of the unit is required to access the webpages. It can be identified from the configuration menu pages using the local monitor, press the MENU button on the IR Remote Control and navigate to the System Settings->System menu to find the DHCP assigned IP address. Note: The unit can be connected to a DHCP network environment via the 15 way connector to allow an IP address, subnet mask and default gateway to be automatically be allocated by the network DHCP Server (DHCP is enabled by default). Note: If a DNS (Domain Name Server) address is not to be used, it is strongly advised that a fixed IP address be assigned (a DHCP assigned address can change without notification i.e. following power failure). A fixed IP address can be assigned via the Network Settings- >Network menu. For information on locating the unit’s IP address via a PC and serial port connection, refer to Appendix D in the installation manual. Default DNS Address It is recommended that a DNS (Domain Name Server) address be configured. Assigning a recognisable name can help a remote user to locate the unit. If no System name is allocated to the unit, the default DNS address will be: machine serial number.yourdomain.com • is displayed in the System menu page and also on the underside of the unit. • is the name assigned to your DNS network. The default DNS address can be renamed via the Network Settings -> Network menu. Following renaming, the DNS address will be: yourname.yourdomain.com • ’ yourname‘ is the name assigned via the Network menu. • is the name assigned to your DNS network Note: To activate an assigned DNS address, it will be necessary to reboot the unit. The unit can be rebooted via System Settings:>Maintain-> Reset. IMPORTANT: To set the time and date on the unit, navigate to System Settings->Time and Date. Accessing the Configuration Webpages The unit can be configured using the webpages. To access these: 1. Launch Internet Explorer (or similar web browser package). 2. Type the URL for the unit (IP or DNS address). 3. The Opening menu page will be displayed.